Search

The aim of this paper was to examine the effects of adding TiO 2 nanoparticles to cementitious compositions and partially substituting natural aggregates with recycled aggregates consisting of glass, brick, slag, or textolite, and to examine the material's ability to resist corrosion under the action of chloride ions existent in the environment that attack the steel reinforcement. The results show that the changes in the cementitious composite when it comes to the composition and microstructure influence the formation of the oxide passivating layer of the reinforcement. The addition of TiO 2 nanoparticles and recycled aggregates impacts the kinetics and corrosion mechanism of the reinforcement. An addition of 3% TiO 2 was found to be optimal for reinforcement protection. Electrochemical impedance spectroscopy confirmed the results obtained by open-circuit potential and linear polarization tests. The classification of favorable conditions indicates that compositions with recycled aggregates and 3% TiO 2 are the most effective, with compositions in which the natural aggregates were partially substituted with slag being the most effective.

The aim of this study is to analyze the effect of the addition of TiO 2 nanoparticles (NTs) on the physical and mechanical properties, as well as the microstructural changes, of cementitious composites containing partially substituted natural aggregates (NAs) with aggregates derived from the following four recycled materials: glass (RGA), brick (RGB), blast-furnace slag (GBA), and recycled textolite waste with WEEE (waste from electrical and electronic equipment) as the primary source (RTA), in line with sustainable construction practices. The research methodology included the following phases: selection and characterization of raw materials, formulation design, experimental preparation and testing of specimens using standardized methods specific to cementitious composite mortars (including determination of apparent density in the hardened state, mechanical strength in compression, flexure, and abrasion, and water absorption by capillarity), and structural analysis using specialized techniques (scanning electron microscopy (SEM) images and energy dispersive X-ray spectroscopy (EDS)). The analysis and interpretation of the results focused primarily on identifying the effects of NT addition on the composites. Results show a decrease in density resulting from replacing NAs with recycled aggregates, particularly in the case of RGB and RTA. Conversely, the introduction of TiO 2 nanoparticles resulted in a slight increase in density, ranging from 0.2% for RTA to 7.4% for samples containing NAs. Additionally, the introduction of TiO 2 contributes to improved compressive strength, especially in samples containing RTA, while flexural strength benefits from a 3-4% TiO 2 addition in all composites. The compressive strength ranged from 35.19 to 70.13 N/mm 2 , while the flexural strength ranged from 8.4 to 10.47 N/mm 2 . The abrasion loss varied between 2.4% and 5.71%, and the water absorption coefficient varied between 0.03 and 0.37 kg/m 2 m 0.5 , the variations being influenced by both the nature of the aggregates and the amount of NTs added. Scanning electron microscopy (SEM) images and energy dispersive X-ray spectroscopy (EDS) analysis showed that TiO 2 nanoparticles are uniformly distributed in the cementitious composites, mainly forming CSH gel. TiO 2 nanoparticles act as nucleating agents during early hydration, as confirmed by EDS spectra after curing.

This research approaches knowledge gaps related to the pickling process dynamic modelling (the lack of predictability and simplicity of existing models) and answers the practical need for a software tool to facilitate the optimum process operation (by delivering estimations of the optimum corrosion inhibitor addition, optimum pickling bath lifetime, corrosion rate dynamic evolution, and material mass loss). A decision-making tool, PickT, has been developed and verified with the help of measurements from two different pickling experiments, both involving steel in hydrochloric acid. The first round of experiments lasted 336 h (each pickling batch duration was 24 h) and Cetilpyridinium bromide (CPB) was the corrosion inhibitor in additions from 8% to 12%. The collected dataset served for the tool development and first verification. The second round of experiments lasted 10 h (each batch duration was 2 h) and involved metformin hydrochloride (MET) in additions between 3.3 g/L and 10 g/L. This dataset served to test the transferability of PickT to other operating conditions in terms of corrosion inhibitor type, additions, batch duration and pickling bath lifetime magnitude. In both cases PickT results are in accordance with experimental findings. The tool advantages consist of the straightforward applicability, the low amount of field data required for reliable forecasts and the accessibility for untrained professionals from the industry.

