Search

Abstract: A universal method to obtain record‐high electronic Seebeck coefficients is demonstrated while preserving reasonable conductivities in doped blends of organic semiconductors through rational design of the density of states (DOSs). A polymer semiconductor with a shallow highest occupied molecular orbital (HOMO) level‐poly(3‐hexylthiophene) (P3HT) is mixed with materials with a deeper HOMO (PTB7, TQ1) to form binary blends of the type P3HTx:B1‐x (0 ≤ x ≤ 1) that is p‐type doped by F4TCNQ. For B = PTB7, a Seebeck coefficient S = 1100 µV K−1 with conductivity σ = 0.3 S m−1 at x = 0.10 is achieved, while for B = TQ1, S = 2000 µV K−1 and σ = 0.03 S m−1 at x = 0.05 is found. Kinetic Monte Carlo simulations with parameters based on experiments show good agreement with the experimental results, confirming the intended mechanism. The simulations are used to derive a design rule for parameter tuning. These results can become relevant for low‐power, low‐cost applications like (providing power to) autonomous sensors, in which a high Seebeck coefficient translates directly to a proportionally reduced number of legs in the thermogenerator, and hence in reduced fabrication cost and complexity. [ABSTRACT FROM AUTHOR]

Selective electron transport and extraction are essential to the operation of photovoltaic devices. Electron transport layer (ETL) is therefore critical to organic photovoltaics (OPV). Herein, an ETL configuration is presented comprising a solution‐processed n‐n organic heterojunction to enhance electron transport and hole blocking, and boost power conversion efficiency (PCE) in OPV. Specifically, the n‐n heterojunction is constructed by stacking a narrow‐band n‐type conjugated polymer layer (PNDIT‐F3N) and a wide‐band n‐type conjugated molecule layer (Phen‐NaDPO). Based on the ultraviolet photoelectron spectroscopy measurement and numerical simulation of current density‐voltage characteristics, the formation of the built‐in potential is investigated. In three OPVs with different active layers, substantial improvements are observed in performance following the introduction of this ETL configuration. The performance enhancement arises from the combination of selective carrier transport properties and reduced recombination. Another contributing factor is the good film‐forming quality of the new ETL configuration, where the surface energies of the related materials are well‐matched. The n‐n organic heterojunction represents a viable and promising ETL construction strategy for efficient OPV devices. [ABSTRACT FROM AUTHOR]

Organic electrochemical transistors (OECTs) have the potential to revolutionize the field of organic bioelectronics. To date, most of the reported OECTs include p‐type (semi‐)conducting polymers as the channel material, while n‐type OECTs are yet at an early stage of development, with the best performing electron‐transporting materials still suffering from low transconductance, low electron mobility, and slow response time. Here, the high electrical conductivity of multi‐walled carbon nanotubes (MWCNTs) and the large volumetric capacitance of the ladder‐type π‐conjugated redox polymer poly(benzimidazobenzophenanthroline) (BBL) are leveraged to develop n‐type OECTs with record‐high performance. It is demonstrated that the use of MWCNTs enhances the electron mobility by more than one order of magnitude, yielding fast transistor transient response (down to 15 ms) and high μC* (electron mobility × volumetric capacitance) of about 1 F cm−1 V−1 s−1. This enables the development of complementary inverters with a voltage gain of >16 and a large worst‐case noise margin at a supply voltage of <0.6 V, while consuming less than 1 µW of power. [ABSTRACT FROM AUTHOR]

Despite quick development of perovskite light‐emitting diodes (PeLEDs) during the past few years, the fundamental mechanisms on how ion migration affects device efficiency and stability remain unclear. Here, it is demonstrated that the dynamic redistribution of mobile ions in the emissive layer plays a key role in the performance of PeLEDs and can explain a range of abnormal behaviours commonly observed during the device measurement. The dynamic redistribution of mobile ions changes charge–carrier injection and leads to increased recombination current; at the same time, the ion redistribution also changes charge transport and results in decreased shunt resistance current. As a result, the PeLEDs show hysteresis in external quantum efficiencies (EQEs) and radiance, that is, higher EQEs and radiance during the reverse voltage scan than during the forward scan. In addition, the changes on charge injection and transport induced by the ion redistribution also well explain the rise of the EQE/radiance values under constant driving voltages. The argument is further rationalized by adding extra formamidinium iodide (FAI) into optimized PeLEDs based on FAPbI3, resulting in more significant hysteresis and shorter operational stability of the PeLEDs. [ABSTRACT FROM AUTHOR]

