Search

Chronic wounds; Infection biomarker; Myeloperoxidase; Colorimetry Ferides i lesions; Biomarcadors d'infecció; Mieloperoxidasa; Colorimetria Heridas crónicas; Biomarcador de infección; Mieloperoxidasa; Colorimetría Current procedures for the assessment of chronic wound infection are time-consuming and require complex instruments and trained personnel. The incidence of chronic wounds worldwide, and the associated economic burden, urge for simple and cheap point-of-care testing (PoCT) devices for fast on-site diagnosis to enable appropriate early treatment. The enzyme myeloperoxidase (MPO), whose activity in infected wounds is about ten times higher than in non-infected wounds, appears to be a suitable biomarker for wound infection diagnosis. Herein, we develop a single-component foldable paper-based device for the detection of MPO in wound fluids. The analyte detection is achieved in two steps: (i) selective immunocapture of MPO, and (ii) reaction of a specific dye with the captured MPO, yielding a purple color with increasing intensity as a function of the MPO activity in infected wounds in the range of 20-85 U/mL. Ex vivo experiments with wound fluids validated the analytic efficiency of the paper-based device, and the results strongly correlate with a spectrophotometric assay.

Synthetic 11 Å tobermorite (Ca5Si6O16(OH)2.4H2O) and its Al-substituted analogue are layer-lattice ion-exchangers with potential applications in nuclear and hazardous wastewater treatment. The present study reports the facile one-pot hydrothermal synthesis of an Al-tobermorite-rich cation-exchanger from a combination of paper recycling ash, post-consumer container glass, and lime, with compositional ratios of [Ca]/[Si + Al] = 0.81 and [Al]/[Si + Al] = 0.18. The reaction products were characterized by powder X-ray diffraction analysis, 29Si magic angle spinning nuclear magnetic resonance spectroscopy, and scanning electron microscopy. Hydrothermal processing in 4 M NaOH(aq) at 100 °C for 7 days yielded an Al-tobermorite-rich product that also contained katoite (Ca3Al2SiO12H8), portlandite (Ca(OH)2), calcite (CaCO3), and amorphous silicate gel. The hydrothermal product was found to have a Cs+ cation exchange capacity of 59 ± 4 meq 100 g−1 and selective Cs+ distribution coefficients (Kd) of 574 ± 13 and 658 ± 34 cm3 g−1 from solutions with molar ratios [Cs+]:[Na+] and [Cs+]:[Ca2+] of 1:100. In a batch sorption study at 20 °C, the uptakes of Pb2+, Cd2+, and Cs+ were determined to be 1.78 ± 0.04, 0.65 ± 0.06, and 0.36 ± 0.03 mmol g−1, respectively. The kinetics of Pb2+, Cd2+, and Cs+ removal were described by the pseudo-second-order rate model, which gave respective rate constants (k2) of 0.010, 0.027, and 1.635 g mmol−1 min−1, and corresponding correlation coefficients (R2) of 0.997, 0.996, and 0.999. The metal ion sorption properties of the tobermorite-rich product compared favorably with those of other waste-derived tobermorites reported in the literature. Potential strategies to improve the yield, crystallinity, and sorption characteristics of the product are discussed.

Although it is well-known that nitroaromatic compounds quench the fluorescence of different conjugated polymers and form colored Meisenheimer complexes with proper nucleophiles, the potential of paper as a substrate for those macromolecules can be further developed. This work undertakes this task, impregnating paper strips with a fluorene-phenylene copolymer with quaternary ammonium groups, a bisfluorene-based cationic polyelectrolyte, and poly(2-(dimethylamino)ethyl methacrylate) (polyDMAEMA). Cationic groups make the aforementioned polyfluorenes attachable to paper, whose surface possesses a slightly negative charge and avoid interference from cationic quenchers. While conjugated polymers had their fluorescence quenched with nitroaromatic vapors in a non-selective way, polyDMAEMA-coated papers had a visual response that was selective to 2,4,6-trinitrotoluene (TNT), and that could be easily identified, and even quantified, under natural light. Far from implying that polyfluorenes should be ruled out, it must be taken into account that TNT-filled mines emit vapors from 2,4-dinitrotoluene (DNT) and dinitrobenzene isomers, which are more volatile than TNT itself. Atmospheres with only 790 ppbv TNT or 277 ppbv DNT were enough to trigger a distinguishable response, although the requirement for certain exposure times is an important limitation., This work was carried out under the Project inpactus—innovative products and technologies from eucalyptus, Project No. 21874 funded by Portugal 2020 through European Regional Development Fund (ERDF) in the frame of COMPETE 2020 No. 246/AXIS II/2017. Finantial support from the Coimbra Chemistry Centre (CQC), which is supported by the Fundação para a Ciência e a Tecnologia (FCT) through the programs UID/QUI/00313/2020 and COMPETE is gratefully acknowledged.

Biomimetic actuators are typically constructed as functional bi- or multilayers, where actuating and resistance layers together dictate bending responses upon triggering by environmental stimuli. Inspired by motile plant structures, like the stems of the false rose of Jericho (Selaginella lepidophylla), we introduce polymer-modified paper sheets that can act as soft robotic single-layer actuators capable of hygro-responsive bending reactions. A tailored gradient modification of the paper sheet along its thickness entails increased dry and wet tensile strength and allows at the same time for hygro-responsiveness. For the fabrication of such single-layer paper devices, the adsorption behavior of a cross-linkable polymer to cellulose fiber networks was first evaluated. By using different concentrations and drying procedures fine-tuned polymer gradients throughout the thickness can be achieved. Due to the covalent cross-linking of polymer with fibers, these paper samples possess significantly increased dry and wet tensile strength properties. We furthermore investigated these gradient papers with respect to a mechanical deflection during humidity cycling. The highest humidity sensitivity is achieved using eucalyptus paper with a grammage of 150 g m⁻² modified with the polymer dissolved in IPA (~13 wt%) possessing a polymer gradient. Our study presents a straightforward approach for the design of novel hygroscopic, paper-based single-layer actuators, which have a high potential for diverse soft robotic and sensor applications.

