17 results on '"Test sample"'
Search Results
2. Cohesion and adhesion of a sealant joint subjected to compressive stress
- Author
-
Boháček, Adam, Brandtner, Michal, Šlanhof, Jiří, Boháček, Adam, Brandtner, Michal, and Šlanhof, Jiří
- Abstract
This article is devoted to the evaluation of the suitability of the use of sealants when applied to a cement-based material and its subsequent exposure to compressive stress. Aquapanel cement board is chosen as the underlying material. In general, cementitious materials are characterized by a high concentration of dust particles on the surface, which prevent the correct adhesion of the sealant to the substrate, and therefore their sealing is often problematic. The sealants presented in this research are selected based on the manufacturer's recommendations for suitability for sealing cement-based materials. Base plates are made from cement board, which are subsequently sealed according to the procedures established by the ČSN EN ISO 11432 standard. The samples produced in this way are then cycled and their resistance to pressure stress is subsequently tested. The results of the test performed in this way are evaluated by measuring and visually evaluating the adhesion and cohesion of the cemented joint. Based on the results, it is possible to recommend all of the tested sealants for sealing cementitious base materials that are exposed to compressive stress.
- Published
- 2023
3. Cohesion and adhesion of a sealant joint subjected to compressive stress
- Author
-
Boháček, Adam, Brandtner, Michal, Šlanhof, Jiří, Boháček, Adam, Brandtner, Michal, and Šlanhof, Jiří
- Abstract
This article is devoted to the evaluation of the suitability of the use of sealants when applied to a cement-based material and its subsequent exposure to compressive stress. Aquapanel cement board is chosen as the underlying material. In general, cementitious materials are characterized by a high concentration of dust particles on the surface, which prevent the correct adhesion of the sealant to the substrate, and therefore their sealing is often problematic. The sealants presented in this research are selected based on the manufacturer's recommendations for suitability for sealing cement-based materials. Base plates are made from cement board, which are subsequently sealed according to the procedures established by the ČSN EN ISO 11432 standard. The samples produced in this way are then cycled and their resistance to pressure stress is subsequently tested. The results of the test performed in this way are evaluated by measuring and visually evaluating the adhesion and cohesion of the cemented joint. Based on the results, it is possible to recommend all of the tested sealants for sealing cementitious base materials that are exposed to compressive stress.
- Published
- 2023
4. Report on noble gas isotopic compositions of the 1E and 2E samples: An example of noble gas analyses for small sample sizes
- Author
-
Nagao, Keisuke, Miura, Yayoi N., Okazaki, Ryuji, Osawa, Takahito, 長尾 敬介, 三浦 弥生, 岡崎 隆司, 大澤 崇人, Nagao, Keisuke, Miura, Yayoi N., Okazaki, Ryuji, Osawa, Takahito, 長尾 敬介, 三浦 弥生, 岡崎 隆司, and 大澤 崇人
- Abstract
Isotopic compositions and concentrations of noble gases were analyses for 1E and 2E samples. Two noble gas mass spectrometry systems were used for the analyses; MS-2 for total melting and stepwise heating experiments on samples weighing 8 to 32 mg, and MS-3 for laser heating using single or several grains weighing 3 to 40 micro g. The data suggest that the sample 1E has noble gases similar to those for type 6 ordinary chondrites, while noble gases in 2E resemble those of carbonaceous chondrite Allende (CV3). Based on the present results it can be concluded that; 1) for ordinary chondritic materials several mg of sample is enough to measure all noble gas isotopes, 2) for surface materials of asteroids which would contain large amounts of implanted solar noble gases, the analytical technique using laser heating is applicable to samples weighing several micro g or less, 3) noble gas isotopic compositions obtained by the technique of single grain analysis can separate grains of different meteoroids impacted asteroidal surface, and 4) histories of exposure to cosmic-rays as well as impact degassing for each grain can provide detailed erosion process occurring on the asteroidal surface., The Institute of Space and Astronautical Science Report SP
- Published
- 2015
5. Characterization of carbonaceous matter
- Author
-
Murae, Tatsushi, Ikeda, Eiji, 村江 達士, 池田 英二, Murae, Tatsushi, Ikeda, Eiji, 村江 達士, and 池田 英二
- Abstract
