Search

All-inorganic cesium lead triiodide (CsPbI 3 ) perovskite has received increasing attention due to its intrinsic thermal stability and suitable band gap for photovoltaic applications. However, it is difficult to deposit high-quality pure-phase CsPbI 3 films using CsI and PbI 2 as precursors due to the rapid nucleation and crystal growth by the solution coating method. Here, a simple cation-exchange approach is employed to fabricate all-inorganic 3D CsPbI 3 perovskite, where 1D ethylammonium lead (EAPbI 3 ) perovskite is first solution-deposited and then transformed to 3D CsPbI 3 via ion exchange between EA + and Cs + during thermal annealing. The large space between the PbI 3 - skeletons in 1D EAPbI 3 favors the cation interdiffusion and exchange for the formation of pure-phase 3D CsPbI 3 with full compactness and high crystallinity and orientation. The resulting CsPbI 3 film exhibits a low trap density of state and high charge mobility, and the perovskite solar cell shows a power-conversion efficiency of 18.2% with enhanced stability. This strategy provides an alternative and promising fabrication route for the fabrication of high-quality all-inorganic perovskite devices.

Alkali-exchanged SSZ-13 adsorbents were investigated for their applicability in separating N 2 from CO 2 in flue gas streams using a dynamic breakthrough method. In contrast to IAST calculations based on equilibrium isotherms, K + exchanged SSZ-13 was found to yield the best N 2 productivity, comparable to Ni-MOF-74, under dynamic conditions where diffusion properties play a significant role. This was attributed to the selective, partial blockage of access to the chabazite cavities, enhancing the separation potential in a 15/85 CO 2 /N 2 binary gas mixture.

Fabrication of membrane adsorbers with elevated binding capacity and high throughput is highly desired for simplifying and improving purification efficiencies of bioproducts (biotherapeutics, vaccines, etc.) in the biotechnological and biopharmaceutical industries. Here we demonstrate the preparation of a novel class of self-supported, cellulose-graft-polypropionic acid (CL-g-PPA) cation-exchange nanofiber membrane adsorbers under mild reaction conditions for the purification of positively charged therapeutic proteins. In our fabrication method, acrylonitrile was first polymerized and surface grafted onto cellulose nanofibers using cerium ammonium nitrate as a redox initiator to form cellulose-g-polyacrylonitrile (CL-g-PAN). CL-g-PAN was then submitted to a hydrolyzation reaction to form CL-g-PPA cationic membrane adsorbers. Morphology and structural characterization illustrated the formation of CL-g-PPA membranes with uniform coating of polyacid nanolayers along the individual nanofibers without disturbing the nanofiber structure. Benefiting from these numerous cationic polyacid binding sites and inherent large surface area and open porous structure, CL-g-PPA nanofiber membrane adsorbers showed a lysozyme static adsorption capacity of 1664 mg/g of nanofibers. These membranes showed a lysozyme dynamic binding capacity of 508 mg/g of nanofibers at 10% breakthrough (equivalent to 206 g/L capacity), with a residence time of less than 6 s. Moreover, CL-g-PPA self-supported nanofibers displayed excellent structural stability and reversibility after several cycles of protein binding studies. This dynamic binding capacity of the CL-g-PPA nanofiber membranes was 3.2 times higher than that of macroporous cellulose membranes and 8.5 times higher than that of the Sartobind S commercial membrane adsorber. Considering the simple fabrication method employed, excellent protein adsorption capacity, remarkable structural stability, and reusability, CL-g-PPA nanofiber membranes provided a versatile platform for the chromatographic separations of biomolecules (e.g., proteins, nucleic acids, and viral vaccines) as well as water purification and similar ion-exchange applications.

CdS-polyaniline-Pt and ZnS-polyaniline-Pt micromotors have been synthesized and characterized. The nanocrystals are generated "in situ" during the template electrosynthesis of the micromotors while being simultaneously trapped in the polymeric network, generating a hybrid structure. The presence of nanocrystal "edges" in the inner polyaniline layer result in a rough Pt catalytic surface and enhanced electron transfer for highly efficient bubble propulsion at remarkable speeds of over 2500 μm/s. The incorporation of CdS and ZnS nanocrystals impart several attractive functions, including cation-exchange based chemical transformation capabilities and enhanced photocatalytic performance. The remarkable ion-exchange properties of ZnS-polyaniline (PANI)-Pt micromotors are illustrated for the cation exchange of heavy metals cations. The superior photocatalytic performance of CdS-PANI-Pt micromotors is used for the enhanced photocatalytic oxidation of bisphenol A. Such self-propelled micromotors act as highly efficient dynamic platforms that offer significantly shorter and more efficient processes as compared with common static operations. The attractive properties of these micromotors will pave the way for diverse sensing, decontamination, energy generation, or electronic applications.