Search

Herein, we introduce the first relative single-particle inductively coupled plasma mass spectrometry (spICP-MS) approach where size calibration is carried out using the target NP itself measured under different instrumental conditions without external dependence on the complex and prone-to-error determination of transport efficiency or mass flux calibrations, in contrast to most spICP-MS approaches. The simple approach proposed allows determining gold nanoparticle (AuNP) sizes, with errors ranging from 0.3 to 3.1% (corroborated by HR-TEM). It has been demonstrated that the changes observed in the single-particle histograms obtained for a suspension of AuNPs under different sensitivity conditions ( n = 5) are directly and exclusively related to the mass (size) of the target AuNP itself. Interestingly, the relative nature of the approach shows that once the ICP-MS system has been calibrated with a generic NP standard, it is no longer necessary to repeat the calibration for the size determination of different unimetallic NPs carried out along time (at least 8 months), independently of their size (16-73 nm) and even nature (AuNP or AgNP). Additionally, neither the NP surface functionalization with biomolecules nor protein corona formation led to significant changes (relative errors slightly increased 1.3- to 1.5-fold, up to 7%) in the NP size determination, in contrast to conventional spICP-MS approaches where relative errors increased 2- to 8-fold, up to 32%. This feature could be especially valuable for the analysis of NPs in real samples without the need of matrix-matched calibration.

Inductively coupled plasma-mass spectrometry (ICP-MS) has been widely used in Life Sciences for the absolute quantification of biomolecules without specific standards, assuming the same response for generic compounds including complex biomolecules. However, contradictory results have been published on this regard. We present the first critical statistical comparison of the ICP-MS response factors obtained for 14 different relevant S-containing biomolecules (three peptides, four proteins, one amino acid, two cofactors, three polyethylene glycol (PEG) derivatives, and sulfate standard), covering a wide range of hydrophobicities and molecular sizes. Two regular flow nebulizers and a total consumption nebulizer (TCN) were tested. ICP-MS response factors were determined though calibration curves, and isotope dilution analysis was used to normalize the results. No statistical differences have been found for low-molecular-weight biocompounds, PEGs, and nonhydrophobic peptides using any of the nebulizers tested. Interestingly, while statistical differences were still found negligible (96-104%) for the proteins and hydrophobic peptide using the TCN, significantly lower response factors (87-40%) were obtained using regular flow nebulizers. Such differential behavior seems to be related mostly to hydrophobicity and partially to the molecular weight. Findings were validated using IDA in intact and digested bovine serum albumin solutions using the TCN (98 and 100%, respectively) and the concentric nebulizer (73 and 97%, respectively). Additionally, in the case of a phosphoprotein, results were corroborated using the P trace in parallel to the S trace used along the manuscript. This work seems to suggest that ICP-MS operated with regular nebulizers can offer absolute quantification using generic standards for most biomolecules except proteins and hydrophobic peptides.

A current remaining challenge in nanotechnology is the fast and reliable determination of the ratios between engineered nanoparticles and the species attached to their surface after chemical functionalization. The approach proposed herein based on the online coupling of asymmetric flow field-flow fractionation (AF4) with inductively coupled plasma-tandem mass spectrometry (ICP-MS/MS) allows for the first time the direct determination of such ratios in CdSe/ZnS core-shell quantum dot:rat monoclonal IgG2a antibody (QD:Ab) conjugate mixtures in a single run without any previous sample preparation (i.e., derivatization). AF4 provides full recovery and adequate resolution of the resulting bioconjugate from the excess of nanoparticles and proteins used in the different bioconjugation mixtures (1:1, 2:1, and 3:1 QD:Ab molar ratios were assessed). The point-by-point determination by ICP-MS/MS of the metal to sulfur ratios along the bioconjugate fractographic peak allowed disclosing the mixture of the different species in the bioconjugated sample, providing not only the limits of the range of QD:Ab ratios in the different bioconjugate species resulting after functionalization but also a good estimation of their individual relative abundance in the mixture. Interestingly, a wide variety of compositions were observed for the different bioconjugate mixtures studied (QD:Ab molar ratios ranging from 0.27 to 4.6). The resulting weighted QD:Ab ratio computed in this way for each bioconjugate peak matches well with both the global (average) QD:Ab ratio experimentally obtained by the simpler peak area ratio computation and the theoretical QD:Ab molar ratios assayed, which internally validates the procedure developed.

