Search

Wireless sensor networks have gradually attracted widespread attention from academia and industry due to their wide application potential and versatility. In response to the coverage and routing issues of wireless sensor networks, this study combines the improved cuckoo algorithm and non-uniform clustering algorithm to design a coverage and routing optimization scheme for wireless sensor networks. Firstly, a wireless sensor network system is studied and built. Subsequently, the traditional cuckoo algorithm is optimized using the Cauchy distribution, and a coverage optimization scheme for wireless sensor networks based on the Cauchy distribution improved cuckoo algorithm is designed. Finally, by optimizing the dynamic range of network area and cluster radius respectively to improve the shortcomings of non-uniform clustering routing algorithms, a wireless sensor networks routing optimization scheme based on dynamic cluster radius optimization non-uniform clustering algorithm is designed. The research results indicated that the designed coverage scheme and routing scheme achieved good application results. Among them, the designed coverage scheme had a minimum running time of 0.89 minutes in node coverage problems and a maximum node coverage rate of 99.52%. The designed routing scheme had a minimum running time of 1.47 minutes and an energy loss rate of 0.84% in the routing optimization problem. In summary, the coverage scheme and routing optimization scheme designed by this research institute have good application effects and can provide certain technical support for the application of wireless sensor networks in other fields.

The multi-Fano interference, which is obtained through the simultaneous acquisition of bright and dark states in different phase transitions of Eu3+ : BiPO4 (7 : 1, 6 : 1, 1 : 1, and 0.5 : 1) and Eu3+ : NaYF4 (1 : 1/4) crystals, were reported in this work. Multidressed spontaneous four-wave mixing and multidressed fluorescence (multiorder) were adopted to optimize the strong photon–phonon nested dressing effect, which results in more obvious multi-Fano interference. Firstly, the multi-Fano is produced through interference in continuous and multibound states. Secondly, five multi-Fano dips are originated from the nested five dressings (one photon and four phonons) under symmetrical splitting of 7F1 energy level. It is found that the pure H-phase (0.5 : 1) sample exhibits the strongest photon–phonon dressed effect (five Fano dips). Further, high-order non-Hermitian exceptional points in multi-Fano interference were investigated by adjusting the ratio of Rabi frequency to dephase rate through nested photon and phonon dressing. The experimental results are validated by theoretical simulations, which may be applied to designing optoelectronic devices such as non-Hermitian multi-Fano interferences (multichannel) router.

To ensure the safety and correctness of the critical ‘mimic bracket’ components such as protocol proxies of mimic routers, a BGP (border gateway protocol) proxy was designed and implemented, and formal methods were applied to verify the safety and correctness of the BGP proxy.The BGP packets communicated between the peer routers and the master actor were monitored by the BGP proxy.The BGP sessions with the slave actors on behalf of peer routers were established, ensuring the consistency of the BGP protocol states for all actors.The formal specification of the BGP proxy was written based on separation logic.The VeriFast theorem prover was used to prove that the program had no memory safety problems such as null pointer reference.Furthermore, the formal verification of high-level attributes of each module in BGP proxy was also conducted to strictly ensure that the implementation met the specification.The implementation to proof code ratio of BGP proxy is about 1.8:1, and the implementation to proof labor hour ratio is about 1:3.The formally verified BGP proxy consume 0.16 seconds to process 100 000 BGP routes, which is about 7 times as long as the unverified one.Works done provide a reference for applying formal methods to verify the safety and correctness of critical components in mimic defense equipment and systems.

On-chip topological nanophotonic filtering and routing devices are important components of integrated nanophotonic chip. The device filters topological photonic states with multiple frequencies and routes them into different output ports, respectively. However, there is no effective method to implement such devices to date. Here, an on-chip topological five-channel filtering and routing device is realized for the first time. Topological edge states are constructed based on synthetic dimension, which can use dielectric materials to construct topological photonic states without external magnetic field. This method has advantages including simple structure, easy integration, and high signal-to-noise ratio. The implementation of on-chip topological multichannel filtering and routing device is of great significance to the development of topological nanophotonic devices.

