Search

The effect of variations in Nb, Ta, and Ti concentrations in exchange for Al on the oxidation resistance of a new polycrystalline Ni-based superalloy (C19) was studied in air at 800 °C for up to 1000 h. An external scale of Ti-doped Cr 2 O 3 and a sub-scale of discontinuous Al 2 O 3 intrusions formed on the surface of all the studied alloys. Contrary to other reports, increasing the Nb concentration improved the oxidation performance and may have promoted the formation of a CrTaO 4 layer, thereby reducing oxygen ingress. The addition of Ta also significantly improved oxidation resistance and reduced the depth of the Al 2 O 3 intrusions. Increasing the Ti concentration did not significantly affect the oxidation performance, potentially due to the relatively low Ti concentrations investigated. Several of the studied alloys with modified Ta and Ti concentrations showed regions of continuous Al 2 O 3 scale formation, suggesting that the compositions are in a transition regime between Cr 2 O 3 -forming and Al 2 O 3 -forming behaviour. The findings suggested that part of the Ti content in C19 could potentially be replaced with Nb, Ta and/or other elements to further enhance oxidation resistance and other desirable properties. Overall, the insights gained could serve as a guide to optimise the composition of C19 and similar alloys for enhanced oxidation resistance., Supplementary Information: The online version contains supplementary material available at 10.1007/s11085-023-10218-7., Competing Interests: Conflict of interestThe authors declare that they have no conflict of interest., (© The Author(s) 2024.)

The use of inoculants added to precursor powder is a method of influencing grain growth during fabrication. Niobium carbide (NbC) particles have been added to IN718 gas atomised powder for additive manufacturing via laser-blown-powder directed-energy-deposition (LBP-DED). The collected data in this study reveals the effects of the NbC particles on the grain structure, texture and elastic properties, and oxidative properties of LBP-DED IN718 in the As-DED and heat-treated conditions. The microstructure was investigated using X-ray diffraction (XRD), scanning electron microscopy (SEM) coupled with electron backscattered diffraction (EBSD), and transmission electron microscopy (TEM) coupled with energy dispersive X-ray spectroscopy (EDS). Resonant ultrasound spectroscopy (RUS) was used to measure the elastic properties and phase transitions during standard heat treatments. Thermogravimetric analysis (TGA) is used to probe the oxidative properties at 650°C., Competing Interests: The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: This work was funded by the EPSRC (through an iCase studentship) and by Rolls-Royce plc., (© 2023 The Author(s).)

An assessment is made of the Wagner transition criteria for predicting the formation of a continuous Al 2 O 3 scale in Ni-based superalloys. Predictions are compared with data from an experimental Ni-based superalloy as well as commercial superalloys for which published data are available. The methodology was generally successful in predicting the transition temperature of the commercial superalloys but underpredicted the transition temperature of the experimental superalloy by approximately 50-100 °C. The difference in the transition temperature of the experimental superalloy to form a continuous Al 2 O 3 scale is primarily attributed to a complex oxide subscale that increased the internal volume fraction of oxide and led to reduced oxygen ingress. The sensitivity and limitations of the methodology are discussed, and recommendations are made to refine the methodology to facilitate the interpretation of oxidation behaviour in polycrystalline Ni-based superalloys., Supplementary Information: The online version contains supplementary material available at 10.1007/s11085-023-10163-5., Competing Interests: Conflict of interestThe authors declare that they have no conflict of interest., (© The Author(s) 2023.)

The additive manufacturing (AM) of components through laser-blown-powder directed-energy-deposition (LBP-DED) is highly applicable to the repair of aerospace components. Fabrication of superalloys with this technique, as with other AM methods, often encounters complications that include the formation of undesired phases, irregular microstructure and texture leading to anisotropic elastic properties. Heat treatments and other post-processing techniques can be used to mitigate these issues. The collected data demonstrates the effects of different heat treatment protocols on the microstructure, elastic properties, and hardness of LBP-DED IN718. In this study eight different heat treatment were used to investigate the effects of treatment time and temperature. The microstructure was investigated through SEM, with XRD and EDX used for phase analysis. The texture was characterised using SEM coupled with EBSD and the elastic properties were determined from resonant ultrasound spectroscopy., Competing Interests: The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: This work was funded by the EPSRC (through and iCase studentship) and by Rolls-Royce plc., (© 2021 Published by Elsevier Inc.)

Refractory metal high-entropy superalloys (RSA), which possess a nanoscale microstructure of B2 and bcc phases, have been developed to offer high temperature capabilities beyond conventional Ni-based alloys. Despite showing a number of excellent attributes, to date there has been little consideration of their microstructural stability, which is an essential feature of any material employed in high temperature service. Here, the stability of the exemplar RSA AlMo 0.5 NbTa 0.5 TiZr is studied following 1000 h exposures at 1200, 1000 and 800 °C. Crucially, the initial nanoscale cuboidal B2 + bcc microstructure was found to be unstable following the thermal exposures. Extensive intragranular precipitation of a hexagonal Al-Zr-rich intermetallic occurred at all temperatures and, where present, the bcc and B2 phases had coarsened and changed morphology. This microstructural evolution will concomitantly change both the mechanical and environmental properties and is likely to be detrimental to the in-service performance of the alloy.

