Search

The present study aimed to evaluate the effect of dipyridamole, an indirect adenosine 2A receptors (A2AR), on the osseointegration of titanium implants in a large, translational pre-clinical model. Sixty tapered, acid-etched titanium implants, treated with four different coatings ((i) Type I Bovine Collagen (control), (ii) 10 μM dipyridamole (DIPY), (iii) 100 μM DIPY, and (iv) 1000 μM DIPY), were inserted in the vertebral bodies of 15 female sheep (weight ~65 kg). Qualitative and quantitative analysis were performed after 3, 6, and 12 weeks in vivo to assess histological features, and percentages of bone-to-implant contact (%BIC) and bone area fraction occupancy (%BAFO). Data was analyzed using a general linear mixed model analysis with time in vivo and coating as fixed factors. Histomorphometric analysis after 3 weeks in vivo revealed higher BIC for DIPY coated implant groups (10 μM (30.42% ± 10.62), 100 μM (36.41% ± 10.62), and 1000 μM (32.46% ± 10.62)) in comparison to the control group (17.99% ± 5.82). Further, significantly higher BAFO was observed for implants augmented with 1000 μM of DIPY (43.84% ± 9.97) compared to the control group (31.89% ± 5.46). At 6 and 12 weeks, no significant differences were observed among groups. Histological analysis evidenced similar osseointegration features and an intramembranous-type healing pattern for all groups. Qualitative observation corroborated the increased presence of woven bone formation in intimate contact with the surface of the implant and within the threads at 3 weeks with increased concentrations of DIPY. Coating the implant surface with dipyridamole yielded a favorable effect with regard to BIC and BAFO at 3 weeks in vivo. These findings suggest a positive effect of DIPY on the early stages of osseointegration.

Over the past couple of decades, additive manufacturing and the use of root-analogue-printed titanium dental implants have been developed. Not all powder particles are sintered into the final product during the additive manufacturing process. Reuse of the remaining powder could reduce the overall implant manufacturing cost. However, Ti-6Al-4V powder particles are affected by heat, mechanical factors, and oxidization during the powder bed fusion manufacturing process. Degradation of the powder may harm the final surface composition and decrease the biocompatibility and survival of the implant. The uncertainty of the recycled powder properties prevents implant fabrication facilities from reusing the powder. This study investigates the chemical composition of controlled, clean, and recycled titanium alloy powder and root-analogue implants (RAI) manufactured from these powders at three different depths. The change in titanium’s quantity, oxidization state, and chemical composition in powder and RAI implants have been demonstrated and analyzed. While not identical, the surface chemical composition of the recycled powder implant and the implant manufactured from unused powder are similar. The results also indicate the presence of TiO2 on all surfaces. Many studies confirmed that titanium dioxide on the implant’s surface correlates with better osteointegration, reduced bacterial infection, and increased corrosion resistance. Considering economic and environmental aspects, surface chemical composition comparison of clean and reused powder is crucial for the future manufacturing of cost-effective and biocompatible implants.

Reduced skeletal loading associated with many conditions, such as neuromuscular injuries, can lead to bone fragility and may threaten the success of implant therapy. Our group has developed a botulinum toxin A (botox) injection model to imitate disease-reduced skeletal loading and reported that botox dramatically impaired the bone formation and osseointegration of titanium implants. Semaphorin 3A (sema3A) is an osteoprotective factor that increases bone formation and inhibits bone resorption, indicating its potential therapeutic role in improving osseointegration in vivo. We first evaluated the sema3A effect on whole bone morphology following botox injections by delivering sema3A via injection. We then evaluated the sema3A effect on the osseointegration of titanium implants with two different surface topographies by delivering sema3A to cortical bone defect sites prepared for implant insertion and above the implants after insertion using a copper-free click hydrogel that polymerizes rapidly in situ. Implants had hydrophobic smooth surfaces (PT) or multiscale biomimetic micro/nano topography (SLAnano). Sema3A rescued the botox-impaired bone formation. Furthermore, biomimetic Ti implants improved the bone-to-implant contact (BIC) and mechanical properties of the integrated bone in the botox-treated rats, which sema3A enhanced. This study demonstrated the value of biomimetic approaches combining multiscale topography and biologics in improving the clinical outcomes of implant therapy.

(1) Background: Electrical stimulation is a promising alternative to promote bone fracture healing but with the limitation of tracking the osteogenesis progress in vivo. To overcome this issue, we present an opportunity to combine the electrical stimulation of a commercial titanium implant, which promotes osteogenesis within the fracture, with a real-time readout of the osteogenic progress by impedance sensing. This makes it possible to adjust the electrical stimulation modalities to the individual patient’s fracture healing process. (2) Methods: In detail, osteogenic differentiation of several cell types was monitored under continuous or pulsatile electrical stimulation at 0.7 V AC/20 Hz for at least seven days on a titanium implant by electric cell-substrate impedance sensing (ECIS). For control, chemical induction of osteogenic differentiation was induced. (3) Results: The most significant challenge was to discriminate impedance changes caused by proliferation events from those initiated by osteogenic differentiation. This discrimination was achieved by remodeling the impedance parameter Alpha (α), which increases over time for pulsatile electrically stimulated stem cells. Boosted α-values were accompanied by an increased formation of actin stress fibers and a reduced expression of the focal adhesion kinase in the cell periphery; morphological alterations known to occur during osteogenesis. (4) Conclusions: This work provided the basis for developing an effective fracture therapy device, which can induce osteogenesis on the one hand, and would allow us to monitor the induction process on the other hand.

Background context. Dental implants are designed to replace a missing tooth. Implant stability is vital to achieving osseointegration and successful implantation. Although there are many implants available on the market, there is room for improvement. Purpose. We describe a new dental implant with improved primary stability features. Study design. Lab bench test studies. Methods. We evaluated the new implant using static and flexion–compression fatigue tests with compression loads, 35 Ncm tightening torque, displacement control, 0.01 mm/s actuator movement speed, and 9–10 Hz load application frequency, obtaining a cyclic load diagram. We applied variable cyclic loadings of predetermined amplitude and recorded the number of cycles until failure. The test ended with implant failure (breakage or permanent deformation) or reaching five million cycles for each load. Results. Mean stiffness was 1151.13 ± 133.62 SD N/mm, mean elastic limit force 463.94 ± 75.03 SD N, and displacement 0.52 ± 0.04 SD mm, at failure force 663.21 ± 54.23 SD N and displacement 1.56 ± 0.18 SD mm, fatigue load limit 132.6 ± 10.4 N, and maximum bending moment 729.3 ± 69.43 mm/N. Conclusions. The implant fatigue limit is satisfactory for incisor and canine teeth and between the values for premolars and molars for healthy patients. The system exceeds five million cycles when subjected to a 132.60 N load, ensuring long-lasting life against loads below the fatigue limit.

Titanium is considered to be the most essential metal in the field of implantology. The main factors determining metal biocompatibility, among others, include the morphology and chemical composition of the titanium surface. Therefore, the aim of this work was to develop approaches to control the biological activity of the titanium surface by creating coatings that combine both an inorganic phase with a given morphology and organic molecules containing an integrin-selective peptide that regulate cell adhesion and proliferation. As such, we synthesized new c(RGDfC) derivatives of amino acid bisphosphonates (four examples) with different bisphosphonate anchors and maleimide linkers. These molecules were deposited on a highly developed porous surface obtained via the plasma electrolytic oxidation (PEO) of coarse-grained and nanostructured titanium. In vitro studies demonstrated the increase in the viability degree of mesenchymal stem cells and fibroblasts on the surface of coarse-grained or nanostructured titanium modified with PEO and a c(RGDfC) derivative of ε-aminocaproic acid bisphophonate with an SMCC linker. As a result, the use of conjugates of amino acid bisphosphonates with a cyclic RGD peptide for the modification of PEO-coated titanium opens the ways for the effective control of the biological activity of the metal implant surface.

