Search

In this work, a hydrometallurgical process for the recycling of diamond core drilling crowns by means of aqua regia leaching and subsequent alkali leaching was investigated. This investigation continues a previous study in which nitric acid was used for the acid leaching phase. In the current study, higher tungsten recovery was achieved, reaching 98.2%, which is an improvement of about 1.5%. Another advancement of this study was the high Co recovery (97.21%) and the high purity of the tungsten trioxide obtained, comparable to the previously proposed technological process. Furthermore, a novel laboratory method for testing recycled diamond drilling crowns based on infrared thermography was introduced. Although this innovative approach is not the most accurate, it is fast and cost-effective and provides valuable results before the actual field test is conducted as a final evaluation. In addition, the infrared thermography method offers the advantage of non-destructive testing, ensuring that the diamond drilling crowns can be assessed without compromising their structural integrity. Other instrumental methods used to characterize the products and intermediates were X-ray diffraction (XRD), scanning electron microscope with energy dispersive X-ray spectroscopy (SEM-EDS), and laser desorption ionization mass spectrometry (LDI-MS). The analytical method for the concentrations in all working solutions was ICP-AES.

This study is focused on the detailed examination of the combustion properties and kinetic analysis of a cellulose acetate fibrous bundle (CAFB), separated from used cigarette filters. It was shown that the faster rate of CAFB heating allows a large amount of heat to be supplied to a combustion system in the initial stages, where the increase in heating rate has a positive response to ignition behavior. The best combustion stability of CAFB is achieved at the lowest heating rate. Through the use of different kinetic methods, it was shown that combustion takes place through two series of consecutive reaction steps and one independent single-step reaction. By optimizing the kinetic parameters within the proposed reaction models, it was found that the steps related to the generation of levoglucosenone (LGO) (by catalytic dehydration of levoglucosan (LG)) and acrolein (by breakdown of glycerol during CAFB burning-which was carried out through glycerol adsorption on a TiO 2 surface in a the developed dehydration mechanism) represent rate-controlling steps, which are strongly controlled by applied heating rate. Isothermal predictions have shown that CAFB manifests very good long-term stability at 60 °C (which corresponds to storage in a sea shipping container), while at 200 °C, it shows a sudden loss in thermal stability, which is related to the physical properties of the sample.

Gold chloride clusters play an important role in catalysis and materials chemistry. Due to the diversity of their species and isomers, there is still a dearth of structural studies at the molecular level. In this work, anions of Au n Cl n+3 - and Au n Cl n+5 - (n = 2-4) clusters were obtained by laser desorption/ionization mass spectrometry (LDI MS), and the most stable isomers of Au n Cl n+3 - were determined after a thorough search and optimization at the TPSSh/aug-cc-pVTZ/ECP60MDF level. The results indicate that all isomers with the lowest energy have a planar zigzag skeleton. In each species, there is one Au(III) atom at the edge connected with four Cl atoms, which sets it from the other Au(I) atoms. Four growth pathways for Au n Cl n+3 - (n = 2-7) clusters are proposed (labelled R1, R2, R3 and R4). They are all associated with an aurophilic contact and are exothermic. The binding energies tend to stabilize at ∼ -41 kcal/mol when the size of the cluster increases in all pathways. The pathway R1, which connects all the most stable isomers of the respective clusters, is characterized by cluster growth due to aurophilic interactions at the terminal atom of Au(I) in the zigzag chains. In the pathway of R4 involving Au-Au bonding in its initial structures (n ≤ 3), the distance between intermediate gold atoms grows with cluster size, ultimately resulting in the transfer of the intermediate Au-Au bonding into aurophilic interaction. The size effect on the structure and aurophilic interactions of these clusters will be better understood based on these discoveries, potentially providing new insights into the active but elusive chemical species involved in the corresponding catalytic reactions or nanoparticle synthesis processes., Competing Interests: The authors declare that the research was conducted in the absence of any commercial or financial relationships that could be construed as a potential conflict of interest. The author(s) declared that they were an editorial board member of Frontiers, at the time of submission. This had no impact on the peer review process and the final decision., (Copyright © 2024 Xu, Liu, Hou, Kou, Xu, Veljković, Veličković and Kong.)

