Search

The 160 MiMi neutron detectors of SAFFRON, a 3D full-core mapping system developed at EPFL for the CROCUS zero-power reactor, have been simultaneously inter-calibrated in preparation for their in-core installation. An experimental setup was built to distribute up to 180 MiMi detectors radially at 15 cm around the Pu-Be neutron source of the CARROUSEL facility. An efficient inter-calibration methodology is presented: first, the azimuthal shape of the relative source strength is characterized by rotating 18 MiMi detectors distributed every 20º around the PuBe, followed by the simultaneous determination of the relative sensitivity of 160 MiMi detectors, distributed all around the Pu-Be source.

Highly localized in-core measurements are necessary for the validation of neutron transport calculations with high spatial resolution. In the present work, a miniature neutron detector developed at EPFL in collaboration with PSI was used to carry out a set of thermal neutrons counting measurements in the zero-power CROCUS reactor core within a spatial range in order of mm. The miniature detector, positioned close to the core reflector, shows a gradient of +(4.29 ± 0.10)% in the count rate profile in the radial direction within 1.3 cm, with higher values pointing towards the core reflector because of the higher share of neutrons in the thermal range. On the contrary, in a control rod guide tube the count rate gradient is -(4.37 ± 0.10)% and it is directed towards the core center. The measured values are compared with the azimuthal trend of the normalized 6Li reaction rate calculated with an iterative three-steps method performed with the Monte Carlo code Serpent 2. These measurements proved the feasibility of resolving spatial effects in the mm-range and they represent a basis for further investigating highly spatially-resolved phenomena in the CROCUS core.

Three 1-mm3 miniature fiber-coupled scintillators have been used to perform cm-wise resolution measurements of the thermal neutron flux within experimental channels of the SUR-100 facility, a zero power thermal reactor operated by the Institute of Nuclear Technology and Energy Systems at the University of Stuttgart. The detection system is developed at the École Polytechnique Fédérale de Lausanne in collaboration with the Paul Scherrer Institut. Thermal neutrons count rates were measured along the experimental channels I and II, which cross the reactor at the center and tangentially to the core, respectively. The reactor was modelled with the Monte Carlo neutron transport code Serpent-2.1.31. The comparison of experimental and computed reaction rate distributions showed a good agreement within the core region, with discrepancies within 2σ. An unexpected discrepancy, probably caused by a geometric inconsistency in the computational model of the reactor, was observed in the reflector region of the experimental channel I, where a 20% difference (i.e. 8σ) was found between experimental and simulated results. Significant discrepancies, respectively worth 10σ and 15σ, were noticed at distance, in the lead shielding region, for both experimental channels I and II. In addition, reaction rate gradients across the 2.6 cm and 5.4 cm diameters of both channels were measured. A horizontal reaction rate gradient of (9.09 ± 0.20) % was measured within 2.4 cm across the diameter of the experimental channel II, with a difference from computed results of 2%. The absence of a vertical reaction rate gradient inside the experimental channel I was confirmed by measurements.

We report in the present article on the successful observation using noise analysis of the lateral oscillation of one fuel rod by ±2.5 mm around nominal at 0.1 Hz frequency, using an mm3 miniature neutron scintillator at the rod level, and a BGO gamma detector seven meters away from the reactor core center. The experiment was conducted as part of the COLIBRI program in the CROCUS reactor, which is dedicated to the investigation of reactor noise induced by fuel vibrations. It consists in experiments on rod lateral displacement (static) and oscillation (dynamic) with different rods’ numbers at various relevant amplitudes and frequencies. Its main motivation is the increased amplitudes in the neutron noise distributions recorded in ex- and in-core detectors that have been observed in recent years in Siemens pre-Konvoi type of PWR reactors. The obtained experimental data are used for the purpose of code validation, especially within the framework of the European project CORTEX on reactor noise applications. During the first phase of COLIBRI, the observation of a spatial dependence of the perturbation noise, also called neutron modulation, was demonstrated. In the second phase of COLIBRI starting 2021, it is planned to use a core mapping array of neutron detectors to record its propagation. It consists in about 150 miniature scintillators coupled to optical fibers and SiPM readouts, to be distributed in the reactor core. As a feasibility test, experiments were performed using a miniature scintillator prototype placed on a fuel rod, and oscillating the instrumented rod or the one directly adjacent to the detector. In addition, it is theoretically possible to measure branching or perturbation reactor noise using gamma radiation. Following recent developments on gamma measurements in CROCUS, the fuel oscillation was simultaneously recorded with a gamma detection array, LEAF. Its large BGO detectors were used by placing them at the maximum distance to the core, i.e. seven meters away with a clear line of sight using an experimental channel through the shielding of the reactor cavity.

The present article provides an overview of the design of a three-dimensional (3D) full-core mapping system for the CROCUS reactor, operated at the École polytechnique fédérale de Lausanne (EPFL), Switzerland. The system is composed of 149 miniature neutron detectors distributed within the core double lattice at three main axial levels. The miniature detector technology is based on the optimization of the well-proven coupling of a miniature ZnS:6LiF(Ag) scintillator to a state-of-the-art silicon photomultiplier (SiPM) via jacketed optical fibers. The challenges in the mechanical design, the detector optimization, the core criticality, and the development of the acquisition electronics are strongly interconnected and their combination is addressed in this article. The 3D full-core mapping system is foreseen to be installed in CROCUS in autumn 2021 and it will pave the way for the investigation of 3D dynamic phenomena in nuclear reactor cores.

An advanced neutron detection system for highly localized measurements in nuclear reactor cores was developed and tested in the Laboratory for Reactor Physics and System Behaviour (LRS) at the École polytechnique fédérale de Lausanne (EPFL), Switzerland, in close collaboration with the Detector group of the Laboratory for Particle Physics (LTP) at the Paul Scherrer Institute (PSI), Switzerland. The miniature-size detector is based on the coupling of a ZnS:6LiF scintillator/converter screen of 1 mm2 and 0.2 mm thickness with a 10-m optical fiber, the latter being connected to a silicon photomultiplier (SiPM). In this development version, the output signal is processed via analog read-out electronics. The present work documents the characterization of a detection system prototype in the mixedradiation fields o f t he C ARROUSEL f acility a nd i ts t esting in the CROCUS zero-power reactor operated at LRS. The fibercoupled scintillator shows a linear response with the reactor power increase up to 6.5 W (i.e. around 108 cm-2s-1 total neutron flux), with a s ubsequent l oss o f l inearity d ue t o e lectronic dead time of the analog system. Nevertheless, the detector shows excellent neutron counting capabilities whether compared to other localized detection systems available at LRS, e.g. miniature fission chambers and an sCVD diamond detector.