Search

Series of experiments were performed to simulate the invasion of formation sand into and the plugging process of gravel-pack at different viscosities and flowing rates of fluid. Two types of formation sands with the medium size of 0.10 mm and 0.16 mm and the quartz sand and ceramsite of 0.6—1.2 mm were used in the experiments. A new viscosity-velocity index (the product of fluid viscosity and velocity) was put forward to characterize the influencing mechanism and law of physical property and flow condition of formation fluid on gravel-pack plugging, and a new method to optimize the production rate of wells controlling sand production with gravel-packing was proposed. The results show that the permeability of formation sand invaded zone and final permeability of plugged gravel-pack have negative correlations with viscosity and flow velocity of fluid, the higher the flow velocity and viscosity, the lower the permeability of formation sand invaded zone and final permeability of plugged gravel-pack will be. The flow velocity and viscosity of fluid are key factors affecting plugging degree of the gravel zone. The viscosity-velocity index (v-v index) can reflect the flow characteristics of fluid very well and make it easier to analyze the plugging mechanism of gravel zone. For different combinations of fluid viscosity and flow velocity, if the v-v index is the same or close, their impact on the final gravel permeability would be the same or close. With the increase of the v-v index, the permeability of plugged gravel zone decreases first, then the reduction rate slows down till the permeability stabilizes. By optimizing production and increasing production step by step, the optimal working scheme for sand-control well can reduce the damage to gravel-pack zone permeability caused by sand-carrying fluid effectively, and increase well productivity and extend the sand control life. Key words: gravel-pack, sand retention experiment, plugging law, viscosity-velocity index, working scheme, optimization method, plugging simulation

This paper presents a novel nonlinear control approach for a medium density fiberboard continuous hot pressing hydraulic system. Uncertainties, disturbances, and input saturation are explicitly taken into account. The proposed controller incorporates a smooth function by using a hyperbolic tangent function to substitute for the saturation nonlinearity in the system. Moreover, a novel backstepping-like slab thickness tracking controller is developed for a third-order cascade system within two steps. Taking advantages of radial basis function neural network (RBFNN) technique, a RBFNN-based reconstruction law is introduced to approximate the composite term consisting unknown function, disturbances, and saturation error. Lyapunov stability analysis shows that the designed control algorithm guarantees the asymptotic stability of the system with great robustness. Numerical simulation results are also exhibited to authenticate and validate the benefits of the proposed control scheme.

This paper presents a novel nonlinear control approach for medium-density fiberboard continuous hot pressing electro-hydraulic servo system (EHSS). The EHSS is subject to input saturation and unknown external disturbance. The approach is developed in the framework of the prescribed performance control design. The transient and steady behaviors are both considered by virtue of an appropriate performance function. A new robust adaptive neural control algorithm is then developed by introducing a dynamic surface control scheme. Moreover, the compensation control is designed for the nonlinear term arising from the input saturation. It is shown with the Lyapunov stability analysis that all the signals in the closed-loop system are semi-globally uniformly ultimately bounded. In addition, the system tracking performance regarding transient and steady-state behaviors is guaranteed effectively with input saturation via the designed control approach. Finally, numerical simulation results are presented to authenticate and validate the effectiveness of the proposed control scheme.

Hybrid white light emitting diodes (LEDs) have been developed utilizing micro-LEDs radiatively pumping down-conversion phosphor materials. The cyan InGaN/GaN multiple quantum wells LEDs with 95 μm in square are fabricated into 4 × 4 pixels as one unit in 4 in wafer by photolithography and inductively coupled plasma etching techniques. The relatively low turn on voltage and low leakage of cyan micro-LEDs indicate good electrical performance. A significant reduction in the efficiency droop characteristics of cyan micro-LED has been observed in comparison with that of standard green LED. Finally, based on a systemic optimization for white emission indexes, high-quality hybrid white light emission has been demonstrated by the combination of blue and cyan micro-LEDs with two types of phosphors, which have a high color rendering index up to 87 at the correlated color temperatures of 6500 K. It also demonstrates a way to adjust the color component by modifying the output power of cyan micro-LED in hybrid LED, showing a promising candidate in a large range of applications including micro-displays, bioinstrumentation, photolithography, and lab-on-chip systems in the future.

To improve the RadCom system of performing both data transmission and radar-sensing functions, here a waveform design method for orthogonal frequency division multiplexing (OFDM) signal is proposed to solve the problem of high range sidelobe level in radar detection process while maintaining a reasonable channel capacity. The method only transmits data in the sub-channels with preferable channel quality. Then, calculate the weight of the chosen subcarriers through the convex optimisation method to traditionally minimise the peak-to-sidelobe (PSL) ratio. Simulation results prove that, compared with traditional range sidelobe suppression method, this algorithm is more suitable for RadCom system.

Junction temperature (Tj) and current have important effects on light-emitting diode (LED) properties. Therefore, the electroluminescence (EL) spectra of blue and green LEDs were investigated in a Tj range of 120−373 K and in a current range of 80−240 mA based on accurate real-time measurements of Tj using an LED with a built-in sensor unit. Two maxima of the emission peak energy with changing Tj were observed for the green LED, while the blue LED showed one maximum. This was explained by the transition between the donor-bound excitons (DX) and free excitons A (FXA) in the green LED. At low temperatures, the emission peak energy, full width at half maximum (FWHM), and radiation power of the green LED increase rapidly with increasing current, while those of the blue LED increase slightly. This is because when the strong spatial potential fluctuation and low exciton mobility in the green LED is exhibited, with the current increasing, more bonded excitons are found in different potential valleys. With a shallower potential valley and higher exciton mobility, excitons are mostly bound around the potential minima. The higher threshold voltage of the LEDs at low temperatures may be due to the combined effects of the band gap, dynamic resistance, piezoelectric polarization, and electron-blocking layer (EBL).