The test samples, 1B and 2B, delivered from ISAS were examined by microscopic laser Raman, microscopic FT-IR, and microscopic fluorescence spectrometry. The spectral data indicate that the sample 1B contains small amount of PAHs and that the sample 2B contains significant amount of carbonaceous matter that is closely related to that in Allende., The Institute of Space and Astronautical Science Report SP
- Published
- 2015
6. S[lc]m and G[lc]d isotopic measurements in test samples for the MUSES-C mission
- Author
-
Hidaka, Hiroshi, Yoneda, Shigekazu, 日高 洋, 米田 成一, Hidaka, Hiroshi, Yoneda, Shigekazu, 日高 洋, and 米田 成一
- Abstract
The procedures for separation of Sm and Gd by resin chemistry were established, and then Sm and Gd isotopic measurements in two test samples 1F and 2F were performed to study the exposure records. Significant isotopic deviations over the analytical accuracy were not observed in (Sm-149)-(Sm-150) and (Gd-157)-(Gd-158) of the two samples. The estimated neutron fluences of 1F and 2F were (0 +/- 2.2) x 10(exp 15) and (0.8 +/- 3.1) x 10(exp 15) n/cm(sup 2), respectively., The Institute of Space and Astronautical Science Report SP
- Published
- 2015
7. The influence of the production process on mechanical properties of rubber testing samples
- Author
-
Škrobák, Adam, Staněk, Michal, Maňas, David, Ovsík, Martin, Šenkeřík, Vojtěch, Řezníček, Martin, Škrobák, Adam, Staněk, Michal, Maňas, David, Ovsík, Martin, Šenkeřík, Vojtěch, and Řezníček, Martin
- Abstract
The article deals with the influence of production technology on mechanical properties of rubber testing samples. In practice, rubber testing samples are cut out from a compression molded sheet, also in case of testing of rubber compounds appointed for injection molding. However, the different way of the preparation of testing samples and the production itself may have a negative effect on the mechanical properties of the final product. Thus the article judges, to what extent the mechanical properties (tensile strength, extension, tear strength and microhardness) of testing samples from selected rubber materials are influenced by injection molding, and evaluates the possible divergence.
- Published
- 2014
8. The influence of the production process on mechanical properties of rubber testing samples
- Author
-
Škrobák, Adam, Staněk, Michal, Maňas, David, Ovsík, Martin, Šenkeřík, Vojtěch, Řezníček, Martin, Škrobák, Adam, Staněk, Michal, Maňas, David, Ovsík, Martin, Šenkeřík, Vojtěch, and Řezníček, Martin
- Abstract
The article deals with the influence of production technology on mechanical properties of rubber testing samples. In practice, rubber testing samples are cut out from a compression molded sheet, also in case of testing of rubber compounds appointed for injection molding. However, the different way of the preparation of testing samples and the production itself may have a negative effect on the mechanical properties of the final product. Thus the article judges, to what extent the mechanical properties (tensile strength, extension, tear strength and microhardness) of testing samples from selected rubber materials are influenced by injection molding, and evaluates the possible divergence.
- Published
- 2014
9. Контроль химического состава латуни литейной в чушках, используемой для изготовления запорной арматуры
- Author
-
Пивоварчик, А. А., Пивоварчик, Е. В., Пивоварчик, А. А., and Пивоварчик, Е. В.
- Abstract
В статье представлены результаты исследования химического состава латуни литейной марки ЛС, поставляемой отечественными и зарубежными поставщиками, а также химического состава латуни свинцовой марки ЛЦ40С, используемой для изготовления запорной арматуры, с использованием оптико-эмиссионных спектрометров различных моделей и растрового микроскопа. Установлено, что чушка, поставляемая отечественным поставщиком, по своему химическому составу соответствует химическому составу чушки литейной марки ЛС, в то время как в чушке, поставляемой зарубежными поставщиками, отмечается нарушение химического состава по некоторым основным элементам. Результаты проведенных исследований показали, что чушка, поставляемая всеми поставщиками, а также расплав, полученный при ее использовании, содержат в своем составе такие вредные примеси, как S, Bi и P в количестве 0,001%, 0,0017 и 0,0045% соответственно, что может привести к снижению технологических свойств изделий. Установлено, что использование эмиссионных спектрометров ARL 3460 и OBLF-QSW 750, а также растрового электронного микроскопа Tescan VEGA II LMU позволяет получать практически идентичные значения содержания основных элементов и примесей в чушках литейных и латуни свинцовой марки ЛЦ40С при проведении исследований по определению химического состава исследуемых материалов.
