Search

Confocal and multiphoton optical imaging techniques have been powerful tools for evaluating the performance of and monitoring experiments within microfluidic devices, but this application suffers from two pitfalls. The first is that obtaining the necessary imaging contrast often requires the introduction of an optical label which can potentially change the behavior of the system. The emerging analytical technique stimulated Raman scattering (SRS) microscopy promises a solution, as it can rapidly measure 3D concentration maps based on vibrational spectra, label-free; however, when using any optical imaging technique, including SRS, there is an additional problem of optical aberration due to refractive index mismatch between the fluid and the device walls. New approaches such as 3D printing are extending the range of materials from which microfluidic devices can be fabricated; thus, the problem of aberration can be obviated simply by selecting a chip material that matches the refractive index of the desired fluid. To demonstrate complete chemical imaging of a geometrically complex device, we first use sacrificial molding of a freeform 3D printed template to create a round-channel, 3D helical micromixer in a low-refractive-index polymer. We then use SRS to image the mixing of aqueous glucose and salt solutions throughout the entire helix volume. This fabrication approach enables truly nonperturbative 3D chemical imaging with low aberration, and the concentration profiles measured within the device agree closely with numerical simulations.

Soybeans are a commodity crop of significant economic and nutritional interest. As an important source of protein, buyers of soybeans are interested in not only the total protein content but also in the specific amino acids that comprise the total protein content. Raman spectroscopy has the chemical specificity to measure the twenty common amino acids as pure substances. An unsolved challenge, however, is to quantify varying levels of amino acids mixed together and bound in soybeans at relatively low concentrations. Here we report the use of transmission Raman spectroscopy as a secondary analytical approach to nondestructively measure specific amino acids in intact soybeans. With the employment of a transmission-based Raman instrument, built specifically for nondestructive measurements from bulk soybeans, spectra were collected from twenty-four samples to develop a calibration model using a partial least-squares approach with a random-subset cross validation. The calibration model was validated on an independent set of twenty-five samples for oil, protein, and amino acid predictions. After Raman measurements, the samples were reduced to a fine powder and conventional wet chemistry methods were used for quantifying reference values of protein, oil, and 18 amino acids. We found that the greater the concentrations (% by weight component of interest), the better the calibration model and prediction capabilities. Of the 18 amino acids analyzed, 13 had R(2) values greater than 0.75 with a standard error of prediction c.a. 3-4% by weight. Serine, histidine, cystine, tryptophan, and methionine showed poor predictions (R(2)0.75), which were likely a result of the small sampling range and the low concentration of these components. It is clear from the correlation plots and root-mean-square error of prediction that Raman spectroscopy has sufficient chemical contrast to nondestructively quantify protein, oil, and specific amino acids in intact soybeans.

Fourier-transform infrared imaging (FT-IR) is a well-established modality but requires the acquisition of a spectrum over a large bandwidth, even in cases where only a few spectral features may be of interest. Discrete frequency infrared (DF-IR) methods are now emerging in which a small number of measurements may provide all the analytical information needed. The DF-IR approach is enabled by the development of new sources integrating frequency selection, in particular of tunable, narrow-bandwidth sources with enough power at each wavelength to successfully make absorption measurements. Here, we describe a DF-IR imaging microscope that uses an external cavity quantum cascade laser (QCL) as a source. We present two configurations, one with an uncooled bolometer as a detector and another with a liquid nitrogen cooled Mercury Cadmium Telluride (MCT) detector and compare their performance to a commercial FT-IR imaging instrument. We examine the consequences of the coherent properties of the beam with respect to imaging and compare these observations to simulations. Additionally, we demonstrate that the use of a tunable laser source represents a distinct advantage over broadband sources when using a small aperture (narrower than the wavelength of light) to perform high-quality point mapping. The two advances highlight the potential application areas for these emerging sources in IR microscopy and imaging.