Search

Mixed oxides derived from the perovskite structure by combination of A- and B-site elements and by partial substitution of oxygen provide an immense playground of physico-chemical properties. Here, we account for own research conducted at the Paul Scherrer Institute on perovskite-type oxides and oxynitrides used in electrochemical, photo(electro)chemical and catalytic processes aiming at facing energy relevant issues.

Hematite as promising photoanode for solar water splitting suffers from severe bulk and surface charge recombination. This work describes that a protonation-annealing treatment can effectively suppress both bulk and surface charge recombination in hematite. Protons/electrons are electrochemically incorporated into hematite under 0.2 VRHE followed by annealing at 120 oC. The photocurrent density increases from ~0.9 mA cm-2 to 1.8 mA cm-2 at 1.23 VRHE under 1 sun, and further to 2.7 mA cm-2 after loading cobalt phosphate, stabilizing at round 2.4 mA cm-2. A cathodic shift of the onset potential of photocurrent is also observed. H2O2 oxidation, impedance spectroscopy and Mott-Schottky measurements show that the protonation suppresses bulk recombination and enhances donor density, but introducing more surface recombination. The annealing reduces surface recombination, while preserving relatively high bulk charge separation efficiency. Different from previous reports on the electrochemically reduced hematite, this work demonstrates that the performance improvement should be ascribed to the proton incorporation instead of the formation of Fe3O4 or metal Fe. This facile treatment by protonation and annealing could be applied in other semiconductors to promote the development of high performing photoelectrodes.

Perovskite yttrium tantalum oxynitride is theoretically proposed as a promising semiconductor for solar water splitting because of the predicted bandgap and energy positions of band edges. In experiment, however, we show here that depending on processing parameters, yttrium tantalum oxynitrides exist in multiphases, including the desired perovskite YTaON2, defect fluorite YTa(O,N,o)4, and N-doped YTaO4. These multiphases have bandgaps ranging between 2.13 and 2.31 eV, all responsive to visible light. The N-doped YTaO4, perovskite main phase, and fluorite main phase derived from crystalline fergusonite oxide precursors exhibit interesting photoelectrochemical performances for water oxidation, while the defect fluorite derived from low crystallized scheelite-type oxide precursors show negligible activity. Preliminarily measurements show that loading IrOx cocatalyst on N-doped YTaO4 significantly improves its photoelectrochemical performance encouraging further studies to optimize this new material for solar fuel production.

We study the oxo-hexametallate Li$_7$TaO$_6$ with first-principles and classical molecular dynamics simulations, obtaining a low activation barrier for diffusion of $\sim$0.29 eV and a high ionic conductivity of $5.7 \times 10^{-4}$ S cm$^{-1}$ at room temperature (300 K). We find evidence for a wide electrochemical stability window from both calculations and experiments, suggesting its viable use as a solid-state electrolyte in next-generation solid-state Li-ion batteries. To assess its applicability in an electrochemical energy storage system, we performed electrochemical impedance spectroscopy measurements on multicrystalline pellets, finding substantial ionic conductivity, if below the values predicted from simulation. We further elucidate the relationship between synthesis conditions and the observed ionic conductivity using X-ray diffraction, inductively coupled plasma optical emission spectrometry, and X-ray photoelectron spectroscopy, and study the effects of Zr and Mo doping.

Strain engineering is the art of inducing controlled lattice distortions in a material to modify specific physicochemical properties. Strain engineering is applied for basic fundamental studies of physics and chemistry of solids but also for device fabrication through the development of materials with new functionalities. Thin films are one of the most important tools for strain engineering. Thin films can in fact develop large strain due to the crystalline constrains at the interface with the substrate and/or as the result of specific morphological features that can be selected by an appropriate tuning of the deposition parameters. Within this context, the in situ measurement of the substrate curvature is a powerful diagnostic tool allowing a real time monitoring of the stress state of the growing film. This manuscript reviews a few recent applications of this technique and presents new measurements that point out the great potentials of the substrate curvature measurement in strain engineering. Our study also shows how, due to the high sensitivity of the technique, the correct interpretation of the results can be in certain cases not trivial and require complementary characterizations and an accurate knowledge of the physicochemical properties of the materials under investigation.

Multilayered heterostructures of Ce0.85Sm0.15O2-delta and Y0.16Zr0.92O2-delta of a high crystallographic quality were fabricated on (001) - oriented MgO single crystal substrates. Keeping the total thickness of the heterostructures constant, the number of ceria-zirconia bilayers was increased while reducing the thickness of each layer. At each interface Ce was found primarily in the reduced, 3+ oxidation state in a layer extending about 2 nm from the interface. Concurrently, the conductivity decreased as the thickness of the layers was reduced suggesting a progressive confinement of the charge transport along the YSZ layers. The comparative analysis of the in-plane electrical characterization suggests that the contribution to the total electrical conductivity of these interfacial regions is negligible. For the smallest layer thickness of 2 nm the doped ceria layers are electrically insulating and the ionic transport only occurs through the zirconia layers. This is explained in terms of a reduced mobility of the oxygen vacancies in the highly reduced ceria.