We report a fiber loop quantum buffer based on a low-loss 2 × 2 switch and a unit delay made of a fiber delay line. We characterize the device by using a two-photon polarization entangled state in which one photon of the entangled photon pair is stored and retrieved at a repetition rate up to 78 kHz. The device, which enables integer multiples of a unit delay, can store the qubit state in a unit of fiber delay line up to 5.4 km and the number of loop round-trips up to 3. Furthermore, we configure the device with other active elements to realize integer multiplier and divider of a unit delay of a qubit. The quantum state tomography is performed on the retrieved photon and its entangled photon. We obtain a state fidelity ${\gt}$ 94 $\%$ with a maximum storage time of 52 μ s with an insertion loss of 5.56 dB. To further characterize the storing and retrieving processes of the device, we perform entanglement-assisted quantum process tomography on the buffered qubit state. The process fidelity of the device is ${\gt}$ 0.98. Our result implies that the device preserves the superposition and entanglement of a qubit state from a two-photon polarization-entangled state. This is a significant step towards facilitating applications in optical asynchronous transfer mode based quantum networks.

Time-correlated single-photon counting (TCSPC) is a powerful technique for time-resolved measurement of fast and weak light signals used in a variety of scientific fields, including biology, medicine, and quantum cryptography. Unfortunately, given its repetitive nature, TCSPC is recognized as a relatively slow technique. In the last ten years, attempts have been made to speed it up by developing multichannel integrated architectures. Yet, for the solutions proposed thus far, the measurement speed has not increased proportionally to the number of channels, reducing the benefits of a multichannel approach. Recent theoretical studies and prototypes have shown that it is possible to implement a new multichannel architecture, so-called router-based architecture, capable of optimizing the efficiency of data transfer from the integrated chip to the data processor, increasing the overall measurement speed. However, the first implementations failed to achieve the theoretical results due to implementation flaws. In this paper, we present a new logic for the router-based architecture that can operate at the same laser frequency and solve the issues of the previous implementation. Alongside the new logic, we present a new integrated low-jitter delay line combined with a new method for timing-signal distribution that allows the proper management of the pixel timing information. The new implementation is a step closer to realizing a router-based architecture that achieves the expected theoretical results. Simulations and bench tests support the results here reported.

Purpose. At present, the computer networks of the information and telecommunication system (ITS) of railway transport use the OSPF protocol, which does not allow taking into account several metrics when determining the optimal route. Therefore, there is a need to study the possibility of organizing routing in computer networks of rail transport ITS using a two-colonial ant algorithm. Methodology. According to the Two-ACO software model, created in the Python language based on the two-colonial ant algorithm, the optimal route in a computer network was determined. Two-ACO model inputs: computer network parameters (network adjacency matrix, number of routers); parameters of the ant algorithm (number of iterations; number of ants in the colony; number of elite ants; initial pheromone level; evaporation rate; parameter for adjusting the amount of pheromone deposition). Findings. The results of the Two-ACO model are presented in the form of graphs depicting the optimal paths: the criterion of the total delay on the routers (for the first colony of ants) and the number of hops (for the second colony of ants). Originality. According to the created Two-ACO software model for a computer network of 7 routers and 17 channels, a study of the time for determining the optimal path in a computer network by the number of ordinary and elite ants, evaporation rate and deposited pheromone was conducted. It is determined that it is enough to use the number of ants equal to the number of routers and have 2 elite ants in the colony, with 1000 iterations, evaporation rate from 0.2 to 0.7, and pheromone deposition by ants close to one. Practical value. Created Two-ACO software model using two colonies of ants on the following criteria: the total delay on the routers (for the first colony of ants) and the number of hops that make up the route (for the second colony of ants) allows you to parallel determine the optimal routes in a computer network of railway transport. It is estimated that for a computer network of 15 routers and 17 channels, it is sufficient to have 30 agents (two ants on top), the value of the pheromone deposited by the agents is close to one, and the evaporation rate is 0.4.

