Search

Efficient exciton dissociation at low energy offsets is key to overcoming voltage losses in organic solar cells. In this work, we developed two dimeric acceptors, i-YT and o-YT, by precisely controlling the position of an asymmetric electron-donating linker. It induced the foldamer conformation of i-YT with a para linkage (relative to the dicyano groups), while retaining the unfold conformation for o-YT. This subtle structural modification influenced the molecular assembly properties, enabled near-zero energy offset exciton dissociation and power conversion efficiencies exceeding 18% for i-YT based organic solar cells. Detailed excitonic dynamics further revealed that the linker position critically influences three processes: the formation of delocalized singlet excited states, ultrafast charge transfer (~5 ps) in solid blends, and the suppression of exciton recombination. Additionally, devices based on i-YT demonstrated outstanding long-term stability, retaining over 85% of their initial efficiency after 1,400 hours of continuous illumination. These findings introduce a new class of dimeric acceptors that combine high efficiency with exceptional stability, offering a promising pathway toward low-energy-loss organic photovoltaics., (© 2024 Wiley‐VCH GmbH.)

In this work, we designed two nitrogen-bridged fluorene-based heptacyclic FNT and nonacyclic FNTT ladder-type structures, which were constructed by one-pot palladium-catalyzed Buchwald-Hartwig amination. FNT and FNTT were further end-capped by FIC acceptors to form two FNT-FIC and FNTT-FIC non-fullerene acceptors (NFAs), respectively. The two NFAs exhibit more red-shifted absorption and higher crystallinity compared to those of the corresponding carbon-bridged FCT-FIC and FCTT-FIC counterparts. Grazing incidence wide-angle X-ray scattering (GIWAXS) measurements reveal that the 2-butyloctyl groups on the nitrogen in the convex region of FNT-FIC interdigitate with the dioctyl groups on the fluorene in the concave region of another FNT-FIC, resulting in a lamellar packing structure with a d spacing of 13.27 Å. As a consequence, the PM6:FNT-FIC (1:1 wt %) device achieved a power conversion efficiency (PCE) of only 6.60%, primarily due to the highly crystalline nature of FNT-FIC, which induced significant phase separation between PM6 and FNT-FIC in the blended film. However, FNTT-FIC, featuring 2-butyloctyl groups positioned on the nitrogen within the concave region of its curved skeleton, exhibits improved donor-acceptor miscibility, thereby promoting a more favorable morphology. As a result, the PM6:FNTT-FIC (1:1.2 wt %) device exhibited a higher PCE of 12.15% with an exceptional V oc of 0.96 V. This research demonstrates that placing alkylamino moieties within the concave region of curved A-D-A NFAs leads to a better molecular design.

We present four-dimensional (4D) scanning transmission electron microscopy (STEM) analysis to obtain a high level of detail regarding the nanoscale ordering within largely disordered organic semiconducting polymers. Understanding nanoscale molecular ordering in semiconducting polymers is crucial due to its connection to the materials' important properties. However, acquiring such information in a spatially localized manner has been limited by the lack of a nanoscale experimental probe, weak signal from ordering, and radiation damage to the sample. By collecting nanodiffraction patterns with a high dynamic range pixelated detector, we acquired statistically robust, high signal-to-noise ratio diffraction patterns from semiconducting organic materials, including poly(3-hexylthiophene-2,5-diyl) (P3HT), P3HT/[6,6]-phenyl C61 butyric acid methyl ester, and indacenodithiophene- co -benzothiadiazole (IDTBT), which largely have disordered structures. Real-space images of the ordered domains were reconstructed from the 4D-STEM data set for a variety of scattering vectors and in-plane angles to capture the different molecular stacking distances and their in-plane orientation. These were then analyzed to obtain the average size of the ordered domains within the sample. Such measurements were arranged in a two-dimensional (2D) histogram, which showed a direct relationship between the type and size of molecular ordering. Complementary analyses, such as intensity variance and angular correlation, were applied to obtain ordering and symmetry information. These analyses enabled us to directly characterize the alkyl and π-π stacking of P3HT, as well as the fullerene domains caused by donor segregation in the P3HT sample. Furthermore, the analysis also captured changes in the P3HT domains when the fullerenes are incorporated. Lastly, IDTBT showed a much lesser degree of ordering without much disinclination between the domains within the 2D histogram. The 4D-STEM analysis that we report here unveils new details of molecular ordering that can be used to optimize the properties of this important class of materials.

Top electrodes of organic photovoltaics (OPVs) are usually thermally evaporated in the vacuum, which is non-continuous and time-consuming and has been the bottleneck for the OPV fabrication process. Printable top electrodes that are free of vacuum, high temperature, and solvents will make OPVs more attractive. Low-melting-point alloys (LMPAs) are promising candidates for printable OPV electrodes thanks to the merits of matching work functions, high electron conductivity, high environment stability, and no need for post-treatment. Here, LMPA electrodes are directly deposited on OPVs by simply falling a single LMPA droplet onto the substrate. The LMPA droplet spreads to form a thin film with a smooth interface intimately contacting the substrate. The electrode area can be tailored by adjusting the droplet diameter or the Weber number, which is the ratio of inertia to surface tension. The interface morphology is mainly affected by the contact temperature. The degree of oxidation and charges on the droplet can also influence the electrode area and interface morphology. OPVs with droplet-impacted LMPA electrodes exhibit power conversion efficiencies of up to 16.17%. This work demonstrates the potential of single-droplet impact deposition as a simple method for printing OPV electrodes for scalable manufacturing., (© 2024 Wiley‐VCH GmbH.)

In this study, six different donor-π-acceptor 1 -π-donor-acceptor 2 type random co-polymers containing benzodithiophene as a donor, benzooxadiazole (BO), and thieno[3,4-c]pyrrole-4,6-dione (TPD) as acceptor, have been synthesized and characterized. In addition to the acceptor core ratio at different values, the effect of aromatic bridge structures on the optical, electronic, and photovoltaic properties of six different random co-polymers is investigated by using thiophene and selenophene structures as aromatic bridge units. To investigate how the acceptor unit ratio and replacement of aromatic bridge units impact the structural, electronic, and optical properties of the polymers, density functional theory (DFT) calculations are carried out for the tetramer models. The open-circuit voltage (V OC ), which is strongly correlated with the HOMO levels of the donor material, is enhanced with the increasing ratio of the TPD moiety. On the other hand, the short-circuit current (J SC ), which is associated with the absorption ability of the donor material, is improved by the increasing ratio of BO moiety with the π-bridges. BO moiety dominant selenophene π-bridged co-polymer (P 4 ) showed the best performance with a power conversion efficiency (PCE) of 6.26%, a J SC of 11.44 mA cm 2 , a V OC of 0.80 V, and a fill factor (FF) of 68.81%., (© 2024 The Author(s). Macromolecular Rapid Communications published by Wiley‐VCH GmbH.)

The development of flexible ITO-free devices is crucial for the industrial advancement of organic photovoltaic (OPV) technology. Here, a novel ITO-free device architecture is proposed, and ITO-free OPV devices are realized on glass substrates with performance comparable to that of ITO-based devices. It is also demonstrated that the performance of ITO-free devices on polyethylene terephthalate (PET) substrates is limited due to the higher surface roughness of PET, leading to high voltage losses, low device quantum efficiency, and high device leakage current. To address the issue of high roughness on the PET surface, a polyimide (PI) modification strategy is developed and the PI-modified PET is employed as the substrate to construct flexible ITO-free OPV devices and large-area modules with an active area of up to 16.5 cm 2 . This approach leads to decreased trap-assisted recombination losses, enhanced exciton dissociation efficiency, and a reduced density of pinholes in flexible OPV devices, resulting in improved photovoltaic performance under both strong and weak illumination conditions. The outcomes of this work are expected to advance the industrial development of flexible organic photovoltaic technology., (© 2024 Wiley‐VCH GmbH.)

