Search

Different from the traditional frequency-mixing technique which employs a contacting transducer, the laser-induced acoustic nonlinear frequency-mixing detection technique utilizes a laser source to instigate crack motion and generate acoustic waves. Thus, apart from the temperature oscillation induced by the pump laser, the "basic temperature" originating from the probe laser can also influence the crack. This additional variable complicates the contact state of the crack, yielding a more diverse range of nonlinear acoustic signal attributes. In light of this, our study enhances the conventional opto-acoustic nonlinear frequency mixing experimental setup by integrating an independent heating laser beam. This modification isolates the impact of the "basic temperature" on crack width while also dialing down the probe laser power to mitigate its thermal effects. To amplify the sensitivity of crack detection, we deliberated on the optimal laser source parameters for this setup. Consequently, our revamped system, paired with fine-tuned parameters, captures nonlinear acoustic signals with an enriched feature set. This investigation can provide support for the non-contact opto-acoustic nonlinear frequency mixing technique in the detection and evaluation of micro-cracks., Competing Interests: Declaration of competing interest The authors declare the following financial interests/personal relationships which may be considered as potential competing interests: Chen-Yin NI reports financial support was provided by the Fundamental Research Funds for the Central Universities of China. Zhong-Hua SHEN reports financial support was provided by the National Natural Science Foundation of China. If there are other authors, they declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (Copyright © 2024. Published by Elsevier B.V.)

The Synthetic Aperture Focusing Technique (SAFT) is an imaging algorithm used in laser ultrasonics (LU) to visualise the appearance of defects. However, ultrasound excited by a pulsed laser has the characteristics of wide bandwidth and multi-mode directivity patterns, leading to common problems in the SAFT process, such as low utilisation of ultrasound information and possible artefacts. To solve these problems, a Multi-mode Time-domain SAFT (MMT-SAFT) algorithm is proposed in this paper. The influence of ultrasonic directivity is discussed according to the imaging depth range, and imaging with multiple LU modes is performed to reduce artefacts. Simulations and experimental results prove the feasibility of the MMT-SAFT algorithm, which not only presents a clearer image of the upper part of defects but also improves image quality compared with time-domain SAFT using a single ultrasonic mode. The proposed technique can provide feasible directions for laser ultrasonic defect imaging., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2022 The Author(s).)

Herein, we studied the increasing tendency of photoacoustic (PA) conversion efficiency of the Au/polydimethylsiloxane (PDMS) composite. The thickness of the Au layer was optimized by modeling the PA process based on the Drude-Lorentz model and finite element analysis method, and corresponding results were verified. The results showed that the optimal Au thickness of the Au/PDMS composite was 35 nm. Finally, the Au/PDMS composites were coated onto the surface of aluminum alloys, which improved the thermoelastic laser ultrasonic (LU) signals to near 100 times. Besides, the defect mapping was performed by thermoelastic LU signals with Au/PDMS coating and ablation LU signals without coating; the Pearson correlation coefficient was higher than 0.95. The application in the defect detection in metal could provide guides for nondestructive detection on metals by laser ultrasound.

The Laser Ultrasonic (LU) technique has been widely studied. Detected ultrasonic signals can be further processed using Synthetic Aperture Focusing Techniques (SAFTs), to detect and image internal defects. LU-based SAFT in frequency-domain (F-SAFT) is developed to visualize horizontal hole-type defects in aluminum. Bulk acoustic waves are non-destructively generated by irradiating a laser line-source, and detected using a laser Doppler vibrometer at a point away from the generation. The influence of this non-coincident generation-detection on the equivalent acoustic velocity used in the algorithm is studied via velocity mappings. Because the wide-band generation characteristic of the LU technique, frequency range selections in acoustic wave signals are implemented to increase Signal-to-Noise Ratio (SNR) and reconstruction speed. Results indicate that by using the LU F-SAFT algorithm, and incorporating optimizations such as velocity mapping and frequency range selection, small defects can be visualized in 3D with corrected locations and improved image quality., Competing Interests: The authors declare that they have no known competing financial interests or personal relationships that could have appeared to influence the work reported in this paper., (© 2021 The Authors.)