Cancer is a major cause of mortality and morbidity worldwide. Detection and quantification of cancer biomarkers plays a critical role in cancer early diagnosis, screening, and treatment. Clinicians, particularly in developing countries, deal with high costs and limited resources for diagnostic systems. Using low-cost substrates to develop sensor devices could be very helpful. The interest in paper-based sensors with colorimetric detection increased exponentially in the last decade as they meet the criteria for point-of-care (PoC) devices. Cellulose and different nanomaterials have been used as substrate and colorimetric probes, respectively, for these types of devices in their different designs as spot tests, lateral-flow assays, dipsticks, and microfluidic paper-based devices (μPADs), offering low-cost and disposable devices. However, the main challenge with these devices is their low sensitivity and lack of efficiency in performing quantitative measurements. This review includes an overview of the use of paper for the development of sensing devices focusing on colorimetric detection and their application to cancer biomarkers. We highlight recent works reporting the use of paper in the development of colorimetric sensors for cancer biomarkers, such as proteins, nucleic acids, and others. Finally, we discuss the main advantages of these types of devices and highlight their major pitfalls., This research was funded by Portuguese Foundation for Science and Technology (FCT), under the scope of the strategic funding of UIDB/04469/2020 unit and through Mariana Carneiro PhD grant reference SFRH/BD/131959/2017., info:eu-repo/semantics/publishedVersion

Paper-based abrasive products are multilayer structures in which the first layer on the paper substrate is usually a latex barrier coating to prevent the migration of adhesive glue into the substrate. The high coat weight (10 g/m2) of latex barrier layers is a cause of environmental concerns. Hence, alternative materials that can provide the barrier function at lower coat weights are desired. In this work, microfibrillated cellulose (MFC) combined with poly(vinyl) alcohol (PVA) were explored as suitable alternatives to the current latex coatings. Barrier coating formulations containing PVA, MFC, and silica (SiO2) were developed and applied to a paper substrate using a rod coating method on a pilot scale. Coating quality and barrier performance were characterized using scanning electron microscope images, air permeance, surface roughness, water contact angle, KIT test, and oil Cobb measurements. The barrier coatings were also studied for adhesion to the subsequent coating layer. An optimal barrier function was achieved with the developed coatings at a low coat weight of ca. 3 g/m2. The adhesion of pure PVA and PVA-MFC barrier coatings to the subsequent coating layer was inadequate; however, silica addition was found to improve the adhesion.

Current research trends in oenology concerned with contemporary issues that are of outmost important for the success of the wine industry [...]

Flexible plastic substrates are widely used in printed electronics; however, they cause major climate impacts and pose sustainability challenges. In recent years, paper-based electronics has been studied to increase the recyclability and sustainability of printed electronics. The aim of this paper is to analyze the printability and performance of metal conductor layers on different paper-based substrates using both flexography and screen printing and to compare the achieved performance with that of plastic foils. In addition, the re-pulpability potential of the used paper-based substrates is evaluated. As compared to the common polyethylene terephthalate (PET) substrate, the layer conductivity on paper-based substrates was found to be improved with both the printing methods without having a large influence on the detail rendering. This means that a certain surface roughness and porosity is needed for the improved ink transfer and optimum ink behavior on the surface of the substrate. In the case of uncoated paper-based substrates, the conductivity and print quality decreased by preventing the formation of the proper and intimate ink-substrate contact during the ink transfer. Finally, the re-pulpability trials together with layer quality analysis detected very good, coated substrate candidates for paper-based printed electronics competing with or even outperforming the print quality on the reference PET foil.

The use of micro-/nanofibrillated celluloses (M/NFCs) is often considered for the enhancement of paper properties, while it is still challenging to use them in lower weight gain coatings. This work explores how they might be used on the paper surface to improve the printing quality. In this regard, M/NFCs were produced using different pre-treatment methods, including mechanical (m-MFC), enzymatic (e-MFC), TEMPO-mediated oxidation (t-NFC) and cationization (c-NFC), and uniform coating formulations were developed through the cooking of starch and M/NFCs simultaneously. The formulations, at 6–8% of total solid concentration, were applied to the paper surface by roll coating, resulting in a dry coating weight of 1.5 to 3 g/m2. Besides M/NFCs, other components such as starch betainate (a cationic starch ester; SB), Pluronics® (a triblock co-polymer), precipitated calcium carbonate (PCC) and betaine hydrochloride (BetHCl) were also used in the M/NFC-based coating formulations to observe their combined influence on the printing quality. The presence of M/NFCs improved the paper printing quality, which was further enhanced by the increase in cationic charge density due to the presence of BetHCl/SB, and also by Pluronics®. The cationic charge of c-NFC was also found to be effective for improving the gamut area and optical density of coated papers, whereas whiteness was often reduced due to the quenching of the brightening agent. BetHCl, on the other hand, improved the printing quality of the coated papers, even though it was more effective when combined with M/NFCs, PCC and Pluronics®, and also helped to retain paper whiteness This work was carried out under the Project inpactus -innovative products and technologies from eucalyptus, Project N.º 21874 funded by Portugal 2020 through European Regional Development Fund (ERDF) in the frame of COMPETE 2020 nº246/AXIS II/2017. Authors would like to thank the Coimbra Chemical Centre, which is supported by the Fundação para a Ciência e a Tecnologia (FCT), through the projects UID/QUI/00313/2020 and COMPETE. Authors would also like to thank the CIEPQPF-Strategic Research Centre Project UIDB/00102/2020, funded by the Fundação para a Ciência e Tecnologia (FCT). M.S. acknowledges the PhD grant BDE 03|POCI-01-0247-FEDER-021874. R.A. acknowledges the post-doc grant BPD 02|POCI-01-0247-FEDER-021874

(1) Background: The complexity, amount of time, and the large amount of resource required to perform gold-standard bacteria culture procedures makes it difficult to perform timely pathogenic analyses, especially in areas where such resources are not readily available. A paper-based biochemical analytical tool can potentially tackle problems economically in terms of time and convenience, potentially finding utility in applications where simple and timely detection of bacteria is necessary; (2) Methods: The utility of paper-based MTT-PMS strips was tested using a simple colorimetric analytical methodology; (3) Results: Sufficient evidence was obtained to suggest that the strips can potentially be used as a rapid and convenient early, alternative bacteria screening tool for a variety of applications; (4) Conclusions: The potential of strips for the rapid detection of bacteria compared to standard bacteria culture is a key advantage in certain clinical, agricultural, and environmental applications.

Tissue paper production frequently combines two main types of raw materials: cellulose fibers from renewable sources and polymer-based additives. The development of premium products with improved properties and functionalities depends on the optimization of both. This work focused on the combination of innovative experimental and computational strategies to optimize furnish. The main goal was to improve the functional properties of the most suitable raw materials for tissue materials and develop new differentiating products with innovative features. The experimental plan included as inputs different fiber mixtures, micro/nano fibrillated cellulose, and biopolymer additives, and enzymatic and mechanical process operations. We present an innovative tissue paper simulator, the SimTissue, that we have developed, to establish the correlations between the tissue paper process inputs and the end-use paper properties. Case studies with industrial interest are presented in which the tissue simulator was used to design tissue paper materials with different fiber mixtures, fiber modification treatments, micro/nano fibrillated cellulose, and biopolymer formulations, and to estimate tissue softness, strength, and absorption properties. The SimTissue was able to predict and optimize a broader range of formulations containing micro/nanocellulose fibers, biopolymer additives, and treated-fiber mixtures, saving laboratory and industrial resources.