A three-dimensional (3D) nanoscale optical router is a much-desired component in 3D stacked optical integrated circuits. However, existing 3D routers based on dielectric configurations suffer from large footprints and nanoscale routers based on plasmonic antennas only work in a 2D in-plane scene. Here, we propose and experimentally demonstrate cross-layered all-optical 3D routers with nanoscale footprints. Optical slot antenna pairs are used to realize the routing of plasmonic signals between different layers for arbitrary direction in a broadband wavelength range. The routers are also integrated with waveguide directly for exploring further applications. Based on these router elements, a 3D network of optical butterfly interconnection is demonstrated for multi-directional all-optical data communication. The proposed configuration paves the way for optical cross-layer routing on the nanoscale and advances the research and applications for 3D plasmonic circuits with high integration density in the future.

Abstract The security of wireless routers receives much attention given by the increasing security threats. In the era of Internet of Things, many devices pose security vulnerabilities, and there is a significant need to analyze the current security status of devices. In this paper, we develop WNV-Detector, a universal and scalable framework for detecting wireless network vulnerabilities. Based on semantic analysis and named entities recognition, we design rules for automatic device identification of wireless access points and routers. The rules are automatically generated based on the information extracted from the admin webpages, and can be updated with a semi-automated method. To detect the security status of devices, WNV-Detector aims to extract the critical identity information and retrieve known vulnerabilities. In the evaluation, we collect information through web crawlers and build a comprehensive vulnerability database. We also build a prototype system based on WNV-Detector and evaluate it with routers from various vendors on the market. Our results indicate that the effectiveness of our WNV-Detector, i.e., the success rate of vulnerability detection could achieve 95.5%.

Plasmons, as emerging optical diffraction-unlimited information carriers, promise the high-capacity, high-speed, and integrated photonic chips. The on-chip precise manipulations of plasmon in an arbitrary platform, whether two-dimensional (2D) or one-dimensional (1D), appears demanding but non-trivial. Here, we proposed a meta-wall, consisting of specifically designed meta-atoms, that allows the high-efficiency transformation of propagating plasmon polaritons from 2D platforms to 1D plasmonic waveguides, forming the trans-dimensional plasmonic routers. The mechanism to compensate the momentum transformation in the router can be traced via a local dynamic phase gradient of the meta-atom and reciprocal lattice vector. To demonstrate such a scheme, a directional router based on phase-gradient meta-wall is designed to couple 2D SPP to a 1D plasmonic waveguide, while a unidirectional router based on grating metawall is designed to route 2D SPP to the arbitrarily desired direction along the 1D plasmonic waveguide by changing the incident angle of 2D SPP. The on-chip routers of trans-dimensional SPP demonstrated here provide a flexible tool to manipulate propagation of surface plasmon polaritons (SPPs) and may pave the way for designing integrated plasmonic network and devices.

The aim of the research is to study the effect of microwave Wi-Fi radiation on humans and plants. The paper investigates national standards for permissible exposure levels to microwave radiation, measures electric field intensity and justifies the point of view regarding the safe use of microwave technologies based on multiple plant cultivation experiments at different distances from a Wi-Fi router. The results demonstrate that the radiation of Wi-Fi routers significantly impairs the growth, development, yield and unexpected drought resistance of plants at short distances from the microwave source (up to 1 m to 2 m; –33 dBm to –43 dBm; >10 V/m). Slight effects are found up to about 4.5 m from a full-power home Wi-Fi router. As a result, suggestions are made for safe and balanced use of modern wireless technologies, which can complement occupational safety and health regulations.

Router is the network equipment for route the packet from one network segment to another in a bigscale network. Router can route packet because there is a routing table in router configuration. Routing table is anaddress list of source and destination address where the packet will be routed. There are two methods of routing tableconfiguration, static routing and dynamic routing. Static routing is a routing table configuration method where all ofrouting table content is configured manually, usually for a small scale of network. Dynamic network is a routing tableconfiguration method by the router automatically, usually for a big scale of network. A dynamic routing is built fromthe routing information collected by the routing algorithm. There are two routing algorithm, link-state and distancevector algorithm. This simulation will be built in GNS3 simulation software. Goal of this research is to compare theperformance between that two algorithm from two routing protocol that using each of those two algorithm. Thecomparison will be running between OSPF routing protocol on the link state routing protocol and EIGRP on thedistance vector routing protocol side. The result of this analysis and comparison of those two routing protocol isexpected to be a reference of choosing better routing protocol in building a network