The energetic driving force for electron transfer must be minimized to realize efficient optoelectronic devices including organic light-emitting diodes (OLEDs) and organic photovoltaics (OPVs). Exploring the dynamics of a charge-transfer (CT) state at an interface leads to a comprehension of the relationship between energetics, electron-transfer efficiency, and device performance. Here, we investigate the electron transfer from the CT state to the triplet excited state (T 1 ) in upconversion OLEDs with 45 material combinations. By analyzing the CT emission and the singlet excited-state emission from triplet-triplet annihilation via the dark T 1 , their energetics and electron-transfer efficiencies are extracted. We demonstrate that the CT→T 1 electron transfer is enhanced by the stronger CT interaction and a minimal energetic driving force (<0.1 eV), which is explained using the Marcus theory with a small reorganization energy of <0.1 eV. Through our analysis, a novel donor-acceptor combination for the OLED is developed and shows an efficient blue emission with an extremely low turn-on voltage of 1.57 V. This work provides a solution to control interfacial CT states for efficient optoelectronic devices without energy loss., (© 2024 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH.)

The solution aggregation structure of conjugated polymers is crucial to the morphology and resultant optoelectronic properties of organic electronics and is of considerable interest in the field. Precise characterizations of the solution aggregation structures of organic photovoltaic (OPV) blends and their temperature-dependent variations remain challenging. In this work, the temperature-dependent solution aggregation structures of three representative high-efficiency OPV blends using small-angle X-ray/neutron scattering are systematically probed. Three cases of solution processing resiliency are elucidated in state-of-the-art OPV blends. The exceptional processing resiliency of high-efficiency PBQx-TF blends can be attributed to the minimal changes in the multiscale solution aggregation structure at elevated temperatures. Importantly, a new parameter, the percentage of acceptors distributed within polymer aggregates (Ф), for the first time in OPV blend solution, establishes a direct correlation between Ф and performance is quantified. The device performance is well correlated with the Kuhn length of the cylinder related to polymer aggregates L 1 at the small scale and the Ф at the large scale. Optimal device performance is achieved with L 1 at ≈30 nm and Ф within the range of 60 ± 5%. This study represents a significant advancement in the aggregation structure research of organic electronics., (© 2024 Wiley‐VCH GmbH.)

In pursuing high stability and power conversion efficiency for organic photovoltaics (OPVs), a sequential deposition (SD) approach to fabricate active layers with p-i-n structures (where p, i, and n represent the electron donor, mixed donor:acceptor, and electron acceptor regions, respectively, distinctively different from the bulk heterojunction (BHJ) structure) has emerged. Here, we present a novel approach that by incorporating two polymer donors, PBDBT-DTBT and PTQ-2F , and one small-molecule acceptor, BTP-3-EH-4Cl , into the active layer with sequential deposition, we formed a device with nanometer-scale twin p-i-n structured active layer. The twin p-i-n PBDBT-DTBT:PTQ-2F/BTP-3-EH-4Cl device involved first depositing a PBDBT-DTBT:PTQ-2F blend under layer and then a BTP-3-EH-4Cl top layer and exhibited an improved power conversion efficiency (PCE) value of 18.6%, as compared to the 16.4% for the control BHJ PBDBT-DTBT:PTQ-2F:BTP-3-EH-4Cl device or 16.6% for the single p-i-n PBDBT-DTBT/BTP-3-EH-4Cl device. The PCE enhancement resulted mainly from the twin p-i-n active layer's multiple nanoscale charge carrier pathways that contributed to an improved fill factor and faster photocurrent generation based on transient absorption studies. The PBDBT-DTBT:PTQ-2F/BTP-3-EH-4Cl film possessed a vertical twin p-i-n morphology that was revealed through secondary ion mass spectrometry and synchrotron grazing-incidence small-angle X-ray scattering analyses. The thermal stability ( T 80 ) at 85 °C of the twin p-i-n PBDBT-DTBT:PTQ-2F/BTP-3-EH-4Cl devices (906 vs 196 h). This approach of providing a twin p-i-n structure in the active layer can lead to substantial enhancements in both the PCE and stability of organic photovoltaics, laying a solid foundation for future commercialization of the organic photovoltaics technology.PBDBT-DTBT/BTP-3-EH-4Cl devices (906 vs 196 h). This approach of providing a twin p-i-n structure in the active layer can lead to substantial enhancements in both the PCE and stability of organic photovoltaics, laying a solid foundation for future commercialization of the organic photovoltaics technology.

Molecular doping is commonly utilized to tune the charge transport properties of organic semiconductors. However, applying this technique to electrically dope inorganic materials like metal oxide semiconductors is challenging due to the limited availability of molecules with suitable energy levels and processing characteristics. Herein, n-type doping of zinc oxide (ZnO) films is demonstrated using 1,3-dimethylimidazolium-2-carboxylate (CO 2 -DMI), a thermally activated organic n-type dopant. Adding CO 2 -DMI into the ZnO precursor solution and processing it atop a predeposited indium oxide (InO x ) layer yield InO x /n-ZnO heterojunctions with increased electron field-effect mobility of 32.6 cm 2 V -1 s -1 compared to 18.5 cm 2 V -1 s -1 for the pristine InO x /ZnO bilayer. The improved electron transport originates from the ZnO's enhanced crystallinity, reduced hydroxyl concentrations, and fewer oxygen vacancy groups upon doping. Applying the optimally doped InO x /n-ZnO heterojunctions as the electron-transporting layers (ETLs) in organic photovoltaics (OPVs) yields cells with improved power conversion efficiency of 19.06%, up from 18.3% for devices with pristine ZnO, and 18.2% for devices featuring the undoped InO x /ZnO ETL. It is shown that the all-around improved OPV performance originates from synergistic effects associated with CO 2 -DMI doping of the thermally grown ZnO, highlighting its potential as an electronic dopant for ZnO and potentially other metal oxides., (© 2024 The Author(s). Advanced Materials published by Wiley‐VCH GmbH.)

Organic dyes that absorb light in the visible to near-infrared region have garnered significant interest, owing to their extensive utility in organic photovoltaics and various biomedical applications. Aza-boron-dipyrromethene (Aza-BODIPY) dyes are a class of chromophores with impressive photophysical properties such as tunable absorption from the visible region towards near infrared (NIR) region, high molar absorptivity, and fluorescence quantum yield. In this review, we discuss the developments in the aza-BODIPYs, related to their synthetic routes, photophysical properties and their applications. Their design strategies, modifications in chemical structures, mode/position of attachment, and their impact on photo-physical properties are reviewed. The potential applications of aza-BODIPY derivatives such as organic solar cells, photodynamic therapy, boron-neutron capture therapy, fluorescence sensors, photo-redox catalysis, photoacoustic probes and optoelectronic devices are explained., (© 2024 Wiley-VCH GmbH.)

