Search

This study aimed to evaluate the preparation and characterization of paper towels from watermelon rind waste. The paper towel manufacturing process had several stages: the drying process, pulping process, bleaching process, and printing process. There were five treatments, including paper towels use of NaOH 2.5 M with pulp recycling, paper towels use of 1 NaOH with pulp recycling, paper towels use of 1 NaOH, paper towels use of 1 NaOH with additives, and paper towels use of 1 NaOH with different drying time (110 oC for 60 minutes with ten days of the natural drying). Several characterizations have been employed, such as physical and mechanical properties and optical and chemical properties. The treatments of paper towels were tested, and the test results were compared with SNI 7891: 2017. From the FTIR test, it was observed that the functional groups formed from paper towels from watermelon rind waste. From the Microscope test, paper towels from watermelon skin should be added with materials with long fibers. Based on Physical and Mechanical Characterization, paper towels comply with the SNI. Based on optical characterization, it complies with the SNI for treatments 4 and 5. Chemical characterization is higher than standard. It can be concluded that the natural paper towels from watermelon rind waste comply with the standard of SNI ISO 7891:2017 about Basic Paper towels within the parameter of grammage and water absorption capacity, Tensile strength except for the parameter of tensile strength, pH extract, and fluorescence. [ABSTRACT FROM AUTHOR]

Paper is now an integral feature of humanoid existence in a multitude of ways, and it is getting more and more popular. In ordinary life, a massive portion of paper is consumed. The difficulty of finding feedstock is becoming ever more acute as paper consumption rises. This ultimately led to the extraction of resources. Since the demand for paper has skyrocketed, recycling paper has become much more popular. The accumulation of vast quantities of waste paper in any big organization, notably institutions of higher education such as schools and universities, seems to be fairly prevalent. It's also worthwhile to make optimum use of recyclable materials (office files, craft papers, registers, etc.). A recyclable machine will help minimise energy consumption and paper waste. The valuable feature of salvaging would be that it lessens the environmental impact by a couple of percent. The design and fabrication of both humanly and remotely controlled paper recycling programmes are studied using previous literature. producing a lightweight, easily handled composting machinery that can be deployed to ease the process and reduce the cost of paper production. Then the effluents would be treated employing various natural filters due to paper recycling. Hibiscus, gooseberry, and vetiver are being used to treat the contaminated water. All of these constituents operate together to clear the water of surplus particles. Waste water treatment is indeed a process of preventing impurities from effluent and transferring them to an effluent that may be recycled into the water cycle. The process of turning waste water into fresh water that can be dispersed directly into the ecosystem. The effluent holds a variety of natural substances, which may also degrade the overall quality of the water. As nothing more than a corollary, water treatment principally helps to clear debris and other pathogens. The level of trash, which is routinely emitted into the ether, is reduced in terms of treatment of wastewater, boosting the atmosphere's health. In this study, both paper reutilization and waste water treatment studies are carried out using various literature. [ABSTRACT FROM AUTHOR]

Generally, development in the pulp and paper industry requires extensive cutting of trees, which in effect contributes to deforestation. The dramatic growth in demand for wood supply, combined with the increasingly increasing cost of timber, has created a surge of interest in the use of non-wood plant fibres for paper production in widely developed countries. The use of waste material in pulping and paper-based industries could be beneficial as it helps prevent the need for disposal, which currently increases agricultural costs and causes environmental deterioration due to pollution and fires. The manufacture of sugarcane bagasse paper may help to minimize deforestation in the development of paper utilizing wood, which also contributes to the creation of biodegradable, biocompatible, and eco-friendly paper utilizing non-wood fibre. This would help the industry to develop sustainable technology in the current economy and environmental order. In the meantime, the magnetic material inside the paper acts as a filler can improves the quality and strength of the paper. While the incorporation of paper radiation will also improve the quality of pulp production, by preventing the presence of fungi on paper. This will be widely used on food wrapping or packaging that is clean is the most important aspect that should be taken to prevent food from being damaged. Biodegradable implies that it can be spontaneously broken down by microorganisms such as bacteria, fungi under some circumstances such as temperature, humidity and others. [ABSTRACT FROM AUTHOR]

The primary purpose of this study is to assess the efficiency of biodigesters in the production of biogas through the application of anaerobic treatment to waste paper and canteen contents. Components and Methods of Research: The biodigester's waste, which included paper and garbage from the canteen, was collected for analysis on day 14. When determining the levels of biogas for both groups, a smart biogas metre was utilised. At a significance threshold of 0.05, a confidence interval of 95 percent, and a G-power of 80 percent, a total of 28 samples were determined, with 14 samples of each of the two groups being included in the analysis. According to the findings, the biodigester was given fourteen samples of waste materials throughout a span of fourteen days. These samples included garbage from canteens and paper, totaling fourteen samples. When compared to canteen waste, the biodigester produced 4.56 cubic metres of biogas from paper waste (10.20 m3). As a result of the investigation, paper waste produced a lower amount of biogas than canteen waste. As indicated by the p-value of 0.004 (p<0.05), the independent t-test samples demonstrate a statistically significant difference between the two groups. One other piece of evidence that demonstrates a statistically significant difference between the two sets of data is provided by this. A conclusion that can be drawn from this study is that the anaerobic treatment of canteen trash results in the production of more biogas than paper waste. [ABSTRACT FROM AUTHOR]

The major aim of this study is to compare the power generation of carbon felt electrode and carbon paper electrode operated Microbial fuel cells (MFC) using restaurant wastewater. Restaurant wastewater samples were collected from MFC with carbon felt electrode (N=13) and carbon paper electrode (N=13) operated for 10 days (G power 80%). Voltage was measured using a multimeter and current, power, power density was calculated from it for both groups. The Power generation was found to be high in MFC operated with carbon felt electrode (410 mW/m2) due to its active surface area, strong conductivity, and good biocompatibility compared to carbon paper electrode (121 mW/m2). The independent sample T-test was done which showed that the power generation of MFC operated with carbon felt electrode (p<0.001) found to be significantly higher compared with MFC operated with carbon paper electrode. The study shows that carbon felt electrode operated MFC is able to achieve higher power generation compared to carbon paper electrode. [ABSTRACT FROM AUTHOR]