10. Modifikace upínací části zkušebního zařízení RUMUL Cracktronic 160
- Author
-
Mazal, Pavel, Hutař, Pavel, Mazal, Pavel, and Hutař, Pavel
- Abstract
Tato diplomová práce se zabývá konstrukčním návrhem nových upínacích čelistí zkušebního stroje RUMUL Cracktronic 160, který je používán v únavové laboratoři Ústavu konstruování FSI VUT v Brně. Očekávaným přínosem nového řešení je zpřesnění, zjednodušení a zrychlení upínání zkušebních vzorků. K vytvoření 3D modelu čelistí je použit parametrický modelář SolidWorks. Potřebné analýzy jsou provedeny pomocí MKP v systému ANSYS Workbench., This diploma thesis deals with the structural design of the chucking jaws for RUMUL Cracktronic 160 testing machine. This apparatus is used in the fatigue laboratory of Institute of Machine Design FME BUT. Simplification, speed improvement and better test sample griping are expected gains of the new clamping system. Solidworks system is used to create 3D model of the jaws. Stress analysis is created by Finite element method in ANSYS Workbench software.
11. Stanovení mechanických vlastností materiálů používaných pro 3D tisk
- Author
-
Sedlák, Josef, Sliwková, Petra, Sedlák, Josef, and Sliwková, Petra
- Abstract
Diplomová práce se zabývá zejména stanovením mechanických vlastností materiálů používaných pro 3D tisk (ABS, nylon a PLA). Normalizované vzorky, vyrobené pomocí 3D tiskárny s využitím aditivní metody Fused Deposition Modeling, byly následně použity pro mechanické zkoušky. Práce je rozšířena také o stanovení mechanických vlastností vzorků, zhotovených technologií Soft Tooling. Pro výrobu vzorků technologií Soft Tooling byly použity polyuretanové pryskyřice SG 2000 a SG 145. Jednotlivé materiály byly analyzovány pomocí mechanických zkoušek (zkouška tahem a zkouška tvrdosti). U materiálů zhotovených technologií 3D tisku byly rovněž stanoveny parametry integrity povrchu. Z jednotlivých zkoušek byly vybrány parametry (mez pevnosti v tahu, modul pružnosti v tahu, tažnost a tvrdost), které byly následně statisticky zpracovávány. Práce je ukončena zhodnocením dosažených výsledků, které byly porovnávány s hodnotami udávanými v materiálových listech., The thesis deals with the determination of mechanical properties of materials used for 3D printing (ABS, nylon and PLA). Standardized samples produced using a 3D printer using the Fused Deposition Modeling method were subsequently used for mechanical testing. The work is also extended to determine the mechanical properties of samples made by Soft Tooling. For the production of Soft Tooling samples, polyurethane resins SG 2000 and SG 145 were used. Individual materials were analyzed by mechanical tests (tensile test and hardness test). Surface integrity parameters have also been determined for 3D-printed materials. Parameters were selected from the individual tests (tensile strength, modulus of elasticity) ductility and hardness), which were subsequently statistically processed. The work is concluded by evaluating the results obtained, which were compared with the values given in material sheets.