Background: Nowadays, a combination of classical subperiosteal implant designs with 3D imaging and printing allows one to reduce treatment time and provides support for fixed prostheses in cases where other techniques do not provide satisfactory results. This study aims to present a digital technique for the manufacturing of custom-made subperiosteal implants and what complications might appear after this type of surgery. Methods: Sixteen patients treated with a custom-made DMLS titanium subperiosteal implant during the period between October 2021 and February 2022 were enrolled in the study. Orthopantomography (OPT) and cone-beam computer tomography (CBCT) were recorded for all patients. The measurements taken into account in this study were the fit and stability of implants, duration of surgery, implant survival, and early and late complications. Results: The fit of the implants was extremely satisfactory, with a mean rating of 4 out of 5. The mean duration of the intervention was 86.18 min. At the end of the study, one implant was lost due to insufficient fit and recurrent, untreatable infections. Eleven implants (69%) were placed on the maxillary and five (31%) implants were placed on the mandible. Conclusions: Taking this into consideration, custom-made DMLS titanium subperiosteal implants could present satisfactory implant survival and low complication rates.

Refereed/Peer-reviewed The demand for medical implants globally has increased significantly due to an aging population amongst other reasons. Despite the overall increase in the survivorship of Ti6Al4V implants, implant infection rates are increasing due to factors such as diabetes, obesity, and bacterial resistance to antibiotics. Two commonly found bacteria implicated in implant infections are Staphylococcus aureus and Pseudomonas aeruginosa. Based on prior work that showed nanostructured surfaces might have potential in passively killing these bacterial species, we developed a hierarchical, hydrothermally etched, nanostructured titanium surface. To evaluate the antibacterial efficacy of this surface, etched and as-received surfaces were inoculated with S. aureus or P. aeruginosa at concentrations ranging from 10(2) to 10(9) colony-forming units per disc. Live/dead staining revealed there was a 60% decrease in viability for S. aureus and greater than a 98% decrease for P. aeruginosa on etched surfaces at the lowest inoculum of 10(2) CFU/disc, when compared to the control surface. Bactericidal efficiency decreased with increasing bacterial concentrations in a stepwise manner, with decreases in bacterial viability noted for S. aureus above 10(5) CFU/disc and above 10(6) CFU/disc for P. aeruginosa. Surprisingly, biofilm depth analysis revealed a decrease in bacterial viability in the 2 mu m layer furthest from the nanostructured surface. The nanostructured Ti6Al4V surface developed here holds the potential to reduce the rate of implant infections.

Aim: The aim of this study was to investigate the combined effect of the lateral-compression of host-bone (undersized-osteotomy-preparation) and axial-compression of host-bone (not drilling the full length of the implant) on the primary-implant-stability and the host-bone-architecture. Materials and Methods: In this experimental-study, 44 dental implants (diameter-4.2 mm; length-10 mm; Dyna®) were installed in the femoral-condyles of four cadaver-goats using four different surgical approaches (11 implant/surgical approach; n = 11). Approach-1: Standard preparation according to the manufacturer's guidelines. The bone-cavity was prepared up to 10 mm in depth and 4 mm in diameter. Approach-2: Preparation up to 8 mm in depth and 4 mm in diameter. Approach-3: Preparation up to 10 mm in depth. Approach-4: The bone-cavity was prepared up to 8 mm in depth and 3.6 mm in diameter. Insertion torque (n = 11), removal torque (n = 7) and % bone-implant contact (n = 4) measurements were recorded. Bone architecture was assessed by micro-computer tomography and histological analysis (n = 4). Results: For approaches 2, 3, and 4 (P

Dental materials are expected to be biocompatible, non-cytotoxic, with the ability to maintain a mutual interaction with the host and performs the proper functions. In 2004 Graphene, where carbon atoms of sp2 hybridisation are organised in a single layer, was invented by “Prof. Andre Geim and Prof. Konstantin Novoselov” in 2004. It possesses excellent physical and mechanical properties. The properties like excellent biocompatibility and antimicrobial nature and ability to function alone or combining with other biomaterials, offer various opportunities to be used in multiple clinical applications. The motto of this review article to put some light on the overall status in the development of graphene and its application, function, and future perspective.

ispartof: SURFACE ENGINEERING vol:38 issue:4 pages:430-439 status: published

Titanium implant success is compromised by microbial biofilms and aseptic loosening. This research aimed to develop robust multifunctional class II organic-inorganic hybrid coatings for implants with osteoconductive and antibacterial properties. 3-Glycidoxypropyltrimethoxysilane was coupled with organic polymer poly(ethylene) glycol-diamine (PEG-NH2) for integration into an inorganic sol backbone composed of tetraethoxysilane and calcium, which was sourced from newly synthesized calcium-2-ethoxyethoxide. Nuclear magnetic resonance and attenuated total reflectance Fourier transform infrared spectroscopy confirmed synthesis of precursors and the structure of coating constituents. Scanning electron microscopy and energy-dispersive X-ray spectroscopy (EDS) demonstrated homogenous coatings, micro-topographical surface features, and apatite-like ex vivo mineralization in simulated body fluid. Tensile adhesion testing demonstrated robust and highly adherent (15.1 ± 3.3 MPa) coatings on titanium substrates. Hybrid coatings imbedded with silver nanoparticles (nAg) significantly inhibited (P < 0.05) Staphylococcus aureus and Escherichia coli planktonic cultures and biofilm formation. These Si-Ca-PEG-nAg hybrid coatings for titanium implants offer robust multifunctional features.

Objective The present work was aimed to evaluate the effect of valproic acid (VPA)，Parathyroid hormone (1–34) (PTH)+VPA on Ti rods osseointegration in ovariectomized rats and further investigation of the possible mechanism. Methods The MC3T3-E1 cells were co-cultured with VPA，PTH ​+ ​VPA and induced to osteogenesis, and the cell viability，mineralization ability were observed by MTT and ALP staining，Alizarin Red staining and Western blotting. Twelve weeks after bilateral ovariectomy, all animals were randomly divided into four groups: group OVX and VPA，PTH ​+ ​VPA, and all the rats received Ti implants and animals belong to group VPA，PTH ​+ ​VPA received valproic acid (300 ​mg/day), valproic acid (300 ​mg/day) plus Parathyroid hormone (1–34) every 3 days (60 ​μg/kg), respectively, treatment until death at 12 weeks. Micro-CT, histology, biomechanical testing, bone metabolism index and Reverse transcription-quantitative polymerase chain reaction (RT-qPCR) analysis were used to observe the therapeutic effect and explore the possible mechanism. Results Results shown that VPA decreased new bone formation around the surface of titanium rods and push-out force other than group OVX. Histology, Micro-CT and biochemical analysis results showed combined application of systemic VPA showed harmful effects than OVX group on bone formation in osteopenia rats, with the worse effects on CTX-1, P1NP and microarchitecture as well as biomechanical parameters by down-regulated gene expression of Runx2, OCN, Smad1, BMP-2 and OPG, while up-regulated RANKL. However, after PTH treatment, the above indicators were significantly improved. Conclusions The present study suggests that systemic use of VPA may bring harm to the stability of titanium implants in osteoporosis, PTH can reverse the negative effect of VPA on the osseointegration of titanium rods in ovariectomized rats. Translational potential of this article According to our research, when patients with epilepsy have osteoporotic fractures, after joint replacement or internal fixation, continue to use sodium valproate for anti-epileptic therapy, the possibility of postoperative loosening increases, again on the basis of It can be reversed with the anti-osteoporosis drug parathyroid hormone (1-34).