The energy and exergy analysis of the Riau Andalan Pulp and Paper (RAPP) Pangkalan Kerinci are described in this article. This article's main goals are to study the system components independently and to locate and quantify the locations with the greatest energy and exergy losses. The analysis with the first law and second law of thermodynamics which are able to observe comprehensively the irreversibility of each component in the system is carried out due to the low efficiency of the steam power plant. The investigation is performed with the actual data obtained from the plant. From the evaluation results, the Pump II Component has the highest Exergetic Efficiency (95%), while the Feed Water Tank (FWT) component has the lowest Exergetic Efficiency (30.68%). The Boiler component has the largest exergy destruction value (454.2548 MW), while the Pump component has the smallest exergy destruction value (0.0006 MW). Next, the FWT component has the largest Exergy Destruction Ratio value (69.32%), while the Pump I component has the smallest Exergy Destruction Ratio (0.79%) at the steam power plant. In addition, the investigation of the ambient temperature effects on the performance of the plant was also carried out. From the results that have been investigated, the ambient temperature significantly affects the performance of each component. Some components are at their best performance when the ambient temperature reaches 23°C and the condenser has the lowest efficiency when the environmental pressure in the power plant reaches 1.5 bar (64.8%) [ABSTRACT FROM AUTHOR]

The demand for cement has grown due to the rapid growth of the building sector. Cement manufacture, on the other hand, produces more greenhouse gases and carbon dioxide. As a result, different construction materials must be sought. Paper pulp is made from waste from the paper industry. Every year, the paper industry consumed a significant amount of land in the surrounding area. Some wastes are thrown on land as a disposal method, while some businesses burn their industrial waste in incinerators, causing serious air pollution issues. The impact of employing paper pulp and crushed stone dust as partial replacements in concrete is discussed in this study. The advantages of using paper pulp with crushed stone are explored in this study. Furthermore, this research presents the findings of an experimental inquiry for M35 grade concrete employing wastepaper as an extra ingredient in concrete mixes for housing projects. [ABSTRACT FROM AUTHOR]

The application of insecticides on local product filter paper can be made in three ways: droplet use pipette, manual spray, and printing spray. Insecticides play an essential role in a paper, mainly used for testing susceptibility. The way the insecticide is applied affects the distribution on the paper surface. The purpose of calculating the distribution of insecticides on local filter paper is to determine the amount of insecticide in the cavity volume of ordinary paper. The research aims to get the data quality of impregnated paper local production with various spray techniques. To determine the volume of voids on paper and determine the distribution of insecticides can be using ImageJ software. The type of paper used is locally produced filter paper with insecticide lambda cyhalothrin with a predetermined concentration. The study results showed that with the spray machine method, the distribution of insecticides was more evenly distributed than the standard spray method. The range of paper cavity volumes with a spray machine is shorter than the volume range of paper cavities sprayed manually (0.005113), while those with ordinary sprays are (0.007349). These differences indicate that the spray machine is better than the manual spray method. [ABSTRACT FROM AUTHOR]

This study is about the characterization of pulp and paper from sago fiber waste. The process has several stages: preparing a solution, sago fiber analysis, pulping process, and printing process. The required solutions are NaOH solution (technical), 10% BaCl2 solution, 0.1 N HCl solution, 60% ethanol solution, phenolphthalein indicator solution, 1% starch indicator solution, sindur methyl indicator solution of NaOH titration, borax solution, Na₂S solution (technical), and THIO solution (1 N; 0.1 N). The pulping process is carried out by inserting sago fiber and solutions into a rotary digester machine for 4 hours (170oC). Then, it is removed after 24 hours and dried by a spinner machine. Characterizations on the sample include: chemical and physical properties, mechanical properties, and optical properties. The result shows that sago fiber waste can be used as raw material for paper. The value of grammage of 62 g/m2, thickness of 0.1294 mm, water absorption capacity of 627.27 g/m2, water content of 9.83%, ash content of 26.26%, pH of 7.9, tensile strength of 14.22 MD and 13.33 CD, brightness of 19.8%, and opacity 22.78. The pore diameter of the paper is 4.608 nm. [ABSTRACT FROM AUTHOR]

An innovation in paper technology that is totally different from the papermaking technology that has been known now, has been found in the 21st century in China. This new discovery paper does not use cellulose fibers as its raw material, and does not use water at all in its production process. Because it is made of inorganic mineral coming from calcite rocks, this paper is called 'rock paper' or stone paper. The process of stone papermaking in principle mixes fine powder of calcite rock with non-toxic resin, one of which is HDPE (high density polyethylene), as well as other additives, then melted at high temperatures and formed into a sheets like paper. The properties of stone paper are very similar and even have advantages compared to conventional paper. This type of paper is claimed to be more environmentally friendly than conventional paper because it does not use plant fibers as raw material, which means there is no trees cut. It can be recycled and produces low greenhouse gas emissions. [ABSTRACT FROM AUTHOR]

Wood is biomass made from lignocellulose, the main raw material for pulp production, both species of hardwood and softwood. Utilization of as much wood as possible, including less-known wood species, is widely open because the availability of good quality wood for industry raw materials is increasingly limited. In general, all wood species can be used for paper pulp. But the selection of types of lignocellulosic material with specific properties, such as physical, anatomical and chemical, play an important role in efficiently using wood as raw materials for pulp and paper. This research was carried out to examine wood properties (specific gravity, fiber quality and cellulose content) of four less-known hardwoods from natural tropical rainforest in South Sulawesi province of Indonesia and assessed their potential use for paper pulp. Those hardwood species comprised of cempedak (Artocarpus integer Merr.), jabon merah (Anthocephalus macrophyllus Hav.), saling-saling (Artocarpus teysmanii Miq.) and simpur (Dillenia serrata Thunb.). The specific gravity determined by the weight of oven dried wood and volume of air dried wood where the wood volume be measured by water immersion method, the fiber dimensions measured through maceration preparations which was made using the Franklin procedure, while TAPPI method used for chemical analysis. In condition to paper pulp raw material, the specific gravity (0.40 – 0.69) is categorized as moderate, the fiber quality is classified as good (class II), and cellulose content (40.12% - 52.47%) is categorized as moderate to high for all those less-known hardwoods. All four less-known hardwoods studied potentially use for paper pulp raw materials. But simpur has the most potential due to long fiber and higher specific gravity. [ABSTRACT FROM AUTHOR]

This paper presents the results obtained from the analyses performed on seaweed and paper made with algal biomass addition using different analytical techniques, such as scanning electron microscopy with energy dispersive X-ray analysis (SEM-EDX) and the ion beam analysis (IBA) techniques Particle-induced X-ray emission (PIXE) and gamma-ray emission (PIGE). The analyzed samples consisted of seaweed from the Ulva rigida C. Agardh 1823 species collected from the Black Sea coast, Romania, and filter papers with different mass addition (0.5, 1, 2, 4 and 8%) of seaweed. Seaweed introduced into the paper can dislodge some of the cellulose fibers, helping to reduce the amount of stranded seaweed that is currently not valorized in Romania. From the analysis of the results, it results that no potential toxic elements have been identified in the algae structure and the algal biomass could be used in the filter paper manufacture. [ABSTRACT FROM AUTHOR]

