Search

Biodegradable plastics are increasingly utilized in packaging, driven by green chemistry and environmental responsibility. Among them, poly(L-lactic acid) (PLLA) stands out due to its biodegradability and biocompatibility. However, its limited gas permeability and selectivity hinder its application in produce preservation. To address this, polyethylene glycol (PEG), which enhances CO 2 selectivity, and polydimethylsiloxane (PDMS), known for its large free volume and high gas diffusion coefficients, were incorporated into PLLA to synthesize two triblock copolymers, PL-E-LA and PL-D-LA. Films with varying block ratios were prepared via solution casting. The results showed that elongation at break for PL-E-LA and PL-D-LA increased by 2.5-fold and 8.7-fold, respectively, while their crystallization temperatures (T cc ) decreased to 79.4 °C and 108.3 °C. Scanning electron microscopy (SEM) revealed spherical phase separation in PL-D-LA and finger-like structures in PL-E-LA. By blending these copolymers, gas permeability and the CO 2 /O 2 permeability ratio were optimized. At 5 °C, the CO 2 /O 2 permeability ratio of PL(D 25 /E 75 )LA films reached 9.1, meeting the ideal range (8-10:1) for fresh produce packaging. Atomic force microscopy (AFM) confirmed the PL(D 25 /E 75 )LA film exhibited the lowest surface height (52 nm) and roughness (Ra = 4.051), with a fine, uniform phase separation that facilitated gas diffusion and optimized permeability. The application of PL(D 25 /E 75 )LA to Chinese bayberry preservation effectively reduced weight loss, delayed firmness degradation, and maintained quality attributes such as color, sugar, and acid content, demonstrating its superior preservation performance. This study highlights the potential of PLLA-based packaging materials with optimized phase separation for produce storage and transportation., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interest or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2025 Elsevier B.V. All rights reserved.)

Grapes were packaged by different Poly (L-lactic acid)-based packaging films (PLTL-PLEL) and stored at 5 °C for 35 days to investigate the effects of equilibrium modified atmosphere packaging on the quality of "Kyoho" grapes during storage. Changes in physiochemical quality, antioxidant content and senescence of grapes were studied. Furthermore, UPLC-Q-TOF-MS/MS was used to observe and identify key factors influencing the variation of grape anthocyanins under different atmosphere conditions. Alterations in gas components and enzyme activities significantly impacted anthocyanin levels, highlighting oxygen concentration as the primary influence on total anthocyanin levels. The PLTL-PLEL50 packaging resulted in an approximate 5.7% lower weight loss and increased soluble solids by approximately 14.4%, vitamin C, total phenols and flavonoids reaching 60.2 mg/100 g, 8.4 mg/100 g and 7.2 mg/100 g, respectively. This packaging also preserved higher anthocyanin levels, with malvidin-3-glucoside and peonidin-3-glucoside at 0.55 μg/mL and 1.62 μg/mL, respectively, on the 35th day of storage., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 Elsevier Ltd. All rights reserved.)

Nanofibers have emerged as a highly effective method for drug delivery, attributed to their remarkable porosity and ability to regulate drug release rates while minimizing toxicity and side effects. In this study, we successfully loaded the natural anticancer drugs curcumin (CUR) and hypocrellin A (HA) into pure poly(l-lactic acid) (PLLA) and PLLA-silk protein (PS) composite nanofibers through electrospinning technology. This result was confirmed through comprehensive analysis involving SEM, FTIR, XRD, DSC, TG, zeta potential, and pH stability analysis. The encapsulation efficiency of all samples exceeded 85%, demonstrating the effectiveness of the loading process. Additionally, the drug release doses were significantly higher in the composites compared to pure PLLA, owing to the enhanced crystallinity and stability of the silk proteins. Importantly, the composite nanofibers exhibited excellent pH stability in physiological and acidic environments. Furthermore, the drug-loaded composite nanofibers displayed strong inhibitory effects on cancer cells, with approximately 28% (HA) and 37% (CUR) inhibition of cell growth and differentiation within 72 h, while showing minimal impact on normal cells. This research highlights the potential for controlling drug release through the manipulation of fiber diameter and crystallinity, paving the way for wider applications of electrospun green nanomaterials in the field of medicine.

High costs and low performance have constrained the application of bio-based materials in food packaging. Herein, a series of ultra-thin poly(L-lactic acid-iconic acid N-diol) (P(LA-NI)) copolymer films were developed using a "one-step" polycondensation process with integrated toughness, barrier properties, gas selectivity, and quality control features. The massive branched structure and gg conformers in P(LA-NI) act as "internal chain expansion" and "internal plasticization". Meanwhile, P(LA-NI) contains numerous polar groups and unique nanoscale microphase structures to realize excellent CO 2 , O 2 barrier, CO 2 /O 2 selectivity, anti-fogging, and UV shielding functions. The atmosphere within the package spontaneously achieves the desirable low O 2 and high CO 2 levels when packaging button mushrooms with high respiratory metabolism. Eventually, the shelf life of button mushrooms reached 24 days, >3-fold extended. This PLLA-based film meets "dual carbon" and "food safety" goals and has vast potential for fresh food preservation., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier Ltd.)

Background: Given the significant impact on human health, it is imperative to develop novel treatment approaches for diabetic wounds, which are prevalent and serious complications of diabetes. The diabetic wound microenvironment has a high level of reactive oxygen species (ROS) and an imbalance between proinflammatory and anti-inflammatory cells/factors, which hamper the healing of chronic wounds. This study aimed to develop poly(L-lactic acid) (PLLA) nanofibrous membranes incorporating curcumin and silver nanoparticles (AgNPs), defined as PLLA/C/Ag, for diabetic wound healing., Methods: PLLA/C/Ag were fabricated via an air-jet spinning approach. The membranes underwent preparation and characterization through various techniques including Fourier-transform infrared spectroscopy, measurement of water contact angle, X-ray photoelectron spectroscopy, X-ray diffraction, scanning electron microscopy, assessment of in vitro release of curcumin and Ag + , testing of mechanical strength, flexibility, water absorption and biodegradability. In addition, the antioxidant, antibacterial and anti-inflammatory properties of the membranes were evaluated in vitro , and the ability of the membranes to heal wounds was tested in vivo using diabetic mice., Results: Loose hydrophilic nanofibrous membranes with uniform fibre sizes were prepared through air-jet spinning. The membranes enabled the efficient and sustained release of curcumin. More importantly, antibacterial AgNPs were successfully reduced in situ from AgNO 3 . The incorporation of AgNPs endowed the membrane with superior antibacterial activity, and the bioactivities of curcumin and the AgNPs gave the membrane efficient ROS scavenging and immunomodulatory effects, which protected cells from oxidative damage and reduced inflammation. Further results from animal studies indicated that the PLLA/C/Ag membranes had the most efficient wound healing properties, which were achieved by stimulating angiogenesis and collagen deposition and inhibiting inflammation., Conclusions: In this research, we successfully fabricated PLLA/C/Ag membranes that possess properties of antioxidants, antibacterial agents and anti-inflammatory agents, which can aid in the process of wound healing. Modulating wound inflammation, these new PLLA/C/Ag membranes serve as a novel dressing to enhance the healing of diabetic wounds., Competing Interests: None declared., (© The Author(s) 2024. Published by Oxford University Press.)

Background: Poly(L-lactic acid) (PLLA) is a biodegradable polymer (BP) that replaces conventional petroleum-based polymers.  The hydrophobicity of biodegradable PLLA periodontal barrier membrane in wet state can be solved by alloying it with natural polymers. Alloying PLLA with gelatin imparts wet mechanical properties, hydrophilicity, shrinkage, degradability and biocompatibility to the polymeric matrix., Methods: To investigate membrane performance in the wet state, PLLA/gelatin membranes were synthesized by varying the gelatin concentration from 0 to 80 wt%. The membrane was prepared by electrospinning., Results: At the macroscopic scale, PLLA containing gelatin can tune the wet mechanical properties, hydrophilicity, water uptake capacity (WUC), degradability and biocompatibility of PLLA/gelatin membranes. As the gelatin content increased from 0 to 80 wt%, the dry tensile strength of the membranes increased from 6.4 to 38.9 MPa and the dry strain at break decreased from 1.7 to 0.19. PLLA/gelatin membranes with a gelatin content exceeding 40% showed excellent biocompatibility and hydrophilicity. However, dimensional change (37.5% after 7 days of soaking), poor tensile stress  in wet state (3.48 MPa) and rapid degradation rate (73.7%) were observed. The highest WUC, hydrophilicity, porosity, suitable mechanical properties and biocompatibility were observed for the PLLA/40% gelatin membrane., Conclusion: PLLA/gelatin membranes with gelatin content less than 40% are suitable as barrier membranes for absorbable periodontal tissue regeneration due to their tunable wet mechanical properties, degradability, biocompatibility and lack of dimensional changes., (© 2024. Korean Tissue Engineering and Regenerative Medicine Society.)