The accelerated ageing of wood in terms of heating or iron rusting has a potential effect on the physio-mechanical, chemical and biological properties of wood. The effects of accelerated ageing on the mechanical, physical and fungal activity properties of some wood materials (Schinus terebinthifolius, Erythrina humeana, Tectona grandis, Pinus rigida and Juglans nigra) were studied after several cycles of heating and iron rusting. The fungal activity was assayed against the growth of Aspergillus terreus, Aspergillus niger, Fusarium culmorum and Stemphylium solani. In addition, the mechanical and optical properties of paper sheets produced from those wood pulps by means of Kraft cooking were evaluated. The mechanical and chemical properties of the studied wood species were affected significantly (p < 0.05) by the accelerated ageing, compared to control woods. With Fourier transform infrared (FTIR) spectroscopy, we detected an increase in the intensity of the spectra of the functional groups of cellulose in the heated samples, which indicates an increase in cellulose content and decrease in lignin content, compared to other chemical compounds. For pulp properties, woods treated by heating showed a decrease in the pulp yield. The highest significant values of tensile strength were observed in pulp paper produced from untreated, heated and iron-rusted P. rigida wood and they were 69.66, 65.66 and 68.33 N·m/g, respectively; we calculated the tear resistance from pulp paper of untreated P. rigida (8.68 mN·m2/g) and T. grandis (7.83 mN·m2/g) and rusted P. rigida (7.56 mN·m2/g) wood; we obtained the values of the burst strength of the pulp paper of untreated woods of P. rigida (8.19 kPa·m2/g) and T. grandis (7.49 kPa·m2/g), as well as the fold number of the pulp paper of untreated, heated and rusted woods from P. rigida, with values of 195.66, 186.33 and 185.66, respectively. After 14 days from the incubation, no fungal inhibition zones were observed. Accelerated ageing (heated or iron-rusted) produced significant effects on the mechanical and chemical properties of the studied wood species and affected the properties of the produced pulp paper.

Waste paper is often underutilized as a low-value recyclable resource and can be a potential source of cellulose nanofibers (CNFs) due to its rich cellulose content. Three different processes, low acid treatment, alkali treatment and bleaching treatment, were used to pretreat the waste paper in order to investigate the effect of different pretreatments on the prepared CNFs, and CNFs obtained from bleached pulp boards were used as control. All sample fibers were successfully prepared into CNFs by 2,2,6,6-tetramethyl-piperidine-1-oxyl (TEMPO) oxidation. It was quite obvious that the bleached CNFs samples showed dense fibrous structures on a scanning electron microscopy (SEM), while needle-like fibers with width less than 20 nm were observed on a transmission electron microscopy (TEM). Meanwhile, the bleaching treatment resulted in a 13.5% increase in crystallinity and a higher TEMPO yield (e.g., BCNF, 60.88%), but a decrease in thermal stability. All pretreated CNFs samples showed narrow particle size distribution, good dispersion stability (zeta potential less than −29.58 mV), good light transmission (higher than 86.5%) and low haze parameters (lower than 3.92%). This provides a good process option and pathway for scalable production of CNFs from waste papers.

Given the imperative of monitoring organophosphorus pesticides (OPs) residues in the ecosystem, here a novel, facile and sensitive fluorescence sensor is presented for the rapid detection of dimethoate. In this work, surface molecularly imprinted polymer (SMIP) and microfluidic technology had been introduced to enhance the selectivity and portability of the described methodology. Oil-soluble CdSe quantum dots (QDs) synthesized in a green way were used as fluorescent material for the selective detection of dimethoate on the basis of static quenching and photoinduced electron transfer mechanism. Among many kinds of paper materials, glass fiber paper was used as the novel substrate of paper chip due to low pristine fluorescence and better performance when combining CdSe QDs. In the process of molecular imprinting, the interaction between several functional monomers and dimethoate molecule was investigated and simulated theoretically by software to improve the selectivity of the sensor. Consequently, the fabricated novel detection platform could effectively respond to dimethoate in 10 min with the concentration range of 0.45–80 μmol/L and detection limit of 0.13 μmol/L. The recovery in the spiked experiment soybean sample was in an acceptable range (97.6–104.1%) and the accuracy was verified by gas chromatography-mass spectrometry, which signified the feasibility and potential in food sampling.

Label-free SERS is a powerful bio-analytical technique in which molecular fingerprinting is combined with localized surface plasmons (LSPs) on metal surfaces to achieve high sensitivity. Silver and gold colloids are among the most common nanostructured substrates used in SERS, but since protein-rich samples such as serum or plasma can hinder the SERS effect due to protein–substrate interactions, they often require a deproteinization step. Moreover, SERS methods based on metal colloids often suffer from a poor reproducibility. Here, we propose a paper-based SERS sampling method in which unprocessed human serum samples are first soaked on paper strips (0.4 × 2 cm2), and then mixed with colloidal silver nanoparticles by centrifugation to obtain a Centrifugal Silver Plasmonic Paper (CSPP). The CSPP methodology has the potential to become a promising tool in bioanalytical SERS applications: it uses common colloidal substrates but without the need for sample deproteinization, while having a good reproducibility both in terms of overall spectral shape (r > 0.96) and absolute intensity (RSD < 10%). Moreover, this methodology allows SERS analysis more than one month after serum collection on the paper strip, facilitating storage and handling of clinical samples (including shipping from clinical sites to labs).