In current work, the paper mill effluent is treated with electro-coagulation used as a iron and aluminum as sacrificial materials. Various operating parameters such as pH, treatment time and applied voltage were assorted and their influence on efficiency of electro-coagulation was studied. From the experimental investigation it has been found out that at optimum operating conditions like pH 7, treatment time 60 min and applied voltage 20V, COD and Turbidity removal efficiency were highest. [ABSTRACT FROM AUTHOR]

This work relates to the development of recycled paper from waste paper with the objective of optimization of the composition. The paper properties are much affected with composition like amount of waste paper, fresh paper, cotton shreds, adhesives and water. Samples were made by taking different composites and tests were performed to evaluate properties i.e. thickness, coefficient of friction, moisture content, scott bond strength, tensile strength. The testing concluded that the samples which were having cotton shreds and adhesives showed very good results closer to the fresh paper. [ABSTRACT FROM AUTHOR]

A significant demand has been placed on the building material industry, especially in the last decade due to the increasing population, which causes a chronic shortage of building materials. The current study aims at utilizing waste paper to produce papercrete bricks and study their engineering properties, a step towards sustainable development. Papercrete is rapidly gaining popularity in the building construction industry worldwide because of its environmental friendliness, low-cost and lightweight. The study considered literature and related ideas up to conceptualization and design of the trial ratio used in testing. Trial mixes of paper sludge, sand, and cement at different proportions made papercrete bricks of dimensions 220×110×102 mm. The tests conducted included compressive strength and water absorption. The mixes of paper sludge, sand, and cement in the ratio of 50, 35, and 15%, respectively, gave the best results. The compressive strength increased with the increase in the curing period. The rate at which the papercrete bricks absorbed water reduced as the curing period increased for all the papercrete trial mixes. It was concluded that percentages of paper sludge less than 50% are recommended for non-load bearing walls such as parapet walls and partition walls. [ABSTRACT FROM AUTHOR]

Variation of fly ash and pulp paper composition at 110°C for 6 hours was carried out to discern the effect of fly ash and pulp paper addition in papercrete. sixth variations in paper pulp and fly ash composition were employed to perceive the characteristic that occurs in the sample. The papercrete material composition was weighed, mixed until it became homogeneous and then casted in a mold with a size of 18 x 5 x 2 cm3. Papercrete samples were allowed to stand within the mold at room temperature for 24 hours and released from the mold to stand again for the next 24 hours, after which it heated at 110°C for 6 hours. Characterization using XRF, SEM-EDX as well as Mechanical and physical tests carried out after the samples was cold. Papercrete with sample code K6 has the highest flexural strength and density value of 2.03 MPa and 2.4 gr/cm3 while papercrete with sample code K1 has the lowest flexural strength and porosity value of 0.4 MPa and 17.89%. Characterization shows that the chemical composition of the samples was dominated by the oxide compound CaO and SiO2 in papercrete. [ABSTRACT FROM AUTHOR]

The article examines the structure of silk fibers and ways of efficient use of fiber waste. Based on the analysis of the composition and structure of the fibers, it is possible to use them for paper production. The use of short staple fibers in the production of stock paper and the processes of preparing them for incorporation into paper pulp are widely covered. Information is provided on the technological process of cleaning fibers before adding them to paper pulp. The influence of the mass fraction of fibers in paper on its strength, breaking and tearing has been thoroughly analyzed and illustrated by means of graphs. For the production of high-quality paper, for example, valuable paper, for the preparation of paper used in printing, drawing, painting, etc. Fiber semi-finished products must be cut to the required length and separated into individual fibrils before crushing (grinding). The technology of preparation of natural silk waste as raw material for paper production is presented. In addition to silk fiber cotton fiber was also studied in the research work. Theoretically, the effect of fibers in tearing and breaking of paper is shown in the pictures. The use of fibers in the production of anti-counterfeiting paper and the process of adding them to the pulp are given. [ABSTRACT FROM AUTHOR]

The target of this idea is to plan the paper cutting machine utilizing Geneva component. This machine is utilized to decrease the manual work of paper cutting, and furthermore efficient. This machine is exceptionally valuable for paper fabricating industry likewise we can keep away from the human blunders and it can be used in schools, collages stationary shops, paper stores, etc. This project is designed by chain drive, Geneva mechanism, paper cutter, hinge joint and spring. This machine will minimize the errors occurred while cutting papers using hands and it will also reduce the risk of paper cutting.Thisventures is fixated on the plan and manufacture of an Automatic paper cutting machine utilizing some privately discovered materials. Paper is one of the significantly utilized material in our everyday exercises in bringing data's down essential data's, it is vital that there is a machine that can deal with it at a homegrown level to give the ideal structure for different use.The machine is tried and the yield is assessed. [ABSTRACT FROM AUTHOR]

There is a shortage of paper and paper products in Uzbekistan. In this regard, this work presents the results of studies of the possibility of obtaining paper from cotton cellulose and using cotton cellulose in combination with waste paper. Were studied methods of making prototypes of paper from cotton cellulose obtained from different varieties of cotton linti, as well as from a mixture of this cellulose in combination with waste paper at different ratios. [ABSTRACT FROM AUTHOR]

Super teak is a fast grown species of teak (Tectona grandis Linn. f) derived from several clones. This has facilitated plantation rotations as short as 5 years. The main target of conventional plantation teak was initially for high value logs. Young teak wood from plantation forest usually has a small diameter. Moreover, the wood from very young stems is unsuitable for direct utilization, but advance wood processing technology can improve the wood properties of small diameter logs. This study aimed to assess the potential utilization of young super teak for high quality products namely furniture, flooring, and veneer, and assess the possibility of the use of manufacture waste for pulp paper and wood pellets as side products. The evaluation were carried out according to the National Indonesian Standard and other international standard requirements. 18 logs from wet (Bogor) and dry (Magetan) sites representing large, medium, and small diameter classes were collected. According to SNI 01-0608-1989 Timber for Furniture, 5-year-old super teak was suitable for furniture production. Furthermore, according to SNI 7732.1: 2011: Teak Veneer, the super teak was classified as Grade C because of the presence of sapwood, pinholes, tight and lose knots. According to Australian Timber Flooring Association, 5-year-old super teak was classifiesd as soft flooring group, the same group as mature teak & radiata pine. The young super teak was classified as Class Quality/Group II with very low active alkali consumption and low Kappa Number according to Indonesian wood fibre criteria for pulp and paper materials and Association of Pulp and Paper in Brazil. Finally, based on SNI 802: 2014 Wood Pellet, the super teak was recommended as by-products for utilising the wood waste. [ABSTRACT FROM AUTHOR]