The use of waste from industrial activities is of particular importance for environmental protection. Fly ash has a high potential in the production of construction materials. In the present study, the use of fly ash in the production of geopolymer paste and the effect of Fe 2 O 3 , MgO and molarity of NaOH solution on the mechanical strength of geopolymer paste are presented. Samples resulting from the heat treatment of the geopolymer paste were subjected to mechanical tests and SEM, EDS and XRD analyses. Samples were obtained using 6 molar and 8 molar NaOH solution with and without the addition of Fe 2 O 3 and MgO. Samples obtained using a 6 molar NaOH solution where Fe 2 O 3 and MgO were added had higher mechanical strengths compared to the other samples.

The aim of this work is to obtain new materials with improved sound absorbing and thermal properties, using rigid or flexible polyurethane foam reinforced with recycled fir sawdust from wood processing as well as by optimizing their mixing ratio. In this respect, we prepared and characterized samples by mixing rigid polyurethane foam (RPUF)/flexible polyurethane foam (FPUF) with 0, 35, 40, 45, and 50 wt% fir sawdust (FS) with grains size larger than 2 mm. The samples were evaluated by cell morphology analysis, sound absorption, and thermal insulation performance. The obtained composite materials containing 50% sawdust have superior acoustic properties compared to those with 100% FPUF in the range of 420-1250 Hz. The addition of 35% and 50% FS in the FPUF matrix led to improved thermal insulation properties and decreased thermal insulation properties in the case of RPUF. The results show that the use of FS-based composites with the FPUF/RPUF matrix for sound absorption and thermal insulation applications is a desirable choice and could be applied as an alternative to conventional synthetic fiber-based materials and as a recycling method of waste wood.

This study presents the correct processing of Co-Cr alloys as a method of preserving the properties of the materials as-cast, and therefore they can be safely placed in contact with the oral cavity tissues as resistance frameworks. The basic materials analyzed in this study were five commercial Co-Cr dental alloys with different components obtained in three processing steps. The analysis of the electrochemical behavior at the surface of the Co-Cr alloys was performed by electrochemical measurements: impedance spectroscopy (EIS), open circuit electrical potential (OCP), and linear polarization (LP). In terms of validation, all five alloys had a tendency to generate a stable oxide layer at the surface. After the measurements and the graphical representation, the alloy that had a higher percentage of tungsten (W) and iron (Fe) in composition showed a higher tendency of anodizing. After the application of the heat treatment, the disappearance of the hexagonal phase was observed, with the appearance of new phases of type (A,B) 2 O 3 corresponding to some oxide compounds, such as Fe 2 O 3 , Cr 2 O 3 , (Cr,Fe) 2 O 3 , and CoMnO 3 . In conclusion, the processing of Co-Cr alloys by melting and casting in refractory molds remains a viable method that can support innovation, in the context of technology advance in recent years towards digitalization of the manufacturing process, i.e., the construction of prosthetic frameworks conducted by additive methods using Co-Cr powder alloy.

The current context provides, worldwide, the need to identify solutions for the thermal efficiency of constructions, through sustainable and innovative methods and products. A viable solution is to produce thermal insulating products by carding-folding technology, using natural fibres and recycled polyethylene terephthalate (rPET) and polyester (rPES) waste, converted to fibres. This paper presents experimental results obtained after testing several thermal insulation composite products produced using a mix of sheep wool, cellulose, rPET and rPES fibres. The results of the research demonstrate the thermal insulation properties but, at the same time, identify the benefits of using such materials on the quality of the air in the interior space (the ability to adjust humidity and reduce the concentration of harmful substances). At the same time, the advantages of using sheep wool composite mattresses concerning their resistance to insect attack is demonstrated when compared with ordinary thermal insulation materials. Finally, sensitivity elements of these composites are observed in terms of sensitivity to mould, and to contact with water or soil, drawing future research directions in the development of this type of materials.