Simple Summary Although secondary enucleation (SE) is the treatment of choice for retinoblastoma eyes that did not respond favorably to conservative therapies, clear criteria for its indication are, however, currently missing. In this position paper on behalf of the European Retinoblastoma Group (EURbG), we discuss the available literature on SE, including its influence on metastases rate and survival, and propose guidelines to assist decision-making to interrupt eye-preserving therapies depending on the availabilities of advanced diagnostic and therapeutic modalities. Absolute indications to SE may be restricted to eyes with refractory tumor activity resisting all salvage treatments or eyes under apparent tumor control but no visual potential and irreducible complications. In contrast, eyes with an obscured optic nerve head and/or ocular complications amenable to specific surgical or medical management can be considered relative indications, provided that appropriate follow-up can be implemented and that parents are fully aware of a residual risk. Abstract Secondary enucleation (SE) puts an irreversible end to eye-preserving therapies, whenever their prolongation is expected to violate the presumed state of metastatic grace. At present, it must be acknowledged that clear criteria for SE are missing, leading to empiric and subjective indications commonly related to disease progression or relapse, disease persistence masking the optic nerve head or treatment-related complications obscuring the fundus view. This absence of evidence-based consensus regarding SE is explained by the continuously moving frontiers of the conservative management as a result of diagnostic and therapeutic advances, as well as by the lack of studies sufficiently powered to accurately stratify the risk of metastasis in conservatively treated patients. In this position paper of the European Retinoblastoma Group (EURbG), we give an overview of the progressive shift in the indications for SE over the past decades and propose guidelines to assist decision-making with respect to when SE becomes imperative or recommended, with corresponding absolute and relative SE indications. Further studies and validation of biologic markers correlated with the risk of metastasis are expected to set more precisely the frontiers of conservative management and thus consensual criteria for SE in the future.

Urine bags are commonly used to collect urine samples from neonates. However, the sample can be contaminated by stool, or detachment of the bag due to body movement can lead to failure of the collection. A qualitative urine collection kit containing ten filter papers of 3.2 mm diameter was developed and clinically verified among 138 neonates. During a single diaper change (approximately 3 h), the rate of urine collection was calculated. Urine collection was considered to be successful if any filter paper in the urine collection sheet turned from blue to white. Of the 127 neonates who passed urine, 122 had a change in the filter paper. The urine collection rate was 96%, with changes in all 10 filter papers observed in 98 neonates (80%). Urine collection rate was not influenced by sex (p = 1.00), age at collection (p = 0.72), preterm birth (p = 1.00), low birth weight (p = 0.92), or fecal contamination (p = 1.00). The incidence of dermatitis was not higher than in the group in which urine bags were used (urine collection kit: 2/68 [3%]; urine bag: 5/68 [7%]; p = 0.44). Novel urine collection kits using filter paper can collect samples from neonates safely and with a high probability of success.

Drought is a key factor restricting plant survival, growth and development. The physiological parameters of plants are commonly used to determine the water status, in order to irrigate appropriately and save water. In this study, mulberry (Morus alba L.) and paper mulberry (Broussonetia papyrifera (L.) Vent.) seedlings were used as experimental materials, and four soil moisture treatments were set up for both plant species: 70–75% (CK: the control group, referred to as T0), 55–60% (T1: mild drought), 40–45% (T2: moderate drought), and 25–30% (T3: severe drought). The growth parameter of the plants was measured every two days from the onset of the treatment, the photosynthetic and electrophysiological parameters of the plants were measured every other week for a total of five times. The physiological responses and electrophysiological traits of leaves under different treatment levels were analyzed. The results showed that the photosynthetic and electrophysiological parameters could characterize the response of mulberry growth and development to soil water, and the growth and electrophysiological parameters could characterize the response of paper mulberry growth and development to soil water. Mild drought had no significant effects on the growth and development of mulberry and paper mulberry.

The unique structural and electrochemical properties of graphene oxide (GO) make it an ideal material for the fabrication of biosensing devices. Therefore, in the present study, graphene oxide nanoparticles modified paper electrodes were used as a low-cost matrix for the development of an amperometric DNA sensor. The graphene oxide was synthesized using the modified hummers method and drop cast on a screen-printed paper electrode (SPPE) to enhance its electrochemical properties. Further, the GO/SPPE electrode was modified with a 5′NH2 labeled ssDNA probe specific to the htrA gene of Orientia tsutsugamushi using carbodiimide cross-linking chemistry. The synthesized GO was characterized using UV-Vis, FTIR, and XRD. The layer-by-layer modification of the paper electrode was monitored via FE-SEM, cyclic voltammetry, and electrochemical impedance spectroscopy (EIS). The sensor response after hybridization with single-stranded genomic DNA (ssGDNA) of O. tsutsugamushi was recorded using differential pulse voltammetry (DPV). Methylene blue (1 mM in PBS buffer, pH 7.2) was used as a hybridization indicator and [Fe(CN)6]−3/−4 (2.5 mM in PBS buffer, pH 7.2) as a redox probe during electrochemical measurements. The developed DNA sensor shows excellent sensitivity (1228.4 µA/cm2/ng) and LOD (20 pg/µL) for detection of O. tsutsugamushi GDNA using differential pulse voltammetry (DPV).

The main aim of this work was the investigation of the possibility of replacing the heavy metallic meshes applied onto the composite structure in airplanes for lightning strike protection with a thin film of Tuball single-wall carbon nanotubes in the form of ultra-light, conductive paper. The Tuball paper studied contained 75 wt.% or 90 wt.% of carbon nanotubes and was applied on the top of carbon fibre reinforced polymer before fabrication of flat panels. First, the electrical conductivity, impact resistance and thermo-mechanical properties of modified laminates were measured and compared with the reference values. Then, flat panels with selected Tuball paper, expanded copper foil and reference panels were fabricated for lightning strike tests. The effectiveness of lightning strike protection was evaluated by using the ultrasonic phased-array technique. It was found that the introduction of Tuball paper on the laminates surface improved both the surface and the volume electrical conductivity by 8800% and 300%, respectively. The impact resistance was tested in two directions, perpendicular and parallel to the carbon fibres, and the values increased by 9.8% and 44%, respectively. The dynamic thermo-mechanical analysis showed higher stiffness and a slight increase in glass transition temperature of the modified laminates. Ultrasonic investigation after lightning strike tests showed that the effectiveness of Tuball paper is comparable to expanded copper foil.

Determination of cellulose degree of polymerization (DP) is one of the most commonly used methods in paper degradation studies, performed either by a standardized method using viscometry (as average degree of polymerization (DPv)) or size-exclusion chromatography (SEC) (as weight average molecular mass (Mw)). Due to the insolubility of papers with high lignin content in cupriethylenediamine (CED), such as groundwood papers, viscometric determination is not possible, therefore, pretreatment is required to allow subsequent dissolution of the papers. In this study, the pretreatment of historical papers containing groundwood with sodium chlorite in acetic acid was investigated, which enables dissolution of the paper samples in CED and determination of the cellulose average degree of polymerization by viscometry (DPv). Kappa number was determined to estimate the lignin content in the papers. The suitability of SEC UV-VIS analysis for determination of Mw in papers with high lignin content had been verified before it was used as a comparative method for viscometry. Using SEC, changes in the weight average molecular mass (Mw) of cellulose tricarbanilate (CTC) derivative during delignification were evaluated. The results indicate that no significant depolymerization occurred in the selected samples under the studied delignification conditions, which was additionally confirmed with determination of monosaccharides by ion chromatography. The results of the Mw determinations by SEC and DPv by viscometry are in good correlation, justifying the use of viscometry after chlorite/acetic acid pretreatment to determine the cellulose average degree of polymerization in historical papers with high lignin content.