Solid oxide oxygen ion and proton conductors are a highly important class of materials for renewable energy conversion devices like solid oxide fuel cells. Ba2In2O5 (BIO) exhibits both oxygen ion and proton conduction, in dry and humid environment, respectively. In dry environment, the brownmillerite crystal structure of BIO exhibits an ordered oxygen ion sublattice, which has been speculated to result in anisotropic oxygen ion conduction. The hydrated structure of BIO, however, resembles a perovskite and the protons in it were predicted to be ordered in layers. To complement the significant theoretical and experimental efforts recently reported on the potentially anisotropic conductive properties in BIO, we measure here the proton and oxygen ion conductivity along different crystallographic directions. Using epitaxial thin films with different crystallographic orientations the charge transport for both charge carriers is shown to be anisotropic. The anisotropy of the oxygen ion conduction can indeed be explained through the layered structure of the oxygen sublattice in brownmillerite BIO. The anisotropic proton conduction however, further supports the suggested ordering of the protonic defects in the material. The differences in proton conduction along different crystallographic directions attributed to proton ordering in BIO are of a similar extent as those observed along different crystallographic directions in materials where proton ordering is not present but where protons find preferential conduction pathways through chain-like or layered structures.

The solar water splitting process assisted by semiconductor photocatalysts attracts growing research interests worldwide for the production of hydrogen as a clean and sustainable energy carrier. Due to their optical and electrical properties several oxynitride materials show great promise for the fabrication of efficient photocatalysts for solar water splitting. This study reports a comparative investigation of particle- and thin films-based photocatalysts using three different oxynitride materials. The absolute comparison of the photoelectrochemical activities favors the particle-based electrodes due to the better absorption properties and larger electrochemical surface area. However, thin films surpass the particle-based photoelectrodes due to their more suitable morphological features that improve the separation and mobility of the photo-generated charge carriers. Our analysis identifies what specific insights into the properties of materials can be achieved with the two complementary approaches.

Photoelectrochemical solar water splitting is a promising approach to convert solar energy into sustainable hydrogen fuel using semiconductor electrodes. Due to their visible light absorption properties, oxynitrides have shown to be attractive photocatalysts for this application. In this study, the influence of the preparation method of CaNbO2N particles on their morphological and optical properties, and thereby their photoelectrochemical performance, is investigated. The best performing CaNbO2N photoanode is produced by ammonolysis of Nb enriched calcium niobium oxide. The enhanced photoactivity arises from an enlarged surface area and superior visible light absorption properties. The photoactivity of this photoanode was further enhanced by photodeposition of Co-Pi co-catalyst and by atomic layer deposition of an Al2O3 overlayer. A photocurrent density of 70 microA.cm-2 at 1.23 V vs RHE was achieved. The observed enhancement of the photoelectrochemical performance after Co-Pi/Al2O3 deposition is the combined effect of the improved kinetics of oxygen evolution due to the Co-Pi co-catalyst and the reduced surface recombination of the photogenerated carriers at the Al2O3 surface layer.

The nitrogen substitution into the oxygen sites of several oxide materials leads to a reduction of the band gap to the visible light energy range, which makes these oxynitride semiconductors potential photocatalysts for efficient solar water splitting. Oxynitrides typically show a different crystal structure compare to the pristine oxide material. Since the band gap is correlated to both the chemical composition and the crystal structure, it is not trivial to distinguish what modifications of the electronic structure induced by the nitrogen substitution are related to compositional and/or structural effects. Here, X-ray emission and absorption spectroscopy is used to investigate the electronic structures of orthorhombic perovskite LaTiOxNy thin films in comparison with films of the pristine oxide LaTiOx with similar orthorhombic structure and cationic oxidation state. Experiment and theory show the expected upward shift in energy of the valence band maximum that reduces the band gap as a consequence of the nitrogen incorporation. But this study also shows that the conduction band minimum, typically considered almost unaffected by the nitrogen substitution, undergoes a significant downward shift in energy. For a rational design of oxynitride photocatalysts the observed changes of both the unoccupied and occupied electronic states have to be taken into account to justify the total band gap narrowing induced by the nitrogen incorporation.

The size of the band gap and the energy position of the band edges make several oxynitride semiconductors promising candidates for efficient hydrogen and oxygen production under solar light illumination. The intense research efforts dedicated to oxynitride materials have unveiled the majority of their most important properties. However, two crucial aspects have received much less attention. One is the critical issue of the compositional/structural surface modifications occurring during operation and how these affect the photoelectrochemical performance. The second concerns the relation between the electrochemical response and the crystallographic surface orientation of the oxynitride semiconductor. These are indeed topics of fundamental importance since it is exactly at the surface where the visible light-driven electrochemical reaction takes place. In contrast to conventional powder samples, thin films represent the best model system for these investigations. This study reviews current state-of-the-art of oxynitride thin film fabrication and characterization before focusing on LaTiO2N selected as representative photocatalyst. We report the investigation of the initial physicochemical evolution of the surface. Then we show that, after stabilization, the absorbed photon-to-current conversion efficiency of epitaxial thin films can differ by about 50% for different crystallographic surface orientations and be up to 5 times larger than for polycrystalline samples.