Controlling the nanomorphology in bulk heterojunction photoactive blends is crucial for optimizing the performance and stability of organic photovoltaic (OPV) technologies. A promising approach is to alter the drying dynamics and consequently, the nanostructure of the blend film using solvent additives such as 1,8-diiodooctane (DIO). Although this approach is demonstrated extensively for OPV systems incorporating fullerene-based acceptors, it is unclear how solvent additive processing influences the morphology and stability of nonfullerene acceptor (NFA) systems. Here, small angle neutron scattering (SANS) is used to probe the nanomorphology of two model OPV systems processed with DIO: a fullerene-based system (PBDB-T:PC 71 BM) and an NFA-based system (PBDB-T:ITIC). To overcome the low intrinsic neutron scattering length density contrast in polymer:NFA blend films, the synthesis of a deuterated NFA analog (ITIC-d 52 ) is reported. Using SANS, new insights into the nanoscale evolution of fullerene and NFA-based systems are provided by characterizing films immediately after fabrication, after thermal annealing, and after aging for 1 year. It is found that DIO processing influences fullerene and NFA-based systems differently with NFA-based systems characterized by more phase-separated domains. After long-term aging, SANS reveals both systems demonstrate some level of thermodynamic induced domain coarsening., (© 2024 The Authors. Small published by Wiley‐VCH GmbH.)

The meta-stable active layer morphology of organic solar cells (OSCs) is identified as the main cause of the rapid burn-in loss of power conversion efficiency (PCE) during long-term device operation. However, effective strategies to eliminate the associated loss mechanisms from the initial stage of device operation are still lacking, especially for high-efficiency material systems. Herein, the introduction of molecularly engineered dimer acceptors with adjustable thermal transition properties into the active layer of OSCs to serve as supramolecular stabilizers for regulating the thermal transitions and optimizing the crystallization of the absorber composites is reported. By establishing intimate π-π interactions with small-molecule acceptors, these stabilizers can effectively reduce the trap-state density (N t ) in the devices to achieve excellent PCEs over 19%. More importantly, the low N t associated with an initially optimized morphology can be maintained under external stresses to significantly reduce the PCE burn-in loss in devices. This research reveals a judicious approach to improving OPV stability by establishing a comprehensive correlation between material properties, active-layer morphology, and device performance, for developing burn-in-free OSCs., (© 2024 Wiley‐VCH GmbH.)

Simple synthetic routes, high active layer thickness tolerance as well as stable organic solar cells are relentlessly pursued as key enabling traits for the upscaling of organic photovoltaics. Here, the potential to address these issues by tuning donor polymer molecular weight is investigated. Specifically, the focus is on PTQ10, a polymer with low synthetic complexity, with number average molecular weights of 2.4, 6.2, 16.8, 52.9, and 54.4 kDa, in combination with three different non-fullerene acceptors, namely Y6, Y12, and IDIC. Molecular weight, indeed, unlocks a threefold increase in power conversion efficiency for these blends. Importantly, efficiencies above 10% for blade coated devices with thicknesses between 200 and 350 nm for blends incorporating high molecular weight donor are shown. Spectroscopic, GIWAXS and charge carrier mobility data suggest that the strong photocurrent improvement with molecular weight is related to both, improved electronic transport and polymer contribution to exciton generation. Moreover, it is demonstrated that solar cells based on high molecular weight PTQ10 are more thermally stable due to a higher glass transition temperature, thus also improving device stability., (© 2024 The Authors. Small published by Wiley‐VCH GmbH.)

Evaporable indano[60]fullerene ketone (FIDO) was converted to indano[60]fullerene thioketone (FIDS) in high yield by using Lawesson's reagent. Three compounds with different substituents in para position were successfully converted to the corresponding thioketones, showing that the reaction tolerates compounds with electron-donating and electron-withdrawing substituents. Computational studies with density functional theory revealed the unique vibrations of the thioketone group in FIDS. The molecular structure of FIDS was confirmed by single-crystal X-ray analysis. Bulk heterojunction organic solar cells using three evaporable fullerene derivatives (FIDO, FIDS, C 60 ) as electron-acceptors were compared, and the open-circuit voltage with FIDS was 0.16 V higher than that with C 60 ., (Copyright © 2024, Zhai et al.)

Within recent years, there has been an increased interest towards organic photovoltaics (OPVs), especially with their significant device performance reaching beyond 19% since 2022. With these advances in the device performance of laboratory-scaled OPVs, there has also been more attention directed towards using printing and coating methods that are compatible with large-scale fabrication. Though large-area (>100 cm 2 ) OPVs have reached an efficiency of 15%, this is still behind that of laboratory-scale OPVs. There also needs to be more focus on determining strategies for improving the lifetime of OPVs that are suitable for scalable manufacturing, as well as methods for reducing material and manufacturing costs. In this paper, we compare several printing and coating methods that are employed to fabricate OPVs, with the main focus towards the deposition of the active layer. This includes a comparison of performances at laboratory (<1 cm 2 ), small (1-10 cm 2 ), medium (10-100 cm 2 ), and large (>100 cm 2 ) active area fabrications, encompassing devices that use scalable printing and coating methods for only the active layer, as well as "fully printed/coated" devices. The article also compares the research focus of each of the printing and coating techniques and predicts the general direction that scalable and large-scale OPVs will head towards.

Organic-inorganic heterostructures play a pivotal role in modern electronic and optoelectronic applications including photodetectors and field effect transistors, as well as in solar energy conversion such as photoelectrodes of dye-sensitized solar cells, photoelectrochemical cells, and in organic photovoltaics. To a large extent, performance of such devices is controlled by charge transfer dynamics at and across (inner) interfaces, e.g., between a wide band gap semiconductor and molecular sensitizers and/or catalysts. Hence, a detailed understanding of the structure-dynamics-function relationship of such functional interfaces is necessary to rationalize possible performance limitations of these materials and devices on a molecular level. Vibrational sum-frequency generation (VSFG) spectroscopy, as an interface-sensitive spectroscopic technique, allows to obtain chemically specific information from interfaces and combines such chemical insights with ultrafast time resolution, when integrated as a spectroscopic probe into a pump-probe scheme. Thus, this minireview discusses the advantages and potential of VSFG spectroscopy for investigating interfacial charge transfer dynamics and structural changes at inner interfaces. A critical perspective of the unique spectroscopic view of otherwise inaccessible interfaces is presented, which we hope opens new opportunities for an improved understanding of function-determining processes in complex materials, and brings together communities who are devoted to designing materials and devices with spectroscopists., (© 2024 The Authors. Angewandte Chemie International Edition published by Wiley-VCH GmbH.)

The A 2 -A 1 -D-A 1 -A 2 -type molecules consist of one electron-donating (D) core flanked by two electron-accepting units (A 1 and A 2 ) and have emerged as an essential branch of nonfullerene acceptors (NFAs). These molecules generally possess higher molecular energy levels and wider optical bandgaps compared with those of the classic A-D-A- and A-DA'D-A-type NFAs, owing to the attenuated intramolecular charge transfer effect. These characteristics make them compelling choices for the fabrication of high-voltage organic photovoltaics (OPVs), ternary OPVs, and indoor OPVs. Herein, the recent progress in the A 2 -A 1 -D-A 1 -A 2 -type NFAs are reviewed, including the molecular engineering, structure-property relationships, voltage loss (V loss ), device stability, and photovoltaic performance of binary, ternary, and indoor OPVs. Finally, the challenges and provided prospects are discussed for the further development of this type of NFAs., (© 2023 Wiley‐VCH GmbH.)