The new long duration experiment facility on beamline I11 at Diamond Light Source has been used to study the kinetics of sigma phase formation in three Cr-Co-Ni alloys. Diffraction data acquired during in situ exposure at 800°C for 50 d showed progressive increases in the sigma fraction. This was accompanied by changes in the proportions of the other phases, which differed markedly between the alloys studied. These results demonstrate the capabilities of the long duration facility for the study of metallurgical phenomena over periods of months to years, a capability not previously available at a synchrotron source., (open access.)

The data presented in this article are related to the research article entitled "a new beta titanium alloy system reinforced with superlattice intermetallic precipitates" (Knowles et al., 2018) [1]. This includes data from the as-cast alloy obtained using scanning electron microscopy (SEM) and x-ray diffraction (XRD) as well as SEM data in the solution heat treated condition. Transmission electron microscopy (TEM) selected area diffraction patterns (SADPs) are included from the alloy in the solution heat treated condition, as well as the aged condition that contained < 100 nm B2 TiFe precipitates [1], the latter of which was found to exhibit double diffraction owing to the precipitate and matrix channels being of a similar width to the foil thickness (Williams and Carter, 2009) [2]. Further details are provided on the macroscopic compression testing of small scale cylinders. Of the micropillar deformation experiment performed in [1], SEM micrographs of focused ion beam (FIB) prepared 2 µm micropillars are presented alongside those obtained at the end of the in-situ SEM deformation as well as videos of the in-situ deformation. Further, a table is included that lists the Schmidt factors of all the possible slip systems given the crystal orientations and loading axis of the deformed micropillars in the solution heat treated and aged conditions.

The data presented in this article are related to the research article entitled "Laves phase intermetallic matrix composite in situ toughened by ductile precipitates" (Knowles et al.) [1]. The composite comprised a Fe 2 (Mo, Ti) matrix with bcc (Mo, Ti) precipitated laths produced in situ by an aging heat treatment, which was shown to confer a toughening effect (Knowles et al.) [1]. Here, details are given on a focused ion beam (FIB) slice and view experiment performed on the composite so as to determine that the 3D morphology of the bcc (Mo, Ti) precipitates were laths rather than needles. Scanning transmission electron microscopy (S(TEM)) micrographs of the microstructure as well as energy dispersive X-ray spectroscopy (EDX) maps are presented that identify the elemental partitioning between the C14 Laves matrix and the bcc laths, with Mo rejected from the matrix into laths. A TEM selected area diffraction pattern (SADP) and key is provided that was used to validate the orientation relation between the matrix and laths identified in (Knowles et al.) [1] along with details of the transformation matrix determined.

The rafting of monocrystalline Ni- and Co-based superalloys has been studied by neutron diffractometry. Lattice parameter misfit values and the difference in phase stiffnesses at room temperature, 650 ° C , and 900 ° C are presented. These microstructural parameters should assist in refining computer models that aim to predict precipitate evolution in superalloys and aid future alloy design. The nature of rafting is shown experimentally to be dependent upon the lattice parameter misfit. The 900 ° C yield strength of the γ -phase of the Co-based superalloy with a rafted microstructure occurs at ~ 100 M P a , when loaded at a low strain rate.

Monoclonal antibodies to guinea pig T cells and antibodies to guinea pig immunoglobulin G were used in immunofluorescence studies to identify T and B cells in central nervous system tissue from guinea pigs with acute autoimmune encephalomyelitis. T cells appeared before B cells and were distributed within the white matter parenchyma, while B cells remained in perivascular spaces.

Phytochrome destruction begins immediately following actinic irradiation of 4-day-old, dark-grown oat (Avena sativa L., cv. Garry) shoots grown in open containers. When grown in closed containers, otherwise identical oat shoots exhibit a delay of about 40 minutes between irradiation and the onset of destruction. This delay can be attributed to accumulation of ethylene by several criteria, including elimination of the delay by mercuric perchlorate. These data provide an explanation for otherwise contradictory observations concerning the presence of a delay prior to the onset of destruction.

Both the red-absorbing (Pr) and far red-absorbing (Pfr) forms of phytochrome undergo destruction, defined as the loss of photoreversibly detectable chromoprotein following actinic irradiation of dark-grown tissue, in 4-day-old etiolated oat seedlings. Pr and Pfr destruction follow the same time course, exhibit the same time delay after actinic irradiation when the plants are grown in sealed containers, result in a loss of antigenically detectable phytochrome, as determined by radial immunodiffusion assay, equal to the loss of spectrophotometrically detectable phytochrome, and have the same sensitivity to 2-mercaptoethanol and azide. We suggest that Pr destruction is a consequence of the same mechanism that is responsible for Pfr destruction.