The early diagnosis of Alzheimer’s disease (AD) remains a challenge for medical scientists worldwide, leading to a number of research efforts that focus on biosensor development for AD biomarkers. However, the application of these complicated biosensors is limited in medical diagnosis, due to the difficulties in robust sensing platform development, high costs, and the necessity for technical professionals. We successfully developed a robust straightforward manufacturing process for the fabrication of multi-chamber paper devices using the wax printing method and exploited it to detect amyloid beta 42 oligomers (AβO42, a significant biomarker of AD) using copper-enhanced gold nanoprobe colorimetric immunoblotting. Small hydrophilic reaction chambers could concentrate the target sample to the desired size to improve the sensing performance. The copper-enhanced gold nanoprobe immunoblot using the designed multi-chamber platform exhibited a highly sensitive performance with a limit of detection of 320 pg/mL by the naked eye and 23.7 pg/mL by a smartphone camera. This process from sensing manufacture to sensing conduction is simple to perform whenever medical technicians require time- and cost-savings, without complicated instruments or the need for technical professionals, making it feasible to serve as a diagnostic tool worldwide for the early monitoring of AD and scalable devices for the sensing application of various biomarkers in clinical settings.

Sustainability appears to be increasingly important to consumers. In order for companies to reach their sustainability targets and offer more environmentally friendly solutions to consumers, food producers and retailers have begun to change their packaging to more recyclable, bio-based and biodegradable packaging. This study evaluated the sensory characteristics of paper-based prototype packages developed for two product categories (biscuit and meat packages) using a trained sensory panel. Consumer liking, preference and purchase intent were assessed by 130 participants. For the biscuit packages, no significant differences were observed for the liking of any of the four dimensions assessed (appearance, design, feel or overall liking). However, consumer segmentation identified three relatively homogeneous groups of consumers exhibiting differences in the hedonic reaction to the three packages. For the meat packages, significant differences and preference were observed between the original and paper-based packages. For both categories, the purchase intent was low, indicating that further work needed to be done to improve several quality characteristics (e.g., design, size and strength of the package), which would lead to better consumer acceptability.

This paper describes the use of fused deposition modeling (FDM) printing to fabricate paper-based analytical devices (PAD) with three-dimensional (3D) features, which is termed as 3D-PAD. Material depositions followed by heat reflow is a standard approach for the fabrication of PAD. Such devices are primarily two-dimensional (2D) and can hold only a limited amount of liquid samples in the device. This constraint can pose problems when the sample consists of organic solvents that have low interfacial energies with the hydrophobic barriers. To overcome this limitation, we developed a method to fabricate PAD integrated with 3D features (vertical walls as an example) by FDM 3D printing. 3D-PADs were fabricated using two types of thermoplastics. One thermoplastic had a low melting point that formed hydrophobic barriers upon penetration, and another thermoplastic had a high melting point that maintained 3D features on the filter paper without reflowing. We used polycaprolactone (PCL) for the former, and polylactic acid (PLA) for the latter. Both PCL and PLA were printed with FDM without gaps at the interface, and the resulting paper-based devices possessed hydrophobic barriers consisting of PCL seamlessly integrated with vertical features consisting of PLA. We validated the capability of 3D-PAD to hold 30 μL of solvents (ethanol, isopropyl alcohol, and acetone), all of which would not be retained on conventional PADs fabricated with solid wax printers. To highlight the importance of containing an increased amount of liquid samples, a colorimetric assay for the formation of dimethylglyoxime (DMG)-Ni (II) was demonstrated using two volumes (10 μL and 30 μL) of solvent-based dimethylglyoxime (DMG). FDM printing of 3D-PAD enabled the facile construction of 3D structures integrated with PAD, which would find applications in paper-based chemical and biological assays requiring organic solvents.

This week I read a press release from the University Hospital of Brussels with the title "30% of hospitalised COVID-19 patients have a heart defect one year after acute illness" [...]. ispartof: DIAGNOSTICS vol:12 issue:8 ispartof: location:Switzerland status: published

International audience; Multidisciplinary management of worsening heart failure (HF) in the elderly improves survival. To ensure patients have access to adequate care, the current HF and French health authority guidelines advise establishing a clearly defined HF patient pathway. This pathway involves coordinating multiple disciplines to manage decompensating HF. Yet, recent registry data indicate that insufficient numbers of patients receive specialised cardiology care, which increases the risk of rehospitalisation and mortality. The patient pathway in France involves three key stages: presentation with decompensated HF, stabilisation within a hospital setting and transitional care back out into the community. In each of these three phases, HF diagnosis, severity and precipitating factors need to be promptly identified and managed. This is particularly pertinent in older, frail patients who may present with atypical symptoms or coexisting comorbidities and for whom geriatric evaluation may be needed or specific geriatric syndrome management implemented. In the transition phase, multi-professional post-discharge management must be coordinated with community health care professionals. When the patient is discharged, HF medication must be optimised, and patients educated about self-care and monitoring symptoms. This review provides practical guidance to clinicians managing worsening HF in the elderly.

This paper is aimed at investigating the usage of biosynthesized poly(3-hydroxybutyrate) (P(3-HB)) for a coating on pineapple leaf fiber paper (PLFP). For this purpose, (P(3-HB)) was produced by Rhodococcus pyridinivorans BSRT1-1, a highly potential P(3-HB) producing bacterium, with a weight-average molecular weight (Mw) of 6.07 × 10 −5 g/mol. This biosynthesized P(3-HB) at 7.5% (w/v) was then coated on PLFP through the dip-coating technique with chloroform used as a solvent. The respective coated PLFP showed that P(3-HB) could be well coated all over on the PLFP surface as confirmed by scanning electron microscopy (SEM) and Fourier transform infrared (FTIR) spectroscopy. The brightness and mechanical properties of PLFP could be improved by coating with biosynthesized P(3-HB) in comparison to commercially available P(3-HB) and non-coated PLFP. Furthermore, coating of P(3-HB) significantly increased the water drop penetration time on the surface of PLFP and was similar to that of the commercial P(3-HB) with the same content. The results showed that all the coated PLPF samples can be degraded under the soil burial test conditions. We have demonstrated that the P(3-HB) coated PLFP paper has the ability to prevent water drop penetration and could undergo biodegradation. Taken together, the P(3-HB) coated PLFP can be applied as a promising biodegradable paper packaging.