While multi-junction geometries have the potential to boost the efficiency of organic solar cells, the experimental gains yet obtained are still very modest. This work proposes an alternative spectral splitting device concept in which various individual semiconducting junctions with cascading bandgaps are laid side by side, thus the name RAINBOW. Each lateral sub-cell receives a fraction of the spectrum that closely matches the main absorption band of the given semiconductor. Here, simulations are used to identify the important material and device properties of each RAINBOW sub-cell. Using the resulting design rules, three systems are selected, with narrow, medium, and wide effective bandgaps, and their potential as sub-cells in this geometry is experimentally investigated. With the aid of a custom-built setup that generates spectrally spread sunlight on demand, the simulations are experimentally validated, showing that this geometry can lead to a reduction in thermalization losses and an improvement in light harvesting, which results in a relative improvement in efficiency of 46.6% with respect to the best sub-cell. Finally, a working proof-of-concept monolithic device consisting of two sub-cells deposited from solution on the same substrate is fabricated, thus demonstrating the feasibility and the potential of the RAINBOW solar cell concept., (© 2023 The Authors. Advanced Materials published by Wiley‐VCH GmbH.)

Developing efficient organic solar cells (OSCs) with thick active layers is crucial for roll-to-roll printing. However, thicker layers often result in lower efficiency. This study tackles this challenge using a polymer adsorption strategy combined with a layer-by-layer approach. Incorporating insulator polystyrene (PS) into the PM6:L8-BO system creates PM6+PS:L8-BO blends, effectively suppressing trap states and extending exciton diffusion length in the mixed donor domain. Adding insulating polymers with benzene rings to the donor enhances π-π stacking of donors, boosting intermolecular interactions and electron wave function overlap. This results in more orderly molecular stacking, longer exciton lifetimes, and higher diffusion lengths. The promoted long-range exciton diffusion leads to high power conversion efficiencies of 19.05% and 18.15% for PM6+PS:L8-BO blend films with 100 and 300 nm thickness, respectively, as well as a respectable 16.00% for 500 nm. These insights guide material selection for better exciton diffusion, and offer a method for thick-film OSC fabrication, promoting a prosperous future for practical OSC mass production., (© 2024 Wiley‐VCH GmbH.)

In the field of organic photovoltaics (OPVs), significant progress has been made in tailoring molecular structures to enhance the open-circuit voltage and the short-circuit current density. However, there remains a crucial gap in the development of coordinated material design strategies focused on improving the fill factor (FF). Here, we introduce a molecular design strategy that incorporates electrostatic potential fluctuation to design organic photovoltaic materials. By reducing the fluctuation amplitude of IT-4F, we synthesized a new acceptor named ITOC6-4F. When using PBQx-TF as a donor, the ITOC6-4F-based cell shows a markedly low recombination rate constant of 0.66×10 -14  cm 3  s -1 and demonstrates an outstanding FF of 0.816, both of which are new records for binary OPV cells. Also, we find that a small fluctuation amplitude could decrease the energetic disorder of OPV cells, reducing energy loss. Finally, the ITOC6-4F-based cell creates the highest efficiency of 16.0 % among medium-gap OPV cells. Our work holds a vital implication for guiding the design of high-performance OPV materials., (© 2024 Wiley‐VCH GmbH.)

Nonfullerene acceptors (NFAs) have dramatically improved the power conversion efficiency (PCE) of organic photovoltaics (OPV) in recent years; however, their device stability currently remains a bottleneck for further technological progress. Photocatalytic decomposition of nonfullerene acceptor molecules at metal oxide electron transport layer (ETL) interfaces has in several recent reports been demonstrated as one of the main degradation mechanisms for these high-performing OPV devices. While some routes for mitigating such degradation effects have been proposed, e.g., through a second layer integrated on the ETL surface, no clear strategy that complies with device scale-up and application requirements has been presented to date. In this work, it is demonstrated that the development of sputtered titanium oxide layers as ETLs in nonfullerene acceptor based OPV can lead to significantly enhanced device lifetimes. This is achieved by tuning the concentration of defect states at the oxide surface, via the reactive sputtering process, to mitigate the photocatalytic decomposition of NFA molecules at the metal oxide interlayers. Reduced defect state formation at the oxide surface is confirmed through X-ray photoelectron spectroscopy (XPS) studies, while the reduced photocatalytic decomposition of nonfullerene acceptor molecules is confirmed via optical spectroscopy investigations. The PBDB-T:ITIC organic solar cells show power conversion efficiencies of around 10% and significantly enhanced photostability. This is achieved through a reactive sputtering process that is fully scalable and industry compatible.

Organic photovoltaic (OPV) cells have experienced significant development in the last decades after the introduction of nonfullerene acceptor molecules with top power conversion efficiencies reported over 19% and considerable versatility, for example, with application in transparent/semitransparent and flexible photovoltaics. Yet, the optimization of the operational stability continues to be a challenge. This study presents a comprehensive investigation of the use of a conjugated polyelectrolyte polymer (CPE-Na) as a hole layer (HTL) to improve the performance and longevity of OPV cells. Two different fabrication approaches were adopted: integrating CPE-Na with PEDOT:PSS to create a composite HTL and using CPE-Na as a stand-alone bilayer deposited beneath PEDOT:PSS on the ITO substrate. These configurations were compared against a reference device employing PEDOT:PSS alone, as the HTL increased efficiency and fill factor. The instruments with CPE-Na also demonstrated increased stability in the dark and under simulated operational conditions. Device-based PEDOT:PSS as an HTL reached T80 after 2500 h while involving CPE-Na in the device kept at T90 in the same period, evidenced by a reduced degradation rate. Furthermore, the impedance spectroscopy and photoinduced transient methods suggest optimized charge transfer and reduced charge carrier recombination. These findings collectively highlight the potential of CPE-Na as a HTL optimizer material for nonfluorine OPV cells.

Although fullerene derivatives such as [6,6]-phenyl-C 61 /C 71 -butyric acid methyl ester (PC 61 BM/PC 71 BM) have dominated the the photoactive acceptor materials in bulk heterojunction organic solar cells (OSCs) for decades, they have several drawbacks such as weak absorption, limited structural tunability, prone to aggregation, and high costs of production. Constructing non-fullerene small molecules with three-dimensional (3D) molecular geometry is one of the strategies to replace fullerenes in OSCs. In this study, a 3D molecule, contorted hexa-cata-hexabenzocoronene tetra perylenediimide (HBC-4-PDI), was designed and synthesized. HBC-4-PDI shows a wide and strong light absorption in the whole UV-vis region as well as suitable energy levels as an acceptor for OSCs. More importantly, the 3D construction effectively reduced the self-aggregation of c-HBC, leading to an appropriate scale phase separation of the blend film morphology in OSCs. A preliminary power conversion efficiency of 2.70 % with a champion open-circuit voltage of 1.06 V was obtained in OSCs with HBC-4-PDI as the acceptor, which was the highest among the previously reported OSCs based on c-HBC derivatives. The results indicated that HBC-4-PDI may serve as a good non-fullerene acceptor for OSCs., (© 2024 Wiley‐VCH GmbH.)

Thanks to the development of novel electron acceptor materials, the power conversion efficiencies (PCE) of organic photovoltaic (OPV) devices are now approaching 20%. Further improvement of PCE is complicated by the need for a driving force to split strongly bound excitons into free charges, causing voltage losses. This review discusses recent approaches to finding efficient OPV systems with minimal driving force, combining near unity quantum efficiency (maximum short circuit currents) with optimal energy efficiency (maximum open circuit voltages). The authors discuss apparently contradicting results on the amount of exciton binding in recent literature, and approaches to harmonize the findings. A comprehensive view is then presented on motifs providing a driving force for charge separation, namely hybridization at the donor:acceptor interface and polarization effects in the bulk, of which quadrupole moments (electrostatics) play a leading role. Apart from controlling the energies of the involved states, these motifs also control the dynamics of recombination processes, which are essential to avoid voltage and fill factor losses. Importantly, all motifs are shown to depend on both molecular structure and process conditions. The resulting high dimensional search space advocates for high throughput (HT) workflows. The final part of the review presents recent HT studies finding consolidated structure-property relationships in OPV films and devices from various deposition methods, from research to industrial upscaling., (© 2023 The Authors. Advanced Science published by Wiley-VCH GmbH.)