Nanoparticles (NPs), a distinct class of particles ranging in size from 1 to 100 nm, are one of the most promising technologies of the 21st century, and titanium dioxide NPs (TiO 2 NPs) are among the most widely produced and used NPs globally. The increased application of TiO 2 NPs raises concerns regarding their global safety and risks of exposure. Many animal studies have reported the accumulation of TiO 2 NPs in female reproductive organs; however, evidence of the resultant toxicity remains ambiguous. Since the surface area and chemical modifications of NPs can significantly change their cytotoxicity, we aimed to compare the toxic effects of pristine TiO 2 powder with surface-modified TiO 2 powders with salicylic acid (TiO 2 /SA) and 5-aminosalicylic acid (TiO 2 /5-ASA) on the ovaries, oviducts, and uterus on the 14th day following acute oral treatment. The results, based on alterations in food and water intake, body mass, organ-to-body mass ratio, hormonal status, histological features of tissues of interest, and antioxidant parameters, suggest that the modification with 5-ASA can mitigate some of the observed toxic effects of TiO 2 powder and encourage future investigations to create NPs that can potentially reduce the harmful effects of TiO 2 NPs while preserving their positive impacts.

The careful monitoring of patients with mild/moderate COVID-19 is of particular importance because of the rapid progression of complications associated with COVID-19. For prognostic reasons and for the economic management of health care resources, additional biomarkers need to be identified, and their monitoring can conceivably be performed in the early stages of the disease. In this retrospective cross-sectional study, we found that serum concentrations of high-mobility group box 1 (HMGB1) and heme oxygenase-1 (HO-1), at the time of hospital admission, could be useful biomarkers for COVID-19 management. The study included 160 randomly selected recovered patients with mild to moderate COVID-19 on admission. Compared with healthy controls, serum HMGB1 and HO-1 levels increased by 487.6 pg/mL versus 43.1 pg/mL and 1497.7 pg/mL versus 756.1 pg/mL, respectively. Serum HO-1 correlated significantly with serum HMGB1, oxidative stress parameters (malondialdehyde (MDA), the phosphatidylcholine/lysophosphatidylcholine ratio (PC/LPC), the ratio of reduced and oxidative glutathione (GSH/GSSG)), and anti-inflammatory acute phase proteins (ferritin, haptoglobin). Increased heme catabolism/hemolysis were not detected. We hypothesize that the increase in HO-1 in the early phase of COVID-19 disease is likely to have a survival benefit by providing protection against oxidative stress and inflammation, whereas the level of HMGB1 increase reflects the activity of the innate immune system and represents levels within which the disease can be kept under control.

Thioacetamide (TAA) is widely used to study liver toxicity accompanied by oxidative stress, inflammation, cell necrosis, fibrosis, cholestasis, and hepatocellular carcinoma. As an efficient free radical's scavenger, C60 fullerene is considered a potential liver-protective agent in chemically-induced liver injury. In the present work, we examined the hepatoprotective effects of two C60 doses dissolved in virgin olive oil against TAA-induced hepatotoxicity in rats. We showed that TAA-induced increase in liver oxidative stress, judged by the changes in the activities of SOD, CAT, GPx, GR, GST, the content of GSH and 4-HNE, and expression of HO-1, MnSOD, and CuZnSOD, was more effectively ameliorated with a lower C60 dose. Improvement in liver antioxidative status caused by C60 was accompanied by a decrease in liver HMGB1 expression and an increase in nuclear Nrf2/NF-κB p65 ratio, suggesting a reduction in inflammation, necrosis and fibrosis. These results were in accordance with liver histology analysis, liver comet assay, and changes in serum levels of ALT, AST, and AP. The changes observed in gut microbiome support detrimental effects of TAA and hepatoprotective effects of low C60 dose. Less protective effects of a higher C60 dose could be a consequence of its enhanced aggregation and related pro-oxidant role.

