Search

It is difficult to efficiently control nonlinear systems in the presence of uncertainty and disturbance (UAD). One of the main reasons derives from the negative impact of the unknown features of UAD as well as the response delay of the control system on the accuracy rate in the real time of the control signal. In order to deal with this, we propose a new controller named CO-FSMC for a class of nonlinear control systems subjected to UAD, which is constituted of a fuzzy sliding mode controller (FSMC) and a fuzzy-based compensator (CO). Firstly, the FSMC and CO are designed independently, and then an adaptive fuzzy structure is discovered to combine them. Solutions for avoiding the singular cases of the fuzzy-based function approximation and reducing the calculating cost are proposed. Based on the solutions, fuzzy sliding mode technique, lumped disturbance observer and Lyapunov stability analysis, a closed-loop adaptive control law is formulated. Simulations along with a real application based on a semi-active train-car suspension are performed to fully evaluate the method. The obtained results reflected that vibration of the chassis mass is insensitive to UAD. Compared with the other fuzzy sliding mode control strategies, the CO-FSMC can provide the best control ability to reduce unwanted vibrations., (Copyright © 2017 ISA. Published by Elsevier Ltd. All rights reserved.)

Plastic worm wheel is widely used in the vehicle manufacturing field because it is favorable for weight lightening, vibration and noise reduction, as well as corrosion resistance. However, it is very difficult for general plastics to secure the mechanical properties that are required for vehicle gears. If the plastic resin is reinforced by glass fiber in the fabrication process of plastic worm wheel, it is possible to achieve the mechanical properties of metallic material levels. In this study, the mechanical characteristic analysis of the glass-reinforced plastic worm wheel, according to the contents of glass fiber, is performed by analytic and experimental methods. In the case of the glass fiber-reinforced resin, the orientation and contents of glass fibers can influence the mechanical properties. For the characteristic prediction of plastic worm wheel, computer-aided engineering (CAE) analysis processes such as structural and injection molding analysis were executed with the polyamide resin reinforcement glass fiber (25 wt %, 50 wt %). The injection mold for fabricating the prototype plastic worm wheel was designed and made to reflect the CAE analysis results. Finally, the durability of prototype plastic worm wheel fabricated by the injection molding process was evaluated by the experimental method and the characteristics according to the glass fiber contents.

For microfabrications of biochips with micro fluidic channels, a large number of microfabrication techniques based on silicon or glass-based Micro-Electro-Mechanical System (MEMS) technologies were proposed in the last decade. In recent years, for low cost and mass production, polymer-based microfabrication techniques by microinjection molding and micro hot embossing have been proposed. These techniques, which require a proper photoresist, mask, UV light exposure, developing, and electroplating as a preprocess, are considered to have some problems. In this study, we propose a new microfabrication technology which consists of micro end-milling and powder blasting. This technique could be directly applied to fabricate the metal mold without any preprocesses. The metal mold with micro-channels is machined by micro end-milling, and then, burrs generated in the end-milling process are removed by powder blasting. From the experimental results, micro end-milling combined with powder blasting could be applied effectively for fabrication of the injection mold of biochips with micro fluidic channels.

Micro drilled holes are utilized in many of today's fabrication processes.Precision production processes in industries are trending toward the use of smaller holeswith higher aspect ratios, and higher speed operation for micro deep hole drilling. However,undesirable characteristics related to micro drilling such as small signal-to-noise ratios,wandering drill motion, high aspect ratio, and excessive cutting forces can be observedwhen cutting depth increases. In this study, the authors attempt to minimize the thrustforces in the step-feed micro drilling process by application of the DOE (Design ofExperiment) method. Taking into account the drilling thrust, three cutting parameters,feedrate, step-feed, and cutting speed, are optimized based on the DOE method. Forexperimental studies, an orthogonal array L 27 (3 13 ) is generated and ANOVA (Analysis ofVariance) is carried out. Based on the results it is determined that the sequence of factorsaffecting drilling thrusts corresponds to feedrate, step-feed, and spindle rpm. Acombination of optimal drilling conditions is also identified. In particular, it is found in thisstudy that the feedrate is the most important factor for micro drilling thrust minimization.

Recently, the magnetorheological (MR) polishing process has been examined asa new ultra-precision polishing technology for micro parts in MEMS applications. In theMR polishing process, the magnetic force plays a dominant role. This method uses MRfluids which contains micro abrasives as a polishing media. The objective of the presentresearch is to shed light onto the material removal mechanism under various slurryconditions for polishing and to investigate surface characteristics, including shape analysisand surface roughness measurement, of spots obtained from the MR polishing process usingalumina abrasives. A series of basic experiments were first performed to determine theoptimum polishing conditions for BK7 glass using prepared slurries by changing the processparameters, such as wheel rotating speed and electric current. Using the obtained results,groove polishing was then performed and the results are investigated. Outstanding surfaceroughness of Ra=3.8nm was obtained on the BK7 glass specimen. The present resultshighlight the possibility of applying this polishing method to ultra-precision micro partsproduction, especially in MEMS applications.