12. Stanovení mechanických vlastností materiálů používaných pro 3D tisk
- Author
-
Sedlák, Josef, Sliwková, Petra, Sedlák, Josef, and Sliwková, Petra
- Abstract
Diplomová práce se zabývá zejména stanovením mechanických vlastností materiálů používaných pro 3D tisk (ABS, nylon a PLA). Normalizované vzorky, vyrobené pomocí 3D tiskárny s využitím aditivní metody Fused Deposition Modeling, byly následně použity pro mechanické zkoušky. Práce je rozšířena také o stanovení mechanických vlastností vzorků, zhotovených technologií Soft Tooling. Pro výrobu vzorků technologií Soft Tooling byly použity polyuretanové pryskyřice SG 2000 a SG 145. Jednotlivé materiály byly analyzovány pomocí mechanických zkoušek (zkouška tahem a zkouška tvrdosti). U materiálů zhotovených technologií 3D tisku byly rovněž stanoveny parametry integrity povrchu. Z jednotlivých zkoušek byly vybrány parametry (mez pevnosti v tahu, modul pružnosti v tahu, tažnost a tvrdost), které byly následně statisticky zpracovávány. Práce je ukončena zhodnocením dosažených výsledků, které byly porovnávány s hodnotami udávanými v materiálových listech., The thesis deals with the determination of mechanical properties of materials used for 3D printing (ABS, nylon and PLA). Standardized samples produced using a 3D printer using the Fused Deposition Modeling method were subsequently used for mechanical testing. The work is also extended to determine the mechanical properties of samples made by Soft Tooling. For the production of Soft Tooling samples, polyurethane resins SG 2000 and SG 145 were used. Individual materials were analyzed by mechanical tests (tensile test and hardness test). Surface integrity parameters have also been determined for 3D-printed materials. Parameters were selected from the individual tests (tensile strength, modulus of elasticity) ductility and hardness), which were subsequently statistically processed. The work is concluded by evaluating the results obtained, which were compared with the values given in material sheets.
13. Modifikace upínací části zkušebního zařízení RUMUL Cracktronic 160
- Author
-
Mazal, Pavel, Hutař, Pavel, Mazal, Pavel, and Hutař, Pavel
- Abstract
Tato diplomová práce se zabývá konstrukčním návrhem nových upínacích čelistí zkušebního stroje RUMUL Cracktronic 160, který je používán v únavové laboratoři Ústavu konstruování FSI VUT v Brně. Očekávaným přínosem nového řešení je zpřesnění, zjednodušení a zrychlení upínání zkušebních vzorků. K vytvoření 3D modelu čelistí je použit parametrický modelář SolidWorks. Potřebné analýzy jsou provedeny pomocí MKP v systému ANSYS Workbench., This diploma thesis deals with the structural design of the chucking jaws for RUMUL Cracktronic 160 testing machine. This apparatus is used in the fatigue laboratory of Institute of Machine Design FME BUT. Simplification, speed improvement and better test sample griping are expected gains of the new clamping system. Solidworks system is used to create 3D model of the jaws. Stress analysis is created by Finite element method in ANSYS Workbench software.
14. Modifikace upínací části zkušebního zařízení RUMUL Cracktronic 160
- Author
-
Mazal, Pavel, Hutař, Pavel, Mazal, Pavel, and Hutař, Pavel
- Abstract
Tato diplomová práce se zabývá konstrukčním návrhem nových upínacích čelistí zkušebního stroje RUMUL Cracktronic 160, který je používán v únavové laboratoři Ústavu konstruování FSI VUT v Brně. Očekávaným přínosem nového řešení je zpřesnění, zjednodušení a zrychlení upínání zkušebních vzorků. K vytvoření 3D modelu čelistí je použit parametrický modelář SolidWorks. Potřebné analýzy jsou provedeny pomocí MKP v systému ANSYS Workbench., This diploma thesis deals with the structural design of the chucking jaws for RUMUL Cracktronic 160 testing machine. This apparatus is used in the fatigue laboratory of Institute of Machine Design FME BUT. Simplification, speed improvement and better test sample griping are expected gains of the new clamping system. Solidworks system is used to create 3D model of the jaws. Stress analysis is created by Finite element method in ANSYS Workbench software.