Previously, functional coatings on 3D-printed titanium implants were developed to improve their biointegration by separately incorporating Ga and Ag on the biomaterial surface. Now, a thermochemical treatment modification is proposed to study the effect of their simultaneous incorporation. Different concentrations of AgNO3 and Ga(NO3)3 are evaluated, and the obtained surfaces are completely characterized. Ion release, cytotoxicity, and bioactivity studies complement the characterization. The provided antibacterial effect of the surfaces is analyzed, and cell response is assessed by the study of SaOS-2 cell adhesion, proliferation, and differentiation. The Ti surface doping is confirmed by the formation of Ga-containing Ca titanates and nanoparticles of metallic Ag within the titanate coating. The surfaces generated with all combinations of AgNO3 and Ga(NO3)3 concentrations show bioactivity. The bacterial assay confirms a strong bactericidal impact achieved by the effect of both Ga and Ag present on the surface, especially for Pseudomonas aeruginosa, one of the main pathogens involved in orthopedic implant failures. SaOS-2 cells adhere and proliferate on the Ga/Ag-doped Ti surfaces, and the presence of gallium favors cell differentiation. The dual effect of both metallic agents doping the titanium surface provides bioactivity while protecting the biomaterial from the most frequent pathogens in implantology.

Background Implant-associated infections (IAI) remain a challenging complication in osteosynthesis. There is no consensus or clear evidence whether titanium offers a relevant clinical benefit over stainless steel. Purpose In this systematic review, we sought to determine whether the implant properties of titanium reduce the susceptibility to IAI compared to stainless steel in fracture management. Methods A systematic literature search in German and English was performed using specific search terms and limits. Studies published between 1995 and 1st June 2020 in the Cochrane library, MEDLINE and Web of Science databases were included. Only clinical studies comparing titanium and stainless steel implants regarding the susceptibility to infections were selected for detailed review. Results Five studies out of 384 papers were identified and reviewed. From the studies meeting inclusion criteria one study was a systematic review, two studies were randomized controlled studies (RCT) and two studies were of retrospective comparative nature of level IV evidence. Conclusion Our results show that currently, no proven advantage for titanium implants in respect to IAI can be seen in contemporary literature. Implants preserving periosteal blood-flow and minimising soft-tissue trauma show statistically significant benefits in reducing the incidence of IAI. Clinical studies providing reliable evidence regarding the influence of titanium implants on IAI and investigating the susceptibility of titanium to infection are necessary

In the design of multifunctional orthopedic biomaterials, enhanced biological activities, reinforced mechanical property, improved hydrophilicity and osteo-compatibility are the essential criteria. For achieving these goals, here a bioactive multifunctional Ti6Al4V implant with nanowire structured surface topography is designed and fabricated using 3D printing technique. Selective laser melting (SLM) is applied to fabricate scaffold materials with diamond cellular structures to meet the requirements of load-bearing function of bone tissue. With the alkali treatment of sodium hydroxide, osteogenic layer of Na2Ti6O13 is generated on the porous Ti6Al4V, on which apatite is easily deposited and immobilized. Clusters of Na2Ti6O13 exhibits excellent hydrophilicity and surface roughness with precise control of alkali treatment time. Additionally, the compressive strength of the modified porous Ti6Al4V (121.2 MPa-84.5 MPa) decreases due to the corrosion of sodium hydroxide, while it can satisfy the basic mechanical requirement of cortical bone. The results prove that the surface-modified 3D printed porous Ti6Al4V possesses balanced mechanical strength and osteogenic function, promising for potential application in complex multifunctional bone defects.

Treatment of implant-associated infection is becoming more challenging, especially when bacterial biofilms form on the surface of the implants. Developing multi-mechanism antibacterial methods to combat bacterial biofilm infections by the synergistic effects are superior to those based on single modality due to avoiding the adverse effects arising from the latter. In this work, TiO2 nanorod arrays in combination with irradiation with 808 near-infrared (NIR) light are proven to eradicate single specie biofilms by combining photothermal therapy, photodynamic therapy, and physical killing of bacteria. The TiO2 nanorod arrays possess efficient photothermal conversion ability and produce a small amount of reactive oxygen species (ROS). Physiologically, the combined actions of hyperthermia, ROS, and puncturing by nanorods give rise to excellent antibacterial properties on titanium requiring irradiation for only 15 min as demonstrated by our experiments conducted in vitro and in vivo. More importantly, bone biofilm infection is successfully treated efficiently by the synergistic antibacterial effects and at the same time, the TiO2 nanorod arrays improve the new bone formation around implants. In this protocol, besides the biocompatible TiO2 nanorod arrays, an extra photosensitizer is not needed and no other ions would be released. Our findings reveal a rapid bacteria-killing method based on the multiple synergetic antibacterial modalities with high biosafety that can be implemented in vivo and obviate the need for a second operation. The concept and antibacterial system described here have large clinical potential in orthopedic and dental applications., Graphical abstract In this work, TiO2 nanorod arrays in combination with irradiation with 808 near-infrared (NIR) light are proven to eradicate biofilms by combining photothermal therapy, photodynamic therapy, and physical killing of bacteria.Image 1, Highlights • Various TiO2 nanostructures were prepared on titanium. • The TiO2 nanorod arrays exhibited excellent antibacterial properties under the irradiation of 808 nm NIR light. • The combined actions of hyperthermia, ROS, and puncturing produced superior antibacterial activity in vitro and in vivo. • In this antibacterial system, besides the biocompatible TiO2 nanorod arrays, an extra photosensitizer is not needed.

Made available in DSpace on 2022-05-01T13:41:30Z (GMT). No. of bitstreams: 0 Previous issue date: 2022-01-01 Objective: The objective of this study was to evaluate in vitro the influence of the anodized surface of Ti35Nb7Zr alloy on the behavior of osteogenic cells, for future application in biomedical implants. Material and Methods: For the development of this research, samples of commercially pure titanium (TiCp) and samples of Ti35Nb7Zr alloy were anodized, both were characterized by scanning electron microscopy (SEM) and were plated afterwards with human osteoblast-like cells (MG63 line) (2 x 104). Cell adhesion, cytotoxicity test, formation of mineralization nodules and a comet assay were also performed in different periods. The bottom of the plate was used as a control, without a sample. Results: SEM analysis showed that the topography of both samples presented surfaces covered by nanotubes. Cellular morphology exhibited spreading in both samples proposing an intimate cell-material liaison. After 3 days, the Ti35Nb7Zr group exhibited greater cell viability than the TiCp group (p0.05) among the groups in the evaluated periods. Conclusion: It was concluded that this process of anodization was efficient to form nanotubes, as well as promote a positive influence on the behavior of osteogenic cells without promoting cell damage. Universidade Estadual Paulista “Júlio de Mesquita Filho” Institute of Science and Technology Department of Bioscience and Oral Diagnosis, SP Universidade de São Paulo Escola de Engenharia de Lorena Department of Engineering Materials, SP Universidade do Vale do Paraíba Institute of Research and Development, SP Universidade de São Paulo Escola de Engenharia de Lorena, SP Universidade Estadual Paulista “Júlio de Mesquita Filho” Institute of Science and Technology Department of Bioscience and Oral Diagnosis, SP