Absolute protein quantification methods based on molecular mass spectrometry usually require stable isotope-labeled analogous standards for each target protein or peptide under study, which in turn must be certified using natural standards. In this work, we report a direct and accurate methodology based on capLC-ICP-QQQ and online isotope dilution analysis for the absolute and sensitive quantification of intact proteins. The combination of the postcolumn addition of 34 S and a generic S-containing internal standard spiked to the sample provides full compound independent detector response and thus protein quantification without the need for specific standards. Quantitative recoveries, using a chromatographic core-shell C4 column for the various protein species assayed were obtained (96-100%). Thus, the proposed strategy enables the accurate quantification of proteins even if no specific standards are available for them. In addition, to the best of our knowledge, we obtained the lowest detection limits reported in the quantitative analysis of intact proteins by direct measurement of sulfur with ICPMS (358 fmol) and protein (ranging from 7 to 15 fmol depending on the assayed protein). The quantitative results for individual and simple mixtures of model proteins were statistically indistinguishable from the manufacturer's values. Finally, the suitability of the strategy for real sample analysis (including quantitative protein recovery from the column) was illustrated for the individual absolute quantification of the proteins and whole protein content in a venom sample. Parallel capLC-ESI-QTOF analysis was employed to identify the proteins, a prerequisite to translate the mass of quantified S for each chromatographic peak into individual protein mass.

The synthesis and characterization of a novel water-compatible microsized material, based on fluorescent conjugated polymers (CPs), and its applicability for optical sensing of inorganic ions of environment interest (copper and cyanide) in water media is here described. Polyfluorene-based fluorescent CPs were synthesized and functionalized with imidazole moieties (selective recognition element) and a terminal double bond (covalently linked to an organic matrix) through a postfunctionalization strategy. Further, microspheres of the novel imidazole-functionalized fluorescent CPs, able to work in water media, were synthesized via a microemulsion and polymerization procedure. The synthesized imidazole-functionalized CP microspheres were then evaluated as fluorescence "turn-Off" sensing materials for Cu(2+) detection in aqueous media. Analyte detection was based on the quenching effect of the Cu(2+), selectively recognized by the imidazole group, on the polymer fluorescence emission. The developed optosensor exhibits a detection limit of 1 μg/L for the determination of Cu(2+) in water with a reproducibility of 4%. The synthesized microsized material was also evaluated for the "turn-on" optosensing of cyanide in water, measuring the recovery of the emission signal from the CP that has been previously deactivated by the presence of quencher species. The "turn-On" optosensor allows the selective determination of free cyanide in aqueous solution with high sensitivity (detection limit of 18 μg/L), obtaining a reproducibility of 2.9%. A high sample throughput (between 7 and 12 samples per hour) was achieved in both cases. Analytical applicability of the fluorescent CP microsphere materials has been successfully demonstrated by tap and mineral water analysis.

A microsecond-pulsed direct current glow discharge (GD) was interfaced and synchronized to a time-of-flight mass spectrometer MS(TOF) for time-gated generation and detection of elemental, structural, and molecular ions. In this way, sequential collection of the mass spectra at different temporal regimes occurring during the GD pulse cycle is allowed. The capabilities of this setup were explored using bromochloromethane as model analyte. A simple GD chamber, developed in our laboratory and characterized by a low plasma volume minimizing dilution of the sample but showing great robustness to the entrance of organic compounds in the microsecond-pulsed plasma, has been used. An exhaustive analytical characterization of the GD-MS(TOF) prototype has been performed. Calibration curves for bromochloromethane observed at the different time regimes of the GD pulse cycle (that is, for elemental, fragment, and molecular ions from the analyte) showed very good linearity for the measurement of the different involved ions, with precisions in the range of 7-13% (relative standard deviation). Actual detection limits obtained for bromochloromethane were in the range of 1-3 microg/L for elements monitoring in the GD pulse "prepeak", in the range of 11-13 microg/L when monitoring analyte fragments in the plateau, and about 238 microg/L when measuring the molecular peak in the afterpeak regime.

Aiming at enhancing the advantages of traditional molecularly imprinted polymers (MIPs) for chemical sensing, a new MIP design approach introducing an internal heavy atom in their polymeric structure is described. Based on the heavy-atom effect, the novel polymer allows one to perform room-temperature phosphorescence (RTP) transduction of the analyte. The synergic combination of a tailor-made MIP recognition with a selective RTP detection is a novel concept for optosensing devices which is assessed here for simple and highly selective determination of trace amounts of fluoranthene in water. The noncovalent MIP was synthesized using the laboratory-synthesized tetraiodobisphenol A as one of the polymeric precursors and fluoranthene as template. In the presence of an oxygen scavenger, the iodide included in the polymeric structure induced efficient RTP emission from the analyte, once recognized by the MIP. The developed optosensing system has demonstrated a high specificity for fluoranthene against other polycyclic aromatic hydrocarbons. Detection limit for the target molecule was 35 ng/L (5-mL sample injections), and the linear range extended above 100 microg/L of the analyte. The polymer can be easily regenerated for subsequent sample injections (at least up to 450 cycles) with acetonitrile. The synthesized sensing material showed good stability for at least 6 months after preparation. The feasibility of monitoring fluoranthene in real samples was successfully evaluated through the analysis of five spiked river water samples.