Search

Introduction: The finite element method has been extensively used to analyze the mechanical behavior of endodontic rotary files under bending and torsional conditions. This methodology requires elevated computer-aided design skills to reproduce the geometry of the endodontic file, and also mathematical knowledge to perform the finite element analysis. In this study, an automated procedure is proposed for the computerized generation and finite element analysis of endodontic rotary files under bending and torsional conditions. Methods: An endodontic rotary file with a 25mm total length, 0.25mm at the tip, 1.20mm at 16mm from the tip, 2mm pitch and squared cross section was generated using the proposed procedure and submitted for analysis under bending and torsional conditions by clamping the last 3mm of the endodontic rotary file and applying a transverse load of 0.1N and a torsional moment of 0.3N·cm. Results: The results of the finite element analyses showed a maximum von Mises stress of 398MPa resulting from the bending analysis and a maximum von Mises stress of 843MPa resulting from the torsional analysis, both of which are next to the encastre point. Conclusions: The automated procedure allows an accurate description of the geometry of the endodontic file to be obtained based on its design parameters as well as a finite element model of the endodontic file from the previously generated geometry.

The aim of the present study is to present a repeatable, reproductible, and accurate morphometric measurement method for measuring and quantifying the area and volume of cement that remains after fixed lingual multibracket appliance debonding, enamel loss after fixed lingual multibracket appliance debonding, and the volume of cement used to adhere fixed lingual multibracket appliances. Ten conventional lingual brackets were cemented in 10 extracted teeth embedded into an epoxy resin model simulating a dental arch. This model was scanned before and after bonding the lingual brackets, after debonding, and after polishing the surfaces. We also performed a Micro-Computed Tomography scan of the lingual brackets used. Afterward, the standard tessellation language (STL) digital file was aligned, each tooth was segmented individually, and the file was re-aligned using engineer morphometry software. Inter-operator and intra-operator comparative analyses were performed using the ANOVA test, and the repeatability and reproducibility of the morphometric measurement technique were analyzed using Gage R&R statistical analysis. Repeatability showed 0.07% and 0.16% variability associated with the area and volume measures, respectively, while reproducibility showed 0.00% variability associated with the area and volume measures, respectively. In conclusion, the morphometric measurement technique is a repeatable, reproductible, and accurate morphometric measurement method for quantifying the area and volume of cement that remains after fixed lingual multibracket appliance debonding, enamel loss after fixed lingual multibracket appliance debonding, and the volume of cement used to adhere fixed lingual multibracket appliances.

The aim of the present study was to compare the area and volume of remaining cement after lingual and buccal multibracket appliance debonding. Further, the area and volume of cement remaining and the area and volume of enamel were also analyzed using a morphometric digital measurement technique. Ten buccal and 10 lingual multibracket appliances were cemented in 20 extracted teeth embedded into an epoxy resin model simulating a dental arch. The models were scanned before bonding the lingual and buccal multibracket appliances, after debonding the lingual and buccal multibracket appliances, and after polishing the remaining cement. Afterwards, the standard tessellation language (STL) digital files were aligned, segmented, and realigned by using engineer morphometry software. A comparative analysis was performed using Student’s t test statistical analysis. Lingual appliances showed statistically significantly (p < 0.001) less area (7.07 ± 4.85 mm2) and volume (0.87 ± 1.34 mm3) of remaining cement than the area (21.99 ± 4.18 mm2) and volume (p = 0.002) (3.48 ± 0.96 mm3) of buccal appliances. Moreover, lingual appliances showed statistically significantly (p = 0.001) less area (4.48 ± 3.08 mm2) and volume (0.13 ± 0.15 mm3) of remaining cement after polishing than the area (12.22 ± 5.98 mm2) and volume (p = 0.004) (0.70 ± 0.56 mm3) of buccal appliances. Lingual multibracket appliance therapy leads to less area and volume of cement remaining after multibracket appliance debonding and less area and volume of cement remaining after cement polishing than buccal multibracket appliance therapy; however, the area and volume of enamel removed after cement polishing were similar between both lingual and buccal multibracket appliance therapies.