The flammability of bio-derived poly(L-lactic acid) (PLA) greatly limits its application and eco-friendly multifunctional fire-fighting PLA-based composites are highly desired. In this work, a fully bio-based modified CS (C-CS) and commercially available eco-friendly ammonium polyphosphate (APP) were used as a synergistic flame retardant agent (C-CS/APP) to investigate its effects on fire-proofing performance and diverse properties of the PLA. The PLA/5%C-CS/5%APP composite exhibited excellent fire-resistant performance with anti-droplet, smoke-suppression and self-extinguishing property, and its limited oxygen index enhanced by 37 % (compared with neat PLA). This composite reached the highest V-0 fire safety rating, and its peak of heat release rate and total smoke production reduced by 26.5 % and 68.3 %, respectively. In addition, the char residue yield after the cone calorimeter test increased by 46 times in the composite, indicating an outstanding char-forming capacity. The condensed phase flame retardancy played a crucial role on the fire-fighting of this composite, that is, significantly enhanced char residue (as a physical barrier) blocked the heat exchange and O 2 entry, and further suppressed the combustion reaction. Additionally, the PLA-based composite showed outstanding UV-absorption property, good anti-bacterial effect, and increased hydrophilicity and crystallizability., Competing Interests: Declaration of competing interest The authors declare no competing financial interest., (Copyright © 2024 Elsevier B.V. All rights reserved.)

Large bone defects, often resulting from trauma and disease, present significant clinical challenges. Electrospun fibrous scaffolds closely resembling the morphology and structure of natural ECM are highly interested in bone tissue engineering. However, the traditional electrospun fibrous scaffold has some limitations, including lacking interconnected macropores and behaving as a 2D scaffold. To address these challenges, a sponge-like electrospun poly(L-lactic acid) (PLLA)/polycaprolactone (PCL) fibrous scaffold has been developed by an innovative and convenient method (i.e., electrospinning, homogenization, progen leaching and shaping). The resulting scaffold exhibited a highly porous structure (overall porosity = 85.9 %) with interconnected, regular macropores, mimicking the natural extracellular matrix. Moreover, the incorporation of bioactive glass (BG) particles improved the hydrophilicity (water contact angle = 79.7°) and biocompatibility and promoted osteoblast cell growth. In-vitro 10-day experiment revealed that the scaffolds led to high cell viability. The increment of the proliferation rates was 195.4 % at day 7 and 281.6 % at day 10. More importantly, Saos-2 cells could grow, proliferate, and infiltrate into the scaffold. Therefore, this 3D PLLA/PCL with BG sponge holds great promise for bone defect repair in tissue engineering applications., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier B.V. All rights reserved.)

Poly(L-lactic acid) (PLA) is an environmentally-friendly bioplastic with high mechanical strength, but suffers from inherent flammability and poor toughness. Many tougheners have been reported for PLA, but their synthesis usually involves organic solvents, and they tend to dramatically reduce the mechanical strength and cannot settle the flammability matter. Herein, we develop strong, tough, and flame-retardant PLA composites by reactive blending PLA, 6-((double (2-hydroxyethyl) amino) methyl) dibenzo [c, e] [1,2] oxyphosphate acid 6-oxide (DHDP) and diphenylmethane diisocyanate (MDI) and define it PLA/xGH, where x indicates that the molar ratio of -NCO group in MDI to -OH group in PLA and DHDP is 1.0x: 1. This fabrication requires no solvents. PLA/2GH with a -NCO/-OH molar ratio of 1.02: 1 maintains high tensile strength of 63.0 MPa and achieves a 23.4 % increase in impact strength compared to PLA due to the incorporation of rigid polyurethane chain segment. The vertical combustion (UL-94) classification and limiting oxygen index (LOI) of PLA/2GH reaches V-0 and 29.8 %, respectively, because DHDP and MDI function in gas and condensed phases. This study displays a generalizable strategy to create flame-retardant bioplastics with great mechanical performances by the in-situ formation of P/N-containing polyurethane segment within PLA., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier B.V. All rights reserved.)

Electrospun fibres have emerged as vital components in developing tissue engineering scaffolds. Calcium phosphate-based materials, renowned for their bioactivity and biocompatibility, have garnered considerable attention in biomedical applications. This study focuses on the incorporation of amorphous calcium phosphate (ACP) nanoparticles into poly(L-lactic acid) (PLLA) to produce electrospun PLLA/ACP fibrous membranes. Subsequent treatment with acetone yielded a hierarchical porous structure, boasting an ultra-high surface area of 94.7753 ± 0.3884 m 2 /g. The ACP nanoparticles, initially encapsulated by PLLA, were exposed on the fibre surface after acetone treatment. Furthermore, the porous PLLA/ACP fibrous membrane exhibited superior mechanical properties (Young's modulus = 0.148 GPa, tensile strength = 3.05 MPa) and enhanced wettability. In a 7-day in vitro cell culture with human osteoblast-like cells, the porous PLLA/ACP fibrous membrane demonstrated a significant improvement in osteoblast adhesion and proliferation, with a proliferation rate increase of 252.0% and 298.7% at day 4 and day 7, respectively. These findings underscore the potential of the porous PLLA/ACP fibrous membrane as a promising candidate for bone tissue scaffolds., Competing Interests: Declaration of competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024 The Authors. Published by Elsevier Ltd.. All rights reserved.)

In high molecular weight poly(L-lactic acid)/poly(D-lactic acid) (HMW PLLA/PDLA) blends, the construction of exclusive stereocomplex crystals (SC) with high crystallinity and strong melt memory remains a great challenge. In the present study, various norbornene dicarboxylate complexes (TMXNa, Mg, Al, or Ca) were employed as the stereo-selective nucleating agents (NAs), and their effect on the crystallization characteristics, rheological behavior, and heat resistance of PLLA/PDLA blends were thoroughly studied. Strikingly, TMX-Al facilitated the construction of exclusive SC with over 50 % crystallinity and excellent melt memory. The dense SC crystals network structure boosted the heat resistance of L/D-xAl blends with a VST as high as 145 °C. The strengthened intermolecular interaction fostered the generation of pre-ordered structure in the melt and enhanced chain interdiffusion, which contributed to intermolecular nucleation and SC crystallization in L/D-xAl blend. This study opens up a new avenue for melt processing and application development of SC-PLA materials., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier B.V.)

Nerve injuries pose a drastic threat to nerve mobility and sensitivity and lead to permanent dysfunction due to low regenerative capacity of mature neurons. The electrical stimuli that can be provided by electroactive materials are some of the most effective tools for the formation of soft tissues, including nerves. Electric output can provide a distinctly favorable bioelectrical microenvironment, which is especially relevant for the nervous system. Piezoelectric biomaterials have attracted attention in the field of neural tissue engineering owing to their biocompatibility and ability to generate piezoelectric surface charges. In this review, an outlook of the most recent achievements in the field of piezoelectric biomaterials is described with an emphasis on piezoelectric polymers for neural tissue engineering. First, general recommendations for the design of an optimal nerve scaffold are discussed. Then, specific mechanisms determining nerve regeneration via piezoelectric stimulation are considered. Activation of piezoelectric responses via natural body movements, ultrasound, and magnetic fillers is also examined. The use of magnetoelectric materials in combination with alternating magnetic fields is thought to be the most promising due to controllable reproducible cyclic deformations and deep tissue permeation by magnetic fields without tissue heating. In vitro and in vivo applications of nerve guidance scaffolds and conduits made of various piezopolymers are reviewed too. Finally, challenges and prospective research directions regarding piezoelectric biomaterials promoting nerve regeneration are discussed. Thus, the most relevant scientific findings and strategies in neural tissue engineering are described here, and this review may serve as a guideline both for researchers and clinicians., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in the paper “Revealing an important role of piezoelectric polymers in nervous-tissue regeneration: a Review” submitted to Materials Today Bio., (© 2024 Published by Elsevier Ltd.)