Ultraviolet (UV) photonics-based device and equipment have various applications in sterilization, military covert communication, medical treatment, nanofabrication, gem identification and so on. The traditional constituent UV components are bulky, inefficient, expensive and easily aging under UV radiation. An all-dielectric metasurface offers a promising way to control the amplitude, polarization and phase of light by engineering the size, shape and distribution of its constituent elements. However, UV components based on all-dielectric metasurfaces are difficult to be realized, due to significant absorption loss for most dielectric materials at the UV region. Here we demonstrate the design of a UV metalens, composed of high-aspect-ratio aluminum nitride nanorods. The in-plane on-axis, off-axis and out-of-plane focusing characteristics have been investigated at representative UVA (375 nm), UVB (308 nm) and UVC (244 nm) wavelengths, respectively. Furthermore, we design UV router for mono-wavelength and multiple wavelengths, that is, guiding UV light to designated different spatial positions. Our work is promising for the development of UV photonic devices and would facilitate the integration and miniaturization of the UV nanophotonics.

At this time the exam using paper rated less cumbersome and inefficient. In this case the teacher will make difficult to assess the answers and take a long time to finish the job. In developing this system, the author is still in the development stage by using Banana Pi sebgai server, and use a router to a local network, this system is expected to facilitate the teacher to correct the test results. This test system uses CodeIgniter framework as a backend and frontend using material design. The system is easy to use and portable for a local network to connect them.

ABSTRACT: Cognitive radio sensor network (CRSN) is a new generation of communication systems that wants to solve the overcrowded spectrum utilization of the unlicensed bands. It has combined sensor networks and cognitive radio technology, so it has the challenges of energy restriction of sensors and also dynamic spectrum access of the cognitive radio network. On the other hand, considering both of these challenges in the routing protocol plays a basic role in network performance and we can’t apply the routing protocols that have been proposed for wireless sensor networks and cognitive radio networks, separately, in the CRSN. Therefore, this article has tried to provide a new spectrum and energy-aware routing protocol in which the source is able to choose the most stable route in the aspect of node residual energy or spectrum access probability. Not only can considering the nodal residual energy and spectrum access in the route discovery process avoid repetitive link failure, but it also can increase the network lifetime. This protocol has been compared with ESAC, SCR, ERP, and SER. The result of this comparison has shown that our protocol reduces end-to-end delay, control overhead, throughput, and lifetime in comparison to other protocols, especially in small-scale networks. ABSTRAK: Rangkaian sensor radio kognitif (CRSN) adalah generasi baru sistem telekomunikasi bagi menyelesaikan masalah kesesakan pada pemakaian band spektrum tidak berlesen. Ianya adalah kombinasi rangkaian sensor dan teknologi radio kognitif. Oleh itu, ia mempunyai cabaran sekatan tenaga pada sensor dan kemasukan spektrum secara dinamik pada rangkaian radio kognitif. Pada masa sama, dengan mengambil kira kedua-dua cabaran pada protokol rangkaian ini telah memainkan peranan asas pada prestasi rangkaian dan kami tidak boleh mengguna pakai protokol rangkaian yang telah diguna pakai pada rangkaian sensor tanpa wayar dan rangkaian radio kognitif secara asing dalam CRSN. Oleh itu, artikel ini cuba menyediakan spektrum baru dan pengawasan tenaga pada protokol rangkaian, di mana sumber boleh memilih laluan rangkaian yang stabil dengan mengambil kira pada aspek baki tenaga nod atau kebarangkalian akses spektrum. Selain itu, ianya dapat mengelakkan kegagalan laluan berulang juga menambahkan jangka hayat rangkaian. Protokol ini telah dibandingkan dengan ESAC, SCR, ERP dan SER. Perbandingan keputusan menunjukkan protokol ini mengurangkan kelewatan hujung-ke-hujung, mengawal kesesakan, mambaiki jumlah penghantaran dan menambah tempoh hayat berbanding protokol lain, khususnya pada rangkaian skala kecil.

