Search

The biodegradation kinetics of paper materials with various chemical additives was studied, focusing on their potential tunability. Paper materials with additives, including retention aid, hydrophobic agent, and wet and dry strength agents, were explored in two forms: disintegrated fiber and paper form. Using the Gompertz equation, biodegradation kinetics were modeled to calculate the lag phase, initial biodegradation rate, and ultimate biodegradation extent. All paper materials showed higher biodegradation extents than microcrystalline cellulose (MCC) due to the highly biodegradable nature of hardwood bleached pulp. Disintegrated paper materials exhibited similar lag phase values and ultimate biodegradation to MCC regardless of treatment, while punched paper materials showed noticeable differences, suggesting that fiber disintegration plays a critical role in initiating biodegradation. Hydrophobic and wet strength treatments, such as alkyl ketone dimer (AKD) and wet-strength agents (PAE), respectively, significantly increased the lag phase, but their ultimate biodegradation extent remained intact. These findings highlight that the biodegradability of paper materials can be preserved even after chemical treatments, underscoring their environmentally friendly potential.

For a hygiene paper such as tissue and towel, strength, softness, and absorbency are known as attributes that a user is looking for. It is proposed here that purchasing decisions are likely to be influenced by in-use experiences, which may be quite different from the physical properties measured with current standardized tests. There have been continuous efforts on developing physical test methods to replace subjective in-use tests because the benefits of the former are too significant to be overlooked. This paper considered some in-use test methods for paper towel products that can be carried out by panel members quickly in the course of sensory panel testing. In addition, laboratory tests were developed in an attempt to quantify such input. The sensory panel testing showed that (wet) strength and absorbency were the key contributions to the performance of paper towels. Softness did not show any significant contribution to it. Wet strength showed a high correlation with absorbency. The (wet) ball burst strength had the highest correlation with the in-use strength. Although both the tensile strength and the ball burst strength had a high correlation with preference, the ball burst tester is preferred because more reproducible and simpler to operate.

The increasing rates of illicit behaviors, particularly financial crimes, e.g., bank fraud and tax evasion, adversely affect national economies. In such cases, using nondestructive methods, scientists must evaluate relevant documents carefully to preserve their value as evidence. When forensic laboratories analyze paper as evidence, they typically investigate its origin and date of manufacture. If a document’s date is earlier than the earliest availability of the paper used in its creation, then this anachronism indicates that the document has been backdated. This study investigated weave marks and drainage marks for forensic purposes. Machine learning models for forensic document examination were developed and evaluated. The partial least squares discriminant analysis (PLS-DA), support vector machine (SVM), and artificial neural network (ANN) classification models achieved F1-scores of 0.903, 0.952, and 0.931, respectively. In addition, to enhance model effectiveness and construct a robust model, variables were selected using the VIP scores generated by the PLS-DA model. As a result, the SoftMax classifier in the ANN model maintained its performance with an F1-score of 0.951 even with a 50% reduction in the number of input variables.

The disposable cup market has long relied on paperboard with a fossil-based polymer coating as a replacement for 100% plastic cups. Paperboards with biobased or biodegradable polymer coatings are aimed at reducing the fossil resource consumption of the packaging sector. However, as their properties are inherently different from traditional, fossil-based materials, they can face runnability issues. In order to establish a connection between certain material properties and runnability issues, four coated paperboard materials with differing surface and strength properties were converted into 250 mL/8 oz disposable drinking cups. The materials included two single-side extrusion-coated paperboards and two two-sided dispersion-coated paperboards. The cups were manufactured in two separate runs with minor machine adjustments to affect the resulting cup geometry. A comparison of the manufactured cups and material properties revealed the materials’ coefficient of friction to be the major cause of runnability issues or defects. Other suspected properties affecting the performance of cup materials included bending stiffness and compression strength.

This research investigated the influence of the layered structure of paper on its selected strength properties. Two types of cellulose pulp were used: unbleached kraft pine pulp (UBSK) and unrefined bleached birch kraft pulp (BHK). Multi-ply papers were obtained from layers of appropriate grammage formed separately and bonded in a wet state. Paper layers were formed from primary pulps (UBSK and BHK) or their mixtures (three-ply UBSK-BHK paper and three-ply UBSK-BHK-UBSK paper), from which various variants of laboratory paper samples were made. This work focused on three-layer papers. The obtained laboratory sheets were analysed for changes in tear resistance, tensile strength, bursting strength, short span compression strength (SCT), and corrugating medium test (CMT). In most cases, three-layer structures were characterised by higher strength parameters than single-layer papers. The tear strength and SCT of papers consisting of three layers formed from both mixed pulps were slightly lower than those of solid papers. The results demonstrate the feasibility of producing three-ply paper with significantly reduced variability in parameters such as elongation and bursting strength, which are inherently subject to high variability.