Improving hydrophobicity through the regulation of surface microstructures has attracted significant interest in various applications. This research successfully prepared a surface with microsphere structures using the Non-solvent induced phase separation method (NIPS). Poly(D-Lactic acid)-block-poly(ethylene glycol)-block-poly(D-Lactic acid) (PDLA-PEG-PDLA) block polymers were synthesized by ring-opening polymerization of D-Lactic acid (D-LA) using polyethylene glycol (PEG) as initiator. PLLA/PDLA-PEG-PDLA membrane with microscale microsphere morphology was fabricated using a nonsolvent-induced self-assembly method by blending the triblock copolymer with a poly(L-lactic acid) (PLLA) solution. In phase separation processes, the amphiphilic block copolymers self-assemble into micellar structures to minimize the Gibbs free energy, and the hydrophilic segments (PEG) aggregate to form the core of the micelles, while the hydrophobic segments (PDLA) are exposed on the outer corona resulting in a core-shell structure. The Stereocomplex Crystalline (SC), formed by the hydrogen bonding between PLLA and PDLA, can facilitate the transition from liquid-liquid phase separation to solid-liquid phase separation, and the PEG chain segments can enhance the formation of SC. The membrane, prepared by adjusting the copolymer content and PEG chain length, exhibited adjustable microsphere quantity, diameter, and surface roughness, enabling excellent hydrophobicity and controlled release of oil-soluble substances., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

In order to expand the application of PLLA in the packaging field, improving its toughness and antibacterial activity has been widely concerned. However, seldom researches can simultaneously efficiently improve the toughness and antibacterial activity of PLLA by adding one kind of additions. To address above problems, the bifunctional branched poly(butylene adipate) ionomer additive (b-PBAUi) was synthesized. For b-PBAUi, its branched structure not only increased the plasticizing effect of additive, but also acted as reaction sites to introduce more antibacterial ionic salt. Due to the special structure of b-PBAUi, PLLA/b-PBAUi blends achieved excellent toughness and antibacterial efficiency. The elongation of blend reached 125 % even by adding 5 wt% b-PBAUi, which was 10 times higher than that of PLLA. From the analysis of phase morphology, it could be found that the microvoids promoting tensile yielding was the main tensile toughening mechanism for PLLA/b-PBAUi blends. In addition, the antibacterial activity of PLLA was significantly improved by adding b-PBAUi. For PLLA/b-PBAUi 10 and PLLA/b-PBAUi 15 , the antibacterial efficiency against E. coli and S. aureus bacteria exceeded 99.0 %. By comprehensive consideration, the optimal blend ratio was achieved by PLLA/b-PBAUi 10 due to its excellent toughness and antibacterial efficiency., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023. Published by Elsevier B.V.)

The effect of poly(L-lactic acid)/poly(ethylene glycol)-poly(L-lactic acid) block film on preservation of Chinese winter jujube (Ziziphus Jujuba Mill.cv.Dongzao) was investigated. Eight arm poly(ethylene glycol)-poly(L-lactic acid) block copolymer (8-PEG/PLLA) and net structure 8-PEG/PLLA (NET-PEL) were successfully synthetized by ring-opening polymerization, and different percentages (5, 10, and 20 %) of them were blended with PLLA to prepared blends films. Mechanical properties, modulated different scanning calorimetry (MDSC), gas and water vapor permeability results showed that 8-PEG/PLLA and NET-PEL block copolymer greatly increased the toughness of blend films, could be decrease PLLA segment glass transition temperature (T g )from 59.5 °C to 41.6-46.7 °C and cold crystallization temperature(T cc )from 89.4 °C to 73.5-77.7 °C, and increased the oxygen (O 2 ), carbon dioxide (CO 2 ), and water vapor transmission rate. The an appropriate gas concentration [O 2 (2.56-3.51 %), CO 2 (5.05-5.56 %)] was created inside the PLLA/NET-PEL20% (NEPEL20)group, which could restrain increase of total soluble solids (TSS), malonaldehyde content. The firmness, color luminosity (L*), total phenols, and ascorbic acid were maintained at higher level，and kept its commercial value after 40 days of storage. The present data indicated that treating post-harvest winter jujubes with NEPEL20 MAP packaging was an effective method for preservation of postharvest winter jujube., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023. Published by Elsevier B.V.)

This review will briefly examine the development of 3D-printed scaffolds for craniofacial bone regeneration. We will, in particular, highlight our work using Poly(L-lactic acid) (PLLA) and collagen-based bio-inks. This paper is a narrative review of the materials used for scaffold fabrication by 3D printing. We have also reviewed two types of scaffolds that we designed and fabricated. Poly(L-lactic acid) (PLLA) scaffolds were printed using fused deposition modelling technology. Collagen-based scaffolds were printed using a bioprinting technique. These scaffolds were tested for their physical properties and biocompatibility. Work in the emerging field of 3D-printed scaffolds for bone repair is briefly reviewed. Our work provides an example of PLLA scaffolds that were successfully 3D-printed with optimal porosity, pore size and fibre thickness. The compressive modulus was similar to, or better than, the trabecular bone of the mandible. PLLA scaffolds generated an electric potential upon cyclic/repeated loading. The crystallinity was reduced during the 3D printing. The hydrolytic degradation was relatively slow. Osteoblast-like cells did not attach to uncoated scaffolds but attached well and proliferated after coating the scaffold with fibrinogen. Collagen-based bio-ink scaffolds were also printed successfully. Osteoclast-like cells adhered, differentiated, and survived well on the scaffold. Efforts are underway to identify means to improve the structural stability of the collagen-based scaffolds, perhaps through mineralization by the polymer-induced liquid precursor process. 3D-printing technology is promising for constructing next-generation bone regeneration scaffolds. We describe our efforts to test PLLA and collagen scaffolds produced by 3D printing. The 3D-printed PLLA scaffolds showed promising properties akin to natural bone. Collagen scaffolds need further work to improve structural integrity. Ideally, such biological scaffolds will be mineralized to produce true bone biomimetics. These scaffolds warrant further investigation for bone regeneration., (© 2023 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.)

We present synthetic experiments of lactic acid (LA) polycondensation to produce poly(lactic acid) (PLA) as well as kinetic modeling calculations that capture the polymer molecular weight increase with time, given the initial concentrations. Tin-octoate-catalyzed polycondensation of (D,L)- or L-lactic acid was carried out in pre-dried toluene after azeotropic dehydration for 48-120 h at 130-137 °C. The polymerization was optimized by varying lactic acid and catalyst concentrations as well as the temperature. Gel permeation chromatography was used to experimentally follow the evolution of molecular weights and the products were characterized by NMR, TGA, DSC and IR. Under optimal conditions, PLLA with weight-average molecular weight ( M w ) of 161 kDa could be obtained. The rate equations that describe polycondensation kinetics were recast in a condensed form that allowed very fast numerical solution and calculation of the number-average molecular weight with time. Deviations with respect to the experiment were minimized in a least-squares fashion to determine rate constants. The optimized kinetics parameters are shown to reproduce the experimental data accurately.

The design of functional micro or nanostructured surfaces is undergoing extensive research for their intriguing multifunctional properties and for large variety of potential applications in biomedical field (tissue engineering or cell adhesion), electronics, optics or microfluidics. Such nanosized topographies can be easily fabricated by various lithography techniques and can be also further reinforced by synergic effect by combining aforementioned structures along materials with already outstanding antibacterial properties. In this work we fabricated novel micro/nanostructured substrates using soft lithography replication method and subsequent thermal nanoimprint lithography method, creating nanostructured films based on poly (l-lactic acid) (PLLA) fortified by thin silver films deposited by PVD. Main nanoscale patterns were fabricated by replicating surface patterns of optical discs (CDs and DVDs), which proved to be easy, fast and inexpensive method for creating relatively large area patterned surfaces. Their antimicrobial activity was examined in vitro against the bacteria Escherichia coli and Staphylococcus epidermidis strains. The results demonstrated that nanopatterned films actually improved the conditions for bacterial growth compared to pristine PLLA films, the novelty is based on formation of Ag nanoparticles on the surface/and in bulk, while silver nanoparticle enhanced and nanopatterned films exhibited excellent antibacterial activity against both bacterial strains, with circa 80 % efficacy in 4 h and complete bactericidal effect in span of 24 h., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2023 The Authors.)