The ternary strategy has been widely applied and recognized to be a valid strategy to enhance the organic photovoltaics' (OPVs) performance. Here, a new fused-ring electron acceptor, BTP-PIO, is designed and synthesized, whose ending groups were replaced by a phthalimide-based group (2-butylcyclopenta[ f ]isoindole-1,3,5,7(2 H ,6 H )-tetraone) from traditional 2-(3-oxo-2,3-dihydro-1 H -inden-1-ylidene)malononitrile. The phthalimide-based ending groups endow BTP-PIO with the highest lowest unoccupied molecular orbital (LUMO) level and wider band gap than those of Y6. The ternary device based on PM6:Y6 with BTP-PIO as a guest electron acceptor achieved an elevated open-circuit voltage ( V OC ) of 0.848 V, a short-circuit current density ( J SC ) of 27.31 mA cm -2 , and a fill factor (FF) of 73.9%, generating a remarkable power conversion efficiency (PCE) of 17.10%, which is superior to the PM6:Y6 binary device of 16.08%. The ternary device exhibited improved charge transfer, suppressed carrier recombination, and lower energy loss. BTP-PIO exhibited a good miscibility with Y6, and an alloy phase between BTP-PIO and Y6 was formed in the ternary bulk heterojunction, leading to better phase separation and molecular packing. This research reveals that ending group modification of Y6 derivatives is a feasible way to produce highly efficient ternary devices.

Although recent dramatic advances in power conversion efficiencies (PCEs) have resulted in values over 19%, the poor photostability of organic photovoltaics (OPVs) has been a serious bottleneck to their commercialization. The photocatalytic effect, which is caused by incident ultraviolet-A (UV-A, 320-400 nm) light in the most commonly used zinc oxide (ZnO X ) electron transport layer (ETL), significantly deteriorates the photostability of OPVs. In this work, we develop a new and facile method to enhance the photostability of nonfullerene acceptor-based OPVs by introducing UV-A-insensitive titanium suboxide (TiO X ) ETL. Through an in-depth analysis of mass information at the interface between the ETL and photoactive layer, we confirm that the UV-A-insensitive TiO X suppresses the photocatalytic effect. The resulting device employing the TiO X ETL shows excellent photostability, obtaining 80% of the initial PCE for up to 200 h under 1 sun illumination, which is 10 times longer than that of the conventional ZnO X system (19 h).

Thiazole, as a family of five-membered heteroaromatic rings, is an interesting building unit that can play a role in coplanarizing the backbone as well as deepening the HOMO energy level, which is beneficial for the design of π-conjugated polymers for the photoactive materials in organic photovoltaics (OPVs). Here, we designed and synthesized π-conjugated polymers with simple chemical structures, which consist of 2,2'-bithiazole or 5,5'-bithiazole and alkylthiophenes as the polymer backbone. In fact, the polymers can be easily synthesized in much fewer steps compared to the typical high-performance polymers based on fused heteroaromatic rings. Interestingly, PTN5 exhibited a markedly higher ordered structure than PTN2 . This was likely ascribed to the more coplanar and rigid backbone of PTN5 than that of PTN2 originating in the effectively arranged S···N interaction. As a result, the nonfullerene photovoltaic cell based on PTN5 showed a PCE of 12.2%, which was much higher than the cell based on PTN2 (4.3%) and was high for the polymers consisting of only nonfused rings. These results demonstrate that thiazole-based polymers are promising photoactive materials for OPVs and emphasize the importance of careful molecular design utilizing noncovalent interactions.

Large areas and simple processing methods are necessary for the commercialization of organic photovoltaics (OPVs). However, the efficiency drop due to the variation in thickness of OPVs limits their large-scale applications. Regioregular polymers with good crystallinity and packing properties that exhibit high charge mobility and extraction ability can help overcome these limitations. In this study, a regioregular polymer named PDBD-2FBT was synthesized. The crystallinity and packing properties of PDBD-2FBT were enhanced by a simple thermal treatment. Using PDBD-2FBT material as a donor and Y6-HU as an acceptor, we fabricated binary blend OPV devices. The devices with optimized active layer thickness achieved a power conversion efficiency (PCE) of 14.14%. A PCE of 13.18% was maintained even in thick-film conditions (400 nm), and thickness tolerance was observed. Based on the thickness tolerance, a 5-line module measuring 36 cm 2 was fabricated via the bar-coating method, and a PCE of approximately 10% was achieved.

The short exciton diffusion length in organic semiconductors results in a strong dependence of the conversion efficiency of organic photovoltaic (OPV) cells on the morphology of the donor-acceptor bulk-heterojunction blend. Strong light-matter coupling provides a way to circumvent this dependence by combining the favorable properties of light and matter via the formation of hybrid exciton-polaritons. By strongly coupling excitons in P3HT-C 60 OPV cells to Fabry-Perot optical cavity modes, exciton-polaritons are formed with increased propagation lengths. We exploit these exciton-polaritons to enhance the internal quantum efficiency of the cells, determined from the external quantum efficiency and the absorptance. Additionally, we find a consistent decrease in the Urbach energy for the strongly coupled cells, which indicates the reduction of energetic disorder due to the delocalization of exciton-polaritons in the optical cavity., Competing Interests: Conflict of interest: Authors state no conflicts of interest., (© 2023 the author(s), published by De Gruyter, Berlin/Boston.)

Organic photovoltaics (OPV) present a promising thin-film solar cell technology with particular benefits in terms of weight, aesthetics, transparency, and cost. However, despite being studied intensively since the mid 90's, OPV has not entered the mass consumer market yet. Although the efficiency gap with other thin-film photovoltaics has largely been overcome, active layer stability and performance reproducibility issues have not been fully resolved. State-of-the-art OPV devices employ a physical mixture of electron donor and acceptor molecules in a bulk heterojunction active layer. These blends are prone to morphological changes, leading to performance losses over time. On the other hand, in "single-component" organic solar cells, the donor and acceptor constituents are chemically connected within a single material, preventing demixing and thereby enhancing device stability. Novel single-component materials affording reasonably high solar cell efficiencies and improved lifetimes have recently emerged. In particular, the combination of donor and acceptor structures in conjugated block copolymers (CBCs) presents an exciting approach. Nevertheless, the current CBCs are poorly defined from a structural point of view, while synthetic protocols remain unoptimized. More controlled synthesis followed by proper structural analysis of CBCs is, however, essential to develop rational structure-property-device relations and to drive the field forward. In this perspective, we provide a short overview of the state-of-the-art in single-component organic solar cells prepared from CBCs, reflect on their troublesome characterization and the importance of chemical precision in these structures, give some recommendations, and discuss the potential impact of these aspects on the field., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest., (Copyright © 2023 Theunissen, Smeets and Maes.)

