Search

The SnZn defect passivation and heterojunction interface energetics‐modification are crucial for further improvement of open‐circuit voltage (Voc) and efficiency of Cu2ZnSn(S,Se)4 (CZTSSe) solar cells. Herein, a simple but effective cation substitution strategy is reported to promote the performance of CZTSSe devices by simultaneously modifying the absorber and heterojunction interface. This is achieved by introducing the organic silicon salt C8H20O4Si into CZTSSe precursor solution as a source of silicon to partially substitute Sn with Si. Systematic studies reveal that there are two mechanisms synergistically contributing to the increase of efficiency: 1) This strategy can passivate the undesired SnZn defect in CZTSSe absorber more efficiently, leading to at least one order of magnitude lower SnZn defect density and beneficial carrier transport properties; 2) After Si incorporation, the conduction band minimum of the CZTSSe is upshifted, thus enlarging the bandgap, which ultimately optimizes the energy level structure at the CdS/CZTSSe interface and reduces interfacial energy loss by decreasing the carrier transport barrier. Consequently, the CZTSSe device with 7% Si substitution delivers a satisfactory efficiency of 13.02% owing to an increase in Voc. It is hoped the Si substitution strategy reported here can provide inspiration for developing advanced CZTSSe devices with broad application prospects. [ABSTRACT FROM AUTHOR]

Abundant intrinsic defects and defect clusters in Cu2ZnSn(S,Se)4 (CZTSSe) solar cells lead to severe nonradiative recombination and limited photoelectric performance. Therefore, developing effective method to suppress the detrimental defects is the key to achieve high‐efficiency solar cell. Herein, a convenient two‐step cooling strategy in selenization process is reported to suppress the CuZn and SnZn defects and defect clusters synergistically. The results show that rapid cooling during section from selenization temperature to turning temperature can inhibit the volatilization of Sn and restrain the corresponding Sn‐related defects, while slow cooling during the subsequent temperature section can reduce the degree of Cu‐Zn disorder. Benefitting from the synergistic effect of two‐step cooling, a significantly lowered concentration of SnZn and CuZn defect and their defect clusters [2CuZn+SnZn] in absorber is observed, meanwhile, a reduced band tailing effect and promoted carrier collection efficiency of the photovoltaic device is obtained. Finally, a device with improved open‐circuit voltage (Voc) of 505.5 mV and efficiency of 12.87% is achieved. This study demonstrates the impact of cooling process on defects controlling for the first time and provides a simple and effective new strategy for intrinsic defect control, which may be universal in other inorganic thin film solar cells. [ABSTRACT FROM AUTHOR]

The photovoltaic performance of the environmentally friendly Cu2ZnSn(S,Se)4 (CZTSSe) solar cells is lower than its predecessor Cu(In,Ga)Se2 solar cells. Severe carrier recombination at the CZTSSe/CdS interface is one major reason that results in a large open‐circuit voltage loss. Doping zinc into CdS is a feasible strategy to modifying the CdS buffer layer film, but the present methods are not satisfactory. In this study, novel zinc incorporation strategy is developed to deposit a gradient composition ternary ZnxCd1–xS buffer layer for optimizing the heterojunction interface. The application of gradient composition ZnxCd1–xS buffer layer constructs a gradient conduction band energy configuration in the CZTSSe/buffer layer interface, which highly reduces the interface recombination. The suppressed interface recombination contributes to the enhanced open circuit voltage and device performance. Consequently, the CZTSSe solar cell based on gradient composition ZnxCd1–xS buffer layers achieves champion efficiency of 12.35% with VOC of 504.81 mV, JSC of 36.90 mA cm−2, and FF of 66.28%. It is worth noting that flammable and the toxic hydrazine solvent are replaced by the safe and low‐toxic 2‐methoxyethanol, making it more promising for the future commercialization of CZTSSe solar cells. [ABSTRACT FROM AUTHOR]

Solution processing of Cu(In,Ga)Se2 (CIGS) absorber makes it cost‐competitive in the photovoltaic market. It is reported that copper‐poor ordered vacancy compound (OVC) is crucial for high performance CIGS solar cells. However, in solution process method, controllable formation of OVC is unavailable and limited research has been carried out. In this work, the controllable formation of the OVC phase on the CIGS surface is successful by controlling the selenization temperature and intentional variation of Cu/(In+Ga) stoichiometry in precursors for top layers and bulk layers deposition. The effects of OVC contents on the device performance are investigated. The CIGS thin film with OVC phase exhibits a lower valence band position. Meanwhile, the CIGS devices with optimized OVC content show decreased interface defects density and better carrier collection ability. The above advantages translate into a champion PCE of 16.39% for CIGS device with OVC phase, which is the champion performance among non‐hydrazine solution‐processed CIGS solar cells. The results demonstrate that the controllable formation of OVC phase approach should make a significant contribution to the efficiency promoting of solution processed CIGS solar cells. [ABSTRACT FROM AUTHOR]