Search

This paper presents an investigation of the potential to use aligned discontinuous carbon fiber dry prepregs as electrodes in structural supercapacitors (SSCs). The high fiber-matrix interfacial bonding of the structural composite was achieved by adopting a solid polymer electrolyte, consisting of poly(vinylidene), lithium triflate, and epoxy. Processing of the SSC was carried out via dip-coating of the polymer electrolyte and then cured using a vacuum bag. The electrochemical performance of the SSCs was measured before and after mechanical loading. The microstructures of the SSCs as-fabricated and damaged under flexural loading were identified by μ-CT imaging. An SSC with a specific capacitance of 0.128 mF/cm2(11.62 mF/g), a flexural strength of 47.49 MPa, and a flexural modulus of 8.48 GPa has been achieved, demonstrating significant improvements in mechanical properties over those of SSCs based on woven carbon fiber fabric-based electrodes. The mechanical behavior of the supercapacitors was evaluated by both quasi-static and cyclic flexural loading tests. The excellent electrochemical stability of the supercapacitors was validated by a capacitance retention of above 96% under galvanostatic charge–discharge cycling tests. The knowledge gained in this work will benefit future research in the optimization of SSC performance.

Thick electrode with high-areal-capacity is a practical and promising strategy to increase the energy density of batteries, but development toward thick electrode is limited by the electrochemical performance, mechanical properties, and manufacturing approaches. In this work, we overcome these limitations and report an ultrathick electrode structure, called fiber-aligned thick or FAT electrode, which offers a novel electrode design and a scalable manufacturing strategy for high-areal-capacity battery electrodes. The FAT electrode uses aligned carbon fibers to construct a through-thickness fiber-aligned electrode structure with features of high electrode material loading, low tortuosity, high electrical and thermal conductivity, and good compression property. The low tortuosity of FAT electrode enables fast electrolyte infusion and rapid electron/ion transport, exhibiting a higher capacity retention and lower charge transfer resistance than conventional slurry-casted thick electrode design.

The emergence of stretchable electronic devices has attracted intensive attention. However, most of the existing stretchable electronic devices can generally be stretched only in one specific direction and show limited specific capacitance and energy density. Here, we report a stretchable isotropic buckled carbon nanotube (CNT) film, which is used as electrodes for supercapacitors with low sheet resistance, high omnidirectional stretchability, and electro-mechanical stability under repeated stretching. After acid treatment of the CNT film followed by electrochemical deposition of polyaniline (PANI), the resulting isotropic buckled acid treated CNT@PANI electrode exhibits high specific capacitance of 1147.12 mF cm–2at 10 mV s–1. The supercapacitor possesses high energy density from 31.56 to 50.98 μWh cm–2and corresponding power density changing from 2.294 to 28.404 mW cm–2at the scan rate from 10 to 200 mV s–1. Also, the supercapacitor can sustain an omnidirectional strain of 200%, which is twice the maximum strain of biaxially stretchable supercapacitors based on CNT assemblies reported in the literature. Moreover, the capacitive performance is even enhanced to 1160.43–1230.61 mF cm–2during uniaxial, biaxial, and omnidirectional elongations.

The transport of fluid, nutrients, and signaling molecules in the bone lacunar–canalicular system (LCS) is critical for osteocyte survival and function. We have applied the fluorescence recovery after photobleaching (FRAP) approach to quantify load-induced fluid and solute transport in the LCS in situ, but the measurements were limited to cortical regions 30–50 μm underneath the periosteum due to the constrains of laser penetration. With this work, we aimed to expand our understanding of load-induced fluid and solute transport in both trabecular and cortical bone using a multiscaled image-based finite element analysis (FEA) approach. An intact murine tibia was first re-constructed from microCT images into a three-dimensional (3D) linear elastic FEA model, and the matrix deformations at various locations were calculated under axial loading. A segment of the above 3D model was then imported to the biphasic poroelasticity analysis platform (FEBio) to predict load-induced fluid pressure fields, and interstitial solute/fluid flows through LCS in both cortical and trabecular regions. Further, secondary flow effects such as the shear stress and/or drag force acting on osteocytes, the presumed mechano-sensors in bone, were derived using the previously developed ultrastructural model of Brinkman flow in the canaliculi. The material properties assumed in the FEA models were validated against previously obtained strain and FRAP transport data measured on the cortical cortex. Our results demonstrated the feasibility of this computational approach in estimating the fluid flux in the LCS and the cellular stimulation forces (shear and drag forces) for osteocytes in any cortical and trabecular bone locations, allowing further studies of how the activation of osteocytes correlates with in vivo functional bone formation. The study provides a promising platform to reveal potential cellular mechanisms underlying the anabolic power of exercises and physical activities in treating patients with skeletal deficiencies.