In the present study, we report the results of a detailed theoretical investigation along with the experimental observations of chlorine-doped small lithium clusters. The cluster ions of the type Li n Cl m + (n ≥ m, n = 1-6, m = 1-3) were obtained by the evaporation of LiCl from a Knudsen cell as a chemical reactor in the temperature range between 1800 and 2700 K. Heterogeneous clusters with more than one Cl atom are produced and detected for the first time, and the experimental conditions for formation and stability are examined. The structural characteristics and stabilities of neutral and positively charged Li n Cl m species are analyzed by using quantum chemistry methods. Doping lithium clusters with chlorine increases their stability, although there is a typical closed-shell-open-shell alternation in stability. Calculated dissociation energies are the best indicator of cluster stability of experimentally detected clusters. Heterogeneous lithium-chloride clusters can be viewed as species consisting of m negative Cl - ions and a positively charged Li n (1+,2+) "cage"; upon ionization, an electron departs from the lithium cage. An important reason for the higher stability of closed-shell clusters is the delocalization of electrons over the lithium cage, which is more energetically favored than localization of electrons between two lithium atoms. According to their ionization energies, the titled clusters can be classified as "superalkalis".

The theoretical calculations have predicted that nonmetal-doped potassium clusters can be used in the synthesis of a new class of charge-transfer salts which can be considered as potential building blocks for the assembly of novel nanostructured material. In this work, K(n)Cl (n = 2-6) and K(n)Cl(n-1) (n = 3 and 4) clusters were produced by vaporization of a solid potassium chloride salt in a thermal ionization mass spectrometry. The ionization energies (IEs) were measured, and found to be 3.64 ± 0.20 eV for K(2)Cl, 3.67 ± 0.20 eV for K(3)Cl, 3.62 ± 0.20 eV for K(4)Cl, 3.57 ± 0.20 eV for K(5)Cl, 3.69 ± 0.20 eV for K(6)Cl, 3.71 ± 0.20 eV for K(3)Cl(2) and 3.72 ± 0.20 eV for K(4)Cl(3). The K(n)Cl(+) (n = 3-6) clusters were detected for the first time in a cluster beam generated by the thermal ionization source of modified design. Also, this work is the first to report experimentally obtained values of IEs for K(n)Cl(+) (n = 3-6) and K(n)Cl(n-1) (+) (n = 3 and 4) clusters. The ionization energies for K(n)Cl(+) and K(n)Cl(n-1) (+) clusters are much lower than the 4.34 eV of the potassium atom; hence, these clusters should be classified as 'superalkali' species., (Copyright © 2012 John Wiley & Sons, Ltd.)

Rationale: The very small clusters of the type K(n)F are of particular importance since their first ionization energies (IEs) are lower than those of the alkali metal atoms. Theoretical calculation has demonstrated that this kind of cluster represents a potential 'building block' for cluster-assembly materials with unique structural, electronic, optical, magnetic, and thermodynamic properties. To date, however, there have been no experimental results on the IEs of K(n)F (n >2) clusters., Method: K(n)F (n = 2-6) clusters were produced by the evaporation of a solid potassium fluoride salt using a modified thermal ionization source of modified design, and mass selected by a magnetic sector mass spectrometer where their IEs were determined., Results: Clusters K(n)F (n = 3-6) were detected for the first time. The order of the ion intensities was K(2)F(+)> > K(4)F(+)> > K(3)F(+)K(6)F(+)> K(5)F(+). The determined IEs were 3.99 ± 0.20 eV for K(2)F, 4.16 ± 0.20 eV for K(3)F, 4.27 ± 0.20 eV for K(4)F, 4.22 ± 0.20 eV for K(5)F, and 4.31 ± 0.20 eV for K(6)F. The IEs of K(n)F increase slightly with the increase in potassium atom number from 2 to 6. We also observed that the presence of a fluorine atom leads to increasing ionization energy of bare metal potassium clusters., Conclusions: The modified thermal ionization source provides an efficient way of obtaining the fluorine-doped potassium clusters. These results also present experimental proof that K(n)F (n = 2-6) clusters belong to the group of 'superalkali' species., (Copyright © 2012 John Wiley & Sons, Ltd.)