Simple Summary The usage of alfalfa (Medicago sativa L.) as a dietary protein source for ruminants in China is limited by forage quality and planting scale. Paper mulberry (Broussonetia papyrifera L., RY) has emerged as a new and representative high-protein woody forage resource for ruminants. However, information is less available regarding how substituting RY for alfalfa affect the fermentation and protein quality in total mixed ration (TMR) silages. This study evaluated ensiling characteristics, protein quality, and in vitro digestibility in TMR silages by mixing RY with alfalfa at different rations. The TMR were made with alfalfa and RY mixtures (36.0%), maize meal (35.0%), oat grass (10.0%), soybean meal (7.5%), brewers’ grain (5.0%), wheat bran (5.0%), premix (1.0%), and salt (0.5%) on a dry matter basis, respectively. The alfalfa and RY mixtures were made in the following ratios of dry matter: 36:0 (RY0), 27:9 (RY9), 18:18 (RY18), 9:27 (RY27), and 0:36 (RY36). The results showed that RY substitution had no adverse effect on fermentation quality and nutritional composition, but inhibited true protein degradation, while decreasing in vitro dry matter and crude protein digestibility. Therefore, RY and alfalfa mixtures at a ratio of 18:18 is suitable for silage-based TMR. Abstract To develop an alternative high-protein forage resource to alleviate ruminant feed shortages, we investigated the effects of replacing alfalfa (Medicago sativa L.) with different ratios of paper mulberry (Broussonetia papyrifera L., RY) on fermentation quality, protein degradation, and in vitro digestibility of total mixed ration (TMR) silage. The TMR were made with alfalfa and RY mixtures (36.0%), maize meal (35.0%), oat grass (10.0%), soybean meal (7.5%), brewers’ grain (5.0%), wheat bran (5.0%), premix (1.0%), and salt (0.5%) on a dry matter basis, respectively. The alfalfa and RY mixtures were made in the following ratios of dry matter: 36:0 (RY0), 27:9 (RY9), 18:18 (RY18), 9:27 (RY27), and 0:36 (RY36). After ensiling for 7, 14, 28, and 56 days, fermentation quality, protein degradation, and microbial counts were examined, and chemical composition and in vitro digestibility were analyzed after 56 days of ensiling. All TMR silages, irrespective of the substitution level of RY, were well preserved with low pH and ammonia nitrogen content, high lactic acid content, and undetectable butyric acid. After ensiling, the condensed tannin content for RY18 silages was higher than the control, but non-protein nitrogen, peptide nitrogen, and free amino acid nitrogen contents was lower, while the fraction B1 (buffer-soluble protein) was not different among all the silages. Dry matter and crude protein digestibility for RY27 and RY36 silages was lower than the control, but there was no difference between control and RY18 silages. This study suggested that ensiling RY with alfalfa inhibited true protein degradation, but decreased in vitro dry matter and crude protein digestibility of TMR silages, and that 18:18 is the optimal ratio.

Escherichia coli has been known to cause a variety of infectious diseases. The conventional enzyme-linked immunosorbent assay (ELISA) is a well-known method widely used to diagnose a variety of infectious diseases. This method is expensive and requires considerable time and effort to conduct and complete multiple integral steps. We previously proposed the use of paper-based ELISA to rapidly detect the presence of E. coli. This approach has demonstrated utility for point-of-care (POC) urinary tract infection diagnoses. Paper-based ELISA, while advantageous, still requires the execution of several procedural steps. Here, we discuss the design and experimental implementation of a turntable paper-based device to simplify the paper-based ELISA protocols for the detection of E. coli. In this process, antibodies or reagents are preloaded onto zones of a paper-based device and allowed to dry before use. We successfully used this device to detect E. coli with a detection limit of 105 colony-forming units (colony-forming unit [CFU])/mL.

Bio-based monomers represent the future market for polymer chemistry, since the political economics of different states promote green ventures toward more sustainable materials and processes. Industrial pulp and paper processing represent a large market that could advance the use of by-products to avoid waste production and reduce pollution. Lignin represents the most available side product that can be used to produce a bio-based monomer. This review is concentrated on the possibility of using bio-based monomer derivates from pulp and the paper industry for UV-curing processing. UV-curing represents the new frontier for thermoset production, allowing a fast reaction cure, less energy demand, and the elimination of solvent. The growing demand for new monomers increases research in the environmental field to substitute for petroleum-based products. This review provides an overview of the main monomers and relative families of compounds derived from industrial processes that are suitable for UV-curing. Particular focus is given to the developments reached in the last few years concerning lignin, rosin and terpenes and the related possible applications of these in UV-curing chemistry.

In the last 10 years, paper-based electrochemical biosensors have gathered attention from the scientific community for their unique advantages and sustainability vision. The use of papers in the design the electrochemical biosensors confers to these analytical tools several interesting features such as the management of the solution flow without external equipment, the fabrication of reagent-free devices exploiting the porosity of the paper to store the reagents, and the unprecedented capability to detect the target analyte in gas phase without any sampling system. Furthermore, cost-effective fabrication using printing technologies, including wax and screen-printing, combined with the use of this eco-friendly substrate and the possibility of reducing waste management after measuring by the incineration of the sensor, designate these type of sensors as eco-designed analytical tools. Additionally, the foldability feature of the paper has been recently exploited to design and fabricate 3D multifarious biosensors, which are able to detect different target analytes by using enzymes, antibodies, DNA, molecularly imprinted polymers, and cells as biocomponents. Interestingly, the 3D structure has recently boosted the self-powered paper-based biosensors, opening new frontiers in origami devices. This review aims to give an overview of the current state origami paper-based biosensors, pointing out how the foldability of the paper allows for the development of sensitive, selective, and easy-to-use smart and sustainable analytical devices.

Introduction: Appropriate wheelchairs are often essential for the health and wellbeing of people with mobility impairments to enhance fundamental freedoms and equal opportunity. To date, provision has mainly focused on just delivering the wheelchair instead of following an evidence-based wheelchair service delivery process. In addition, many governments have not committed to a national wheelchair provision policy. Approach: To prepare this position paper, a systemic development model, founded on the sustainable human security paradigm, was employed to explore the global challenges to accessing appropriate wheelchairs. Positions: I: Consideration of key perspectives of wheelchair provision across the life course is essential to meet the needs to children, adults, older people and their families; II: Comprehensive wheelchair service delivery processes and a competent workforce are essential to ensure appropriate wheelchair service provision; III: Evaluations on wheelchair product quality development, performance and procurement standards are key as wheelchair product quality is generally poor; IV: Understanding the economic landscape when providing wheelchairs is critical. Wheelchair funding systems vary across jurisdictions; V: Establishing wheelchair provision policy is a key priority, as specific policy is limited globally. Conclusion: The vision is to take positive action to develop appropriate and sustainable wheelchair service provision systems globally, for me, for you, for us.