The implementation of sputter-deposited TiO x as an electron transport layer in nonfullerene acceptor-based organic photovoltaics has been shown to significantly increase the long-term stability of devices compared to conventional solution-processed ZnO due to a decreased photocatalytic activity of the sputtered TiO x . In this work, we utilize synchrotron-based photoemission and absorption spectroscopies to investigate the interface between the electron transport layer, TiO x prepared by magnetron sputtering, and the nonfullerene acceptor, ITIC, prepared in situ by spray deposition to study the electronic state interplay and defect states at this interface. This is used to unveil the mechanisms behind the decreased photocatalytic activity of the sputter-deposited TiO x and thus also the increased stability of the organic solar cell devices. The results have been compared to similar measurements on anatase TiO x since anatase TiO x is known to have a strong photocatalytic activity. We show that the deposition of ITIC on top of the sputter-deposited TiO x results in an oxidation of Ti 3+ species in the TiO x and leads to the emergence of a new O 1s peak that can be attributed to the oxygen in ITIC. In addition, increasing the thickness of ITIC on TiO x leads to a shift in the O 1s and C 1s core levels toward higher binding energies, which is consistent with electron transfer at the interface. Resonant photoemission at the Ti L-edge shows that oxygen vacancies in sputtered TiO x lie mostly in the surface region, which contrasts the anatase TiO x where an equal distribution between surface and subsurface oxygen vacancies is observed. Furthermore, it is shown that the subsurface oxygen vacancies in sputtered TiO x are strongly reduced after ITIC deposition, which can reduce the photocatalytic activity of the oxide, while the oxygen vacancies in model anatase TiO x are not affected upon ITIC deposition. This difference can explain the inferior photocatalytic activity of the sputter-deposited TiO x and thus also the increased stability of devices with sputter-deposited TiO x used as an electron transport layer.

As a novel class of materials, D-A conjugated macrocycles hold significant promise for chemical science. However, their potential in photovoltaic remains largely untapped due to the complexity of introducing multiple donor and acceptor moieties into the design and synthesis of cyclic π-conjugated molecules. Here, we report a multiple D-A ring-like conjugated molecule (RCM) via the coupling of dimer molecule DBTP-C3 as a template and thiophenes in high yields. RCM exhibits a narrow optical gap (1.33 eV) and excellent thermal stability, and shows a remarkable photoluminescence yield (Φ PL ) of 11.1 % in solution, much higher than non-cyclic analogues. Organic solar cell (OSC) constructed with RCM as electron acceptor shows efficient charge separation at donor-acceptor band offsets and achieves a power conversion efficiency (PCE) of 14.2 %-approximately fourfold higher than macrocycle-based OSCs reported so far. This is partly due to low non-radiative voltage loss down to 0.20 eV and a high electroluminescence yield (Φ EL ) of 4×10 -4 . Our findings emphasize the potential of D-A cyclic conjugated molecules in advancing organic photovoltaic technology., (© 2023 Wiley-VCH GmbH.)

P-type polymers are polymeric semiconducting materials that conduct holes and have extensive applications in optoelectronics such as organic photovoltaics. Taking the advantage of intrinsic discontinuous light absorption of organic semiconductors, semitransparent organic photovoltaics (STOPVs) present compelling opportunities in various potential applications such as building-integrated photovoltaics, agrivoltaics, automobiles, and wearable electronics. The characteristics of p-type polymers, including optical, electronic, and morphological properties, determine the performance of STOPVs, and the requirements for p-type polymers differ between opaque organic photovoltaics and STOPVs. Hence, in this Minireview, recent advances of p-type polymers used in STOPVs are systematically summarized, with emphasis on the effects of chemical structures, conformation structures, and aggregation structures of p-type polymers on the performance of STOPVs. Furthermore, new design concepts and guidelines are also proposed for p-type polymers to facilitate the future development of high-performance STOPVs., (© 2023 Wiley-VCH GmbH.)

Currently, most of the disclosed ternary strategies to improve photovoltaic performance of all-polymer solar cells (all-PSCs) commonly focus on the guest polymers having similar structures with the host polymer donors or acceptors. Herein, this work develops a distinctive ternary method that adding an amorphous B←N embedded polymer named BN-Cl-2fT to a crystallized host polymer blend of PM6 (a commercialized polymer donor) and PY-TT (a copolymer of Y6 and thieno[3,2-b]thiophene). Although the structures between BN-Cl-2fT and PM6 and PY-TT are completely different, excellent miscibility is found between BN-Cl-2fT and both of the host PM6 and PY-TT, which can be interpreted by the crowded phenyl groups anchoring along the backbone of BN-Cl-2fT, leading to weak self-aggregation. Glazing incidence wide-angle X-ray diffraction (GIWAXS) measurements explicitly confirm the crystallization of PM6 and PY-TT and amorphous feature of BN-Cl-2fT. Furthermore, adding 10 wt% BN-Cl-2fT to PM6:PY-TT can significantly enhance the crystallization of the host polymers. Thus the ternary devices based on PM6:PY-TT:BN-Cl-2fT afford promote short-circuit current density (J SC , 23.29 vs. 21.80 mA cm -2 ), fill factor (FF, 62.4% vs. 60.0%), and power conversion efficiency (PCE, 13.70% vs. 12.23%) in contrast to these parameters of binary devices based on PM6:PY-TT. This work provides a unique and enlightening avenue to design high performance all-PSCs by adding amorphous B←N embedded polymers as guest component to enhance host-crystallization., (© 2023 Wiley-VCH GmbH.)

While organic photovoltaics are accessing specific application sectors taking advantage of their unique properties, it is important to identify as many differentiators as possible to expand the market penetration and consolidation of this technology. In this work, for the first time, the large-scale fabrication of organic photovoltaic modules embedded into structural plastic parts through industrial injection molding is demonstrated. Thermoplastic polyurethane is chosen as the injected material to show that this additional processing step can yield flexible, lightweight photovoltaic modules with enhanced device robustness and virtually unchanged performance. The critical optomechanical and physico-chemical material properties, as well as the plastic processing parameters to enable in-mold plastic solar cells with improved performance and stability, are discussed and provided with perspective., (© 2023 The Authors. Advanced Science published by Wiley-VCH GmbH.)

Surface modification of indium tin oxide (ITO) electrodes with organic molecules is known to tune their work function which results in higher charge carrier selectivity in corresponding organic electronic devices and hence influences the performance of organic solar cells. In recent years, N-heterocyclic carbenes (NHCs) have also been proven to be capable to modify the work function of metals and semimetals compared to the unfunctionalized surface via the formation of strong covalent bonds. In this report, we have designed and performed the modification of the ITO surface with NHC by using the zwitterionic bench stable IPr-CO 2 as the NHC precursor, applied via spin coating. Upon modification, the work function of ITO electrodes was reduced significantly which resulted in electron selective contacts in corresponding organic photovoltaic devices. In addition, various characterization techniques and analytical methods are used to elucidate the nature of the bound species and the corresponding binding mechanism of the material to the ITO surface., (© 2023 The Authors. Chemistry - A European Journal published by Wiley-VCH GmbH.)

Herein, we report on the design, synthesis, physical and chemical properties, and organic photovoltaic (OPV) device performance of four new cathode interlayer (CIL) materials based on bay N-annulated perylene diimides. Starting from the previously reported N-annulated perylene diimide (PDIN-H), the N-position was functionalized with a benzyl and pentafluorobenzyl group to make PDIN-B and PDIN-FB, respectively. Similarly, starting from the previously reported cyanated N-annulated perylene diimide (CN-PDIN-H), the N-position was functionalized with a benzyl and pentafluorobenzyl group to make CN-PDIN-B and CN-PDIN-FB, respectively. The materials exhibit solubility in the green solvent, ethyl acetate, and thus were processed into thin films using ethyl acetate as the solvent. The optoelectronic properties were assessed for both solution and film, and the electrochemical properties were probed in solution. To validate the potential as electron transporting layers, each film was used in conventional OPVs as the CIL with processing from ethyl acetate, while using a bulk heterojunction (BHJ) comprised of PM6:Y6. High power conversion efficiencies (PCEs) of 13% were achieved compared to control devices using the standard PFN-Br CIL., (Copyright © 2023, Wolfe et al.)