The irreconcilable paradox between barrier performance and ductility is a "stumbling block" restricting the development of poly(L-lactic acid) (PLLA) films in the packaging industry. In this work, we reported the fabrication of an ultra-thin PLLA-based film with barrier properties and ductility by adjusting the polarity and conformational behavior of the polymer chains. Firstly, a novel unsaturated poly(L-lactic acid-co-butyrate itaconate) P(LA-BI) copolymer containing CC double bonds was synthesized using melt polycondensation. The results reveal that the addition of 60 % of P(LA-BI) enables PLLA film to achieve an elongation at a break of 83.6 % due to P(LA-BI) containing partially branched structures, which resulted in the polymer chains being arranged more in a high-energy gg conformer. Meanwhile, because of the large number of CO polar groups in P(LA-BI), PLLA/P(LA-BI) 60 film show CO 2 and O 2 permeability coefficients (CDP and OP) of 1.8 and 0.45 × 10 -8  g·m·m -2 ·h -1 ·Pa -1 respectively, which means that it has excellent gas barrier properties. Moreover, PLLA/P(LA-BI) 60 film shows a 33.3 % increase in CO 2 /O 2 ratio and an excellent ultraviolet (UV) barrier performance compared to neat PLLA. Preservation results suggested that the CO 2 and O 2 levels within the package could be regulated by varying the amount of P(LA-BI) added. Among them, PLLA/P(LA-BI) 40 film generated a more desirable CO 2 and O 2 atmosphere for cherry tomatoes preservation, which was reflected by the delaying of senescence, discoloration, and decay, inhibition of oxidative cell damage through reduced malondialdehyde production, and maintenance of nutritional and flavor substances in cherry tomatoes. This PLLA-based film offers the advantages of operational simplicity, environmental friendliness, and inexpensive cost, making it great promising for food preservation and other applications requiring barrier properties and ductility., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

Poly(L-lactic acid) (PLLA) and PLLA/gelatin polymers were prepared via electrospinning to evaluate the effect of PLLA and gelatin content on the mechanical properties, water uptake capacity (WUC), water contact angle (WCA), degradation rate, cytotoxicity and cell proliferation of membranes. As the PLLA concentration increased from 1 wt% to 3 wt%, the tensile strength increased from 5.8 MPa to 9.1 MPa but decreased to 7.0 MPa with 4 wt% PLLA doping. The WUC decreased rapidly from 594% to 236% as the PLLA content increased from 1 to 4 wt% due to the increased hydrophobicity of PLLA. As the gelatin content was increased to 3 wt% PLLA, the strength, WUC and WCA of the PLLA/gelatin membrane changed from 9.1 ± 0.9 MPa to 13.3 ± 2.3 MPa, from 329% to 1248% and from 127 ± 1.2° to 0°, respectively, with increasing gelatin content from 0 to 40 wt%. However, the failure strain decreased from 3.0 to 0.5. The biodegradability of the PLLA/gelatin blend increased from 3 to 38% as the gelatin content increased to 40 wt%. The viability of L-929 and MG-63 cells in the PLLA/gelatin blend was over 95%, and the excellent cell proliferation and mechanical properties suggested that the tunable PLLA/gelatin barrier membrane was well suited for absorbable periodontal tissue regeneration.

The aim of this study is to prepare new packaging materials with improved physical and antimicrobial properties that prevent the growth of microorganisms. Poly(L-lactic acid) (PLA) based packaging films were prepared by the solvent-casting method using spruce resin (SR), epoxidized soybean oil, an essential oil mixture (calendula and clove oil), and silver nanoparticles (AgNPs). The AgNPs were synthesized by the polyphenol reduction method, using spruce resin dissolved in methylene chloride. The prepared films were tested for antibacterial activity and physical properties, such as tensile strength (TS), elongation at break (EB), elastic modulus (EM), water vapor permeability (WVP), and UV-C blocking effect. The addition of SR decreased the water vapor permeation (WVP) of the films, whereas the addition of essential oils (EOs) increased this property due to their higher polarity. The morphological, thermal, and structural properties were characterized using SEM, UV-Visible spectroscopy, FTIR, and DSC. The agar disc well method showed that SR, AgNPs, and EOs imparted antibacterial activity to the PLA-based films against Staphylococcus aureus and Escherichia coli. Multivariate data analysis tools, such as principal component and hierarchical cluster analysis, were used to discriminate PLA-based films by simultaneously evaluating their physical and antibacterial properties., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

Bone tissue engineering has become one of the most promising therapeutic methods to treat bone defects. A suitable scaffolding material to regenerate new bone tissues should have a high specific surface area, high porosity and a suitable surface structure which benefit cell attachment, proliferation, and differentiation. In this study, an acetone post-treatment strategy was developed to generate heterogeneous structure. After PLLA/PCL nanofibrous membranes were electrospun and collected, they were treated with acetone to generate a highly porous structure. Meanwhile, part of PCL was extracted from the fibre and enriched on the fibre surface. The cell affinity of the nanofibrous membrane was verified by human osteoblast-like cells assay. The proliferation rate of heterogeneous samples increased 190.4 %, 265.5 % and 137.9 % at day 10 compared with pristine samples. These results demonstrated that the heterogeneous PLLA/PCL nanofibrous membranes could enhance osteoblast adhesion and proliferation. With high surface area (average surface area 36.302 m 2 /g) and good mechanical properties (average Young's modulus 1.65 GPa and average tensile strength 5.1 MPa), the heterogeneous PLLA/PCL membrane should have potential applications in the field of bone regeneration., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 The Authors. Published by Elsevier B.V. All rights reserved.)

In this work, the β-cyclodextrin (β-CD) was modified by a phosphazene compound to prepare a novel amorphous derivate (β-CDCP), which was combined with the ammonium polyphosphate (APP) as a synergistic flame retardant (FR) of the bio-based poly(L-lactic acid) (PLA). The effects of the APP/β-CDCP on the thermal stability, combustion behavior, pyrolysis process, fire resistance performance and crystallizability of the PLA were investigated comprehensively and in depth by thermogravimetric (TG) analysis, limited oxygen index (LOI) analysis, UL-94 test, cone calorimetry measurement, TG-infrared (TG-IR), scanning electron microscopy-energy dispersive spectrometer, Raman spectroscopy, pyrolysis-gas chromatography/mass spectrometry and differential scanning calorimetry. The PLA/5%APP/10%β-CDCP showed a highest LOI of 33.2 %, passed V-0 rating and exhibited self-extinguish phenomenon in the UL-94 test. Also, it presented a lowest peak of heat release rate, total heat release, peak of smoke production rate and total smoke release, and a highest char yield treated by cone calorimetry analysis. In addition, the 5%APP/10%β-CDCP shortened significantly crystallization time and enhanced crystallization rate of the PLA. Gas phase and intumescent condensed phase fire proofing mechanisms are proposed to elucidate enhanced fire resistance in this system in detail., Competing Interests: Declaration of competing interest The authors declare no any competing financial interest., (Copyright © 2023. Published by Elsevier B.V.)

Despite good biodegradability and mechanical strength, the intrinsic flammability of poly(L-lactic acid) (PLA) impede its practical application. Introducing phosphoramide is an effective method to enhance the flame retardancy of PLA. However, most of the reported phosphoramides derive from petroleum resources, and their addition tends to deteriorate the mechanical properties, especially toughness, of PLA. Herein, a bio-based, furan-containing polyphosphoramide (DFDP) with high flame-retardant efficiency was synthesized for PLA. Our study found that 2 wt% DFDP enabled PLA to pass a UL-94 V-0 rating, and 4 wt% DFDP increased the limiting oxygen index (LOI) to 30.8 %. DFDP effectively maintained the mechanical strength and toughness of PLA. The tensile strength of PLA with 2 wt% DFDP reached 59.9 MPa, and its elongation at break and impact strength were increased by 15.8 % and 34.3 %, respectively, relative to those of virgin PLA. The UV protection of PLA was significantly enhanced by introducing DFDP. Hence, this work provides a sustainable and comprehensive strategy for the creation of flame-retardant biomaterials with improved UV protection and well-preserved mechanical properties, which possess a broad prospect in industrial application., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