The main problem for the expansion of the use of microfluidic paper-based analytical devices and, thus, their mass production is their inherent lack of fluid flow control due to its uncontrolled fabrication protocols. To address this issue, the first step is the generation of uniform and reliable microfluidic channels. The most common paper microfluidic fabrication method is wax printing, which consists of two parts, printing and heating, where heating is a critical step for the fabrication of reproducible device dimensions. In order to bring paper-based devices to success, it is essential to optimize the fabrication process in order to always get a reproducible device. Therefore, the optimization of the heating process and the analysis of the parameters that could affect the final dimensions of the device, such as its shape, the width of the wax barrier and the internal area of the device, were performed. Moreover, we present a method to predict reproducible devices with controlled working areas in a simple manner. The authors would like to acknowledge funding support from Gobierno de España, Ministerio de Economía y Competitividad, with Grant No. BIO2016-80417-P (AEI/FEDER, UE), the Gobierno Vasco Dpto. Educación for the consolidation of the research groups (IT1271-19) and from Proyectos Colaborativos from the University of the Basque Country UPV/EHU, BIOPLASMOF (COLAB19/05). This project received funding from the European Union’s Horizon 2020 research and innovation programme under the Marie Skłodowska-Curie grant agreement No. 778001.

Paper-based biosensors are considered simple and cost-efficient sensing platforms for analytical tests and diagnostics. Here, a paper-based electrochemical biosensor was developed for the rapid and sensitive detection of microRNAs (miRNA-155 and miRNA-21) related to early diagnosis of lung cancer. Hydrophobic barriers to creating electrode areas were manufactured by wax printing, whereas a three-electrode system was fabricated by a simple stencil approach. A carbon-based working electrode was modified using either reduced graphene oxide or molybdenum disulfide nanosheets modified with gold nanoparticle (AuNPs/RGO, AuNPs/MoS2) hybrid structures. The resulting paper-based biosensors offered sensitive detection of miRNA-155 and miRNA-21 by differential pulse voltammetry (DPV) in only 5.0 mu L sample. The duration in our assay from the point of electrode modification to the final detection of miRNA was completed within only 35 min. The detection limits for miRNA-21 and miRNA-155 were found to be 12.0 and 25.7 nM for AuNPs/RGO and 51.6 and 59.6 nM for AuNPs/MoS2 sensors in the case of perfectly matched probe-target hybrids. These biosensors were found to be selective enough to distinguish the target miRNA in the presence of single-base mismatch miRNA or noncomplementary miRNA sequences., Newton-Katip Celebi funding program; Turkish Scientific and Technological Research Council (TUBITAK) [215Z702]; British Council (Newton Fund) [216182787]; Invest Northern Ireland under a Biodevices grant [RD0714186], This project was supported by the Newton-Katip Celebi funding program, and received a financial support from the Turkish Scientific and Technological Research Council (TUBITAK; Project no. 215Z702), the British Council (Newton Fund, Institutional Links, Ref: 216182787) and Invest Northern Ireland under a Biodevices grant, Ref. RD0714186.

We are glad to share with you our first Journal Club and to highlight some of the most interesting papers published recently. We hope we will tease your curiosity and encourage you to read full papers outside of your research area, which you may not have read otherwise. The Biomolecules Scientific Board wishes you an exciting read.

Paper mulberry (Broussonetia papyrifera, PM) is high protein but unutilized as a feed source. The study explores the different parts (leaf, stem, and whole plant) of PM chemical composition, silage fermentation, and in vitro and in situ digestibility, aiming to give some guidelines to PM usage as feed. The result showed that the leaf had a higher fresh weight than the stem (p &lt, 0.05). The dry matter contents of the three groups had no differences. The highest crude protein, ether extract, water-soluble carbohydrate, ash, calcium, phosphorus, amino acid contents, and butter capacity were observed in the leaf (p &lt, 0.05). The stem had the highest (p &lt, 0.05) neutral detergent fiber, acid detergent fiber, and lignin contents. After ensiling, the stem silage had the lowest pH value, ammonia nitrate (NH3-N), lactate, acetate, and propionate (p &lt, 0.05). The leaf silage had the highest pH value (p &lt, 0.05). The lactate, acetate, and propionate in the leaf and whole plant silage had no difference. The butyrate was not detected in all silage. The in vitro and in situ digestibility experiments showed the leaf had the highest digestibility (p &lt, 0.05), which could produce more volatile fatty acids and have a higher effective digestibility. These results allow a greater understanding of PM to be used as a feedstuff.

There is a growing demand for rapid and sensitive detection approaches for pathogenic bacteria that can be applied by non-specialists in non-laboratory field settings. Here, the detection of the typical E. coli enzyme &beta, glucuronidase using a chitosan-based sensing hydrogel-coated paper sensor and the detailed analysis of the reaction kinetics, as detected by a smartphone camera, is reported. The chromogenic reporter unit affords an intense blue color in a two-step reaction, which was analyzed using a modified Michaelis&ndash, Menten approach. This generalizable approach can be used to determine the limit of detection and comprises an invaluable tool to characterize the performance of lab-in-a-phone type approaches. For the particular system analyzed, the ratio of reaction rate and equilibrium constants of the enzyme&ndash, substrate complex are 0.3 and 0.9 pM&minus, 1h&minus, 1 for &beta, glucuronidase in phosphate buffered saline and lysogeny broth, respectively. The minimal degree of substrate conversion for detection of the indigo pigment formed during the reaction is 0.15, while the minimal time required for detection in this particular system is ~2 h at an enzyme concentration of 100 nM. Therefore, this approach is applicable for quantitative lab-in-a-phone based point of care detection systems that are based on enzymatic substrate conversion via bacterial enzymes.