Objective: Titanium (Ti) is considered bioinert and is still regarded as the “gold standard” material for dental implants. However, even ‘commercial pure’ Ti will contain minor fractions of elemental impurities. Evidence demonstrating the release of Ti ions and particles from ‘passive’ implant surfaces is increasing and has been attributed to biocorrosion processes which may provoke immunological reactions. However, Ti observed in peri-implant tissues has been shown to be co-located with elements considered impurities in biomedical alloys. Accordingly, this study aimed to quantify the composition of impurities in commercial Ti dental implants. Methods: Fifteen commercial titanium dental implant systems were analyzed using inductively coupled plasma-mass spectrometry (ICP-MS) and optical emission spectrometry (ICP-OES). Results: The elemental composition of implants manufactured from commercially pure grades of Ti, Ti-6Al-4V, and the TiZr alloy (Roxolid) conformed to the respective ISO/ASTM standards or manufacturers´ data (TiZr/Roxolid). However, all implants investigated included exogenous metal contaminants including Ni, Cr, Sb, and Nb to a variable extent. Other contaminants detected in a fraction of implants included As and the radionuclides U-238 and Th-232. Significance: Although all Ti implant studies conformed with their standard compositions, potentially allergenic, noxious metals and even radionuclides were detected. Since there are differences in the degree of contamination between the implant systems, a certain impurity fraction seems technically avoidable. The clinical relevance of these findings must be further investigated, and an adaptation of industry standards should be discussed.

Titan se běžně a úspěšně používá v zubních a ortopedických implantátech. Nicméně, pacienti stále musí čelit riziku selhání implantátu z různých důvodů, jako např. uvolnění implantátu nebo infekce. Riziku uvolnění implantátu lze čelit pomocí optimalizace osteointegrační kapacity implantovaných materiálů. Úpravy povrchu implantátu jako jsou strukturování, zdrsnění a biologická aktivace ve prospěch osteogenních diferenciace byly rozsáhle studovány. Klíčový faktor pro úspěšnou stabilní dlouhodobou perspektivu integrace je počáteční buněčná reakce na materiál implantátu. Proto interakce buňka-implantát, která je závislá na parametrech povrchu v návrhu implantátu, musí být zohledňována při návrhu implantátu. Tato „review“ práce začíná základními informacemi o interakcí buněk s materiály a o běžných technikách povrchových úprav. Poté je zkoumán a diskutován aktuální stav výzkumu v oblasti dopadu osteogenních procesů a dále jsou zkoumány a diskutovány in vitro a in vivo rekace, které jsou vyvolany různými povrchovými úpravami, s cílem poskytnout informace o aktuálně používaných a vyvíjejících se úpravách implantátů techniky pro zlepšení osteointegrace. Titanium is commonly and successfully used in dental and orthopedic implants. However, patients still have to face the risk of implant failure due to various reasons, such as implant loosening or infection. The risk of implant loosening can be countered by optimizing the osteointegration capacity of implant materials. Implant surface modifications for structuring, roughening and biological activation in favor for osteogenic differentiation have been vastly studied. A key factor for a successful stable longterm integration is the initial cellular response to the implant material. Hence, cell–material interactions, which are dependent on the surface parameters, need to be considered in the implant design. Therefore, this review starts with an introduction to the basics of cell–material interactions as well as common surface modification techniques. Afterwards, recent research on the impact of osteogenic processes in vitro and vivo provoked by various surface modifications is reviewed and discussed, in order to give an update on currently applied and developing implant modification techniques for enhancing osteointegration.

Objectives. The purpose of this work was to determine the influence of residual alumina after sand blasting treatment in titanium dental implants. This paper studied the effect of alumina on physico-chemical surface properties, such as: surface wettability, surface energy. Osseointegration and bacteria adhesion were determined in order to determine the effect of the abrasive particles. Materials and Methods. Three surfaces were studied: (1) as-received, (2) rough surface with residual alumina from sand blasting on the surface and (3) with the same roughness but without residual alumina. Roughness was determined by white light interferometer microscopy. Surface wettability was evaluated with a contact angle video-based system and the surface free energy by means of Owens and Wendt equation. Scanning electron microscopy equipped with microanalysis was used to study the morphology and determine the chemical composition of the surfaces. Bacteria (Lactobacillus salivarius and Streptococcus sanguinis) were cultured in each surface. In total, 110 dental implants were placed into the bone of eight minipigs in order to compare the osseointegration. The percentage of bone-to-implant contact was determined after 4 and 6 weeks of implantation with histometric analysis. Results. The surfaces with residual alumina presented a lower surface free energy than clean surfaces. The in vivo studies demonstrated that the residual alumina accelerated bone tissue growth at different implantation times, in relation to clean dental implants. In addition, residual alumina showed a bactericidal effect by decreasing the quantity of bacteria adhering to the titanium. Conclusions. It is possible to verify the benefits that the alumina (percentages around 8% in weight) produces on the surface of titanium dental implants. Clinical relevance. Clinicians should be aware of the benefits of sand-blasted alumina due to the physico-chemical surface changes demonstrated in in vivo tests.

Titanium implants have always been regarded as one of the gold standard treatments for orthopedic applications, but they still face challenges such as pain, bacterial infections, insufficient osseointegration, immune rejection, and difficulty in personalizing treatment in the clinic. These challenges may lead to the patients having to undergo a painful second operation, along with increased economic burden, but the use of drugs is actively solving these problems. The use of systemic drug delivery systems through oral, intravenous, and intramuscular injection of various drugs with different pharmacological properties has effectively reduced the levels of inflammation, lowered the risk of endophytic bacterial infection, and regulated the progress of bone tumor cells, processing and regulating the balance of bone metabolism around the titanium implants. However, due to the limitations of systemic drug delivery systems—such as pharmacokinetics, and the characteristics of bone tissue in the event of different forms of trauma or disease—sometimes the expected effect cannot be achieved. Meanwhile, titanium implants loaded with drugs for local administration have gradually attracted the attention of many researchers. This article reviews the latest developments in local drug delivery systems in recent years, detailing how various types of drugs cooperate with titanium implants to enhance antibacterial, antitumor, and osseointegration effects. Additionally, we summarize the improved technology of titanium implants for drug loading and the control of drug release, along with molecular mechanisms of bone regeneration and vascularization. Finally, we lay out some future prospects in this field.

Titanium and its alloys are dominant material for orthopedic/dental implants due to their stable chemical properties and good biocompatibility. However, aseptic loosening and peri-implant infection remain problems that may lead to implant removal eventually. The ideal orthopedic implant should possess both osteogenic and antibacterial properties and do proper assistance to in situ inflammatory cells for anti-microbe and tissue repair. Recent advances in surface modification have provided various strategies to procure the harmonious relationship between implant and its microenvironment. In this review, we provide an overview of the latest strategies to endow titanium implants with bio-function and anti-infection properties. We state the methods they use to preparing these efficient surfaces and offer further insight into the interaction between these devices and the local biological environment. Finally, we discuss the unmet needs and current challenges in the development of ideal materials for bone implantation.