Organic solar cells have been continuously studied and developed through the last decades. A major step in their development was the introduction of fused-ring non-fullerene electron acceptors. Yet, beside their high efficiency, they suffer from complex synthesis and stability issues. Perylene-based non-fullerene acceptors, in contrast, can be prepared in only a few steps and display good photochemical and thermal stability. Herein, we introduce four monomeric perylene diimide acceptors obtained in a three-step synthesis. In these molecules, the semimetals silicon and germanium were added in the bay position, on one or both sides of the molecules, resulting in asymmetric and symmetric compounds with a red-shifted absorption compared to unsubstituted perylene diimide. Introducing two germanium atoms improved the crystallinity and charge carrier mobility in the blend with the conjugated polymer PM6. In addition, charge carrier separation is significantly influenced by the high crystallinity of this blend, as shown by transient absorption spectroscopy. As a result, the solar cells reached a power conversion efficiency of 5.38 %, which is one of the highest efficiencies of monomeric perylene diimide-based solar cells recorded to date., (© 2023 The Authors. Chemistry - A European Journal published by Wiley-VCH GmbH.)

The morphological, spectroscopic and rheological properties of silver nanoparticles (AgNPs) synthesized in situ within commercial PEDOT:PSS formulations, labeled PP@NPs, were systematically investigated by varying different synthetic parameters (NaBH 4 /AgNO 3 molar ratio, PEDOT:PSS formulation and silver and PEDOT:PSS concentration in the reaction medium), revealing that only the reagent ratio affected the properties of the resulting nanoparticles. Combining the results obtained from the field-emission scanning electron microscopy analysis and UV-Vis characterization, it could be assumed that PP@NPs' stabilization occurs by means of PSS chains, preferably outside of the PEDOT:PSS domains with low silver content. Conversely, with high silver content, the particles also formed in PEDOT-rich domains with the consequent perturbation of the polaron absorption features of the conjugated polymer. Atomic force microscopy was used to characterize the films deposited on glass from the particle-containing PEDOT:PSS suspensions. The film with an optimized morphology, obtained from the suspension sample characterized by the lowest silver and NaBH 4 content, was used to fabricate a very initial prototype of a water-processable anode in a solar cell prepared with an active layer constituted by the benchmark blend poly(3-hexylthiophene) and [6,6]-Phenyl C61 butyric acid methyl ester (PC 60 BM) and a low-temperature, not-evaporated cathode (Field's metal).

The power conversion efficiencies (PCEs) of organic solar cells (OSCs) have risen dramatically since the introduction of the "Y-series" of non-fullerene acceptors. However, the demonstration of rapid scalable deposition techniques to deposit such systems is rare. Here, for the first time, we demonstrate the deposition of a Y-series-based system using ultrasonic spray coating─a technique with the potential for significantly faster deposition speeds than most traditional meniscus-based methods. Through the use of an air-knife to rapidly remove the casting solvent, we can overcome film reticulation, allowing the drying dynamics to be controlled without the use of solvent additives, heating the substrate, or heating the casting solution. The air-knife also facilitates the use of a non-halogenated, low-toxicity solvent, resulting in industrially relevant, spray-coated PM6:DTY6 devices with PCEs of up to 14.1%. We also highlight the obstacles for scalable coating of Y-series-based solar cells, in particular the influence of slower drying times on blend morphology and crystallinity. This work demonstrates the compatibility of ultrasonic spray coating, and use of an air-knife, with high-speed, roll-to-roll OSC manufacturing techniques.

Developing transparent conductors to replace indium tin oxide (ITO) is a critical objective in the field of organic optoelectronics. Non-atomically doped (NAD) ZnO thin films, while currently exhibiting limited conductivity, are highly promising candidates due to their unique advantages, such as having complete transparency in both the visible and near-infrared spectral regions, solution processability, and the desired surface electronic properties. In this work, the impact of surface modification by insulating polymers on the ultraviolet-enhanced conductivity of NAD-ZnO films is investigated. It was found that polymer modifiers that are rich in amino and hydroxyl groups are effective at increasing the concentration of oxygen vacancies and the conductivity of NAD-ZnO films. The highest conductivity of over 1000 S cm -1 , which is more than twice as high as the previous record for NAD-ZnO films, is achieved using polyethylenimine ethoxylated (PEIE) to modify NAD-ZnO films. Subsequently, the replacement of ITO in organic photovoltaic devices by a ZnO/PEIE electrode is realized. The ZnO/PEIE-based OPV devices that were created exhibit performances comparable to those of ITO-based devices under simulated solar illumination and performances better than those achieved with ITO-based devices under simulated indoor illumination. These results make NAD-ZnO a promising candidate for the widespread replacement of ITO in optoelectronic devices.

Aiming to improve the environmental stability of organic photovoltaics, a multilayered SiO x C y /a-SiN x (O):H composite barrier film coated with a hydrophobic perfluoro copolymer stop layer for polymer:non-fullerene solar cells is developed. The composite film is prepared by spin-coating of polysilicone and perhydropolysilazane (PHPS) following a densification process by vacuum ultraviolet irradiation in an inert atmosphere. The transformation of polysilicone and PHPS to SiO x C y and a-SiN x (O):H is confirmed by Fourier transform infrared and energy-dispersive X-ray spectroscopy measurement. However, the as-prepared PHPS-derived silicon nitride (PDSN) can react with moisture in the ambient atmosphere, yielding microscale defects and a consequent poor barrier performance. Treating the incomplete PDSN with methanol vapor significantly densifies the film yielding low water vapor transmission rates (WVTRs)of 5.0 × 10 -1 and 2.0 × 10 -1 g m -2  d -1 for the one- and three-couple of SiO x C y /a-SiN x (O):H (CON) composite films, respectively. By incorporating a thin hydrophobic perfluoro copolymer layer, the three-coupled methanol-treated CON film with a total thickness of 600 nm shows an extremely low WVTR of 8.7 × 10 -4 g m -2  d -1 . No performance decay is measured for the PM6:Y6 and PM6:L8-BO cells after such an encapsulation process. These encapsulated polymer cells show good stability storaged at 25 °C/50% relative humidity, or under simulated extreme rainstorm tests., (© 2023 Wiley-VCH GmbH.)

To investigate the effect of miscibility between conjugated polymers (CPs) and Y6 on bulk-heterojunction (BHJ) type morphology, we propose three different CPs with similar chemical structures but different miscibility with Y6. After selectively removing Y6 from the CP/Y6 blend films, their interface morphology and interlocked dimensions are quantitatively compared using a square-wave model. As CP-Y6 miscibility increases, a higher intermixed interface is formed, providing an enlarged CP-Y6 interface area. Conversely, as the miscibility between CP and Y6 decreases, the height and width of the interlocked dimensions formed by phase separation gradually decrease and increase, respectively. Additionally, when the CP-Y6 interface morphology and electrical properties of the corresponding organic photovoltaic (OPV) device are correlated, as the highly intermixed CP-Y6 interface develops, the exciton dissociation efficiency increases owing to the reduced exciton diffusion length to be dissociated, but the bimolecular recombination tends to deteriorate simultaneously. Furthermore, if the miscibility between CP and Y6 is excessive, the formation of a charge transport pathway through phase separation is interrupted, deteriorating the charge transport capability in BHJ-type OPVs. However, it was confirmed that introducing F atoms into the conjugated backbone of CP can reduce the bimolecular recombination, providing ameliorated light-harvesting efficiency.