The paper describes the process of smart space creation based on integration of Smart-M3 platform with a DD-WRT-based device. Smart-M3 is an open source platform which implements concept of smart space. Wi-Fi router is used as platform hosting which reduces the number of devices participating in smart space-based scenarios. The article covers a process of compilation and installation of Smart-M3 platform on DD-WRT-based Wi-Fi router. Evaluation shows that smart space organized this way can be used for scenarios with few participants. The authors developed “Smart-M3 Control Panel” web-service which allows users to control Smart-M3 platform by a graphical web interface. “Smart-M3 Control Panel” user can view the current status of platform; launch, stop, and reload it; view information storage content and change it; download log files; and change startup options. SocketIO interface was used for the user interaction with web service.

The virtualization of the Router’s Main Control unit function based on the x86 platform can provide support for several technologies including virtualization,Software Defined Network（SDN）and cloud computing for further applications.Traditional router code is developed on private network processor.In order to achieve traditional function of a router in a virtualized environment,we recompile the virtual network interface card’s board support package,drive and protocol stacks based on traditional router code.This method realizes the router’s code mirror running normally in Vmware virtual machines based on normal Windows platform.The feasibility is also verified by the sending and receiving packet test.Compared with the traditional method of programmable router virtualization,this method utilizes a pure software virtualization technology and it is based on VxWorks router protocol stack,which shows much better versatility and flexibility.

An eight-contact phase change data router is described. This device comprises a phase-change-material forming a short-pipe geometry with four metal contacts at each end. The device is configured to facilitate connection or isolation between two input and two output terminals (2×2) by amorphizing strips between pairs of “write” terminals. The short pipe geometry enables the implementation of a “swap” function in this 2-D thin-film device. The functionality of this device is demonstrated through 2-D electro-thermal simulations using Ge2Sb2Te5 parameters and field effect transistor access devices.

The major advantage of information-centric networking (ICN) lies in in-network caching. Ubiquitous cache nodes reduce the user’s download latency of content and the drain of network bandwidth, which enables efficient content distribution. Due to the huge cost of updating an entire network infrastructure, it is realistic for ICN to be integrated into an IP network, which poses new challenges to design a cache system and corresponding content router. In this paper, we firstly observed that the behavior pattern of data requests based on a name resolution system (NRS) makes an ICN cache system implicitly form a hierarchical and nested structure. We propose a complete design and an analytical model to characterize an uncooperative hierarchical ICN caching system compatible with IP. Secondly, to facilitate the incremental deployment of an ICN cache system in an IP network, we designed and implemented a cache-supported router with multi-terabyte cache capabilities. Finally, the simulation and measurement results show the accuracy of proposed analytical model, the significant gains on hit ratio, and the access latency of the hierarchical ICN cache system compared with a flat cache system based on naming routing, as well as the high performance of the implemented ICN router.

Este artículo presenta el desarrollo de un modelo de simulación para una red de sensores inalámbricos que se rige por las especificaciones IEEE 802.15.4 y ZigBee y que utiliza la configuración de la beacon habilitada. El modelo de simulación también implementa un modelo de consumo de energía para los tres tipos de nodossensores de la red (Coordinador ZigBee, Router y Dispositivo Final). El principal aporte de este trabajo radica en que por medio de la simulación se puede estimar el consumo de energía de un nodo-sensor y, de esta forma, analizar el consumo de energía de cada uno de los tipos del mismo. Así mismo, al poder estimar el consumo de energía del nodo-sensor, también se puede estimar su tiempo de vida. Por último, se analiza la razón, por la cual, el consumo de energía de los nodos es inversamente proporcional a la latencia de los datos dentro de la red.

In our daily life, inadvertent scratching may increase the severity of skin diseases (such as atopic dermatitis etc.). However, people rarely pay attention to this matter, so the known measurement behaviour of the movement is also very little. Nevertheless, the behaviour and frequency of scratching represent the degree of itching, and the analysis of scratching frequency is helpful to the doctor's clinical dosage. In this Letter, a novel system is proposed to monitor the scratching motion of a sleeping human body at night. The core device of the system is just a leaky coaxial cable (LCX) and a router. Commonly, LCX is used in the blind field or semi-blindfield in wireless communication. The new idea is that the leaky cable is placed on the bed, and then the state information of physical layer of wireless communication channels is acquired to identify the scratching motion and other small body movements in the human sleep process. The results show that it can be used to detect the movement and its duration. Channel state information (CSI) packet is collected by card installed in the computer based on the 802.11n protocol. The characterisation of the scratch motion in the collected CSI is unique, so it can be distinguished from the wireless channel amplitude variation trend.