Titanium (Ti) implants are widely used in dentistry and orthopedics owing to their excellent corrosion resistance, biocompatibility, and mechanical properties, which have gained increasing attention from the viewpoints of fundamental research and practical applications. Also, numerous studies have been carried out to fine-tune the micro/nanostructures of Ti and/or incorporate chemical elements to improve overall implant performance. Zinc oxide nanoparticles (nano-ZnO) are well-known for their good antibacterial properties and low cytotoxicity along with their ability to synergize with a variety of substances, which have received increasingly widespread attention as biomodification materials for implants. In this review, we summarize recent research progress on nano-ZnO modified Ti-implants. Their preparation methods of nano-ZnO modified Ti-implants are introduced, followed by a further presentation of the antibacterial, osteogenic, and anti-corrosion properties of these implants. Finally, challenges and future opportunities for nano-ZnO modified Ti-implants are proposed. Graphical Abstract

Objectives: Numerous arthroplasties require revision due to implant loosening, a failure of osteointegration on account of fibrous tissue or infection. The micro-to-nano-features of implant surfaces greatly influence cell behaviour at the tissue-implant-interface and thereby the subsequent osteointegration. [for full text, please go to the a.m. URL]

This study aimed to evaluate the effects of two types of provisional resin cements on the color and retentive strength of two different all-ceramic restorations cemented onto customized zirconia abutments. Forty-two crowns were made of monolithic zirconia and lithium disilicate ceramics (n = 21 per group) and cemented on customized zirconia abutments by using two provisional resin cements of TempBond Clear and Implantlink Semi, and TempBond serving as the control (n = 7 per cement subgroup). The specimens’ color was measured before and after cementation and after thermocycling. The color difference was calculated by using CIEDE2000 formula (ΔE00). The tensile force was applied to assess the retentive strength. Kruskal-Wallis, Dunn’s post-hoc, and Mann-Whitney non-parametric tests were used to compare ΔE00(1) and ΔE00(2) and two-way ANOVA followed by one-way ANOVA and Tukey’s HSD post hoc test and T-test were used to compare retentive strength between subgroups. In the lithium disilicate group, ΔE00 of the control subgroup (TempBond) was significantly higher than that of Implantlink Semi cements subgroup (P = 0.001). But, in the monolithic zirconia group, ΔE00 of the control subgroup (TempBond) was significantly higher than that of Implantlink Semi (P = 0.020) and TempBond Clear cements (P = 0.007). In the monolithic zirconia group, the control subgroup (TempBond) was significantly more retentive than TempBond Clear (P = 0.003) and Implantlink Semi cement (P = 0.001). However, in the lithium disilicate group, Implantlink Semi cement was significantly more retentive than TempBond Clear (P = 0.019) and TempBond (control) (P = 0.001). The final color of both restorations was significantly affected by the provisional resin cement type. The retentive strength was influenced by both the type of cement and ceramic.

Titanium specimens have been proven to be safe and effective biomaterials in terms of their osseo-integration. To improve the bioactivity and develop customized implants titanium, the surface can be modified with selective laser melting (SLM). Moreover, the design of macro-porous structures has become popular for reaching a durable bone fixation. 3D-printed titanium (Titanium A, B, and C), were cleaned using an organic acid treatment or with electrochemical polishing, and were characterized in terms of their surface morphology using scanning electron microscopy. Next, Dental Pulp Stem Cells (DPSCs) were cultured on titanium in order to analyze their biocompatibility, cell adhesion, and osteoconductive properties. All tested specimens were biocompatible, due to the time-dependent increase of DPSC proliferation paralleled by the decrease of LDH released. Furthermore, data highlighted that the open cell form with interconnected pores of titanium A, resembling the inner structure of the native bone, allows cells to better adhere inside the specimen, being proteins related to cell adherence highly expressed. Likewise, titanium A displays more suitable osteoconductive properties, being the profile of osteogenic markers improved compared to titanium B and C. The present work has demonstrated that the inner design and post-production treatments on titanium surfaces have a dynamic influence on DPSC behavior toward adhesion and osteogenic commitment.

Laser processing of dental implant surfaces is becoming a more widespread replacement for classical techniques due to its undeniable advantages, including control of oxide formation and structure and surface relief at the microscale. Thus, using a laser, we created several biomimetic topographies of various shapes on the surface of titanium screw-shaped implants to research their success and survival rates. A distinctive feature of the topographies is the presence of “µ-rooms”, which are special spaces created by the depressions and elevations and are analogous to the µ-sized room in which the osteocyte will potentially live. We conducted the comparable in vivo study using dental implants with continuous (G-topography with µ-canals), discrete (S-topography with μ-cavities), and irregular (I-topography) laser-induced topographies. A histological analysis performed with the statistical method (with p-value less than 0.05) was conducted, which showed that G-topography had the highest BIC parameter and contained the highest number of mature osteocytes, indicating the best secondary stability and osseointegration.

Objectives: To evaluate the effect of cone-beam computed tomography (CBCT) tube current (mA) on the magnitude of artefacts at different distances from titanium or zirconia implants, with and without activation of a proprietary metal artefact reduction (MAR). Material and methods: Human mandibles were scanned on an OP300 Maxio CBCT unit (Instrumentarium, Tuusula, Finland) before and after the installation of dental implants, with four different tube currents (4 mA, 6.3 mA, 8 mA and 10 mA), with and without activation of proprietary MAR. The effect of mA on the standard deviation (SD) of gray values and contrast to noise ratio (CNR) were assessed in regions of interest located 1.5 cm, 2.5 cm, and 3.5 cm from implants. Results: In the presence of titanium implants, a significant decrease in SD was found by increasing tube current from 4 mA to 6.3 mA or 8 mA. For zirconia implants, 8 mA yielded better results for all distances. MAR improved CNR in the presence of zirconia implants at all distances, whereas no differences were observed with the use of MAR for titanium implants. Conclusion: Increased tube current can improve overall image quality in the presence of implants, at all the distances tested. When a zirconia implant is present, such increase in mA should be higher in comparison to that for examinations with titanium implants. Activation of OP300 Maxio proprietary MAR improved image quality only among examinations with zirconia implants. Clinical relevance: Artefact-generating implants are common in the field of view of CBCT examinations. Optimal exposure parameters, such as tube current, ensure high image quality with lowest possible radiation exposure.

Osseointegration of dental, craniofacial, and orthopedic implants is critical for their long-term success. Multifunctional surface treatment of implants was found to significantly improve cell adhesion and induce osteogenic differentiation of dental-derived stem cells in vitro. Moreover, local and sustained release of antibiotics via nanolayers from the surface of implants can present unparalleled therapeutic benefits in implant dentistry. Here, we present a layer-by-layer surface treatment of titanium implants capable of incorporating BMP-2–mimicking short peptides and gentamicin to improve their osseointegration and antibacterial features. Additionally, instead of conventional surface treatments, we employed polydopamine coating before layer-by-layer assembly to initiate the formation of the nanolayers on rough titanium surfaces. Cytocompatibility analysis demonstrated that modifying the titanium implant surface with layer-by-layer assembly did not have adverse effects on cellular viability. The implemented nanoscale coating provided sustained release of osteoinductive peptides with an antibacterial drug. The surface-functionalized implants showed successful osteogenic differentiation of periodontal ligament stem cells and antimicrobial activity in vitro and increased osseointegration in a rodent animal model 4 wk postsurgery as compared with untreated implants. Altogether, our in vitro and in vivo studies suggest that this approach can be extended to other dental and orthopedic implants since this surface functionalization showed improved osseointegration and an enhanced success rate.

Dental implants are the usual therapy of choice in the dental clinic to replace a loss of natural teeth. Over recent decades there has been an important progress in the design and manufacturing of titanium implant surfaces with the goal of improving their osteointegration. In the present work, the aim was to evaluate the usefulness of hDPSCs (human dental pulp stem cells), in combination with autologous plasma components, for in vitro bone generation on biomimetic titanium dental implant materials. In this context, the combination of hDPSCs stimulated by PRGF or PRF and cultured on standard Ti6A14V and biomimetic BAS™ (Avinent Implant System) titanium surfaces were studied in order to evaluate possible enhancements in the osteoblastic differentiation process out of human mesenchymal cells, as well as bone matrix secretion on the implant surface. The results obtained in this in vitro model of osteogenesis suggested a combination of biomimetic rough titanium surfaces, such as BAS™, with autologous plasma-derived fibrin-clot membranes such as PRF and/or insoluble PRGF formulations, but not with an addition of water-soluble supplements of plasma-derived growth factors, to maximise osteoblastic cell differentiation, bone generation, anchorage and osteointegration of titanium-made dental implants.

