Search

Electron transparent TEM lamella with unaltered microstructure and chemistry is the prerequisite for successful TEM explorations. Currently, TEM specimen preparation of quantum nanostructures, such as quantum dots (QDs), remains a challenge. In this work, we optimize the sample-preparation routine for achieving high-quality TEM specimens consisting of SrRuO3 (SRO) QDs grown on SrTiO3 (STO) substrates. We demonstrate that a combination of ion-beam-milling techniques can produce higher-quality specimens of quantum nanostructures compared to TEM specimens prepared by a combination of tripod polishing followed by Ar+ ion milling. In the proposed method, simultaneous imaging in a focused ion-beam device enables accurate positioning of the QD regions and assures the presence of dots in the thin lamella by cutting the sample inclined by 5{\deg} relative to the dots array. Furthermore, the preparation of TEM lamellae with several large electron-transparent regions that are separated by thicker walls effectively reduces the bending of the specimen and offers broad thin areas. The final use of a NanoMill efficiently removes the amorphous layer without introducing any additional damage., Comment: 20 pages, 6 figures, 1 table

Uniaxial fatigue testing of micro-mechanical metallic specimens can provide valuable insight into damage formation. Magnetic and piezomagnetic testing are commonly used for qualitative characterization of damage in ferromagnetic specimens. Sensitive and accurate measurements with magnetic sensors is a key part of such a characterization. This work presents an experimental setup to induce structural defects in a micro-mechanical fatigue test. Simultaneously, the resulting piezomagnetic signals are measured during the complete lifetime of the tested specimen. The key component is a highly sensitive optically pumped magnetometer (OPM) used to measure the piezomagnetic hysteresis of a small specimen whose structural defects can be analyzed on a small scale by other metallographic characterization methods as well. This setup aims to quantify the magnetic signatures of damage during the fatigue process, which could enable non-destructive mechanical testing of materials. This paper reports the initial results obtained from this novel micro-magneto-mechanical test setup for a ferritic steel specimen.

The electronics industry is creating complex miniaturized devices with steadily higher power density. The increase of maximum operating temperatures affects the thermo-mechanical load and imposes greater requirements on the quality of electronic packages. Fast and reliable methods for inspecting the quality of electronic components can help to improve production quality and to reduce waste and environmental burden. We present a compact optical sensor based on Electronic Speckle Pattern Interferometry (ESPI) that provides a possibility to carry out such control in a fast, precise and non-contact manner and can be integrated directly in a production line. Analysing thermo-mechanical deformations of objects under study, the system is capable of identifying common defects in electronic modules, such as die attachment delamination.

Artificial perovskite-oxide nanostructures possess intriguing magnetic properties due to their tailorable electron-electron interactions, which are extremely sensitive to the oxygen coordination environment. To date, perovskite-oxide nanodots with sizes below 50 nm have rarely been reported. Furthermore, the oxygen octahedral distortion and its relation to magnetic properties in perovskite oxide nanodots remain unexplored yet. Here, we have studied the magnetic anisotropy in patterned SrRuO3 (SRO) nanodots as small as 30 nm while performing atomic-resolution electron microscopy and spectroscopy to directly visualize the constituent elements, in particular oxygen ions. We observe that the magnetic anisotropy and RuO6 octahedra distortion in SRO nanodots are both nanodots' size-dependent but remain unchanged in the first 3-unit-cell interfacial SRO monolayers regardless of the dots' size. Combined with the first principle calculations, we unravel a unique structural mechanism behind the nanodots' size-dependent magnetic anisotropy in SRO nanodots, sugguesting that the competition between lattice anisotropy and oxygen octahedral rotation mediates anisotropic exchange interactions in SRO nanodots. These findings demonstrate a new avenue towards tuning magnetic properties of correlated perovskite oxides and imply that patterned nanodots could be a promising playground for engineering emergent functional behaviors., Comment: 21 pages and 4 figures for the main manuscript

Substrate surfaces terminated with a specific surface reconstruction are a prerequisite for the controlled epitaxial growth of most materials. Focusing on SrTiO3 (001) substrates, it has recently been shown that in situ substrate termination by thermal annealing has decisive advantages over standard termination methods. We report here that in situ substrate termination is a generally applicable method not restricted to SrTiO3 crystals. We specifically demonstrate the successful surface preparation of doped SrTiO3 (001), LaAlO3 (001), NdGaO3 (001), DyScO3 (110), TbScO3 (110), MgO (001), and Al2O3 (0001) surfaces.

We present the fabrication and exploration of arrays of nanodots of $SrRuO_3$ with dot sizes between 500 nm and 15 nm. Down to the smallest dot size explored, the samples were found to be magnetic with a maximum of the Curie temperature $T_C$ achieved by dots of 30 nm diameter. This peak in $T_C$ is associated with a dot-size-induced relief of the epitaxial strain, as evidenced by scanning transmission electron microscopy.

Single molecule magnets and single spin centres can be individually addressed when coupled to contacts forming an electrical junction. To control and engineer the magnetism of quantum devices, it is necessary to quantify how the structural and chemical environment of the junction affects the spin centre. Metrics such as coordination number or symmetry provide a simple method to quantify the local environment, but neglect the many-body interactions of an impurity spin coupled to contacts. Here, we utilize a highly corrugated hexagonal boron nitride monolayer to mediate the coupling between a cobalt spin in CoHx (x=1,2) complexes and the metal contact. While hydrogen controls the total effective spin, the corrugation smoothly tunes the Kondo exchange interaction between the spin and the underlying metal. Using scanning tunnelling microscopy and spectroscopy together with numerical simulations, we quantitatively demonstrate how the Kondo exchange interaction mimics chemical tailoring and changes the magnetic anisotropy., The spins of single molecules and defect centres possess properties which can be strongly influenced by their material contacts in electrical junctions. Here, the authors study the coupling between cobalt hydride complexes and a Rh(111) contact, mediated through a hexagonal boron nitride layer.