Briquettes produced from scrap paper are known for their low calorific value. The calorific value of briquettes from waste paper is in the fourth rank after waste wood, charcoal, and sawdust. Therefore, the correct ratio of composition mixture to create a higher calorific value is required. Spent Coffee Ground (SCG) has been selected as an added material in the composition of biomass mixture since SCG has a high calorific value and is easily found. The purpose of the study is to find the correct ratio that may increase the calorific value of the bio-briquettes made of scrap paper, based on comparative testing and analysis. There are four composition mixture samples used in the study. The first composition mixture is 90% of scrap paper and 10% adhesive; the second one is 70% of scrap paper, 20% of SCG, and 10% adhesive; the third composition mixture is 50% of scrap paper, 40% of SCG, 10% of adhesive; and the fourth composition mixture includes 30% of scrap paper, 60% of SCG and 10% of adhesive. The study shows that the greater ratio of SCG used in the composition will result in a higher calorific value. The research concludes that briquettes achieve their best performances in the composition mixture of 40% of SCG. In the proposed ratio, briquettes are not brittle and produce 5.366 kcal/kg of calorific value; 6.58% of water content; 5.37% of ash content; 28.28% of volatile matter; and 8.91% of shatter index. Therefore, the studied composition can be considered to produce the most efficient biomass briquettes made from scrap paper [ABSTRACT FROM AUTHOR]

This study explores the possibility of removing residual optical brighteners in paper, caused by the migration of OBAs from commercially available papers through water during an instance of water damage. From the standpoint of conservation treatment, this OBA removal experiment was conducted in the hope of providing a treatment method for the removal of OBAs as a reference point for the conservation community. This study presents an example case of removing offset OBAs, and the results of the removal experiment are discussed in order to explore the feasibility of the proposed treatment method. The results demonstrated that the removal of offset OBAs using a compatible conservation treatment is feasible. A combination of daylight bleaching with alkaline water and aqueous hydrogen peroxide solution is recommended, and the time of exposure to sunlight should be shortened as much as possible if performed on a bright, sunny day. However, performing such treatment on the actual cultural artefact will require careful assessment with regards to necessity and safety. [ABSTRACT FROM AUTHOR]

The global production of paper is on the rise, thus leading to increasing amounts of waste in different stages of paper manufacture. Paper sludge waste is the most abundant and there is a big potential to reuse it after appropriate processing. This research paper analyses paper sludge waste fired at 900°C temperature for 2 h in terms of mineral composition, particle density and water demand in cement-based mixtures, as well as the effect of paper sludge waste on the density, ultrasonic pulse velocity, compressive strength and mineral composition of cement-based specimens. In the cement paste mixtures 0%, 2.5%, 5%, 7.5% and 10% of cement was replaced with paper sludge waste fired at 900°C temperature for 2 h. The ratio between water and solid substances was 0.35. Gehlenite and calcium oxide were found to prevail in the mineral composition of paper sludge waste, whereas water demand of cement-based mixture incorporating paper sludge waste increased 30%. The intensity of XRD curves revealed that a higher content (more than 7.5%) of paper sludge waste fired at 900°C temperature for 2 h in the mix increases the amount of portlandite and reduces the amounts of cement minerals: alite and belite. An empirical equation was drawn on the grounds of statistical analysis to calculate the compressive strength according paper sludge waste content fired at 900°C temperature for 2 h. The correlation and determination factors more than 0.9 demonstrate that the change of compressive strength in relation to paper sludge waste content can be described by the second degree polynomial equation and the optimum content of paper sludge waste fired at 900°C temperature for 2 h in the cement matrix is 5%. The highest density and ultrasonic pulse velocity values of cement stone specimens after 28 days of curing were obtained of specimens containing 5% paper sludge waste. [ABSTRACT FROM AUTHOR]

The recycling of waste paper conserves our natural resources and will retrieve environmental quality. Concentrate on recycling waste paper into the usable board will benefit plants and the environment. This research depends on the investigation of manufacturing of usable board from waste paper. This manufacturing board can use instead of the board which manufactures from ordinary wood. On the other hand, it protected the forest and eliminates waste that harms the environment. This research illustrates the efficiency of our manufacturing board material by using mechanical tests and comparing it with a board manufactured by two types of ordinary wood and Medium-density fiberboard (MDF). Also, comparing the heat isolation between them. In this project, we use three types of waste paper: white, yellow envelope and newspaper. This waste paper produced our new board material. Our samples were manufactured with dimensions of 10*10 cm and 2 cm thickness. Different amount of waste paper and white glue was investigated to produce a batter board. Our study for the manufactured board materials demonstrated that a white paper sample was the battery on hardness and tensile test. However, yellow envelope samples were more efficient in the impact test than other samples. Moreover, yellow envelope samples were the better one between our samples in heat isolation. Mainly, the waste of paper and white glue was the cheapest to manufacture boards than using ordinary wood. [ABSTRACT FROM AUTHOR]

It is essential to use enzymes as a substituting chemical to enhance the properties of pulp and paper. However, there is a limited match between the material and the enzymes applied. Therefore, this research aims to increase pulp and paper properties enzymatically by adding papaya latex bio-activator in the recycled pulp process using the hydrolyzing method. The results showed that this bio-activator made the fiber bulky due to the storage of more water in the pulp, thereby expanding the fiber surface, which facilitated tearing and increasing fibrillation in the refining process. This process led to changes in the surface morphology of fiber and structure of pulp fibers, which were determined from the Scanning Electron Microscopy (SEM) test. It also increased fiber fibrillation, which led to a rise in bond strength between fibers capable of raising paper properties. In conclusion, papaya latex bio-activator reduces the use of chemical hydrogen peroxide (H2O2), increases fibrillation in the refining process and reduces environmental liquid waste pollution. [ABSTRACT FROM AUTHOR]