PLD x L copolymers were synthesized from physically stable rigid poly(l-lactic acid) (PLLA) and a few different molecular weights of polydimethylsiloxane (PDMS) to increase the O 2 and CO 2 permeabilities of PLLA films and make them acceptable for packaging highly respirable products. The effect of PDMS on the morphology, mechanical properties, and gas permeability of PLD x L was investigated. Copolymers showed approximately 10 times the fracture strain and 1.7 times the CO 2 and O 2 permeabilities of neat PLLA. Additionally, PLD x L maintained an increased CO 2 /O 2 perm-selectivity consistent between 5 and 40°C. Passive modified atmosphere packaging of Brassica chinensis L was developed to assess the membrane's impact on headspace gas inside the package. The results showed that poly(amide)/poly(ethylene) packaging with 48 cm 2 PLD 1.8 L membrane as a breathing window can provide 50 g B. chinensis L. with a healthy atmosphere of 3%-8% O 2 and 5%-8% CO 2 between 6 and 22 days. Vegetables packaged in PLD 1.8 L had the lower respiration rate, lower nitrite contents, and less proliferation of microorganisms. Moreover, a suitable atmosphere kept vegetables with higher ascorbic acid and a good appearance after more than 2 weeks of storage at 5°C. PRACTICAL APPLICATION: The permeability of the PLLA-based membrane can be adjusted for the breathable window membrane of sealed fresh products. In the future, several types of film could be developed to match the respiratory and metabolic characteristics of different kinds of products. Such PLLA-based specialized membranes can refine the fresh-keeping function and be more attractive to the customer., (© 2023 Institute of Food Technologists.)

Objective: The primary objective of this research was to develop a poly(l-lactic acid) (PLLA) scaffold and evaluate critical characteristics essential for its biologic use as a craniofacial implant., Materials and Methods: PLLA scaffolds were designed and fabricated using fused deposition modeling technology. The surface morphology and microarchitecture were analyzed using scanning electron microscopy (SEM) and microCT, respectively. Crystallography, compressive modulus, and the piezoelectric potential generated upon mechanical distortion were characterized. Hydrolytic degradation was studied. MG63 osteoblast-like cell proliferation and morphology were assessed., Results: The porosity of the scaffolds was 73%, with an average pore size of 450 µm and an average scaffold fiber thickness of 130 µm. The average compressive modulus was 244 MPa, and the scaffolds generated an electric potential of 25 mV upon cyclic/repeated loading. The crystallinity reduced from 27.5% to 13.9% during the 3D printing process. The hydrolytic degradation was minimal during a 12-week period. Osteoblast-like cells did not attach to the uncoated scaffold but attached well after coating the scaffold with fibrinogen. They then proliferated to cover the complete scaffold by Day 14., Conclusion: The PLLA scaffolds were designed and printed, proving the feasibility of 3D printing as a method of fabricating PLLA scaffolds. The elastic modulus was comparable to that of trabecular bone, and the piezoelectric properties of the PLLA were retained after 3D printing. The scaffolds were cytocompatible. These 3D-printed PLLA scaffolds showed promising properties akin to the natural bone, and they warrant further investigation for bone regeneration., (© 2023 The Authors. Clinical and Experimental Dental Research published by John Wiley & Sons Ltd.)

Background: Electrospun fibers are widely studied in regenerative medicine for their ability to mimic the extracellular matrix (ECM) and provide mechanical support. In vitro studies indicated that cell adhesion and migration is superior on smooth poly(L-lactic acid) (PLLA) electrospun scaffolds and porous scaffolds once biofunctionalized with collagen., Methods: The in vivo performance of PLLA scaffolds with modified topology and collagen biofunctionalization in full-thickness mouse wounds was assessed by cellular infiltration, wound closure and re-epithelialization and ECM deposition., Results: Early indications suggested unmodified, smooth PLLA scaffolds perform poorly, with limited cellular infiltration and matrix deposition around the scaffold, the largest wound area, a significantly larger panniculus gape, and lowest re-epithelialization; however, by day 14, no significant differences were observed. Collagen biofunctionalization may improve healing, as collagen-functionalized smooth scaffolds were smallest overall, and collagen-functionalized porous scaffolds were smaller than non-functionalized porous scaffolds; the highest re-epithelialization was observed in wounds treated with collagen-functionalized scaffolds., Conclusion: Our results suggest that limited incorporation of smooth PLLA scaffolds into the healing wound occurs, and that altering surface topology, particularly by utilizing collagen biofunctionalization, may improve healing. The differing performance of the unmodified scaffolds in the in vitro versus in vivo studies demonstrates the importance of preclinical testing.

To avoid infection and other risks caused by large open-surgery incisions using scaffold transplants, it is very important to study injectable microcarrier-loaded cells for targeted therapy and tissue regeneration. In this study, on the one hand, to simulate the hierarchical structure of the extracellular matrix and carry cells, poly(L-lactic acid) (PLLA) nanofibrous microspheres (large microspheres) were initially fabricated as cell carriers. On the other hand, to precisely deliver cells through a magnetic field and promote stem cell differentiation, drug-loaded mesoporous Fe 3 O 4 @SiO 2 microspheres (small microspheres) were prepared and coated on the surface PLLA nanofibrous microspheres. The coating conditions were systematically studied and optimized. The results showed that planetary-satellite-like cell carriers were successfully prepared and the carriers were capable of freely translocating under the influence of a magnetic field. It has been demonstrated in vitro experiments that the carriers are biocompatible and are capable of acting as drug carriers. Specifically, they were able to load and release cells in response to magnetic fields. In vivo experiments indicated that the carriers could successfully load and release GFP-labelled cells in nude mice. The study presented in this paper provides a versatile and promising platform for the cell-based therapy in tissue engineering and regenerative medicine., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2023 Elsevier B.V. All rights reserved.)

Poly (L-lactic acid) (PLLA) braided stents, which are expected to replace metal stents, are promising in peripheral vascular therapy due to their superior biocompatibility. Although various design ideas have been proposed and investigated on metal stents, few researches are related to the design theory of PLLA braided stent. In this article, mechanical performance of PLLA braided stents with different parameters was systematically evaluated, and a design theory based on material properties was proposed. Different from metal materials, the risk of filament deformation beyond elastic zone should be evaluated and controlled in PLLA stent design. The findings were obtained through combination study of experiments and simulations. Design parameters, including pitch angle and stent diameter, played a crucial role in mechanical performance of PLLA braided stent. The deformation of PLLA stents with larger pitch angles and stent diameters was in elastic zone and thus presented better mechanical performance with satisfactory resilience. This work could provide meaningful suggestions for preparing bioresorbable braided stents with suitable design parameters., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022. Published by Elsevier Ltd.)

In this work, PLLA and CD/PLLA nanofibers were fabricated using electrospinning and utilized as a particulate matter (PM) and volatile organic compounds (VOCs) filter. The electrospun PLLA and CD/PLLA were characterized with various techniques, including SEM, BET, FTIR, XRD, XPS, WCA, DSC, tensile strength testing, PM and VOCs removal efficiency, and triboelectric performance. The results demonstrated that the best air filter was 2.5 wt%CD/PLLA, which performed the highest filtration efficiencies of 96.84 ± 1.51% and 99.38 ± 0.43% for capturing PM 2.5 and PM 10 , respectively. Its PM 2.5 removal efficiency was 16% higher than that of pure PLLA, which were contributed by their higher surface area and porosity. These 2.5 wt%CD/PLLA nanofibers also exhibited the highest and the fastest VOC entrapment. For triboelectric outputs, the 2.5 wt%CD/PLLA-based triboelectric nanogenerator provided the highest electrical outputs as 245 V and 84.70 μA. These give rise to a three-fold enhancement of electrical outputs. These results indicated that the 2.5 wt%CD/PLLA can improve surface charge density that could capture more PM via electrostatic interaction under surrounding vibration. Therefore, this study suggested that 2.5 wt%CD/PLLA is a good candidate for a multifunction nanofibrous air filter that offers efficient PM and VOC removal.

Adding nucleating agents has been a successful strategy to boost the heat resistance of poly(L-lactic acid) (PLLA) by increasing the crystallinity. In this study, a new series of bio-based complexes as nucleating agents for PLLA, including twelve combinations of three eco-friendly metal ions (Zn, Mg, Ca) and four biomass-derived α-hydroxy acids, were successfully synthesized to respectively investigate the effects of metal ions as well as ligands on nucleation capacity of complexes. By investigating the non-isothermal and isothermal crystallization at 135 °C of PLLA with 0.3 wt% loading of complexes, both zinc and magnesium salts of L-mandelic acid showed excellent nucleation capacities. And magnesium L-mandelate performed better, raising the crystallinity of PLLA to 44.4 % as well as minimizing its crystallization half-time from 73 min to 2.7 min. The growth and denser distribution of PLLA spherulites on the salt surface were also observed by POM, reflecting epitaxial nucleation as the possible mechanism. A novel inspiration, utilizing VESTA software to simulate the crystal structure of zinc L-mandelate (Zn(L-MA) 2 ), was proposed to determine the nucleation mechanism. Also, using polyethylene terephthalate (PET) as a test protocol, the rationality of the model could be approved by checking the fitness of nucleating prediction and experiment results., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022. Published by Elsevier B.V.)