A novel patterning technique of conductive polymers produced by vapor phase polymerization is demonstrated. The method involves exposing an oxidant film to UV light which changes the local chemical environment of the oxidant and subsequently the polymerization kinetics. This procedure is used to control the conductivity in the conjugated polymer poly(3,4-ethylenedioxythiophene):tosylate by more than six orders of magnitude in addition to producing high-resolution patterns and optical gradients. The mechanism behind the modulation in the polymerization kinetics by UV light irradiation as well as the properties of the resulting polymer are investigated. [ABSTRACT FROM AUTHOR]

In electronics, the field-effect transistor (FET) is a crucial cornerstone and successful integration of this semiconductor device into circuit applications requires stable and ideal electrical characteristics over a wide range of temperatures and environments. Solution processing, using printing or coating techniques, has been explored to manufacture organic field-effect transistors (OFET) on flexible carriers, enabling radically novel electronics applications. Ideal electrical characteristics, in organic materials, are typically only found in single crystals. Tiresome growth and manipulation of these hamper practical production of flexible OFETs circuits. To date, neither devices nor any circuits, based on solution-processed OFETs, has exhibited an ideal set of characteristics similar or better than today's FET technology based on amorphous silicon. Here, bar-assisted meniscus shearing of dibenzo-tetrathiafulvalene to coat-process self-organized crystalline organic semiconducting domains with high reproducibility is reported. Including these coatings as the channel in OFETs, electric field and temperature-independent charge carrier mobility and no bias stress effects are observed. Furthermore, record-high gain in OFET inverters and exceptional operational stability in both air and water are measured. [ABSTRACT FROM AUTHOR]

The semiconductor-electrode interface impacts the function and the performance of (opto)electronic devices. For printed organic electronics the electrode surface is not atomically clean leading to weakly interacting interfaces. As a result, solution-processed organic ultrathin films on electrodes typically form islands due to dewetting. It has therefore been utterly difficult to achieve homogenous ultrathin conjugated polymer films. This has made the investigation of the correct energetics of the conjugated polymer-electrode interface impossible. Also, this has hampered the development of devices including ultrathin conjugated polymer layers. Here, Langmuir-Shäfer-manufactured homogenous mono- and multilayers of semiconducting polymers on metal electrodes are reported and the energy level bending using photoelectron spectroscopy is tracked. The amorphous films display an abrupt energy level bending that does not extend beyond the first monolayer. These findings provide new insights of the energetics of the polymer-electrode interface and opens up for new high-performing devices based on ultrathin semiconducting polymers. [ABSTRACT FROM AUTHOR]

The color of polymer solar cells using an opaque electrode is given by the reflected light, which depends on the composition and thickness of each layer of the device. Metal-oxide-based optical spacers are intensively studied in polymer solar cells aiming to optimize the light absorption. However, the low conductivity of materials such as ZnO and TiO2 limits the thickness of such optical spacers to tenths of nanometers. A novel synthesis route of cluster-free Al-doped ZnO (AZO) nanocrystals (NCs) is presented for solution processing of highly conductive layers without the need of temperature annealing, including thick optical spacers on top of polymer blends. The processing of 80 nm thick optical spacers based on AZO nanocrystal solutions on top of 200 nm thick polymer blend layer is demonstrated leading to improved photocurrent density of 17% compared to solar cells using standard active layers of 90 nm in combination with thin ZnO-based optical spacers. These AZO NCs also open new opportunities for the processing of high-efficiency color tuned solar cells. For the first time, it is shown that applying solution-processed thick optical spacer with polymer blends of different thicknesses can process solar cells of similar efficiency over 7% but of different colors. [ABSTRACT FROM AUTHOR]