Aim. To study the effect of exometabolites of Bifidobacterium bifidum on the biological properties of causative agents of purulent-septic complications in trauma and orthopedic practice and to evaluate their effect on reparative bone tissue regeneration in the peri-implant zone in the postoperative period. Materials and methods. Using the museum cultures of B. bifidum 791, S. aureus 25923 ATCC, P. aeruginosa 27853 ATCC and antibiotic-resistant hospital strains, isolated from patients with periprosthetic infection and osteomyelitis (S.aureus 889, S. epidermidis 2041, P. aeruginosa 9672). The supernatant (exometabolites) of B. bifidum 791 was obtained from a broth culture, which was centrifuged and passed through a membrane filter. In studying the effect of exometabolites of bifidobacteria on the proliferative activity of bacteria, the two-day supernatant of B. bifidum was co-incubated for 24 cultures of museum and hospital strains. The biofilm formation in vitro experiment was studied after 24 and 96 hours. Treatment of implants with exometabolites of bifidobacteria was carried out for 30 minutes. Experimental research was carried out on rabbits of breed «Flandr». Titanium implants without coating (control) and with porous SBKFM coating treated with exometabolites of B. bifidum (experiment) were screwed into the tibial bones of animals. Histological examination and computed microtomography were performed using a SkyScan 1172 instrument (BRUKER). Result. Depending on the time of cultivation of bifidobacteria, the supernatant B. bifidum 791 had a bacteriostatic and bactericidal effect to varying degrees, and also inhibited the biofilm formation of the studied microorganism cultures, including antibiotic-resistant strains. In in vivo experiments, the use of porous SBKFM coatings on titanium implants treated with the supernatant of bifidobacteria made it possible to maintain the mineral density indices of the peri-implantation zone at a high level in comparison with the use of control titanium implants without coating. Conclusion. Positive results of preclinical experiments are promising for further clinical research in trauma and orthopedic practice, which ultimately will reduce the risk of developing septic complications and prevent the migration of metal structures and instability of endoprostheses in the postoperative period.

Purpose of the study – to evaluate the antibacterial activity and biological compatibility of alloy coatings based on two-dimensionally ordered linear chain carbon (TDOLCC).Materials and Methods. Coatings based on TDOLCC were synthesized using alloying additions like nitrogen (TDOLCC+N) and silver (TDOLCC+Ag) on the surfaces of titanium plates and polystyrene plates by the ion-stimulated carbon condensation in a vacuum. The authors examined the superficial bactericidal activity of the coatings and its resistance to mechanical effects. Coated plates were evaluated in respect of rate of microbial biofilms formation by clinical isolates with multiple and extreme antibiotic resistance. Specimens were colored with crystal violet solution to visualize the biofilms. Cytotoxic effect of coatings was evaluated in respect of primary culture of fibroblasts and keratinocyte cell line HaCaT.Results. The authors observed pronounced superficial bactericidal effect of TDOLCC+Ag coating in respect of microorganisms of several taxonomic groups independently of their resistance to antibacterial drugs. TDOLCC+Ag coating proved capable to completely prevent microbial biofilm formation by antibiotic resistant clinical isolates of S. aureus and P. aeruginosa. Silvercontaining coating demonstrated mechanical resistance and preservation of close to baseline level of superficial bactericidal activity even after lengthy abrasion treatment. TDOLCC based coatings did not cause any cytotoxic effects. Structure of monolayers formed in cavities coated by TDOLCC+N and TDOLCC+Ag was indistinguishable from the monolayers in cavities of control plates.

Daniel Oltean-Dan,1 Gabriela-Bombonica Dogaru,2 Maria Tomoaia-Cotisel,3,4Dragos Apostu,1 Alexandru Mester,5 Horea-Rares-Ciprian Benea,1 Mihai-Gheorghe Paiusan,1 Elena-Mihaela Jianu,6 Aurora Mocanu,3 Reka Balint,3 Catalin-Ovidiu Popa,7 Cristian Berce,8 Gyorgy-Istvan Bodizs,9 Alina-Mihaela Toader,10 Gheorghe Tomoaia1,41Iuliu Hatieganu University of Medicine and Pharmacy, Department of Orthopedics and Traumatology, 400132 Cluj-Napoca, Romania; 2Iuliu Hatieganu University of Medicine and Pharmacy, Department of Medical Rehabilitation, 400347 Cluj-Napoca, Romania; 3Babes Bolyai University, Faculty of Chemistry and Chemical Engineering, Department of Chemical Engineering, Research Center of Physical Chemistry, 400028 Cluj-Napoca, Romania; 4Academy of Romanian Scientists, 050085 Bucharest, Romania; 5Iuliu Hatieganu University of Medicine and Pharmacy, Department of Oral Rehabilitation, Oral Health and Management, 400012 Cluj-Napoca, Romania; 6Iuliu Hatieganu University of Medicine and Pharmacy, Department of Histology, 400349 Cluj-Napoca, Romania; 7Technical University of Cluj-Napoca, Department of Materials Science and Engineering, 400641 Cluj-Napoca, Romania; 8Iuliu Hatieganu University of Medicine and Pharmacy, Center for Experimental Medicine, 400349 Cluj-Napoca, Romania; 9Rehabilitation Clinic, 400347 Cluj-Napoca, Romania; 10Iuliu Hatieganu University of Medicine and Pharmacy, Department of Physiology, 400006 Cluj-Napoca, RomaniaPurpose: Bone consolidation after severe trauma is the most challenging task in orthopedic surgery. This study aimed to develop biomimetic composite for coating Ti implants. Afterwards, these implants were testedin vivo to assess bone consolidation in the absence or the presence of high-frequency pulsed electromagnetic short-waves (HF-PESW).Materials: Biomimetic coating was successfully developed using multi-substituted hydroxyapatite (ms-HAP) functionalized with collagen (ms-HAP/COL), embedded into poly-lactic acid (PLA) matrix (ms-HAP/COL@PLA), and subsequently covered with self-assembled COL layer (ms-HAP/COL@PLA/COL, named HAPc).Methods: For in vivo evaluation, 32 Wistar albino rats were used in four groups: control group (CG) with Ti implant; PESW group with Ti implant+HF-PESW; HAPc group with Ti implant coated with HAPc; HAPc+PESW group with Ti implant coated with HAPc+HF-PESW. Left femoral diaphysis was fractured and fixed intramedullary. From the first post-operative day, PESW and HAPc+PESW groups underwent HF-PESW stimulation for 14 consecutive days. Biomimetic coating was characterized by XRD, HR-TEM, SEM, EDX and AFM.Results: Osteogenic markers (ALP and osteocalcin) and micro-computed tomography (CT) analysis (especially bone volume/tissue volume ratio results) indicated at 2 weeks the following group order: HAPc+PESW>HAPc≈PESW (P>0.05) and HAPc+PESW>control (P

