Search

A fiber curvature sensor based on a Mach–Zehnder Interferometer (MZI) constructed using the waist-enlarged technique to splice a segment of non-zero dispersion-shifted fiber (NZ-DSF) between two segments of single mode fiber (SMF) is proposed and experimentally demonstrated. All fabricated sensors presented an improvement in their curvature sensitivity when they were coated with polydimethylsiloxane (PDMS) polymer. The sensor that exhibited the best performance was 6.5 cm long, with a curvature sensitivity of 8.27 nm/m−1 in a range of 0.69 m−1 (from 1.08 to 1.77 m−1). This sensitivity is 3.22 times higher than that of the sensor without polymer. Additionally, the sensor coated with polymer exhibited cross-sensitivity that is 2.23 times smaller than the sensor without polymer. The easy fabrication and notable performance of this device makes it alluring for structural health monitoring.

A ratiometric fiber optic temperature sensor based on a highly coupled seven-core fiber (SCF) is proposed and experimentally demonstrated. A theoretical analysis of the SCF’s sinusoidal spectral response in transmission configuration is presented. The proposed sensor comprises two SCF devices exhibiting anti-phase transmission spectra. Simple fabrication of the devices is shown by just splicing a segment of a 2 cm long SCF between two single-mode fibers (SMFs). The sensor proved to be robust against light source fluctuations, as a standard deviation of 0.2% was registered in the ratiometric measurements when the light source varied by 12%. Its low-cost detection system (two photodetectors) and the range of temperature detection (25 °C to 400 °C) make it a very attractive and promising device for real industrial applications.

In this paper, a ratiometric approach to sensing temperature variations is shown using specialty fiber optic devices. We analyzed the transmission response of cascaded segments of multicore fibers (MCFs), and dissimilar lengths were found to generate an adequate scheme for ratiometric operation. The perturbation of optical parameters in the MCFs translates to a rich spectral behavior in which some peaks increase their intensity while others decrease their intensity. Thus, by selecting opposite-behavior peaks, highly sensitive ratiometric measurements that provide robustness against spurious fluctuations can be performed. We implemented this approach using seven-core fiber (SCF) segments of 5.8 cm and 9.9 cm. To test the system’s response under controlled perturbations, we heated one of the segments from ambient temperature up to 150 °C. We observed defined peaks with opposite behavior as a function of temperature. Two pairs of peaks within the interrogation window were selected to perform ratiometric calculations. Ratiometric measurements exhibited sensitivities 6–14 times higher than single-wavelength measurements. A similar trend with enhanced sensitivity in both peak pairs was obtained. In contrast to conventional interferometric schemes, the proposed approach does not require expensive facilities or micrometric-resolution equipment. Moreover, our approach has the potential to be realized using commercial splicers, detectors, and filters.

A stable, single, and dual-wavelength erbium-doped fiber laser (EDFL), based on two Mach–Zehnder interferometers (MZIs), arranged in a cascade configuration, was proposed for experimental purposes. Both MZIs were assembled by splicing a capillary hollow-core fiber (CHCF) section between two multimode fibers (MMFs) segments. The novelty of this single and dual-wavelength EDFL is that the switchable operation of the laser is achieved by thermally tuning the interference pattern of one MZI and not by adjusting the polarization state inside the fiber ring cavity. The maximum measured value of SNR was 58.9 dB for the single and dual-wavelength laser emissions. Moreover, the stable output power exhibited by this EDFL, in terms of minimal power and wavelength fluctuations, at 0.05 dB and 10 pm, was detected during the single and dual-wavelength operation. It is worth noticing that switching is achieved at exact wavelength locations with a separation of 1.8 nm and not randomly, as reported by other works. These features make this switchable EDFL an appealing candidate for application in optical fiber communication systems and fiber sensing.

In this paper, we propose a highly sensitive temperature sensor based on two cascaded Mach–Zehnder interferometers (MZIs) that work using the Vernier effect. The all-fiber MZIs were assembled by splicing a segment of capillary hollow-core fiber (CHCF) between two sections of multimode fibers (MMFs). This cascaded configuration exhibits a temperature sensitivity of 1.964 nm/°C in a range from 10 to 70 °C, which is ~67.03 times higher than the sensitivity of the single MZI. Moreover, this device exhibits a high-temperature resolution of 0.0153 °C. A numerical analysis was carried out to estimate the devices’ temperature sensitivity and calculate the magnification of the sensitivity produced by the Vernier effect. The numerical results have an excellent agreement with the experimental results and provide a better insight into the working principle of the MZI devices. The sensor’s performance, small size, and easy fabrication make us believe that it is an attractive candidate for temperature measurement in biological applications.

In this paper, we propose and experimentally demonstrate a simple technique to enhance the curvature sensitivity of a bending fiber optic sensor based on anti-resonant reflecting optical waveguide (ARROW) guidance. The sensing structure is assembled by splicing a segment of capillary hollow-core fiber (CHCF) between two single-mode fibers (SMF), and the device is set on a steel sheet for measuring different curvatures. Without any surface treatment, the ARROW sensor exhibits a curvature sensitivity of 1.6 dB/m−1 in a curvature range from 0 to 2.14 m−1. By carefully coating half of the CHCF length with polydimethylsiloxane (PDMS), the curvature sensitivity of the ARROW sensor is enhanced to −5.62 dB/m−1, as well as an increment in the curvature range (from 0 to 2.68 m−1). Moreover, the covered device exhibits a low-temperature sensitivity (0.038 dB/°C), meaning that temperature fluctuations do not compromise the bending fiber optic sensor operation. The ARROW sensor fabricated with this technique has high sensitivity and a wide range for curvature measurements, with the advantage that the technique is cost-effective and easy to implement. All these features make this technique appealing for real sensing applications, such as structural health monitoring.