We explore routing of propagating phonons in analogy with previous experiments on photons. Surface acoustic waves (SAWs) in the microwave regime are scattered by a superconducting transmon qubit. The transmon can be tuned on or off resonance with the incident SAW field using an external magnetic field or the Autler–Townes effect, and thus the reflection and transmission of the SAW field can be controlled in time. We observe 80% extinction in the transmission of the low power continuous signal and a 40 ns rise time of the router. The slow propagation speed of SAWs on solid surfaces allows for in-flight manipulations of the propagating phonons. The ability to route short, 100 ns, pulses enables new functionality, for instance to catch an acoustic phonon between two qubits and then release it in a controlled direction.

Wireless Sensor Network (WSN) has been widely considered as one of the most important category of networks. One of the applications of WSN is in Emergency Management Systems. Environmental monitoring systems, especially nuclear plants require transmission of emergency information in a dynamic manner. A conventional centralized management system may not be able to cope with huge number of sensors, rapidly changing topology and cannot assure the real-time transmission of emergency information. Decentralized System is presented to solve these problems. In Decentralized System, emergency information is distributed to the neighboring routers where each router transmits the emergency information to the sink by mutual coordination. In this paper, Decentralized System is proposed for the transmission of multiple emergency information with the coordination of neighboring routers without transmission collision between the routers.

Router alias resolution is one of hard problems and important steps for router level Internet topology measurement based on traceroute mechanism,and the topology characteristic of the generated router level topology graph has close relationship with the completeness of alias resolution.The graph with its degrees following power-law distribution was taken as the base-graph,and the shortest paths from one source to others were computed for simulating topology measurement.Experiment results show that it is very probable to see different topology characteristics between the derived graph and the base-graph due to incomplete alias resolution.Most importantly,for large-scale router level topology measurement,the completeness of alias resolution must be improved with the increasing number of probe sources,and in this way the derived topology graph could be approximate to the real topology graph.

The packet forwarding engine should provide not only the basic packet switching function,but also the reconfigurable ability for supporting the network processing functions evolving with time and space.Aiming at the above requirements,a component reconfiguration model of packet forwarding engine for the reconfigurable routers was proposed,and the program/circuit component running environment consisting of FPGA and network processers was designed and implemented based on the Pass-Through mode.The system implementation and application experimental results show that the packet forwarding engine for reconfigurable routers can support flexibly reconfiguration and mapping for the diverse service components,and it can provide high throughput and low-latency packet forwarding ability.

A novel cooperative caching scheme based on reconfiguration routers was proposed to accelerate the delivery of streaming media.Through cooperative caching for popular videos among the routers,the server capability,especially bandwidth requirements were decreased.Moreover,the traffic over the backbone network was dramatically reduced and user experience was also improved due to the edge routers providing services for the user quickly.Furthermore,implemented a prototype system is implemented to evaluate the scheme,and the results show great improvement over the state-of-the-art solutions.

This paper focuses on the analysis of network traffic public WIFI Chia, Cundinamarca, determining the presence of self-similar traffic and apply the algorithms SFARIMA and FARIMA. The results determine what the best predictor network traffic is.

In order to put Radio Frequency Identification (RFID) and Wireless Sensor Network (WSN) in a hybrid system, this paper presents the design and implementation of a RFID reader/router that can obtain information of both RFID tags and WSN sensor nodes and transmit the information through the WSN to the PC server. The RFID reader and WSN router are combined with both hardware and software. In hardware structure, CC2530 is used as micro controller and RF module for ZigBee wireless communication, and MF RC522 is used as reader RF chip. The software deals with both identity and sensing information and controls the routing. Experiment results show that the RFID reader/router achieves long distance identification, flexibility, scalability, and low cost. It also provides reliable and secured data transmission and broadens the communication range and application scope of RFID readers.

Much of the previous work on buffer design of router linecard mainly focus on how to implement large and fast packet buffers,however,lots of recent theories suggest that the optimal buffer size would no longer be a large one as expected,and a small buffer should be sufficient.A push based buffer setting strategy for high density linecard of small buffer size was presented,and a buffer-revenue function was introduced to give an evaluation on using efficiency of the small buffer.It is proved that the strategy can completely eliminate the HOL（header of line） blocking problem and the back-pressure mechanism of the existing strategies,moreover,the strategy can also get a better revenue when the buffer-revenue function is used to give an evaluation.