Quality and productivity are the things that are most often the focus of discussion in the production process. PT. Papertech Indonesia is one of the companies producing cardboard products or paper board industry (hard paper). The products produced in addition to core paper also produce other types of paper including: Chip Board, Super Chip Board, Cone Board, Core B. In producing paper, the thing that most affects the quality of a product is the change grade or the change in the type of product. If at the time of change grade there is an error in the settings it will cause problems, namely sheet break or broken paper. Sheet Break is broken paper which can cause a decrease in machine productivity and add defective products in the warehouse, this defect product is meant to not meet the specifications of the consumer. Six Sigma approaches and Failure Mode Effect Analysis (FMEA) used in this study to determine the sigma level value for sheet breaks, factors that cause sheet breaks and find solutions to reduce risk. The results showed that there are two machines that often experience Sheet Break, namely Couch Roll & Lumbreaker and Dryer 1st Group machines which are caused by various factors. Based on the value of the Risk Priority Number which is the largest for the cause of Sheet Break, namely unstable vacuum during Change Grade, Lack of understanding and skills in the Change Grade state, Lack of understanding of the steps for Change Grade. Based on these results, recommendations are given to minimize the causes of priority Sheet Breaks carried out for each category and each cause, one of the recommendations given is the use of appropriate vacuum equipment, conducting regular monitoring, training employees and implementing Kaizen. With these recommendations, PT. Indonesian papertech can use these recommendations as a form of improvement in order to minimize the occurrence of sheet breaks. [ABSTRACT FROM AUTHOR]

Effect of a natural compound extracted from Piper Betel leaf by determining bactericidal and or bacteriostatic effect to check antimicrobial efficacy on the pathogenic microorganisms. Bioactive compound extracted in different solvents i.e distilled water, ethanol, and methanol, and its effectivity was determined by measuring the zone of clearance (1 group and 96 samples per group by keeping threshold 0.05 and G power 80%, coincidence interval 95%, and enrollment ratio as 1) by agar diffusion method using kanamycin (30) as a control for the different time period (24 Hrs, 48Hrs and 72Hrs) at 37°C. Promising results were found for the zone of clearance in Escherichia.coli with a significance of about P<0.001 in the ethanol extract after 72 hours of incubation. Compared to 10% extract application where growth of S.aureus was reduced to 4%, addition of 100% crude inhibits bacterial growth up to 95% approximately. For S.aureus and E.coli though ethanol extract was found effective however no significant effect was observed for inhibiting Pseudomonas. Novel bioactive compound extracted from Piper Betel leaf was found effective against pathogens and can be used as a natural component with antimicrobial efficacy in the field of medicine. [ABSTRACT FROM AUTHOR]

The paper soap is an innovation in making soap. The form of paper soap is unique like thin sheets paper. The addition of natural compounds such as virgin coconut oil (VCO) and whey kefir in soap making could improve the quality of paper soap as herbal product. This research aims to determine the optimum formulation of herbal paper soap in three whey kefir mass composition 8%, 18% and 23%. The paper soap makes using a hot process with additional glycerin as a plasticizer. The characterization of herbal paper soap is using parameters tested of pH value, stability of foam, unsaponified fat, organoleptic test, and water content. The characteristic of paper soap has a thickness of 1 mm, smells good, and slightly yellowish. The best herbal paper soap is obtained for a composition of 8% with water content, unsaponified fat, pH, and foam stability 28%, 0.39%, 8 and 83% respectively. Therefore, the herbal paper soap with whey kefir of 8% has complied SNI no. 3532-2016 standard. [ABSTRACT FROM AUTHOR]

Karnaphuli Paper Mill (KPM) is the country's largest and state-owned paper mill, located at Chandraghona, Chattogram, alongside the Karnaphuli River. At present, 10 to 12 tonnes of paper are being produced daily, resulting in approximately 1000 to 1200 tonnes of waste effluents every day. The water of the Karnaphuli River is being polluting due to untreated effluents discharged from KPM outlets, posing a threat to the Karnaphuli River's aquatic lives. Thus, this research is carried out to test the raw effluents of KPM and the Karnaphuli River water, to compare the water quality with the World Health Organization (WHO) and Bangladesh Environmental Conservative Rules (BECR, 1997) standards to find out the effects of this water on aquatic lives and to suggest remedial measures. Raw effluents were collected from three points of outlets of KPM, and the river water were collected from ten points at upstream and ten points at downstream of outlet at an interval of 100 m each to test the water quality parameters, such as, pH, BOD, COD, total dissolved solids (TDS), Alkalinity, Hardness, Chloride, Turbidity, Fecal coliform, Al, Sn, and Co. The test results were found to be satisfactory, except a few parameters at few locations, which might have negative impacts on river water and aquatic lives. To mitigate the unacceptable concentrations, it is suggested to set up an effluent treatment plant (ETP) to treat the KPM effluents before discharging into the Karnaphuli River. [ABSTRACT FROM AUTHOR]

Cellulase enzymes in the refining process in paper making are known to reduce energy and grinding costs. The industry requires large amounts of cellulases related to the low activity of cellulases produced. The optimization process is known to increase the value of cellulase activity produced. In the process of cellulase production, carbon sources based on cellulose waste, such as grass and bagasse, can reduce production costs. The purpose of this study is to find out the optimum fermentation carbon source that produces the highest cellulase activity between grass and bagasse by actinomycetes ID07–287. It also aims to increase the value of cellulase activity by optimizing the concentration of selected carbon sources and the pH of the fermentation media. This research includes the preparation of grass biomass and bagasse, the production of cellulase enzymes for the selection of the optimum carbon source, and the optimization of the production of carbon source concentrations and the pH of the fermentation media. Based on the research results, it is known that grass is the best fermentation carbon source, with an activity value of 0.086 U/mL. The results of optimization of production, at a concentration of 2%, is the optimum concentration with an activity value of 0.099 U / mL and the pH of the fermentation media 9 produces an optimum activity value of 0.107 U/mL. [ABSTRACT FROM AUTHOR]

The pulp and paper making industry is looking for new main raw material based on its physical, chemical and morphological characteristics. Currently in this industry, bagasse is the most useful raw material in pulp and paper industry. The objective of this study is to determine its suitability for pulping. Acacia auriculiformis is a fast-growing tree normally found in Indonesia and Australia. Acacia auriculiformis leaf contains of cellulose, hemi-cellulose and lignin. The range of lignin content in Acacia auriculiformis is 19%-20%. The hemi-cellulose and lignin contents was removed by soda-pulping process using different concentrations as followed; 3%, 5%, 10%, 15% and 20%. In order to determine the optimum pulping conditions for Acacia auriculiformis craft paper, several tests were conducted such as apparent density, tear test, tensile strength test and moisture absorption. It was found that the Acacia auriculiformis fibre treated with 3% sodium hydroxide (NaOH) solutions gave good tear test of the paper. For apparent density test, the best concentration of NaOH used for treating Acacia auriculiformis pulping is at 15%. From the study, the optimum concentration of NaOH in treating Acacia auriculiformis fibre is at 5% for best result in tensile strength. Hence, from the overall tests, 5% concentration of NaOH is the optimum value. From the findings, Acacia auriculiformis fibre has a potential to be used in paper making and food packaging industry. [ABSTRACT FROM AUTHOR]

