Search

Due to the complex physical and chemical interactions taking place in the sonicated medium, various methods have been proposed in the literature for a better understanding of the sonochemical system. In the present paper, the performance of calorimetry, iodometry, Fricke, 4-nitrophenol, H 2 O 2 , and ascorbic acid dosimetry techniques have been evaluated over the electric power range from 20 to 80 W (f = 300 kHz). These methods have been analyzed for distilled and seawater in light of the literature findings. It has been found that the lowest temperatures and calorimetric energies were obtained for seawater in comparison to distilled water. However, the discrepancy between both mediums disappears with the increase in the electric power up to 80 W. Compared to the calorimetry results, a similar trend was obtained for the KI dosimetry, where the discrepancy between both solutions (seawater and distilled water) increased with the reduction in the electric power down to 20 W. In contrast, over the whole range of the electric power (20-80 W), the H 2 O 2 dosimetry was drastically influenced by the salt composition of seawater, where, I 3 - formation was clearly reduced in comparison to the case of the distilled water. On the other hand, a fluctuated behavior was observed for the Fricke and 4-nitrophenol dosimetry methods, especially at the low electric powers (20 and 40 W). It has been found that dosimetry techniques based on ascorbic acid or potassium iodide are the best means for accurate quantification of the sonochemical activity in the irradiated liquid. As a result, it has been concluded, in terms of the dosimetry process's performance, that the dosimetry methods are in the following order: Ascorbic acid ≈ KI > Fricke > 4-nitrophenol > H 2 O 2 ., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 The Author(s). Published by Elsevier B.V. All rights reserved.)

As an alternative to a water-based cooling system for a sonoreactor, the present work presents for the first time the use of a phase change material for the management and storage of the dissipated heat within the sonicated water. The performance of the PCM is analyzed as a function of liquid height (LH = 5.1, 10.2, 15.3, and 20.4 cm) at a frequency of 300 kHz and two electric powers (P E  = 20 and 60 W). The effective powers dissipated in the irradiated water were determined by the calorimetric technique. A computational fluid dynamics (CFD) model (implemented in ANSYS Fluent® software), was used for the analysis of the combined system (sonoreactor + PCM-thermal unit) at different operating conditions (liquid height and electric power). By analyzing the different outputs (variation of temperature, velocity, enthalpy, liquid fraction of PCM) of the used CFD model, more clarifications are provided about the behaviour of the combined system (sonoreactor + PCM-thermal unit) as function of the liquid height (5.1-20.4 cm) and electric power (20 and 60 W). In terms of temperature, velocity, enthalpy and liquid fraction of the PCM, promising results were obtained in spite of the low thermal conductivity of the employed PCM. The best performance of the combined system (sonoreactor and thermal unit) was obtained at the liquid height of 15.3 cm (corresponding to a water volume of 300 mL) with a similar behaviour (evolution of temperature, velocity, enthalpy, and liquid fraction of the PCM) at both electric powers (i.e., 20 and 60 W) with an intensified response at the P E  = 60 W., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 The Authors. Published by Elsevier B.V. All rights reserved.)

An alternative semi-empirical technique is developed to determine the number density of active cavitation bubbles (N) formed in sonicated solutions. This was achieved by relating the acoustic power supplied to the solution (i.e., determined experimentally) to the released heat by a single bubble. The energy dissipation via heat exchange is obtained by an advanced cavitation model accounting for the liquid compressibility and viscosity, the non-equilibrium condensation/evaporation of water vapor, and heat conduction across the bubble wall and heats of chemical reactions resulting within the bubble at the collapse. A good concordance was observed between our results and those found in the literature. It was found that the number of active bubbles increased proportionally with a rise in ultrasound frequency. Additionally, the increase of acoustic intensity increases the number of active bubbles, whatever the sonicated solution's volume. On the other hand, it was observed that the rise of the irradiated solution volume causes the number of active bubbles to be reduced even when the acoustic power is increased. A decrease in acoustic energy accelerates this negative impact., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier B.V. All rights reserved.)