The use of biodegradable materials such as cellulose and polyesters can be extended through the combination, as well as modification, of these biopolymers. By controlling the molecular structure and composition of copolymers of these components, it should also be possible to tailor their material properties. We hereby report on the synthesis and characterization of cellulose-based graft copolymers with a precise molecular composition and copolymer architecture. To prepare such materials, we initially modified cellulose through the regioselective protection of the 6-OH group using trityl chloride. The 6-O protected compound was then alkylated, and deprotection at the 6-OH group provided the desired 2,3-di-O-alkyl cellulose compounds that were used as macroinitiators for ring opening polymerization. Regioselective modification was hereby necessary to obtain compounds with an exact molecular composition. Ring opening polymerization, catalyzed by Sn(Oct) 2 , at the primary 6-OH group of the cellulose macroinitiator, using L-lactide or ε-caprolactone, resulted in graft copolymers with the desired functionalization pattern. The materials were characterized using Fourier-transform infrared spectroscopy, 1 H- and 13 C- nuclear magnetic resonance spectroscopy, size exclusion chromatography as well as X-ray diffraction, and differential scanning calorimetry. PCL-based copolymers exhibited distinct melting point as well as a crystalline phase of up to 47%, while copolymers with PLA segments were highly amorphous, showing a broad amorphous reflex in the XRD spectra, and no melting or crystallization points were discernible using differential scanning calorimetry.

In the context of today's needs for environmental sustainability, it is important to develop new materials that are based on renewable resources and biodegrade at the end of their life. Bioplastics reinforced by agricultural waste have the potential to cause a revolution in many industrial applications. This paper reports the physical properties and crystallization kinetics of biocomposite films based on poly(L-lactic acid) (PLLA) and 10 wt.% of spent coffee grounds (SCG). To enhance adhesion between the PLLA matrix and SCG particles, a compatibilizing agent based on itaconic anhydride (IA)-grafted PLLA (PLLA-g-IA) was prepared by reactive extrusion using dicumyl peroxide (DCP). Furthermore, due to the intended application of the film in the packaging industry, the organic plasticizer acetyl tributyl citrate (ATBC) is used to improve processing and increase ductility. The crystallization behavior and thermal properties were observed by differential scanning calorimetry (DSC) and thermogravimetric analysis (TGA). Crystallinity degree increased from 3,5 (neat PLLA) up to 48% (PLLA/PLLA-g-IA/ATBC/SCG) at the highest cooling rate. The physical properties were evaluated by tensile testing and dynamic mechanical analysis (DMA). The combination of the compatibilizer, SCG, and ATBC led to a synergistic effect that positively influenced the supramolecular structure, internal damping, and overall ductility of the composite films.

An atmosphere within a package affects the metabolic process of food and the microbial growth of fresh products and has a vital role in preserving food. It depends on the membrane's specific gas permeability and selectivity to generate a desirable atmosphere for storage. In this study, triblock poly(l-lactic acid‑d-ɛ-caprolactone) (PLDC) copolymers and three-arm poly(l-lactic acid-g-ɛ-caprolactone) (PLGC) star copolymers were synthesized, in which a microphase-separated morphology of sea-island structure was established in PLGC membrane as a gas "fast permeation channel" for regulating CO 2 and O 2 permeability and CO 2 /O 2 selectivity. AFM observation revealed different well-defined micro phase-separated structures of PLGC with size ranges of 200- 300 nm. Comparing PLGC membrane with PLLA, CO 2 and O 2 transmission rates increased by 416.9 % and 132.7 %, while H 2 O transport rates increased by 245.6 %. Mechanical testing shows that the PLGC membrane exhibits 40.8-fold elongation at break compared to PLLA, showing excellent flexibility. Moreover, okra's equilibrium-modified atmosphere packaging was designed based on a theoretically derived model. Preservation results suggested that the PLGC packaging membrane could generate an ideal high 8.7- 9.2 % CO 2 and low 2.3- 2.7 % O 2 atmosphere for okra preservation, delaying the discoloring and rotting of okra., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022. Published by Elsevier B.V.)

Poly(L-lactic acid) (PLLA) braided stents have superior biocompatibility and flexibility, substituting metal stents in peripheral blood vessels. However, the radial supporting capacity of PLLA braided stent should be improved to bear the dynamic load from the peripheral artery. This paper evaluated the radial support performance of PLLA braided stents with different braiding angles after the radial cyclic loads test. The results indicate that braiding angle of stents is an important parameter affecting its ability to resist radial cyclic loads. The stent with a smaller braiding angle has better initial radial support but insufficient durability, while the stent with a larger braiding angle could maintain adequate radial support and suitable ability to resist radial cyclic loads. The theoretical analysis, verified by observing the surface morphology of filament crossover points, found that filaments of the stents with smaller braiding angles have more significant axial displacement and axial rotation angle during radial compression, which made the friction phenomenon more intense and led to insufficient ability to resist radial cyclic loads. This study could provide a meaningful idea for preparing biodegradable braided stents with suitable ability to resist radial cyclic loads., Competing Interests: Declaration of competing interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier B.V. All rights reserved.)

Poly(L-lactic acid) (PLLA), as a biodegradable polymer, has attracted attention for use as a biomaterial. In order to apply PLLA as a cardiovascular stent, stronger mechanical properties and anti-inflammatory effects against acidic by-products are required. In this study, PLLA/PDLA stereocomplex microparticles (SC) were developed and surface-modified magnesium hydroxide (MH) nanoparticles with oligolactide were combined with these PLLA composites. The SC improved the mechanical properties of the PLLA composites through the formation of stereocomplex structures. The surface-modified MH nanoparticles showed enhanced mechanical properties due to the stereocomplex structures formed by PLLA chains and inhibited inflammatory responses by pH neutralization as a result of MH. Additionally, the MH nanoparticles containing PLLA composites had antibacterial effects and increased the viability of human vascular endothelial cells. This technology is expected to have great potential in the development of PLLA composite materials for the production of various medical devices, such as cardiovascular stents.

Effects of montmorillonite (MMT) on the crystallization behavior of poly(L-lactic acid) (PLLA) were investigated by variable-temperature FTIR spectroscopy. The variations of carbonyl band (1800-1720 cm -1 ) of different PLLA/MMT nanocomposites were focused due to its strong intensity and the involved abundant structure information. Difference spectrometry was used to evaluate the structural variations of PLLA after introducing MMT, and perturbation correlation moving window two-dimensional analysis (PCMW2D) split the temperature range into two sub-regions, i.e., 32-116 ℃ and 116-152 ℃, on the basis of the spectral variation. Two-dimensional correlation spectroscopy (2DCOS) was further applied to such sub-regions in order to find the change order between varied PLLA polymorphs. The results showed that less addition of MMT (≤3%) would lead to a well-exfoliated structure, which not only had no nucleation effect for PLLA, but also delayed the cold crystallization to a higher temperature compared with the one of pure PLLA. However, a higher addition of MMT (≥5%) would lead to an intercalated structure, which acted as a nucleating agent and thus advanced the cold crystallization to a lower temperature. Nevertheless, the introduction of MMT cannot affect the phase transition order between the amorphous, the intermediate, the α'- and the α'-PLLAs based on 2DCOS results., Competing Interests: Declaration of Competing Interest The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2022 Elsevier B.V. All rights reserved.)