To analyze the influence of the operator experience on the accuracy of orthodontic self-tapping micro-screws placement, a total of 60 orthodontic self-tapping micro-screws were randomly distributed into two study groups: Group A. Orthodontic micro-screws placement by an orthodontist with 10 years of experience (n = 30); and B. Orthodontic micro-screws placement by an orthodontist student without experience (n = 30). Cone-beam computed tomography scans and intraoral scans were performed before and after the orthodontic self-tapping micro-screws placement and uploaded in 3D implant-planning software to analyze the deviation angle and the horizontal deviation measured at the coronal entry point and apical endpoint between orthodontic micro-screws planned and performed. In addition, intraoperative complications such as root perforations after orthodontic self-tapping micro-screws placement and fracture of the orthodontic self-tapping micro-screws during their placement were also analyzed. The paired t-test revealed statistically significant differences at the apical endpoint (p = 0.004) of planned and performed orthodontic self-tapping micro-screws between the orthodontist with 10 years of experience and the orthodontist student without experience. However, the paired t-test revealed no statistically significant differences at the coronal entry point (p = 0.220) and angular deviations (p = 0.602) of planned and performed orthodontic self-tapping micro-screws between the orthodontist with 10 years of experience and the orthodontic student without experience. Furthermore, five root perforations were observed in the no experience study group and three orthodontic self-tapping micro-screws were fractured in each study group. In conclusion, the results show that the greater experience of the operator influences the accuracy of orthodontic micro-screws placement, resulting in less intraoperative complications.

The aim of this study was to show a novel and accurate digital measurement protocol by analyzing the area and volume for interproximal tooth enamel surface reduction. In total, 14 lower teeth from all dental sectors were embedded into an epoxy resin and distributed as the lower dental arch, keeping the contact points. The experimental model was submitted to an intraoral digital impression before and after interproximal tooth enamel surface reduction using air-rotor strips and then re-contouring and polishing the interproximal enamel surfaces. These steps helped obtain standard tessellation language (STL) digital files. Furthermore, each tooth in the preoperative and postoperative full-arch STL digital files was segmented individually and aligned to analyze the area and volume of the interproximal tooth enamel surface reduction using engineering morphometry software. Descriptive analysis of the area and volume of the interproximal tooth enamel surface reduction was performed using a Student t-test. Higher enamel reduction area (3.53 ± 3.08 mm2) and volume (0.32 ± 0.22 mm3) values were shown on the distal surface compared with the area (2.97 ± 3.05 mm2) and volume (0.22 ± 0.16 mm3) of the enamel reduction on the mesial surface measured using the morphometric measurement digital protocol. The morphometric measurement protocol is an accurate digital measurement protocol for analyzing the area and volume of interproximal enamel surface reduction.

Background: The aim of this study was to analyze the effects of the time of use (TU) and sterilization cycles (SC) of endodontic reciprocating files on cyclic fatigue resistance. Methods: One-hundred-and-twenty (120) Procodile NiTi endodontic reciprocating instruments were selected at random and distributed into the following study groups: A: 0 sterilization cycles/0s time of use (n = 10); B: 0/60 (n = 10); C: 0/120 (n = 10); D: 1/0 (n = 10); E: 1/60 (n = 10); F: 1/120 (n = 10); G: 5/0 (n = 10); H: 5/60 (n = 10); I: 5/120 (n = 10); J: 10/0 (n = 10); K: 10/60 (n = 10); and L: 10/120 (n = 10). A dynamic cyclic fatigue device was designed using computer-aided design/computer-aided engineering (CAD/CAE) technology and created with a 3D printer to simulate the pecking motion performed by the clinician. Failure of the endodontic rotary instrument was detected by a light-emitting diode-light-dependent resistor (LED-LDR) system controlled by an Arduino driver complex and management software. The results were analyzed using the ANOVA test. Results: All pairwise comparisons presented statistically significant differences between the time to failure, number of cycles to failure and number of cycles of in-and-out movement for the time of use study groups (p < 0.001), but not in the number of sterilization cycles (p > 0.05). Conclusions: The time of use of NiTi endodontic reciprocating files negatively affects dynamic cyclic fatigue resistance. Dynamic cyclic resistance is not affected by the number of sterilization cycles.