Search

The frictional strength and sliding stability of faults are crucial in interpreting earthquake mechanisms and cycles. Herein, we report friction experiments on basalt fractures, using a self-designed triaxial apparatus that allows direct shear of samples under coupled hydro-mechanical conditions. Velocity-stepping (VS) and slide-hold-slide (SHS) experiments are performed on both bare and gouge-bearing surfaces of Xiashan basalt subjected to cyclic shear velocities at 1–30 μm/s, effective normal stresses of 1–5 MPa, and pore pressures of 70–300 kPa. The measured basalt friction coefficients are in the range of 0.67–0.74, which is sensitive to gouge thickness, normal stress, and water. Specifically, a reduction in friction coefficient is observed with an increment in gouge thickness, normal stress, and pore pressure. Based on the microscopic observation of the pre- and post-shearing sliding surfaces, this weakening effect in friction coefficient can be attributed to powder lubrication. Furthermore, the VS test results reveal predominantly velocity-strengthening behavior at investigated slip velocities, and this velocity strengthening behavior does not appear to be influenced by variations in normal stress, gouge thickness, and water. However, changes in sliding velocity and normal stress can lead to a shift between stable and unstable sliding. Specifically, stable sliding is favored by high sliding velocities and low normal stress applied in this study. Finally, we analyze the experimental data by calculating the rate-and-state parameters using the rate- and state-dependent friction (RSF) theory. Importantly, the calculated friction rate parameter (a-b) supports the velocity-strengthening behavior. Both frictional relaxation (Δμc) during hold periods and frictional healing (Δμ) upon re-shearing are linearly proportional to the logarithmic hold time, which may be attributed to the growth in true contact area with hold time. This study sheds light on the roles of sliding velocity, and gouge thickness in controlling frictional strength and stability of basalt fractures.

Abstract We document the mechanical and geochemical processes of fault rock development in the shallow San Andreas fault (Mojave segment), and quantify their importance in shaping the mineralogy, grain size, fabric, and frictional characteristics of gouge. Through a combination of field and laboratory analysis of an extensive suite of shallow (

Unstable slip of a fault block is considered to be the main cause of shallow earthquakes. However, the underlying mechanism of the stability-to-instability transition of faults has not been fully understood. Here, we used the stiffness ratio, which is the ratio between the shear stiffness of the fault subjected to direct shear and the critical stiffness to evaluate the fault stability degree from stable to unstable slip, and examined the effects of normal stress, roughness, and slip displacement on the fault stability. Our experimental results show that with the increase in slip displacement, the shear stiffness change in stable slip mainly includes four stages, namely “rapid increase–keep unchanged–slow increase–rapid decrease”, and unstable slip tends to occur in the last two stages. This process of shear stiffness change is accelerated by the increase in normal stress and the decrease in fault roughness. Our study reveals that fault stability over slip is mutually dictated by asperity interlocking and wear-induced gouge. Asperity interlocking controls fault stability when the gouge amount is low, whereas the fault gouge prevails with the increased wear of the fault surface since the gouge generated during slip can participate in the subsequent friction process. Thus, we infer that the stable–unstable transition of fault over slip is a spontaneous process due to the interplay of asperity interlocking and wear-induced gouge lubrication.

The industry of metatuff axes and adzes on the western coast of Onega Lake (Eneolithic period, ca. 3500 – 1500 cal. BC) allows assuming some sort of craft specialization. Excavations of a workshop site Fofanovo XIII, conducted in 2010-2011, provided an extremely large assemblage of artefacts (over 350000 finds from just 30 m2, mostly production debitage). An attempt to estimate the output of production within the excavated area is based on experimental data from a series of replication experiments. Mass-analysis with the aid of image recognition software was used to obtain raw data from flakes from excavations and experiments. Statistical evaluation assures that the experimental results can be used as a basement for calculations. According to the proposed estimation, some 500 – 1000 tools could have been produced here, and this can be qualified as an evidence of “mass-production”.

The influence of mechanical damage of the gas transmission pipelines on safe pipelines operation was researched in the article. The paper presents the main pipelines damage types with actual parameters and influence on operational parameters. The main pipeline Kaunas – Kaliningrad part, which was removed as no longer usable, was analysed. This damaged part was removed and changed to a new part by a responsible company. The hardness measurement and micro hardness measurement, chemical analysis, impact strength test, metallography analysis with an optical microscope were used in experiments. The analysed pipeline part was also regenerated by the computer software ANSYS, which works by the finite elements method. Santrauka Straipsnyje nagrinėjama magistralinių dujotiekių mechaninių pažeidimų įtaka saugiam jų eksploatavimui. Darbe pateikti pagrindiniai vamzdynų pažeidimo tipai su jiems būdingais bruožais ir įtaka eksploataciniams parametrams. Ištirta magistralinio dujotiekio Kaunas – Kaliningradas dalis, kuri buvo pašalinta, kaip nebetinkama naudojimui. Tyrimams pasitelktas kietumo ir mikrokietumo matavimas, cheminės analizės tyrimas, smūginio tąsumo bandymas. Mikrostruktūros tyrimams naudotas optinis mikroskopas. Tiriamasis objektas buvo atkurtas kompiuterinės programos, veikiančios baigtinių elementų metodu, ANSYS erdvėje. Raktiniai žodžiai: defektas, dujotiekis, įlenkimas, išskaptavimas, liekamasis resursas, mechaniniai pažeidimai, vamzdynas.