15. Stanovení mechanických vlastností materiálů používaných pro 3D tisk
- Author
-
Sedlák, Josef, Sliwková, Petra, Černý, Martin, Sedlák, Josef, Sliwková, Petra, and Černý, Martin
- Abstract
Diplomová práce se zabývá zejména stanovením mechanických vlastností materiálů používaných pro 3D tisk (ABS, nylon a PLA). Normalizované vzorky, vyrobené pomocí 3D tiskárny s využitím aditivní metody Fused Deposition Modeling, byly následně použity pro mechanické zkoušky. Práce je rozšířena také o stanovení mechanických vlastností vzorků, zhotovených technologií Soft Tooling. Pro výrobu vzorků technologií Soft Tooling byly použity polyuretanové pryskyřice SG 2000 a SG 145. Jednotlivé materiály byly analyzovány pomocí mechanických zkoušek (zkouška tahem a zkouška tvrdosti). U materiálů zhotovených technologií 3D tisku byly rovněž stanoveny parametry integrity povrchu. Z jednotlivých zkoušek byly vybrány parametry (mez pevnosti v tahu, modul pružnosti v tahu, tažnost a tvrdost), které byly následně statisticky zpracovávány. Práce je ukončena zhodnocením dosažených výsledků, které byly porovnávány s hodnotami udávanými v materiálových listech., The thesis deals with the determination of mechanical properties of materials used for 3D printing (ABS, nylon and PLA). Standardized samples produced using a 3D printer using the Fused Deposition Modeling method were subsequently used for mechanical testing. The work is also extended to determine the mechanical properties of samples made by Soft Tooling. For the production of Soft Tooling samples, polyurethane resins SG 2000 and SG 145 were used. Individual materials were analyzed by mechanical tests (tensile test and hardness test). Surface integrity parameters have also been determined for 3D-printed materials. Parameters were selected from the individual tests (tensile strength, modulus of elasticity) ductility and hardness), which were subsequently statistically processed. The work is concluded by evaluating the results obtained, which were compared with the values given in material sheets.
16. Modifikace upínací části zkušebního zařízení RUMUL Cracktronic 160
- Author
-
Mazal, Pavel, Hutař, Pavel, Beran, Pavel, Mazal, Pavel, Hutař, Pavel, and Beran, Pavel
- Abstract
Tato diplomová práce se zabývá konstrukčním návrhem nových upínacích čelistí zkušebního stroje RUMUL Cracktronic 160, který je používán v únavové laboratoři Ústavu konstruování FSI VUT v Brně. Očekávaným přínosem nového řešení je zpřesnění, zjednodušení a zrychlení upínání zkušebních vzorků. K vytvoření 3D modelu čelistí je použit parametrický modelář SolidWorks. Potřebné analýzy jsou provedeny pomocí MKP v systému ANSYS Workbench., This diploma thesis deals with the structural design of the chucking jaws for RUMUL Cracktronic 160 testing machine. This apparatus is used in the fatigue laboratory of Institute of Machine Design FME BUT. Simplification, speed improvement and better test sample griping are expected gains of the new clamping system. Solidworks system is used to create 3D model of the jaws. Stress analysis is created by Finite element method in ANSYS Workbench software.
17. Vliv obalu elektrod na mechanické vlastnosti svaru
- Author
-
Kubíček, Jaroslav, Izák, Josef, Lukeštík, Filip, Kubíček, Jaroslav, Izák, Josef, and Lukeštík, Filip
- Abstract
Práce se zabývá problematikou ručního obloukového svařování obalenou elektrodou. Konkrétně složením obalů a jejich vlastnostmi. Literární studie se dále zabývá procesy při svařování, technologií a zkouškami svarů. V praktické části se vybraly tři elektrody s podobným chemickým složením čistého svarového kovu. Konkrétně elektroda s bazickým obalem Böhler FOX EV 47, s rutilovým obalem Lincoln electric Ferrod 165A a s kyselým obalem ESAB E-K 103. Posléze došlo k návrhu experimentů, kterými byla příčná tahová zkouška a pozorování makrostruktury. Elektrodami se svařily sady navržených zkušebních vzorků pro zkoušku tahem. Mechanické vlastnosti vyplývající z tahové zkoušky byly zpracovány a zhodnoceny. Dále bylo provedeno a zhodnoceno pozorování makrostruktury., The thesis deals with the issue of shielded metal arc welding with covered electrodes, specifically focusing on the composition of the coatings and their properties. The literature study further addresses welding processes, technology, and weld testing. In the practical part, three electrodes with similar chemical compositions of pure weld metal were selected: the Böhler FOX EV 47 electrode with a basic coating, the Lincoln Electric Ferrod 165A electrode with a rutile coating, and the ESAB E-K 103 electrode with an acidic coating. Subsequently, experiments were proposed, including a tensile test and macrostructure observation. The electrodes were used to weld sets of designed test samples for the tensile test. The mechanical properties resulting from the tensile test were processed and evaluated. Furthermore, the macrostructure observation was conducted and assessed.
Catalog
Discovery Service for Jio Institute Digital Library
For full access to our library's resources, please sign in.