Search

A molecular dynamics (MD) simulation study was performed to investigate the effects of helium (He) on the mechanical properties of nanocrystalline body-centered cubic iron (BCC Fe). Simulated X-ray diffraction (XRD) was used to explore the relationship between the generation of cracks and the change of the crystal structure in nanocrystalline BCC Fe during tensile deformation. It is observed that the peak stress and the elastic modulus decrease with increasing concentration of He atoms, which are introduced into the grain boundary (GB) region of nanocrystalline Fe. The generation and connection of intergranular cracks are enhanced by He atoms. Significant peak separation, which is associated with the generation of cracks, is found in the simulated XRD patterns of nanocrystalline Fe during the tensile process. The lower diffraction angle of the {211}′ peak suggests a more serious lattice distortion during loading. For all nanocrystalline Fe deformed to 6% strain, the degree and fraction of the lattice distortion increases with the increasing loading stress.

Helium (He) effect on the microstructure of nanocrystalline body-centered cubic iron (BCC-Fe) was studied through Molecular Dynamics (MD) simulation and simulated X-ray Diffraction (XRD). The crack generation and the change of lattice constant were investigated under a uniaxial tensile strain at room temperature to explore the roles of He concentration and distribution played in the degradation of mechanical properties. The simulation results show that the expansion of the lattice constant decreases and the swelling rate increases while the He in the BCC region diffuses into the grain boundary (GB) region. The mechanical property of nanocrystalline BCC-Fe shows He concentration and distribution dependence, and the existence of He in GB is found to benefit the generation and growth of cracks and to affect the strength of GB during loading. It is observed that the reduction of tensile stress contributed by GB He is more obvious than that contributed by grain interior He.

The micro-structural effects of different neutron irradiation temperatures and helium contents, for 16 dpa dose, have been investigated by means of small-angle neutron scattering (SANS) in B-alloyed ferritic/martensitic steel Eurofer97-1 (0.12 C, 9 Cr, 0.2 V, 1.08 W wt%, B concentrations up to 1000 ppm); due to B transmutations, fusion relevant He/dpa values are expected to be produced under neutron irradiation. SANS measurements have been carried out on a sample irradiated at 350 °C, with estimated helium content of 5600 appm, and compared to previous SANS results, obtained on two other irradiated samples of this same B-alloyed steel. These new measurements confirm that for such high helium contents the SANS cross-section increases in order of magnitude and the magnetic SANS component is strongly reduced, compared to lower helium content (400 appm). Such effects are attributed to increase in helium bubbles density and to the presence of micro-cavities, produced after dissolution of large B-carbides. The SANS data analysis procedure has been improved, also thanks to the additional information provided by the new measurements, and more accurate helium bubble size distributions have been obtained for all the investigated samples. For 5600 appm helium content, bubble volume fractions are found of 0.025 for the sample irradiated at 350 °C and of 0.041 for the previously investigated sample irradiated at 400 °C, significantly increasing with the irradiation temperature. These values are approximately one order of magnitude larger than the value of 0.003 previously found for the sample with 400 appm helium. The size distributions are compared with electron microscopy observations of these same samples. It appears that the occurrence of complex micro-structural changes in irradiated Eurofer97-1 steel should be taken in due account when considering its application under high He/dpa ratio values. Keywords: Helium effects, Neutron irradiation, Small angle neutron scattering, Electron microscopy

The purification and its influence on the property are important in developing low activation ferritic steels for fusion applications. In order to clarify the influence of purity on microstructure development in Fe-Cr alloys, the cavity formation caused by relatively high amount of helium was studied. High-purity Fe-9Cr binary alloys (99.99-99.995 wt% purity) and commercial-grade ones (99.9-99.95 wt% purity) were prepared. About 1000 appm helium associated with about 0.2 dpa was implanted into TEM disks at room temperature by using a Dynamitron accelerator with energy degrader. After post-irradiation annealing at 1123 K for 3.6 ks small cavities were observed in the high-purity alloys half in average size and 3-10 times higher in density compared with commercial-grade ones. The role of trace elements in cavity formation was discussed.

Phosphorus and/or titanium modified Fe-16Cr-17Ni austenitic alloys doped with ^B were irradiated in FFTF/MOTA at 684 K for the purpose of investigating the influence of helium generation on the swelling suppression effects by phosphorus and titanium. The increase in void density caused by ^B addition resulted in swelling increase in phosphorus-modified alloys. The close relation between the dislocation density and the void swelling implied the enhancement of dislocation density as a possible mechanism of the swelling suppression by phosphorus addition at the present temperature.