Paper-based food packaging serves to maintain product quality for a longer period. The addition of nanocellulose as a coating agent on paper can improve the quality of the recycled paper. Modification of nanocellulose with Al3+ can occur due to the interaction between Al3+ ions and the electrostatic negative surface charge of nanocellulose which can degrade microbial cells. Modification of nanocellulose was carried out by soaking it in AlCl3 solution then homogenized by an ultrasonic wave which was used for defibrillation of nanocellulose and encourage crosslinking of nanocellulose and Al3+ ions. The paper coating technique uses a deep coating by immersing the paper in modified nanocellulose suspension. The variations of AlCl3 concentration used were 0.01, 0.05, 0.1, and 0.15 N as much as 25 ml on 1 g dry base nanocellulose. The concentrations of nanocellulose used were 0.5, 1, 1.5, and 2 g in 25 ml of Al3+ solution. The results of paper water absorption and WVTR test showed that modified nanocellulose can reduce the absorption of water vapor and water absorption from the paper, so it has water resistance. Nanocellulose coated can increase the hydrophobicity of the paper based on contact angle test. Antimicrobial test on coating paper also showed antimicrobial activity on E.coli test bacteria and not on S. aureus bacteria. [ABSTRACT FROM AUTHOR]

This study aims to analyze Indonesia's strategy in facing the Voluntary Partnership Agreement on Forest Law Enforcement Governance and Trade (FLEGT-VPA) cooperation agreement between the European Union and Indonesia to improve the export performance of Indonesian wood products to the European Union market. With research, an analysis of the opportunities and challenges that Indonesia intends to face in maintaining the stability of the export activities of Indonesian wood products and improving the quality of these wood products so that they can be accepted based on the standards of the destination country. FLEGT-VPA is a bilateral agreement between the European Union and timber exporting nations to improve forest sector governance and ensure that timber and wood products supplied into the EU are produced in line with partner country laws and regulations. The issue that a developing country like Indonesia wants to experience in an effort to improve the quality of wood products according to the standards of the destination country is a large number of illegal logging, illegal timber sales and others. This study focuses on the pulp and paper industry and uses qualitative analysis research methods and analyzes the data collection techniques from various sources. The increase in the export performance of Indonesian pulp, paper and, paperboard to the European Union from 2016 after the ratification of the FLEGT-VPA shows that the quality of Indonesian products is promising to spread in the European Union market. [ABSTRACT FROM AUTHOR]

The purpose of this study was to investigate the efficacy of Sikacrete and Novel Hypo Sludge in improving the mechanical qualities of concrete. Investigate the impact that a number of environmental elements, including cycles of freezing and thawing, chemical agents, and high temperatures, have on the durability of concrete when it is coupled with Novel Hypo Sludge and Sikacrete. The Methods and the Materials: The new hypo sludge (paper pulp) concrete, which is produced by partially replacing cement with sikacrete and is compared to the standard M25 grade concrete, has a higher compressive strength than the standard concrete. Results: During this experimental examination, the impact of adding hypo sludge in the typical range of 30 percent on the stability properties of concrete was investigated. This was accomplished by analysing the compressive strength of grade M25 concrete after 28 days, using a cube dimension of 150mm×150mm×150mm. The results of the studies indicate that concrete with Novel Hypo Sludge performs significantly better than concrete that merely contains cement. Regular concrete had an average compressive strength of 26.09 N/mm2, but concrete that contained thirty percent Novel Hypo Sludge had a compressive strength of 32.92 N/mm2. According to the statistical analysis, the accuracy rate of comparing Novel Hypo sludge and Conventional concrete is considered statistically significant. The p value for this comparison is 0.000 (p<0.05), and it is two-tailed. In conclusion, the incorporation of Novel Hypo Sludge, which is composed of paper pulp, into Cement and SikaCrete results in a significant improvement in the compressive strength test performance of HSC. [ABSTRACT FROM AUTHOR]

The main problem that the society is facing now-a-days is the tedious process which are involved in disposal and handling the huge quantities of food and paper waste generated in India. The waste is discarded or fired, in roads which cause air pollution, a harmful gas, land pollution, smoke, particulates and residue may enter in to a water resource. Since these pollute the environment, these wastes are utilized efficiently and converted in to a useful product which must be eco-friendly. This current research is to produce lactic acid (LA) using various type of wastes such as food and paper sludge. Since LA can be synthesized only by two methods; one is chemical synthesis where natural sources such as petroleum, coal and natural gas are mainly used as a substrate. Another one is microbial synthesis in which carbohydrates such as sugar or starch is converted in to an alcohol or an acid. Most probably, both bacterial and fungal species are used and about 70-80% uses fermentation for the manufacture of Lactic acid. The mixed culture medium of lactobacillus delbrueckii and streptococcus. Sp strain shows highly efficient utilization of substrate. Since Solid state fermentation (SSF) has a possible technology for the synthesis of products related to microbial. This process has minimum energy needs, generates less waste and is eco-friendly. Various parameters such as substrate concentration, temperature likewise other parameters which influence the yield will be varied. The product obtained will be estimated further using HPLC. Overall, the result indicates that bio-waste might be an appropriate substrate for the synthesis of lactic acid. [ABSTRACT FROM AUTHOR]

The "Trim loss issue" (TLP) perhaps uttermost intriguing issues with regards to structure of advancement research It targets to determine the best cutting example of several things of varying lengths from a load of regular size measurable to meet the clients' wants while reducing waste due to trim misfortune. The subsequent numerical pattern is exceptionally nonconvex in nature went with a few imperatives with additional limitations of paired factors. This evades the utilization of straight advancement techniques. In this review work we utilize synergetic differential advancement (SDE) for the arrangement of this sort of issues. Four theoretical yet significant instances of trim misfortune issue emerging are used in the paper industry the test. The exploratory outcomes contrasted and those of different procedures show the capability of the SDE to take care of the issue. This paper includes introduction which explains a complete terminologies related to cutting stock problem, in literature review section we discuss various mathematical model which already exist in literature, in next section we discuss about mathematical formulation to reduce wastage. [ABSTRACT FROM AUTHOR]

