Search

Thermophotovoltaics, devices that convert thermal infrared photons to electricity, offer a key pathway for a variety of critical renewable energy technologies including thermal energy storage, waste heat recovery, and direct solar-thermal power generation. However, conventional far-field devices struggle to generate reasonable powers at lower temperatures. Near-field thermophotovoltaics provide a pathway to substantially higher powers by leveraging photon tunneling effects. Here we present a large area near-field thermophotovoltaic device, created with an epitaxial co-fabrication approach, that consists of a self-supported 0.28 cm2 emitter-cell pair with a 150 nm gap. The device generates 1.22 mW at 460 C, a twenty-five-fold increase over the same cell measured in a far-field configuration. Furthermore, the near-field device demonstrates short circuit current densities greater than the far-field photocurrent limit at all the temperatures tested, confirming the role of photon tunneling effects in the performance enhancement. Modeling suggests several practical directions for cell improvements and further increases in power density. These results highlight the promise of near-field thermophotovoltaics, especially for low temperature applications.

We present inverted metamorphic Ga0.3In0.7As photovoltaic converters with sub-0.60 eV bandgaps grown on InP and GaAs substrates. The compositionally graded buffers in these devices have threading dislocation densities of 1.3x10^6 cm^-2 and 8.9x10^6 cm^-2 on InP and GaAs, respectively. The devices generate open-circuit voltages of 0.386 V and 0.383 V, respectively, at a current density of ~10 A/cm^2, yielding bandgap-voltage offsets of 0.20 and 0.21 V. We measured their broadband reflectance and used it to estimate thermophotovoltaic efficiency. The InP-based cell is estimated to yield 1.09 W/cm^2 at 1100 degrees C vs. 0.92 W/cm^2 for the GaAs-based cell, with efficiencies of 16.8 vs. 9.2%. The efficiencies of both devices are limited by sub-bandgap absorption, with power weighted sub-bandgap reflectances of 81% and 58%, respectively, which we assess largely occurs in the graded buffers. We estimate that the thermophotovoltaic efficiencies would peak at ~1100 degrees C at 24.0% and 20.7% in structures with the graded buffer removed, if previously demonstrated reflectance is achieved. These devices also have application to laser power conversion in the 2.0-2.3 micron atmospheric window. We estimate peak LPC efficiencies of 36.8% and 32.5% under 2.0 micron irradiances of 1.86 W/cm^2 and 2.81 W/cm^2, respectively., Comment: 14 pages, 6 figures

Thermophotovoltaics are promising solid-state energy converters for a variety of applications such as grid-scale energy storage, concentrating solar-thermal power, and waste heat recovery. Here, we report the design, fabrication, and testing of large area (0.8 cm$^2$), scalable, single junction 0.74-eV GaInAs thermophotovoltaic devices reaching an efficiency of 38.8$\pm$2.0% and an electrical power density of 3.78 W/cm$^2$ at an emitter temperature of 1850{\deg}C. Reaching such a high emitter temperature and power density without sacrificing efficiency is a direct result of combining good spectral management with a highly optimized cell architecture, excellent material quality, and very low series resistance. Importantly, fabrication of 12 high-performing devices on a two-inch wafer is shown to be repeatable, and the cell design can be readily transferred to commercial epitaxy on even larger wafers. Further improvements in efficiency can be obtained by using a multijunction architecture, and early results for a two-junction 0.84-eV GaInPAs / 0.74-eV GaInAs device illustrate this promise., Comment: 27 pages, 15 figures

Multijunction solar cell design is guided by both the theoretical optimal bandgap combination as well as the realistic limitations to materials with these bandgaps. For instance, triple-junction III-V multijunction solar cells commonly use GaAs as a middle cell because of its near-perfect material quality, despite its bandgap being higher than optimal for the global spectrum. Here, we modify the GaAs bandgap using thick GaInAs/GaAsP strain-balanced quantum well (QW) solar cells with excellent voltage and absorption. These high-performance QWs are incorporated into a triple-junction inverted metamorphic multijunction device consisting of a GaInP top cell, GaInAs/GaAsP QW middle cell, and lattice-mismatched GaInAs bottom cell, each of which has been highly optimized. We demonstrate triple-junction efficiencies of 39.5% and 34.2% under the global and space spectra, respectively, which are higher than previous record six-junction devices., Comment: Main text: 16 pages, 4 figures. Supplemental text: 12 pages, 7 figures

We report the fabrication and measurement of thermophotovoltaic (TPV) cells with efficiencies of >40%, which is a record high TPV efficiency and the first experimental demonstration of the efficiency of high-bandgap tandem TPV cells. TPV efficiency was determined by simultaneous measurement of electric power output and heat dissipation from the device via calorimetry. The TPV cells are two-junction devices comprising high-quality III-V materials with band gaps between 1.0 and 1.4 eV that are optimized for high emitter temperatures of 1900-2400{\deg}C. The cells exploit the concept of band-edge spectral filtering to obtain high efficiency, using high-reflectivity back surface reflectors to reject unusable sub-bandgap radiation back to the emitter. A 1.4/1.2 eV device reached a maximum efficiency of (41.1 +/- 1)% operating at a power density of 2.39 W/cm2 under an irradiance of 30.4 W/cm2 and emitter temperature of 2400{\deg}C. A 1.2/1.0 device reached a maximum efficiency of (39.3 +/- 1)% operating at a power density of 1.8 W/cm2 under an irradiance of 20.1 W/cm2 and emitter temperature of 2127{\deg}C. These cells can be integrated into a TPV system for thermal energy grid storage (TEGS) to enable dispatchable renewable energy. These new TPV cells enable a pathway for TEGS to reach sufficiently high efficiency and sufficiently low cost to enable full decarbonization of the grid. Furthermore, the high demonstrated efficiency also gives TPV the potential to compete with turbine-based heat engines for large-scale power production with respect to both cost and performance, thereby enabling possible usage in natural gas or hydrogen-fueled electricity production.