The graphene paper microsieves can be applied in the filtration of biological fluids or separation of solid particles from exploitation fluids. To produce graphene paper microsieves for specific applications, good control over fabrication should be achieved. In this study, a laser ablation method using a picosecond laser was applied to fabricate graphene paper microsieves. Holes in the microsieves were drilled using pulsed laser radiation with a pulse energy from 5 to 100 &micro, J, a duration of 60 ps, a wavelength of 355 nm, and a repetition rate of 1 kHz. The impact method was applied using 10 to 100 pulses to drill one hole. To produce holes of a proper diameter which could separate biological particles of a certain size (&ge, 10 &micro, m), optimum parameters of graphene paper laser ablation were defined using the MATLAB software taking into account laser pulse energy, repetition rate, and a desired hole diameter. A series of structural tests were carried out to determine the quality of an edge and a hole shape. Experimental results and Laguerre&ndash, Gauss calculations in MATLAB were then compared to perform the analysis of the distribution of diffraction fringes. Optimum experimental parameters were determined for which good susceptibility of the graphene paper to laser processing was observed.

Screen-printed membrane sensors based on the use of paper and ceramic substrates are fabricated, characterized, and used for rapid batch and continuous monitoring of CrIII in the form of CrO42&minus, in some industrial products and wastewater samples. Strips of paper and ceramic platforms (15 &times, 5 mm) were covered with conductive carbon paint and then modified with polyaniline (PANI) film, to act as an ion-to-electron transducer, followed by a drop casting of plasticized poly (vinyl chloride) (PVC) Rhodamine-B chromate membrane as a recognition sensing material. In a 5.0 mmol L&minus, 1 Trizma buffer solution of pH ~8, the fabricated paper and ceramic based membrane sensors exhibited a near Nernstian response for CrVI ion with slopes of &minus, 29.7 &plusmn, 0.5 and &minus, 28.6 &plusmn, 0.3 mV decade&minus, 1, limit of detection 2.5 &times, 10&minus, 5 and 2.4 &times, 6 mol L&minus, 1 (1.3&ndash, 0.12 &micro, g mL&minus, 1), and linear concentration range 7.5 &times, 3&ndash, 5.0 &times, 5 and 7.5 &times, 1.0 &times, 5 mol L&minus, 1 (390-0.5 &micro, 1), respectively. Both sensors exhibited fast and stable potentiometric response, excellent reproducibility, and good selectivity with respect to a number of common foreign inorganic species. Impedance spectroscopy and chronopotentiometry data revealed a small resistance and a larger double layer capacitance due to the presence of the intermediate polyaniline (PAN) conductive layer. Furthermore, the formation of a water layer between the ion selective membrane (ISM) and the underlying conductor polymer and between the conducting polymer and the carbon conducting surface was greatly reduced. The developed disposable solid-contact potentiometric sensors offer the advantages of simple design, long term potential stability, flexibility, miniaturization ability, short conditioning time, and cost effectiveness that enable mass production. The sensors were successfully used for static and hydrodynamic measurements of total chromium in some leather tanning wastewater and nickel-chrome alloy samples. The results compare favorably with data obtained by atomic absorption spectrometry.

Non-enzymatic electrochemical glucose sensing was obtained by gold nanostructures on graphene paper, produced by laser or thermal dewetting of 1.6 and 8 nm-thick Au layers, respectively. Nanosecond laser annealing produces spherical nanoparticles (AuNPs) through the molten-phase dewetting of the gold layer and simultaneous exfoliation of the graphene paper. The resulting composite electrodes were characterized by X-ray photoelectron spectroscopy, cyclic voltammetry, scanning electron microscopy, micro Raman spectroscopy and Rutherford back-scattering spectrometry. Laser dewetted electrode presents graphene nanoplatelets covered by spherical AuNPs. The sizes of AuNPs are in the range of 10&ndash, 150 nm. A chemical shift in the XPS Au4f core-level of 0.25&ndash, 0.3 eV suggests the occurrence of AuNPs oxidation, which are characterized by high stability under the electrochemical test. Thermal dewetting leads to electrodes characterized by faceted not oxidized gold structures. Glucose was detected in alkali media at potential of 0.15&ndash, 0.17 V vs. saturated calomel electrode (SCE), in the concentration range of 2.5&minus, 30 mM, exploiting the peak corresponding to the oxidation of two electrons. Sensitivity of 1240 &micro, A mM&minus, 1 cm&minus, 2, detection limit of 2.5 &mu, M and quantifications limit of 20 &mu, M were obtained with 8 nm gold equivalent thickness. The analytical performances are very promising and comparable to the actual state of art concerning gold based electrodes.

Fallopia japonica is a plant, native to East Asia, Japan, China and Korea, but in North America and Europe it is classified as invasive species. The root system and strong growth of these plants can damage buildings, streets, paving, retaining walls etc. It forms thick colonies, which crowd out other herbaceous species. In our project it was found out that the stem biomass of Fallopia japonica contains 40 percent of cellulose, which is comparable to the raw materials from which paper fibers are typically produced. With chemical and mechanical procedures and treatments, the fibers from Fallopia japonica were prepared and successfully the packaging paper has been produced. Generally, paper is widely used in packaging applications and it is considered as environmentally friendly substrate. It consists of a porous cellulose structure, composed of long-chain molecules in a crystalline state with amorphous regions in-between. Due to hydrophilic nature of cellulose and fiber network porosity, water barrier properties are limited. Conventional coatings that are used to improve water resistance, involve synthetic polymers such as polyethylene, rubber latex, polyvinyl alcohol etc. Natural renewable polymers have been the focus of many researches in recent years. Paper coatings are also commonly used with wax, but the recyclability of laminated and waxed papers is limited due to the separation from the paper, which is connected to the environmental issues. In this study biodegradable coating such as polysaccharide chitosan, was applied to paper made from Fallopia japonica. Namely, non coated paper from Fallopia japonica has high hydrophilic character and therefore it is not suitable for all packaging products. The aim of the research was to investigate the influence of different concentrations of chitosan in coating solution (5 and 10% w/w) on the physical and mechanical properties of the mentioned paper substrate. The water and moisture resistance of the coated paper substrates were determined via Cobb60 value tests, water vapor permeability and moisture. Scanning electron microscopy (SEM) was used to evaluate the effect of coating on the microstructures and the porosity of the paper. The results showed the compatibility of chitosan and paper substrate. Tensile properties of the coated paper has given promising results already at lower concentration (5%) of chitosan. Tensile strength and elongation at break increased, mainly by connectedness of chitosan matrix and polymer chain interactions. With thermogravimetric analysis (TGA) thermal stability and weight changes were detected at coated paper. A high weight loss of 20%, between 300°C and 400°C was detected at 5% and 10% chitosan coated paper, due to the degradation of chitosan main chains. The coated papers possessed better thermal, mechanical and water resistant properties. Considering the biobased nature of the coating and used paper substrate, the procedure can offer environmentally friendly and sustainable solution toward new packaging material. Using a Fallopia japonica as a source for the paper fibers, the need for the wood fibers could decrease and at the same time, the negative impact on the environment could reduce.