Daniel Oltean-Dan,1 Gabriela-Bombonica Dogaru,2 Maria Tomoaia-Cotisel,3,4Dragos Apostu,1 Alexandru Mester,5 Horea-Rares-Ciprian Benea,1 Mihai-Gheorghe Paiusan,1 Elena-Mihaela Jianu,6 Aurora Mocanu,3 Reka Balint,3 Catalin-Ovidiu Popa,7 Cristian Berce,8 Gyorgy-Istvan Bodizs,9 Alina-Mihaela Toader,10 Gheorghe Tomoaia1,41Iuliu Hatieganu University of Medicine and Pharmacy, Department of Orthopedics and Traumatology, 400132 Cluj-Napoca, Romania; 2Iuliu Hatieganu University of Medicine and Pharmacy, Department of Medical Rehabilitation, 400347 Cluj-Napoca, Romania; 3Babes Bolyai University, Faculty of Chemistry and Chemical Engineering, Department of Chemical Engineering, Research Center of Physical Chemistry, 400028 Cluj-Napoca, Romania; 4Academy of Romanian Scientists, 050085 Bucharest, Romania; 5Iuliu Hatieganu University of Medicine and Pharmacy, Department of Oral Rehabilitation, Oral Health and Management, 400012 Cluj-Napoca, Romania; 6Iuliu Hatieganu University of Medicine and Pharmacy, Department of Histology, 400349 Cluj-Napoca, Romania; 7Technical University of Cluj-Napoca, Department of Materials Science and Engineering, 400641 Cluj-Napoca, Romania; 8Iuliu Hatieganu University of Medicine and Pharmacy, Center for Experimental Medicine, 400349 Cluj-Napoca, Romania; 9Rehabilitation Clinic, 400347 Cluj-Napoca, Romania; 10Iuliu Hatieganu University of Medicine and Pharmacy, Department of Physiology, 400006 Cluj-Napoca, RomaniaPurpose: Bone consolidation after severe trauma is the most challenging task in orthopedic surgery. This study aimed to develop biomimetic composite for coating Ti implants. Afterwards, these implants were testedin vivo to assess bone consolidation in the absence or the presence of high-frequency pulsed electromagnetic short-waves (HF-PESW).Materials: Biomimetic coating was successfully developed using multi-substituted hydroxyapatite (ms-HAP) functionalized with collagen (ms-HAP/COL), embedded into poly-lactic acid (PLA) matrix (ms-HAP/COL@PLA), and subsequently covered with self-assembled COL layer (ms-HAP/COL@PLA/COL, named HAPc).Methods: For in vivo evaluation, 32 Wistar albino rats were used in four groups: control group (CG) with Ti implant; PESW group with Ti implant+HF-PESW; HAPc group with Ti implant coated with HAPc; HAPc+PESW group with Ti implant coated with HAPc+HF-PESW. Left femoral diaphysis was fractured and fixed intramedullary. From the first post-operative day, PESW and HAPc+PESW groups underwent HF-PESW stimulation for 14 consecutive days. Biomimetic coating was characterized by XRD, HR-TEM, SEM, EDX and AFM.Results: Osteogenic markers (ALP and osteocalcin) and micro-computed tomography (CT) analysis (especially bone volume/tissue volume ratio results) indicated at 2 weeks the following group order: HAPc+PESW>HAPc≈PESW (P>0.05) and HAPc+PESW>control (P

Studying of anodic titania formation has showen that anodization forming factor at low anodic voltages is 3,3 nm/V, while at high anodic voltages it’s value decreases till 1,5 nm/V. The investigation of optical properties of anodic titania has showed the possibilities to tune the titania refractory index in the whole visible ranges. The application of anodic titania in maxillofacial surgery has been demonstrated for visualization of titanium objects.

The aim of this study was to form a functional layer on the surface of titanium (Ti) implants to enhance their bioactivity. Layers of polyurethane (PU), containing hydroxyapatite (HAp) nanoparticles (NPs) and magnesium (Mg) particles, were deposited on alkali-treated Ti surfaces using a cost-effective dip-coating approach. The coatings were assessed in terms of morphology, chemical composition, adhesion strength, interfacial bonding, and thermal properties. Additionally, cell response to the variably coated Ti substrates was investigated using MC3T3-E1 osteoblast-like cells, including assessment of cell adhesion, cell proliferation, and osteogenic activity through an alkaline phosphatase (ALP) assay. The results showed that the incorporation of HAp NPs enhanced the interfacial bonding between the coating and the alkali-treated Ti surface. Furthermore, the presence of Mg and HAp particles enhanced the surface charge properties as well as cell attachment, proliferation, and differentiation. Our results suggest that the deposition of a bioactive composite layer containing Mg and HAp particles on Ti implants may have the potential to induce bone formation.

Preparation of paraspinal tissue of patients with implants for elemental analysis is a challenge because it contains titanium in the ionic form, as well as metallic debris. Most literature reports focus on dissolving the tissue, but the impact of digestion conditions on metallic debris of Ti has not been investigated. In our work, various digestion conditions, including systems, compositions of oxidising mixture, and time, were tested aiming (i) to digest the tissue without digestion of metallic titanium to quantify soluble Ti and (ii) to digest metallic titanium debris to asses total Ti content in tissue. The experiments were performed in a closed mode using a microwave-assisted system and a carbon heating block. Our study revealed that total digestion of titanium was impossible in the tested conditions and the maximal level of digested titanium was below 70%. The mineralisation with the use of concentrated nitric acid was optimal to prepare paraspinal samples to analyse the soluble titanium form because metallic titanium passivated and did not migrate to the solution. The elaborated conditions were applied to determine titanium ion in the periimplant tissue of patients with three different titanium-based surgical systems, including traditional growing rod (TGR), guided growth systems (GGS), and vertical expandable prosthesis titanium rib (VEPTR).

This study aimed to analyze fracture strength in vitro by varying the axial height of the titanium insert and the labial height of the zirconia abutment in an internal connection implant to identify the titanium insert axial height with optimal mechanical stability. Sixty implants with an internal connection system were used. Two-piece zirconia abutments were used with the titanium inserts. Combinations of different titanium insert axial heights (mm) and zirconia abutment labial heights (mm) constituted five groups: Gr1 (1–3), Gr2 (3–3), Gr3 (3–5), Gr4 (5–3), and Gr5 (5–5). After thermocycling, a fracture load test was performed with a universal testing machine. The initial deformation load and the fracture load were measured and analyzed. The fractured surface and cross-section of the specimens were examined by scanning electron microscopy (SEM). The groups of titanium inserts with axial heights of 3 mm and 5 mm showed significantly greater initial deformation load and fracture load than the group with an axial height of 1 mm (p < 0.05), but there was no significant difference between the two groups with axial heights of 3 mm and 5 mm. The labial height of the zirconia abutment had no significant influence on the initial deformation load and fracture load. In some specimens in Gr4 and Gr5, cracking or bending of the titanium insert and abutment screw was observed on SEM. The axial height of the titanium insert should be designed to not be less than 3 mm to increase the fracture strength and promote the long-term stability of implants.

The surface modification of titanium (Ti) can enhance the osseointegration and antibacterial properties of implants. In this study, we modified porous Ti discs with calcium phosphate (CaP) and different concentrations of Lactoferrin (LF) by biomimetic mineralization and examined their antibacterial effects and osteogenic bioactivity. Firstly, scanning electron microscopy (SEM), the fluorescent tracing method, X-ray photoelectron spectroscopy (XPS), Fourier transform infrared spectroscopy (FTIR), energy dispersive X-ray spectroscopy (EDX), X-ray diffraction (XRD), and the releasing kinetics of LF were utilized to characterize the modified Ti surface. Then, the antibacterial properties against S. sanguis and S. aureus were investigated. Finally, in vitro cytological examination was performed, including evaluations of cell adhesion, cell differentiation, extracellular matrix mineralization, and cytotoxicity. The results showed that the porous Ti discs were successfully modified with CaP and LF, and that the LF-M group (200 μg/mL LF in simulated body fluid) could mildly release LF under control. Further, the LF-M group could effectively inhibit the adhesion and proliferation of S. sanguis and S. aureus and enhance the osteogenic differentiation in vitro with a good biocompatibility. Consequently, LF-M-modified Ti may have potential applications in the field of dental implants to promote osseointegration and prevent the occurrence of peri-implantitis.