The polymer/solvent system poly(l-lactic acid)/ethyl butylacetylaminopropionate (PLLA/IR3535) is regarded as an insect-repellent-delivery system, serving, e.g., for fighting mosquito-borne tropical diseases. In such systems the solid polymer hosts the liquid repellent, with the latter slowly released to the environment, expelling mosquitoes. As a new approach, exceeding prior work about application of different technologies to obtain such devices, in this work, samples of the polymer/repellent system PLLA/IR3535 were prepared by 3D-printing. The experiments showed that it is possible to print 3D-parts containing up to 25 m% repellent, with an only minor loss of repellent during the printing process. For samples containing low amount of repellent, crystallization of PLLA was suppressed due to the rather fast cooling step and the low bed temperature of around 25 °C, being lower than the glass transition temperature of the homogeneous polymer/repellent strands. At higher repellent concentration, due to the lowering of the glass transition temperature to near or even below ambient temperature, the crystallinity slowly increased during storage after printing. For all samples, regardless of the initial repellent concentration, the repellent-release rate increases with temperature, and at ambient temperature the release-time constant is in the order of 10 days. The study successfully proved the applicability of the technology of extrusion-based 3D-printing for the preparation of polymer parts with a specific shape/design containing mosquito-repellent at a concentration which raises the expectation to be used as a repellent delivery-device., (Copyright © 2022 Elsevier B.V. All rights reserved.)

Poly(l-lactic acid) (PLLA) displays simultaneous repair and regeneration properties. Therefore, it is vital for developing bone repair materials while improving their mechanical strength, and biocompatibility is essential for guaranteeing its application. In this manuscript, using solid hot drawing (SHD) technology to fabricate an oriented shish-kebab like structure, furthermore, the interface-oriented grain boundary controlled the nucleation site and cell morphology during low temperature supercritical carbon dioxide (SC-CO 2 ) foaming process, resulted in an oriented microcellular structure which was similar to load-bearing bone. The tensile strength, elastic modulus, and elongation at break of the oriented microcellular PLLA were 98.4 MPa, 3.3 GPa, and 16.4%, respectively. Furthermore, the biomimetic structure improved osteoblast cells (MC3T3) attachment, proliferation, and propagation. These findings may pave the way for designing novel biomaterials for bone fixation or tissue engineering devices., (Copyright © 2022 Elsevier B.V. All rights reserved.)

Enabling a biodegradable polymer radiopaque under X-ray is much desired for many medical devices. Physical blending of a present biodegradable polymer and a commercialized medical contrast agent is convenient yet lacks comprehensive fundamental research. Herein, we prepared a biodegradable polymer-based radiopaque raw material by blending poly(l-lactic acid) (PLLA or simply PLA) and iohexol (IHX), where PLA constituted the continuous phase and IHX particles served as the dispersed phase. The strong X-ray adsorption of IHX enabled the composite radiopaque; the hydrolysis of the polyester and the water solubility of the contrast agent enabled the composite biodegradable in an aqueous medium. The idea was confirmed by in vitro characterizations of the resultant composite, in vivo subcutaneous implantation in rats up to 6 months, and the clear visualization of a part of a biodegradable occluder in a Bama piglet under X-ray. We also found that the crystallization of PLA was significantly enhanced in the presence of the solid particles, which should be taken into consideration in the design of an appropriate biomaterial composite because crystallization degree influences the biodegradation rate and mechanical property of a material to a large extent. We further tried to introduce a small amount of poly(vinylpyrrolidone) into the blend of PLA and IHX. Compared to the bicomponent composite, the tricomponent one exhibited decreased modulus and increased elongation at break and tensile strength. This paves more ways for researchers to select appropriate raw materials according to the regenerated tissue and the application site.

As an emerging additive manufacturing (AM) technique, melt electrospinning writing (MEW) is used to fabricate three-dimensional (3D) submicron filament-based scaffolds with adjustable pore size and customized structure for bone regeneration. Poly(L-lactic acid) (PLLA) scaffold with excellent biodegradability and biocompatibility is first successfully manufactured using our self-assembled MEW device. However, the ultralow cell affinity and poor bioactivity severely hamper their practical applications in bone tissue engineering. These issues are caused by the severe inherent biologically inert, hydrophobicity as well as the smooth surface of the MEW PLLA filaments. In this study, a green and robust alkaline method is applied to modify the scaffold surface and to improve the bioactivity of the MEW PLLA scaffold. Without deterioration in mechanical property but robust surface hydrophilicity, the optimal MEW PLLA scaffold shows promoted surface roughness, enhanced filament tensile modulus (~ 2 folds of the as-prepared sample), and boosted crystallizability (ultrahigh WAXD intensity). Moreover, after being cultured with KUSA-A1 cells, the 0.5 M NaOH, 2 h treated MEW PLLA scaffold exhibits higher osteoinductive ability and increased immature bone tissue amounts (3 times of controlled scaffold). Thus, the flexible surface functionalization by the specific alkaline treatment was found to be an effective method for the preparation of bioactivated MEW PLLA scaffolds with promoted bone regeneration., (Copyright © 2022. Published by Elsevier B.V.)

The 5-year survival rate for pancreatic cancer remains low, and the development of new methods for its treatment is actively underway. After the surgical treatment of pancreatic cancer, recurrence and peritoneal dissemination can be prevented by long-term local exposure to appropriate drug concentrations. We propose a novel treatment method using non-woven sheets to achieve this goal. Poly(L-lactic acid) non-woven sheets containing gemcitabine (GEM) were prepared, and GEM sustained release from this delivery system was investigated. Approximately 35% of the GEM dose was released within 30 d. For in vitro evaluation, we conducted a cell growth inhibition test using transwell assays, and significant inhibition of cell growth was observed. The antitumor effects of subcutaneously implanted GEM-containing non-woven sheets were evaluated in mice bearing subcutaneous Panc02 cells, and it was established that the sheets inhibited tumor growth for approximately 28 d. These results suggest the usefulness of GEM-containing non-woven sheets in pancreatic cancer treatment.

Electrospun nanofiber mats have attracted intense attention as advanced wound dressing materials. The objective of this study was to fabricate methacrylated gelatin (MeGel)/poly(L-lactic acid) (PLLA) hybrid nanofiber mats with an extracellular matrix (ECM) mimicking nanofibrous structure and hydrogel-like properties for potential use as wound dressing materials. MeGel was first synthesized via the methacryloyl substitution of gelatin (Gel), a series of MeGel and PLLA blends with various mass ratios were electrospun into nanofiber mats, and a UV crosslinking process was subsequently utilized to stabilize the MeGel components in the nanofibers. All the as-crosslinked nanofiber mats exhibited smooth and bead-free fiber morphologies. The MeGel-containing and crosslinked nanofiber mats presented significantly improved hydrophilic properties (water contact angle = 0°; 100% wettability) compared to the pure PLLA nanofiber mats (~127°). The swelling ratio of crosslinked nanofiber mats notably increased with the increase of MeGel (143.6 ± 7.4% for PLLA mats vs. 875.0 ± 17.1% for crosslinked 1:1 MeGel/PLLA mats vs. 1135.2 ± 16.0% for crosslinked MeGel mats). The UV crosslinking process was demonstrated to significantly improve the structural stability and mechanical properties of MeGel/PLLA nanofiber mats. The Young's modulus and ultimate strength of the crosslinked nanofiber mats were demonstrated to obviously decrease when more MeGel was introduced in both dry and wet conditions. The biological tests showed that all the crosslinked nanofiber mats presented great biocompatibility, but the crosslinked nanofiber mats with more MeGel were able to notably promote the attachment, growth, and proliferation of human dermal fibroblasts. Overall, this study demonstrates that our MeGel/PLLA blend nanofiber mats are attractive candidates for wound dressing material research and application.

