Search

A simple greenhouse ventilation model, based on the stack and wind effects (the main driving forces for natural ventilation) was adapted, calibrated and validated using measured air renewal rates in a three span naturally ventilated Azrom type greenhouse in Zimbabwe. Crop transpiration rates were monitored using stem heat balance sap flow gauges installed on the main stems of rose plants to continuously monitor whole-plant transpiration (WPT). This allowed continuous and automatic determination of full scale air renewal and leakage rates using the water vapour balance method. The model was fitted to experimental data of ventilation rates, and discharge and wind effect coefficients were determined. The results show a good fit between measured and predicted values (R2 = 0.80 and 0.82 for winter and summer, respectively), although there is a general over-estimation of the greenhouse air renewal rates, particularly during the night. The model, nevertheless, adequately describes the natural ventilation process in the greenhouse all year round. The model can be used as a design tool to evaluate and optimise the effects of different ventilation configurations and strategies on greenhouse air renewal rates, and as a component in a greenhouse climate model in order to further evaluate the effects of ventilation strategies on the inside greenhouse and crop microclimate, and thus lead to better greenhouse climate control.

In this study we determined the microclimatic drivers of storage water use in Scots pine (Pinus sylvestris L.) growing in a temperate climate. The storage water use was modeled using the ANAFORE model, integrating a dynamic water flow and – storage model with a process-based transpiration model. The model was calibrated and validated with sap flow measurements for the growing season of 2000 (26 May–18 October). Because there was no severe soil drought during the study period, we were able to study atmospheric effects. Incoming radiation was the main driver of storage water use. The general trends of sap flow and storage water use are similar, and follow more or less the pattern of incoming radiation. Nevertheless, considerable differences in the day-to-day pattern of sap flow and storage water use were observed, mainly driven by vapour pressure deficit (VPD). During dry atmospheric conditions (high VPD) storage water use was reduced. This reduction was disproportionally higher than the reduction in measured sap flow. Our results suggest that the trees did not rely more on storage water during periods of atmospheric drought, without severe soil drought. A third important factor was the tree water deficit. When storage compartments were depleted beyond a threshold, storage water use was limited due to the low water potential in the storage compartments. The maximum relative contribution of storage water to daily transpiration was also constrained by an increasing tree water deficit.

Quantitative analysis of wood anatomical characteristics is usually performed using classical microtomy yielding optical micrographs of stained thin sections. It is time-consuming to obtain high quality cross-sections from microtomy, and sections can be damaged. This approach, therefore, is often impractical for those who need quick acquisition of quantitative data on vessel characteristics in wood. This paper reports results of a novel approach using X-ray computed microtomography (microCT) for non-invasive determination of wood anatomy. As a case study, stem wood samples of a 2-year-old beech (Fagus sylvatica L.) and a 3-year-old oak (Quercus robur L.) tree were investigated with this technique, beech being a diffuse-porous and oak a ring-porous tree species. MicroCT allowed non-invasive mapping of 2-D transverse cross-sections of both wood samples with micrometer resolution. Self-developed software `μCTanalysis' was used for image processing of the 2-D cross-sections in order to automatically determine the inner vessel diameters, the transverse cross-sectional surface area of the vessels, the vessel density and the porosity with computer assistance. Performance of this new software was compared with manual analysis of the same micrographs. The automatically obtained results showed no significant statistical differences compared to the manual measurements. Visual inspection of the microCT slices revealed very good correspondence with the optical micrographs. Statistical analysis confirmed this observation in a more quantitative way, and it was, therefore, argued that anatomical analysis of optical micrographs can be readily substituted by automated use of microCT, and this without loss of accuracy. Furthermore, as an additional application of microCT, the 3-D renderings of the internal microstructure of the xylem vessels for both the beech and the oak sample could be reconstructed, clearly showing the complex nature of vessel networks. It can be concluded that the use of microCT in wood science offers an interesting potential for all those who need quantitative data of wood anatomical characteristics in either the 2-D or the 3-D space.