Organic photovoltaics are under intense development and significant focus has been placed on tuning the donor ionization potential and acceptor electron affinity to optimize open circuit voltage. Here, it is shown that for a series of regioregular-poly(3-hexylthiophene):fullerene bulk heterojunction (BHJ) organic photovoltaic devices with pinned electrodes, integer charge transfer states present in the dark and created as a consequence of Fermi level equilibrium at BHJ have a profound effect on open circuit voltage. The integer charge transfer state formation causes vacuum level misalignment that yields a roughly constant effective donor ionization potential to acceptor electron affinity energy difference at the donor-acceptor interface, even though there is a large variation in electron affinity for the fullerene series. The large variation in open circuit voltage for the corresponding device series instead is found to be a consequence of trap-assisted recombination via integer charge transfer states. Based on the results, novel design rules for optimizing open circuit voltage and performance of organic bulk heterojunction solar cells are proposed. [ABSTRACT FROM AUTHOR]

Preparation of size-tunable ultrathin W18O49 nanowires by an alcohol-assisted solvothermal decomposition of tungstic acid is reported. The synthesis of ultrathin W18O49 nanowires can be achieved at large scale and low cost, while changing the molecular size of the used alcohols can control the nanowire morphology. With increasing the molecular size of the alcohol, the synthesized W18O49 nanowires have smaller diameters and longer lengths. The as-prepared blue W18O49 nanomaterials show a very strong visible light absorption caused by oxygen defects and an aspect ratio-dependent photocatalytic activity on the degradation of pollutant rhodamine B (RhB) under simulated solar light irradiation. It is found that the W18O49 nanowires with highest aspect ratio show the highest activity in the photodegradation of RhB, which could be related to their higher density of oxygen surface defects in combination with a higher adsorption capability of RhB. This new synthetic route of size tunable ultrathin W18O49 nanomaterials will enlarge their potential applications and can be possibly used in the pyrolyzing synthesis of other metal oxide nanomaterials. [ABSTRACT FROM AUTHOR]

Ferromagnetic metal-organic semiconductor (FM-OSC) hybrid interfaces have been shown to play an important role for spin injection in organic spintronics. Here, 11,11,12,12-tetracyanonaptho-2,6-quinodimethane (TNAP) is introduced as an interfacial layer in Co-OSCs heterojunctions with an aim to tune the spin injection. The Co/TNAP interface is investigated by use of X-ray and ultraviolet photoelectron spectroscopy (XPS/UPS), near edge X-ray absorption fine structure (NEXAFS) and X-ray magnetic circular dichroism (XMCD). Hybrid interface states (HIS) are observed at Co/TNAP interfaces, resulting from chemical interactions between Co and TNAP. The energy level alignment at the Co/TNAP/OSCs interface is also obtained, and a reduction of the hole injection barrier is demonstrated. XMCD results confirm sizeable spin polarization at the Co/TNAP hybrid interface. [ABSTRACT FROM AUTHOR]

The design of the earth‐abundant, nonprecious, efficient, and stable electrocatalysts for efficient hydrogen evolution reaction (HER) in alkaline media is a hot research topic in the field of renewable energies. A heterostructured system composed of MoSx deposited on NiO nanostructures (MoSx@NiO) as a robust catalyst for water splitting is proposed here. NiO nanosponges are applied as cocatalyst for MoS2 in alkaline media. Both NiO and MoS2@NiO composites are prepared by a hydrothermal method. The NiO nanostructures exhibit sponge‐like morphology and are completely covered by the sheet‐like MoS2. The NiO and MoS2 exhibit cubic and hexagonal phases, respectively. In the MoSx@NiO composite, the HER experiment in 1 m KOH electrolyte results in a low overpotential (406 mV) to produce 10 mA cm−2 current density. The Tafel slope for that case is 43 mV per decade, which is the lowest ever achieved for MoS2‐based electrocatalyst in alkaline media. The catalyst is highly stable for at least 13 h, with no decrease in the current density. This simple, cost‐effective, and environmentally friendly methodology can pave the way for exploitation of MoSx@NiO composite catalysts not only for water splitting, but also for other applications such as lithium ion batteries, and fuel cells. A heterostructured system composed of MoSx on NiO nanosponges is proposed as a robust catalyst for water splitting. The hydrogen evolution reaction in 1 m KOH electrolyte resulted in a low overpotential (406 mV) to produce a 10 mA cm−2 current density. The Tafel slope is 43 mV per decade, the lowest ever achieved for MoS2‐based electrocatalyst in alkaline media. [ABSTRACT FROM AUTHOR]