A poly(l-lactic acid)/nanohydroxyapatite (PLLA/nHA) scaffold works as a bioactive, osteoconductive scaffold for bone-tissue engineering, but its low degradation rate limits embedded HA in PLLA to efficiently interact with body fluids. In this work, nano-hydroxyapatite (nHA) was added in lower filler loadings (1, 5, 10, and 20 wt%) in a poly(l-lactic acid)/cyclo olefin copolymer10 wt% (PLLA/COC10) blend to obtain novel poly(l-lactic acid)/cyclo olefin copolymer/nanohydroxyapatite (PLLA/COC10-nHA) scaffolds for bone-tissue regeneration and repair. Furthermore, the structure-activity relationship of PLLA/COC10-nHA (ternary system) nanocomposites in comparison with PLLA/nHA (binary system) nanocomposites was systematically studied. Nanocomposites were evaluated for structural (morphology, crystallization), thermomechanical properties, antibacterial potential, and cytocompatibility for bone-tissue engineering applications. Scanning electron microscope images revealed that PLLA/COC10-nHA had uniform morphology and dispersion of nanoparticles up to 10% of HA, and the overall nHA dispersion in matrix was better in PLLA/COC10-nHA as compared to PLLA/nHA. Fourier transformation infrared spectroscopy (FTIR), powder X-ray diffraction (XRD), and differential scanning calorimetry (DSC) studies confirmed miscibility and transformation of the α-crystal form of PLLA to the ά-crystal form by the addition of nHA in all nanocomposites. The degree of crystallinity (%) in the case of PLLA/COC10-nHA 10 wt% was 114% higher than pure PLLA/COC10 and 128% higher than pristine PLLA, indicating COC and nHA are acting as nucleating agents in the PLLA/COC10-nHA nanocomposites, causing an increase in the degree of crystallinity (%). Moreover, PLLA/COC10-nHA exhibited 140 to 240% (1-20 wt% HA) enhanced mechanical properties in terms of ductility as compared to PLLA/nHA. Antibacterial activity results showed that 10 wt% HA in PLLA/COC10-nHA showed substantial activity against P. aeruginosa , S. aureus , and L. monocytogenes . In vitro cytocompatibility of PLLA/COC10 and PLLA nanocomposites with nHA osteoprogenitor cells (MC3T3-E1) and bone mesenchymal stem cells (BMSC) was evaluated. Both cell lines showed two- to three-fold enhancement in cell viability and 10- to 30-fold in proliferation upon culture on PLLA/COC10-nHA as compared to PLLA/nHA composites. It was observed that the ternary system PLLA/COC10-nHA had good dispersion and interfacial interaction resulting in improved thermomechanical and enhanced osteoconductive properties as compared to PLLA/nHA.

Poly(L-lactic acid) (PLLA) has attracted a great deal of attention for its use in biomedical materials such as biodegradable vascular scaffolds due to its high biocompatibility. However, its inherent brittleness and inflammatory responses by acidic by-products of PLLA limit its application in biomedical materials. Magnesium hydroxide (MH) has drawn attention as a potential additive since it has a neutralizing effect. Despite the advantages of MH, the MH can be easily agglomerated, resulting in poor dispersion in the polymer matrix. To overcome this problem, oligo-L-lactide-ε-caprolactone (OLCL) as a flexible character was grafted onto the surface of MH nanoparticles due to its acid-neutralizing effect and was added to the PLLA to obtain PLLA/MH composites. The pH neutralization effect of MH was maintained after surface modification. In an in vitro cell experiment, the PLLA/MH composites including OLCL-grafted MH exhibited lower platelet adhesion, cytotoxicity, and inflammatory responses better than those of the control group. Taken together, these results prove that PLLA/MH composites including OLCL-grafted MH show excellent augmented mechanical and biological properties. This technology can be applied to biomedical materials for vascular devices such as biodegradable vascular scaffolds.

Poly(l-lactic acid) (PLLA) crystal possesses a complex polymorphism, and the formation mechanism of various crystal forms has been a hot research topic in the field of polymer condensate matter. In this research, five kinds of PLLA with different molecular weights were prepared by ring-opening polymerization with strict dehydration operations and multistep purification treatments. Then, thin film isothermal crystallization experiments were carried out to obtain crystallized samples. Previous research has proven that the PLLA α crystal form is usually formed at a temperature above 120 °C and the PLLA δ (or α') crystal form is usually formed at a temperature below 120 °C. However, in this research, the characterization results indicated that the PLLA crystal changed from δ form to α form with the decrease of molecular weight at a temperature of 80 °C. Considering the molecular weight effect, the paper argued that the transitions of the α/δ crystal form are not only associated with temperature, but also related to entanglement state before crystallization. The small-angle X-ray scattering of the PLLA crystal and rheology analysis of the PLLA melt before crystallization further proved the significant role of entanglement. Finally, we tentatively proposed the entanglement effect mechanism on the transitions of the α/δ crystal form.

Poly(L-lactic acid) (PLLA) blends with excellent low-temperature toughness and strength were prepared by melt compounding with acrylic ester based impact resistance agent (AEIR). The morphology, thermal properties, mechanical properties and biodegradability of the blends were investigated. Morphology observations revealed the blend was immiscible but had good compatibility with the dispersed phase size of about 200-300 nm. With the addition of AEIR, dramatic improvement in toughness of PLLA was achieved in a wide temperature range, especially at low temperatures the tensile strength was effectively remained. For the blend with 20 wt% AEIR, the tensile strength, elongation at break and impact strength were 51.6 MPa, 72% and 77.1 KJ/m 2 at -20 °C, respectively, much greater than that reported. The calculated T g of AEIR was lower than the test temperatures, and the brittle-tough transition occurred. The PLLA matrix demonstrated obvious shear yielding which induced energy dissipation and therefore lead to excellent toughness of the blends. Moreover, the biodegradation of PLLA was enhanced after blends preparation., (Copyright © 2021 Elsevier B.V. All rights reserved.)

The next-generation closure device for interventional treatment of congenital heart disease is regarded to be biodegradable, yet the corresponding biomaterial technique is still challenging. Herein, we report the first fully biodegradable atrial septal defect (ASD) occluder finally coming into clinical use, which is made of biodegradable poly(l-lactic acid) (PLLA). We characterized the physico-chemical properties of PLLA fibers as well as the raw polymer and the operability of the as-fabricated occluders. Cell behaviors on material were observed, and in vivo fiber degradation and inflammatory responses were examined. ASD models in piglets were created, and 44 PLLA ASD occluders were implanted via catheter successfully. After 36 months, the PLLA ASD occluders almost degraded without any complications. The mechanical properties and thickness between newborn and normal atrial septum showed no significant difference. We further accomplished the first clinical implantation of the PLLA ASD occluder in a four-year boy, and the two-year follow-up up to date preliminarily indicated safety and feasibility of such new-generation fully biodegradable occluder made of synthetic polymers., (Copyright © 2021 Elsevier Ltd. All rights reserved.)

The present study evaluates the use of newly synthesized poly(l-lactic acid)-co-poly(butylene adipate) (PLA/PBAd) block copolymers as microcarriers for the preparation of aripiprazole (ARI)-loaded long acting injectable (LAI) formulations. The effect of various PLA to PBAd ratios (95/5, 90/10, 75/25 and 50/50 w / w ) on the enzymatic hydrolysis of the copolymers showed increasing erosion rates by increasing the PBAd content, while cytotoxicity studies revealed non-toxicity for all prepared biomaterials. SEM images showed the formation of well-shaped, spherical MPs with a smooth exterior surface and no particle's agglomeration, while DSC and pXRD data revealed that the presence of PBAd in the copolymers favors the amorphization of ARI. FTIR spectroscopy showed the formation of new ester bonds between the PLA and PBAd parts, while analysis of the MP formulations showed no molecular drug-polyester matrix interactions. In vitro dissolution studies suggested a highly tunable biphasic extended release, for up to 30 days, indicating the potential of the synthesized copolymers to act as promising LAI formulations, which will maintain a continuous therapeutic level for an extended time period. Lastly, several empirical and mechanistic models were also tested, with respect to their ability to fit the experimental release data.

Poly(L-lactic acid) (PLLA) has been used as a biodegradable vascular scaffold (BVS) material due to high mechanical property, biodegradability, and biocompatibility. However, acidic byproducts from hydrolysis of PLLA reduce the pH after the surrounding implanted area and cause inflammatory responses. As a result, severe inflammation, thrombosis, and in-stent restenosis can occur after implantation by using BVS. Additionally, polymers such as PLLA could not find on X-ray computed tomography (CT) because of low radiopacity. To this end, here, we fabricated PLLA films as the surface of BVS and divided PLLA films into two coating layers. At the first layer, PLLA film was coated by 2,3,5-triiodobenzoic acid (TIBA) and magnesium hydroxide (MH) with poly(D,L-lactic acid) (PDLLA) for radiopaque and neutralization of acidic environment, respectively. The second layer of coated PLLA films is composed of polydopamine (PDA) and then cystamine (Cys) for the generation of nitric oxide (NO) release, which is needed for suppression of smooth muscle cells (SMCs) and proliferation of endothelial cells (ECs). The characterization of the film surface was conducted via various analyses. Through the surface modification of PLLA films, they have multifunctional abilities to overcome problems of BVS effectively such as X-ray penetrability, inflammation, thrombosis, and neointimal hyperplasia. These results suggest that the modification of biodegradable PLLA using TIBA, MH, PDA, and Cys will have important potential in implant applications.