Background: Concepts of Chiari malformation Type 1 (CM1) surgery in the present time significantly different. The most common complications are pseudomeningocele (12%) and postoperative CSF leak (5%). The development of pseudomeningocele may be associated with inappropriate restoration of bone and muscles relations. Methods: The pilot study involved 11 patients aged 24–64 years with a diagnosis of CM1 who had indications for surgical treatment. Special titanium implant enabling fixation of the occipital and cervical muscles at the projections of their normal attachments was developed, it was placed to occipital bone on the final stages of surgical intervention. Surgical technique promoted tightened wound closure neutralizing formation of “dead space” at the place of occipital craniectomy and between muscle layers. The implant was produced by direct metal laser sintering method for each patient individually. Results: There were no complications during the hospitalization and follow-up period. Postoperative MRI demonstrated adequate formation of the cisterna magna and the absence of pseudomeningocele. During follow-up period there were no signs of pseudomeningocele, CSF leak, surgical scar complications, implant-associated infections, and other complications. Conclusion: In the study group, no pseudomeningocele cases as long as any other complications associated with surgery had been revealed. The efficacy of the proposed surgical technique using the developed implant should be evaluated in clinical trials with larger patient samples. To simplify preoperative planning and manufacturing of the implant for each patient individually, a set of implants with different specified sizes was developed.

Dental implants are one of the most frequently used treatment options for tooth replacement, and titanium is the metal of choice due to its demonstrated superiority in resisting corrosion, lack of allergic reactions and mechanical strength. Surface roughness of titanium implants favors the osseointegration process, nevertheless, its topography may provide a suitable substrate for bacterial biofilm deposition, causing peri-implantitis and leading to implant failure. Subgingival prophylaxis treatments with cleansing powders aimed to remove the bacterial accumulation are under investigation. Two different air-polishing powders&mdash, glycine and tagatose&mdash, were assayed for their cleaning and antimicrobial potential against a Pseudomonas biofilm and for their effects on human dental pulp stem cells (hDPSCs), seeded on sandblasted titanium disks. Immunofluorescence analyses were carried out to evaluate cell adhesion, proliferation, stemness and osteogenic differentiation. The results demonstrate that both the powders have a great in vitro cleaning potential in the early period and do not show any negative effects during hDPSCs osteogenic differentiation process, suggesting their suitability for enhancing the biocompatibility of titanium implants. Our data suggest that the evaluated cleansing systems reduce microbial contamination and allow us to propose tagatose as an adequate alternative to the gold standard glycine for the air-polishing prophylaxis treatment.

International audience; The paper investigates how the surface relief of an implant affects cell behavior. Currently, most implant manufacturers claim the key impact biocompatibility factor to be surface micro-roughness. We suppose that the interaction between cells and implants also depends on such relief peculiarities as continuous or discontinuous topography, subcellular distance between peaks and presence of porous oxide layer. We have developed the laser processing conditions that provide three different reliefs: «open grooves», «grid» and «close grooves». Along with the micro-roughness characteristics the reliefs differ with their deepness and period of grooves. The surface composition analysis results have shown a sandwich structure consisting of Ti → TiO → Ti 2 O 3 Nx → TiO 2 (anatase) → TiO 2 (rutile). The wettability study has demonstrated superhydrophilicity (CA is 0 •) for all reliefs. The quantitative and qualitative analysis of hMSCs proliferation and osteogenic differentiation was performed for 20 days. In vitro study has revealed the topography affects the spatial orientation of cells. The shape and size of the cell nuclei vary with different topographies. We have found continuous «open grooves» structures with the subcellular to cellular period are beneficial for cells' life-sustaining activity. Discontinuous «grid» structures with individual slots might not provide cells with mobility with the least external mechanical effect compared to «open grooves».

Featured Application In this paper, a fast, one-step method to prepare acrylate-based coatings on titanium through the atmospheric pressure plasma polymerization of HEMA is described. The coating shows lower surface bacterial adhesion and enhanced cell adhesion when compared with pristine titanium. Dental implants can fail due to various factors, in which bad tissue integration is believed to have a significant role. Specific properties of the implant surface, such as its chemistry and roughness, are of paramount importance to address specific cell responses, such as the adsorption of proteins, as well as the adhesion and differentiation of cells, which are suitable for biomaterial and tissue engineering. In this study, an acrylate-containing coating was produced on titanium surfaces through the atmospheric pressure plasma treatment of a liquid precursor, 2-hydroxyethyl methacrylate. A hydrophilic coating was obtained, showing retention of the monomer chemistry as assessed by FTIR analysis and XPS. Enhanced fibroblast adhesion and decreased Staphylococcus aureus and Escherichia coli adhesion were recorded, showing that this is a suitable method to produce biocompatible coatings with a reduced bacterial adhesion.

Metallic implants are widely used in diverse clinical applications to aid in recovery from lesions or to replace native hard tissues. However, the lack of integration of metallic surfaces with soft tissue interfaces causes the occurrence of biomaterial-associated infections, which can trigger a complicated inflammatory response and, ultimately, implant failure. Here, a multifunctional implant surface showing nanoscale anisotropy, based on the controlled deposition of cellulose nanocrystals (CNC), and biological activity derived from platelet lysate (PL) biomolecules sequestered and presented on CNC surface, is proposed. The anisotropic radial nanopatterns are produced on polished titanium surfaces by spin-coating CNC at high speed. Furthermore, CNC surface chemistry allows to further sequester and form a coating of bioactive molecules derived from PL. The surface anisotropy provided by CNC guides fibroblasts growth and alignment up to 14 days of culture. Moreover, PL-derived biomolecules polarize macrophages toward the M2-like anti-inflammatory phenotype. These results suggest that the developed multifunctional surfaces can promote soft tissue integration to metallic implants and, at the same time, prevent bacterial invasion, tissue inflammation, and failure of biomedical metallic implants., International Team for Implantology – ITI Research grant 1306_2018; and from Fundação para a Ciência e a Tecnologia (FCT) for CEECIND/01375/2017

Cellularized scaffold is emerging as the preferred solution for tissue regeneration and restoration of damaged functionalities. However, the high cost of preclinical studies creates a gap between investigation and the device market for the biomedical industry. In this work, bone-tailored scaffolds based on the Ti6Al4V alloy manufactured by electron beam melting (EBM) technology with reused powder were investigated, aiming to overcome issues connected to the high cost of preclinical studies. Two different elementary unit cell scaffold geometries, namely diamond (DO) and rhombic dodecahedron (RD), were adopted, while surface functionalization was performed by coating scaffolds with single layers of polycaprolactone (PCL) or with mixture of polycaprolactone and 20 wt.% hydroxyapatite (PCL/HA). The mechanical and biological performances of the produced scaffolds were investigated, and the results were compared to software simulation and experimental evidence available in literature. Good mechanical properties and a favorable environment for cell growth were obtained for all combinations of scaffold geometry and surface functionalization. In conclusion, powder recycling provides a viable practice for the biomedical industry to strongly reduce preclinical costs without altering biomechanical performance.