Search

Polyacrylamide gel electrophoresis (PAGE) is a ubiquitous technique used in biochemical research laboratories to characterize protein samples. Despite its popularity, PAGE is relatively slow and provides limited separation resolution, especially for native proteins. This report describes the development of a microfluidic thermal gel transient isotachophoresis (TG-tITP) method to rapidly separate native proteins with high resolution. Thermal gels were employed as a separations matrix because of their unique ability to change viscosity in response to temperature. Proteins were added into thermal gel and loaded into a microfluidic device. Electrolyte optimization was conducted to achieve robust tITP to isotachophoretically preconcentrate proteins and then electrophoretically separate them. Electropherograms were collected through both time and distance to enable both small and large proteins to be measured within a single analysis. The effects of temperature were evaluated and found to exhibit a pronounced effect on the separation. Temperature gradients were then employed to alter thermal gel viscosity over time to maximize separation resolution between proteins. The results herein demonstrate how gradient TG-tITP achieves rapid, high-performance separations of native proteins. This analysis provided a wide mass range (6-464 kDa) with two-fold higher resolution than native PAGE while requiring 15,000-fold less protein loading and providing five-fold faster analysis times.

Digital PCR (dPCR) is a highly sensitive analytical technique used to quantify DNA targets. Detection sensitivity can be further enhanced by capturing target sequences onto beads for preconcentration and sample cleanup prior to analysis in microfluidic microwell arrays. However, robust digital analysis requires individual beads to be interrogated within individual wells. Fabricating microwells with dimensions ≤ 3 μm is challenging, and the high surface area-to-volume ratio of the wells leaves PCR susceptible to inhibition stemming from materials used during device processing. This report describes the development of a microfabrication procedure to create ultralow-volume wells (100 fL) for bead-based dPCR and characterize the effects of microprocessing materials on assay performance. Standard microfabrication protocols used for creating microelectronics resulted in devices with nanoscopic debris originating from photoresists used during processing. A model dPCR assay was developed to characterize the effects of this debris, which revealed variable PCR inhibition. Debris within microwells attenuated digital and analog assay signals to a greater extent than debris on the device surface. Spatial heterogeneity of debris across devices was quantified to characterize regional PCR inhibition and intra- and inter-device variability. Ultimately, a fabrication procedure was developed to create pristine microfluidic arrays using dual processes to remove positive resist and forgoing use of negative resist entirely, which enabled robust amplification with digital signals matching theoretical predictions. Results from this work catalog the unique performance artifacts from device microfabrication and provide a guide for future studies seeking to conduct robust, high-sensitivity bead-based dPCR assays.

Digital PCR (dPCR) is a highly sensitive analytical technique used to quantify DNA targets. Detection sensitivity can be further enhanced by capturing target sequences onto beads for preconcentration and sample cleanup prior to analysis in microfluidic microwell arrays. However, robust digital analysis requires individual beads to be interrogated within individual wells. Fabricating microwells with dimensions ≤ 3 μm is challenging, and the high surface area-to-volume ratio of the wells leaves PCR susceptible to inhibition stemming from materials used during device processing. This report describes the development of a microfabrication procedure to create ultralow-volume wells (100 fL) for bead-based dPCR and characterize the effects of microprocessing materials on assay performance. Standard microfabrication protocols used for creating microelectronics resulted in devices with nanoscopic debris originating from photoresists used during processing. A model dPCR assay was developed to characterize the effects of this debris, which revealed variable PCR inhibition. Debris within microwells attenuated digital and analog assay signals to a greater extent than debris on the device surface. Spatial heterogeneity of debris across devices was quantified to characterize regional PCR inhibition and intra- and inter-device variability. Ultimately, a fabrication procedure was developed to create pristine microfluidic arrays using dual processes to remove positive resist and forgoing use of negative resist entirely, which enabled robust amplification with digital signals matching theoretical predictions. Results from this work catalog the unique performance artifacts from device microfabrication and provide a guide for future studies seeking to conduct robust, high-sensitivity bead-based dPCR assays. Graphical abstract.