This study aims, through experimental works, to develop a new and sustainable binder by reusing two waste materials, namely waste paper slag ash (WPSA) and granite dust (GD) to stabilize fine-grained soil and reduce the environmental impacts resulting from improper disposal in addition to reducing the use of cement and lime in soil stabilization. The soil utilized in this research was obtained from a site near 80th Street in Babylon Provence. The experimental works included sieve and hydrometer analysis, consistency limits, compaction test, and unconfined compression strength test at 3, 7, and 28 days of curing. Various binary blended binders derived from mixing of WPSA and GD at different proportions; 10:0, 7.5:2.5, 5:5, 2.5:7.5, and 0:10 were utilized. These binary blended binders were mixed with the virgin soil at 10% in the samples testing procedure. The results showed that the use of the mixture containing GD alone resulted in a reduction in the LL, PL, and PI, and when increase the percentage of WPSA in the mixture, LL and PL were increased while PI decreased. Moreover, the maximum dry density of the treated soil increased with the use of GD, however, it decreased significantly after the employing WPSA in the binder used. As per the outcomes of the compressive strength test, it was shown that the use of the mixture WPG0 that contains (100% WPSA) gave the highest compressive strength, which is equivalent to 14 times of that for the virgin soil after 28 days of curing. The strength then dropped with increasing the percentage of granite dust in the mixture. However, mixtures contained both of WPSA and GD exhibited acceptable compressive strength throughout the time of curing as the results indicated. [ABSTRACT FROM AUTHOR]

The understudies of schools and universities devour many papers as note pads, books, assessments, answer books and so forth. After utilizing these papers and advancing in the new class, new requests for scratchpad and books were delivered. The new paper creation by paper factories cause the cut of more trees and timberlands and become the explanation of water, air contamination. Reusing paper squander paper is probably ideal for the supportable turn of events and zero waste targets. Since squander paper reusing supplies critical commitments to the supportability of ranger service assets, to energy-saving endeavours, to decrease ecological contamination levels and viable usage of crude materials. The financial commitment of waste paper reusing can be a lot more prominent if these squanders are gathered at the source. It is essential to distinguish the areas that devour generally higher measure of paper; thus, raise their mindfulness, and give answers for on-source-partition rehearses in such areas. Generally, it realizes that the understudies of universities/schools burnthrough bigger measures of paper contrasted with other shopper units. The current investigation plans to ascertain the worth of financial advantage made by squandering papers gathered usingthe students of College/school. [ABSTRACT FROM AUTHOR]

Open graded friction course (OGFC) mixtures are generally utilised as an overlay layer on existing pavement layers at thicknesses of up to 50 mm. They are designed with open aggregate skeletons to mitigate noise impact, reduce spray and splash, and minimise night glare. They have also gained widespread popularity worldwide as a result of features such as slip resistance, water permeability, and urban heat reduction. However, despite these advantages, their design structure is somewhat weak due to the high proportion of large gradient gravel content with a lack of smaller particle gradations. In addition to creating air voids of up to 22%, these can cause bitumen and filler to drain down, which is considered one of the main problems of such mixtures. Several researchers have thus attempted to modify the properties of such mixtures by using additives to strengthen the asphalt bond, with improvement sought by adding polymer materials, fiber, or similar additives as additional soft materials. In this study, waste paper fiber (W-PF) was added after being picked to a small size, as this additive has not been used in previous research, in this area and offers both environmental and economic advantages. This was added to the binder at percentages of 0.3%, 0.5% and 0.7% by weight, and the performance of each mix was checked with respect to volumetric properties (air voids, bulk density, porosity and permeability) and mechanical properties (Cantabro wear loss (CL), skid resistance and indirect tensile strength (ITS)). The results show that incorporating W-PF into the asphalt binder generally improves the mixture's performance. With respect to volumetric scales, it leads to higher values of porosity, air voids, and permeability, with improvements of around 14%, 10%, and 31%, respectively, at 0.7% W-PF by weight of binder. As the paper dose increases, the bulk density decreases, and the mechanical characteristics such as skid resistance and ITS increase, by roughly 38% and 24%, respectively, at 0.7% W-PF. Using W-PF in the right proportions to stabilise neat asphalt for OGFC mixes thus appears promising as a long-term solution to several issues. [ABSTRACT FROM AUTHOR]

The utilization of waste into potential energy sources has received much attention in recent years. Various technology was applied with the purpose to convert waste into a useful product. One of the applications of waste to energy ideas is refuse derived fuel (RDF). In Universitas Pertamina Area, paper and plastic are two types of waste that generate large amounts of waste every day. It is due to main activities coming from educational and office activities. The generation of paper waste reached 129.1 kg/day, while 93.9 kg of plastic waste was thrown away at the temporary waste shelter every day. In this research, the various compositions of paper and plastic waste (0%, 25%, 50%, 75%, 100%) were pelletized into RDF to investigate the water content, ash content, and calorific value the RDF then compared to the standard. The result showed that all RDF compositions had passed the standard quality of RDF from the point of water content and ash content (RDF standar is <25% of water content and 20% of ash content). On the other hand, the calorific value of RDF (paper 100%) did not meet the RDF Standard (15 MJ/kg) while the rest of the RDF composition had passed the standard. When combined with the amount of waste generation, the composition of 100% plastic waste was the highest potential caloric value reached 3,954.0 MJ/day. The potential of waste utilization into RDF can be proposed as a solution for waste management, especially in the university area. [ABSTRACT FROM AUTHOR]

Every person on the planet uses solid materials. Natural resources are typically utilised in the production of new papers. Trees must be cut down to make way for new paper products. The authors want that this manuscript will raise public awareness about recycling and the relevance of solid waste management (SWM). Many forms of environmental problems may arise as a result of the depletion of natural resources. A survey was conducted for this purpose, in which 144 out of 180 participants took part. All age groups, all income levels, all types of citizens, and all levels of educated persons have participated in this study. After examining the results of this survey, it has been determined that the public is unaware of the socioeconomic benefits of recycling and solid waste management. People are also unaware of the cost-effectiveness of recycling. It could be a job-creating enterprise or industry. It became beneficial for the welfare of society, employment and environment. [ABSTRACT FROM AUTHOR]

Asbestos and gypsum ceiling board, which recently used, possess certain health risks to humans other than being environmentally-unfriendly. This project aims to investigate the potential use of waste paper in the production of ceiling material to meet the aim of producing an eco-friendly and cost-effective product. The idea of replacing the raw materials to manufacture ceiling boards with the waste paper is to carry out to ascertain its suitability as ceiling board material. The waste paper pulp was sun-dried before mixed with UF adhesive and is compressed under pressure 204 kg/m2 under a temperature of 105°C. The tests conducted include density test, moisture content test, and water absorption test. Tabulated results have shown that the material is more lightweight and comparable moisture content compared to the asbestos and gypsum board material. With the same thickness, 500g of waste paper pulp compressed into a mold with a size 450 mm x 450 mm is more suitable to be commercialized. [ABSTRACT FROM AUTHOR]

