Search

Flash−butt welded rail is widely used in railway transportation; however, the welded joint is vulnerable after a long time of service, and its damage mechanism is controversial. Here, tensile and reciprocating friction tests were carried out to analyze the mechanical and tribological behaviors between the welded joint and the base metal of a U75VG rail. The results show that flash−butt welding promotes the pearlite to transform into ferrite, leading to a relatively low hardness value but high plasticity. In addition, the yielding and strength of the all−weld−metal specimen are 385 MPa and 1090 MPa, respectively, which are about 24.51% and 7.63% lower than that of the base metal specimen. It is worth noting that the elongation of the all−weld−metal specimen is 57.1% higher than that of the base metal specimen, and more dimples and tearing ridges can be detected on the fracture morphology of the all−weld−metal specimen, while the fracture morphology of the base metal specimen is filled with shallow dimples and cleavage planes. Moreover, the weld metal has a relatively higher COF (coefficient of friction), and its fluctuation amplitude is 1.25 times higher than that of the base metal, which is due to the rougher worn surface. Furthermore, the introduction of flash−butt welding changes the wear mechanism of the U75VG rail from adhesive wear and oxidation to fatigue wear and slight oxidation, and ultimately leads to more serious damage.

Abstract In many industrial devices, impact-sliding wear is caused by a variety of complex vibrations between the contacted interfaces. Under actual conditions, impact and sliding motions do not occur in only one direction, and different complex impact-sliding motions exist on the tribology surfaces. In this study, an impact-sliding wear test rig is developed to investigate the wear effect of different complex motions. Using this rig, multi-type impact-sliding wear effects are realized and measured, such as those derived from unidirectional, reciprocating, and multi-mode combination motions. These three types of impact–sliding wear running behavior are tested and the wear damage mechanism is discussed.

Abstract This paper investigates the self-loosening of threaded fasteners subjected to dynamic shear load. Three kinds of typical coatings, PTFE, MoS2, and TiN applied to bolts and nuts, are tested in this investigation. The study experimentally examines the loosening mechanisms of fasteners and assesses the anti-loosening performance of the three tested coatings based on their tightening characteristics, loosening curves, and the damage of thread surface. Additionally, the anti-loosening performance of the three coatings is compared under different load forms. The results indicate that the PTFE and MoS2 coatings have significant anti-loosening effect, whereas the anti-loosening performance of TiN coating is not satisfactory. It is also found that an appropriate increase of the initial tightening torque can significantly improve the anti-loosening effect. In addition, the microscopic analyses of PTFE and MoS2 coating reveal that a reduced initial tightening torque leads to fretting wear on the thread contact surfaces of fasteners, thereby aggravating the damage.

The influence of surface gas nitriding on wheel/rail rolling contact fatigue and wear behavior of CL60 wheel was studied on a new rolling contact fatigue/wear tester (JD-DRCF/M). The failure mechanisms of the wheel/rail surface after the gas nitriding and without gas nitriding on the wheel surface were compared and analyzed. The results show that the wheel with gas nitriding could form a dense and hard white bright layer which was approximately 25 μm thick and a diffusion layer which was approximately 70 μm thick on the wheel surface. Thus, the gas nitriding on the railway wheel not only significantly improved the wear resistance on the surface of the wheel, but also effectively reduced the wear of the rail; the results show that the material loss reduced by 58.05% and 10.77%, respectively. After the wheel surface was subjected to gas nitriding, the adhesive coefficient between the wheel/rail was reduced by 11.7% in dry conditions, and was reduced by 18.4% in water media, but even so, the wheel with gas nitriding still could keep a satisfactory adhesive coefficient between the wheel/rail systems, which can prevent the occurrence of phenomena such as wheel-slip. In short, the gas nitriding on the wheel surface can effectively reduce the wear, and improve the rolling contact fatigue resistance of the wheel/rail system. This study enlarges the application field of gas nitriding and provides a new method for the surface protection of railway wheels in heavy-duty transportation.

Reciprocating sliding friction tests were conducted on pure magnesium using a UMT-II tester. The tribo-chemical behavior was characterized using X-ray photoelectron spectroscopy (XPS) and electron probe micro-analyzer (EPMA), which showed that the tribo-chemical behavior of pure magnesium was due to a tribo-oxidation reaction. At room temperature, the debris layer on the worn surface contained Mg(OH)2, MgO, and MgCO3. According to the reciprocating sliding friction mechanism, the decomposition of MgCO3 into MgO should occur. XPS results revealed that the surface oxide layer, containing Mg(OH)2, and MgO, acted as a third layer to protect the surface. Apparently, Mg(OH)2·nH2O was the main tribo-chemical product of pure magnesium under sliding friction.