Clusters of the type Li(n)X (X = halides) can be considered as potential building blocks of cluster-assembly materials. In this work, Li(n)Br (n = 2-7) clusters were obtained by a thermal ionization source of modified design and selected by a magnetic sector mass spectrometer. Positive ions of the Li(n)Br (n = 4-7) cluster were detected for the first time. The order of ion intensities was Li(2)Br(+) > Li(4)Br(+) > Li(5)Br(+) > Li(6)Br(+) > Li(3)Br(+). The ionization energies (IEs) were measured and found to be 3.95 ± 0.20 eV for Li(2)Br, 3.92 ± 0.20 eV for Li(3)Br, 3.93 ± 0.20 eV for Li(4)Br, 4.08 ± 0.20 eV for Li(5)Br, 4.14 ± 0.20 eV for Li(6)Br and 4.19 ± 0.20 eV for Li(7)Br. All of these clusters have a much lower ionization potential than that of the lithium atom, so they belong to the superalkali class. The IEs of Li(n)Br (n = 2-4) are slightly lower than those in the corresponding small Li(n) or Li(n)H clusters, whereas the IEs of Li(n)Br are very similar to those of Li(n) or Li(n)H for n = 5 and 6. The thermal ionization source of modified design is an important means for simultaneously obtaining and measuring the IEs of Li(n)Br (n = 2-7) clusters (because their ions are hermodynamically stable with respect to the loss of lithium atoms in the gas phase) and increasingly contributes toward the development of clusters for practical applications., (Copyright © 2012 John Wiley & Sons, Ltd.)

Rationale: Theoretical calculations have shown that the first ionization energy of clusters of the type Li(n) Cl (n ≥2), with more than eight valent electrons, is lower than that of alkali metal atoms; hence they are named superalkali. Superalkali clusters can mimic the chemical behavior of alkali metals and may be used as building blocks of new cluster-assembled materials. There is currently no reliable experimental proof of this kind of clusters and such proof is required., Methods: The Li(n) Cl (n = 2-6) clusters were produced by a thermal ionization source of modified design, and mass selected by a magnetic-sector mass spectrometer. The modification pertains to the replacement of the side filaments by a cylinder in the triple-filament thermal ionization source. The sample, which is LiCl salt, was pressed into a ring and placed on the inner wall of the cylinder., Results: It was observed that the ions of clusters with an even number of lithium atoms (Li(2) Cl(+) , Li(4) Cl(+) , Li(6) Cl(+) ) are more stable than the odd-numbered ones (Li(5) Cl(+) , Li(3) Cl(+) ). The ionization energies were determined to be 3.98 ± 0.25 eV for Li(2) Cl, 4.10 ± 0.25 eV for Li(3) Cl, 3.90 ± 0.25 eV for Li(4) Cl, 4.01 ± 0.25 eV for Li(5) Cl, and 4.09 ± 0.25 eV for Li(6) Cl. The presence of a halogen atom reduces the ionization energy of the metal clusters., Conclusions: The thermal ionization source of modified design presents a suitable simple way to obtaining and measuring the ionization energies of very small lithium monochloride clusters. Clusters Li(n) Cl, n = 4 to 6, were detected for the first time., (Copyright © 2012 John Wiley & Sons, Ltd.)

The electronic structure and properties of dipotassiummonohalides are important for understanding the unique physical and chemical behavior of M(n)X systems. In the present study, K(2) X (here X=F, Cl, Br, I) clusters were generated in the vapor over salts of the corresponding potassium halide, using a magnetic sector thermal ionization mass spectrometer. The ionization energies obtained for K(2)F, K(2)Cl, K(2)Br, and K(2)I molecules were 3.82 ± 0.1 eV, 3.68 ± 0.1 eV, 3.95 ± 0.1 eV, and 3.92 ± 0.1, respectively. These experimental values of ionization energies for K(2) X (X=F, Br, and I) are presented for the first time. The ionization energy of K(2)Cl determined by thermal ionization corresponds to previous results obtained by photoionization mass spectrometry, and it agrees with the theoretical ionization energy calculated by the ab initio method. The presently obtained results support previous theoretical predictions that the excess electron in dipotassiummonohalide clusters is delocalized over two potassium atoms, which is characteristic for F-center clusters., (Copyright © 2011 John Wiley & Sons, Ltd.)