The highest-efficiency organic photovoltaic (OPV)-based solar cells, made from blends of electron-donating and electron-accepting organic semiconductors, are often characterized by strongly reduced (non-Langevin) bimolecular recombination. Although the origins of the reduced recombination are debated, mechanisms related to the charge-transfer (CT) state and free-carrier encounter dynamics controlled by the size of donor and acceptor domains are proposed as underlying factors. Here, a novel photoluminescence-based probe is reported to accurately quantify the donor-acceptor domain size in OPV blends. Specifically, the domain size is measured in high-efficiency non-fullerene acceptor (NFA) systems and a comparative conventional fullerene system. It is found that the NFA-based blends form larger domains but that the expected reductions in bimolecular recombination attributed to the enhanced domain sizes are too small to account for the observed reduction factors. Further, it is shown that the reduction of bimolecular recombination is correlated to enhanced exciton dynamics within the NFA domains. This indicates that the processes responsible for efficient exciton transport also enable strongly non-Langevin recombination in high-efficiency NFA-based solar cells with low-energy offsets., (© 2023 The Authors. Advanced Materials published by Wiley-VCH GmbH.)

The introduction of nonfullerene acceptors (NFA) facilitated the realization of high-efficiency organic solar cells (OSCs); however, OSCs suffer from relatively large losses in open-circuit voltage ( V OC ) as compared to inorganic or perovskite solar cells. Further enhancement in power conversion efficiency requires an increase in V OC . In this work, we take advantage of the high dipole moment of twisted perylene-diimide (TPDI) as a nonfullerene acceptor (NFA) to enhance the V OC of OSCs. In multiple bulk heterojunction solar cells incorporating TPDI with three polymer donors (PTB7-Th, PM6 and PBDB-T), we observed a V OC enhancement by modifying the cathode with a polyethylenimine (PEIE) interlayer. We show that the dipolar interaction between the TPDI NFA and PEIE─enhanced by the general tendency of TPDI to form J-aggregates─plays a crucial role in reducing nonradiative voltage losses under a constant radiative limit of V OC . This is aided by comparative studies with PM6:Y6 bulk heterojunction solar cells. We hypothesize that incorporating NFAs with significant dipole moments is a feasible approach to improving the V OC of OSCs.

It was recently reported that the most popular electron-accepting units introduced to π-conjugated oligomers studied for organic photovoltaic applications are susceptible to unwanted and even destructive photochemical reactions. The consequences of Z / E photoisomerization of the popular 2-(1,1-dicyanomethylene)rhodanine (RCN) unit on the optical and morphological properties of a homologous series of RCN-functionalized oligothiophenes are studied here. Oligomers consisting of one, two, or three thiophene units were studied as pure Z isomers and with E isomer compositions of 25, 53, and 45%, respectively, for Z / E mixtures. Solutions of Z isomers and Z / E mixtures were characterized by UV-vis and photoluminescence spectroscopy, wherein changes to optical properties were evaluated on the basis of E isomer content. X-ray diffraction of thin-film Z / E mixtures reveals crystalline domains of both Z and E forms after thermal annealing for mono- and bithiophene oligomers, with greater interplanar spacing for E crystalline domains than the Z counterparts along the substrate normal direction. The surface morphology viewed by atomic force microscopy also shows fiberlike structures for the E form with a much larger aspect ratio than for the Z domains in the bithiophene oligomer. Optical characterization reveals drastic changes in the solid state upon introduction of the E form for the mono- and bithiophene derivatives, whereas subtle consequences are noted for the terthiophene analogue. Most notably, a 132 nm redshift in maximum absorption occurs for the bithiophene oligomer films containing 53% E isomer compared to the pure Z counterpart. Finally, although solid-state photoisomerization experiments find no evidence of Z → E isomerization in polycrystalline Z films, E → Z isomerization is observed and becomes more restrictive in films with higher crystallinity (i.e., after thermal annealing). This structure-property study, which elucidates the consequences of the RCN configuration on solid-state packing and optical properties, is expected to guide the development of more efficient and stable organic optoelectronic devices.

It is of vital importance to improve the long-term and photostability of organic photovoltaics, including organic solar cells (OSCs) and organic photodetectors (OPDs), for their ultimate industrialization. Herein, two series of terpolymers featuring with an antioxidant butylated hydroxytoluene (BHT)-terminated side chain, PTzBI-EHp-BTBHTx and N2200-BTBHTx (x = 0.05, 0.1, 0.2), are designed and synthesized. It was found that incorporating appropriate ratio of benzothiadiazole (BT) with BHT side chains on the conjugated backbone would induce negligible effect on the molecular weight, absorption spectra and energy levels of polymers, however, which would obviously enhance the photostability of these polymers. Consequently, all-polymer solar cells (all-PSCs) and photodetectors were fabricated, and the all-PSC based on PTzBI-EHp-BTBHT0.05: N2200 realized an optimal power conversion efficiency (PCE) approaching ~ 10%, outperforming the device based on pristine PTzBI-EHp: N2200. Impressively, the all-PSCs based on BHT-featuring terpolymers displayed alleviated PCEs degradation under continuous irradiation for 300 h due to the improved morphological and photostability of active layers. The OPDs based on BHT-featuring terpolymers achieved a lower dark current at - 0.1 bias, which could be stabilized even after irradiation over 400 h. This study provides a feasible approach to develop terpolymers with antioxidant efficacy for improving the lifetime of OSCs and OPDs., (© 2023. The Author(s).)

Organic photovoltaics (OPVs) have unique advantages of low weight, mechanical flexibility, and solution processability, which make them exceptionally suitable for integrating low-power Internet of Things devices. However, achieving improved operational stability together with solution processes that are applicable to large-scale fabrication remains challenging. Their major limitation arises due to the instable factors that occur both inside the thick active film and from the ambient environment, which cannot be completely resolved via the current encapsulation techniques used for flexible OPVs. Additionally, thin active layers are highly vulnerable to point defects, which result in low yield rates and impede the laboratory-to-industry translation. In this study, flexible fully solution-processed OPVs with improved indoor efficiency and long-term operational stability than that of conventional OPVs with evaporated electrodes are achieved. Benefiting from the oxygen and water vapor permeation barrier of the spontaneously formed gallium oxide layers on the exposed eutectic gallium-indium surface, fast degradation of the OPVs with thick active layers is prevented, maintaining 93% of its initial P max after 5000 min of indoor operation under 1000 lx light-emitting diode (LED) illumination. Additionally, by using the thick active layer, spin-coated silver nanowires could be directly used as bottom electrodes without complicated flattening processes, thereby substantially simplifying the fabrication process and proposing a promising manufacturing technique for devices with high-throughput energy demands.

Silver grid electrodes on glass and flexible plastic substrates with performance that exceeds that of commercial indium-tin oxide (ITO) coated glass are reported and show their suitability as a drop-in replacement for ITO glass in solution-processed organic photovoltaics (OPVs). When supported on flexible plastic substrates these electrodes are stable toward repeated bending through a small radius of curvature over tens of thousands of cycles. The grid electrodes are fabricated by the unconventional approach of condensation coefficient modulation using a perfluorinated polymer shown to be far superior to the other compounds used for this purpose to date. The very narrow line width and small grid pitch that can be achieved also open the door to the possibility of using grid electrodes in OPVs without a conducting poly(3,4-ethylenedioxythiophene-poly(styrenesulfonate) (PEDOT: PSS) layer to span the gaps between grid lines., (© 2023 The Authors. Advanced Materials published by Wiley-VCH GmbH.)