Hydroxyapatite, Ca10(PO4)6(OH2) is major mineral constituent of vertebrate bones and teeth. It is extensively used in biomedical field due to its biocompatible, bioactive and osteoconductive properties. Hydroxyapatite (HAp) has recently gained attention as efficient adsorbents, owing to its physical and chemical nature as it can substitute both cationic and anionic complexes present in an aqueous solution in its atomic arrangement. The Hydroxyapatite has been reported to be an efficient adsorbent in removing divalent heavy metal ions. In this work, an attempt has been made to synthesis hydroxyapatite by wet chemical precipitation method by extracting the calcium source from paper sludge ash. Experimental works were carried out under controlled condition by maintaining pH, temperature, stirring speed and aging period. The obtained powder is optimized at 6000C based on the TG-DTA results. The presence of hydroxyl ion in the apatite lattice was confirmed by absorption bands at 3410.15 cm−1 through FT-IR studies. The mean pore diameter and pore volume of the HAp was deducted through BET analysis as 45.22 nm and 1.7100 cm3g−1. [ABSTRACT FROM AUTHOR]

Digital transformations are happening rigorously across all industries during this IR 4.0 era in almost every developing and developed country. In particular, healthcare sectors are digitally transforming to improve their services. This article is part of Oman's healthcare sector's digital transformation initiatives. The objective of this article is to study the digital transformation in the healthcare sectors of various countries. The outcomes will be used as inputs for digital transformations of Oman's health sectors. Research papers on digital transformation in healthcare sectors from Indonesia, UAE, Saudi Arabia, USA, and Brazil were reviewed. The main observations of this review are the main challenges of digital transformations in healthcare, the recommendations to overcome these challenges, and the value creation processes. Apart from this, other important insights are drawn from this study such as examples of digital transformation frameworks in healthcare sectors, digital transformation metrics, details of widely used healthcare applications, technology adoption methods or plans, and skills development plans for healthcare professionals. This study's outcomes will be taken into account and the relevant insights will be integrated into Oman's digital transformation framework for healthcare. [ABSTRACT FROM AUTHOR]

In the world of today, receiving complaints or feedback has become fundamental for an organization aiming to improve the quality of its products or services. Similarly, public complaints must be addressed to improve government service. There is no direct or effective channel for citizens in India to address issues with the government. Later, the government launched applications for registering complaints to make the public's job easier. However, there are some issues related to those applications' equity, i.e., the difficulty faced by the rural community and uncivilized people in using those applications. This paper proposes a smart microphonic grievance system that will allow people to register complaints orally, automatically classify them, and forward them to the appropriate sector. The test results demonstrate that this system can reduce the time and process for filing complaints and that it can be used by a diverse group of individuals in society. Overall, this system is a valuable solution for improving complaint management and addressing the unique needs of rural residents. [ABSTRACT FROM AUTHOR]

Paper is a widely used material that is affected by environmental stresses and makes paper prone to damage. The paper is characterized by the absorption of water and moisture due to porosity, We have overcome this problem by employing polymer materials as water-resistant coatings acting as a barrier to protecting the paper, Polymer paper coating forms a clear membrane on the fiber forming a bridge of monomers on the surface of the paper. Two polymer coatings were used as a treatment, namely Polystyrene and sealer (alkyd resin). The results showed the possibility of enhancing the durability of the paper and preserving it from damage and deterioration. The treatment gave a decrease in moisture content, response to abrasion and scratching while increased folding tolerability, the burst strength, tear resistance, hardness compared to untreated paper and the paper porosity important indicator to overcome. The degree of brightness, the degree of color and visible light and ultraviolet radiation [UV] effect of the specimens were studied in detail. [ABSTRACT FROM AUTHOR]

We extend the inventory lot-size model in this paper to allow for products to deteriorate at variable rates, and demand is characterized by any log concave function of time that fulfils relatively mild criteria. Partial backlogging is possible with this model. The backlogging rate is a time-dependent, exponentially declining function provided by a parameter. We show that not only does the optimal replacement schedule exist, but that it is also unique. We also show that the inventory system's overall cost is a convex function of the number of replenishments. As a result, identifying a local minimum simplifies the search for the best number of replenishments. Finally, a numerical example is given to demonstrate the findings. [ABSTRACT FROM AUTHOR]

Urbanization, increase in population and change in lifestyle of human beings increased pressure on natural resources and accumulation of industrial waste in the environment. Dumping and landfilling of such industrial waste especially the solid waste is leading towards severe environmental degradation in the form of water pollution, air pollution and soil pollution etc. Due to increase in installation of more paper mills, there is rapid increase in quantity of solid waste from these industries. In recent years, utilization of lime mud generated from paper mill has been emerged as a potential method to reuse/recover the usable rich material and reduce the quantity of waste and its disposal cost for landfilling/dumping. In this experimental examination, an effort has been complete to examine the behavior of the bricks developed using the waste (lime mud) from paper industry waste and other paper sludge by partial replacing the clay to the extent from 10% to 50%. The bricks were developed by using varying composition. Later execution various tests, it has been detected that bricks made from partial replacement of clay with lime mud are light weight, having desirable compressive strength, corrosion resistant. The indoor air quality assessment of buildings made of these bricks indicted little to no impact on ambient air quality. [ABSTRACT FROM AUTHOR]

Paper soap is currently in great demand by the public because it is easy to carry everywhere. In the process, solid soap is printed as thin as paper. This paper soap will dissolve and produce foam when exposed to water. This study aims to synthesize the paper soap product against the effect of variations in the concentration of polyvinyl alcohol (PVA). PVA serves as an adhesive and forms a thin layer (film). The raw material for making soap is virgin coconut oil and NaOH as a basic soap. Basic soap is mixed with glycerin, ethylene glycol, silicone oil, olive oil, aloe vera, and perfume. After that, the mixture was added with polyvinyl alcohol with various concentrations of 5, 10, 15, and 20 percent solution. The processed soap material is then poured into a flat mold with a thickness of 0.5 mm and 1 mm. The paper soap produced was tested for water content, free fatty acids, pH and antibacterial activity test. The test results showed that the best paper soap was obtained when using a 5 percent PVA solution. The results are in accordance with the requirements of SNI 3532:2016 solid soap with a moisture content of 12%, free fatty acids 1.5%, pH 9.6 and the value of inhibition diameter on the antibacterial activity test 18.7 mm, the value stability of foam of 94% with a thickness of 0.5 mm soap. [ABSTRACT FROM AUTHOR]