A new detection method: wobble defended M-MULTOPS（modified-multi-level tree for online packet statistics） structure was presented.Aiming at the change of network traffic in core routers,ABF（adapted bloom filter） algorithm to assemble destination addresses to the IP packets was employed.And it put forward M-MULPOTS struc-ture to analyze results of the ABF algorithm,monitoring changes of network traffic and detecting network flow ab-normity in real time.For making use of the Wobble-defended M-MULTOPS structure,the method can work steadily and exactly,even when the traffic of network is wobbling terribly by the pulse attack.And because the M-MULTOPS inherits the MULTOPS ’s flexible attribution,it declined the spending of system resources at maximum.A detection system em-ploying this method has been run successfully in routers as an individual module.

This paper presents a fully computerized method to backup the router configuration file. The method consists of a friendly graphical interface programmed by Java programming language The proposed method is compared with the two existing methods, namely: TFTP server method and Copy/Paste method. The comparison reveals that the proposed method has many advantages over the existing ones. The proposed method has been implemented on Cisco routers (series 2500, 2600 and 2800)

In order to improve the completeness of router level Internet topology measurement,the notion of self-contained destination set was defined first,and then existing destination selection methods were overviewed.After discussing the limitation of these existing methods,a viewpoint that the stub-network instead of the IP address should be taken as the sampling granularity was put forward,and a self-contained destination selection method that was termed all stub-networks coverage and two-step random selection was presented.Experiments show that this self-contained destination selection method guarantees the measurement completeness from the perspective of destination.

A very good method that can be used to protect a private network is the implementation of a firewall between Internet and Intranet. This firewall will filter the packets that transit the network according with the security policy defined at the system level. The SSL protocol allows verifying the identity of a WEB server based on a digital certificate issued by a certification authority. Secure data transport over the Internet is done by using encryption methods.

Teleskop bintang adalah sebuah perangkat instrument yang digunakan untuk melihat benda-benda langit yang jaraknya sangat jauh menjadi terasa dekat. Teleskop yang tersedia pada umumnya belum dilengkapi dengan sistem digital untuk pencitraannya dan otomatisasi untuk penentuan arahnya. Pada tugas akhir ini dibuat suatu sistem digital dan otomatisasi pada teleskop konvensional. Sistem digital digunakan untuk perekaman hasil yang didapatkan oleh teleskop dan ditampilakan pada komputer. Sistem otomatisasi dibuat untuk menentukan pergerakan sudut teleskop dengan sebuah GUI. Mekanik pergerakan teleskop diberikan 2 motor dc sebagai penggerak. Masing-masing motor dc berfungsi untuk menggerakkan tiap sumbu X dan sumbu Y. Digunakan sebuah sistem mikrokontroler menggunakan ATmega 32 sebagai pengolahan data. Fitur ADC mikrokontroler digunakan untuk mengubah data analog perubahan tegangan yang terjadi pada potensiometer menjadi perubahan data digital yang akan dikonversi menjadi nilai pergerakan perubahan sudut. Sistem ini ditambahkan sebuah router yang berfungsi sebagai akses poin untuk jalur pengiriman dan penerimaan data antara komputer dengan mikrokontroler. Ditambahkan sebuah wiznet yang mampu mengkonversi data dari komunikasi serial ke data protokol TCP/IP dan sebaliknya. Pengujian pergerakan sudut sumbu X dilakukan pada sudut 0, 45, 90, 135, 180, 255, 270, 315, dan 360 sedangkan pergerakan sumbu Y dilakukan pada sudut 0, 10, 20, 30, 40, 50, 60, 70, 80, dan 90. Hasil pengujian pada sumbu X dan Y didapatkan beberapa error pada titik-titik tertentu dengan tingkat kesalahan mencapai 3.8% untuk sumbu x dan 2.5% untuk sumbu y. Penentuan pergerakan sudut dilakukan melalui komputer dengan menggunakan komunikasi wi-fi.