Pretreated carboxymethylated nanofibrillated cellulose (CM-NFC) was tested as a strength enhancer for specialty paper, such as banknotes made from cotton linter mixed pulp (CLMP). The pretreatment agent was cationic poly(acrylamide) (C-PAM). The CM-CMF prototype was supplied by a Korean manufacturer. Laboratory tests and pilot trials were performed to evaluate the strength enhancement of banknotes incorporated with surface-modified CM-NFC and determine the process problems encountered in a pilot paper machine. The CM-NFC was surface modified with 0.1% C-PAM without any agglomerates. The prepared laboratory handsheets had high paper strength, which was attributed to the higher nanofibril content of surface-modified CM-NFC compared with that of unmodified CM-NFC. Pilot trials showed that the incorporation of 3% surface-modified CM-NFC was highly effective in promoting the strength of banknote without low retention and drainability on the wet-end part of the pilot paper machine. Therefore, surface-modified CM-NFC at a controlled dosage could be used as a strength enhancer for specialty paper without incurring serious problems in a paper mill.

The potential of paper and paperboard as fiber-based materials capable of replacing conventional polymer-based materials has been widely investigated and evaluated. Due to paper’s limited extensibility and inherent heterogeneity, local structural variations lead to unpredictable local mechanical behavior and instability during processing, such as mechanical forming. To gain a deeper understanding of the impact of mechanical behavior and heterogeneity on the paper forming process, the Finite Element Method (FEM) coupled with continuum modeling is being explored as a potential approach to enhance comprehension. To achieve this goal, utilizing experimentally derived material parameters alongside stochastic finite element methods allows for more precise modeling of material behavior, considering the local material properties. This work first introduces the approach of modeling heterogeneity or local material structure within continuum models, such as the Stochastic Finite Element Method (SFEM). A fundamental challenge lies in accurately measuring these local material properties. Experimental investigations are being conducted to numerically simulate mechanical behavior. An overview is provided of experimental methods for material characterization, as found in literature, with a specific focus on measuring local mechanical material structure. By doing so, it enables the characterization of the global material structure and mechanical behavior of paper and paperboard.

The mineralization of inorganic components in paper sludge offers potential for their re-use in various fields. This study synthesized carbonates based on the minerals present in paper sludge and aimed to investigate the control of particle size distribution and particle shape of the synthesized carbonates. First, the physicochemical and thermal properties of paper mill sludge and ash were evaluated using a spectrophotometer, XRF, and TGA. Paper sludge ash was obtained by incinerating the paper sludge, followed by a carbonation reaction using CO2 gas injection and pH neutralization to produce recycled fillers. The average particle size, crystal lattice structure, and morphology of the recycled fillers were analyzed using a particle size analyzer, XRD, and FE-SEM. The results indicate that the recycled filler produced from coating paper sludge exhibited similar brightness and morphology to conventional paper-based fillers, suggesting its potential to replace commercial PCC (Precipitated Calcium Carbonate). In contrast, the recycled filler manufactured using old corrugated container mill sludge was deemed unsuitable due to its low hydration activity.

As a way to reduce microplastics or nano-plastics in the ocean, it is of interest to develop biodegradable paper-based drinking straws to replace non-degradable plastic drinking straws. Primary questions to be addressed include how to design suitable coatings for paper drinking straws. Such coatings not only need to resist water. In addition, consumers have high expectations for the strength of a drinking straw. It is proposed here to replace non-biodegradable polypropylene, which is presently the main component of straws, with biodegradable and hydrophobic coating components via an entropy-driven approach. It is further proposed to develop colored paper-based drinking straws with cellulose nematic liquid crystal photonic pigments as a way to make the product stand out visibly, while at the same time mediating the usage of toxic chemical pigments.

Grease-proof paper is an energy-demanding paper product to manufacture, especially during refining and dewatering. Increases in energy efficiency in either stage could result in major savings. This article investigates the potential gains with addition of a stepwise progression vacuum suction box to the forming section during production. For both a lighter, 50 g/m2, and a heavier paper grade, 100 g/m2, with a pulp-drainability of 86 °SR, a stepwise progression vacuum suction box in four steps would result in increased dryness, simultaneously with decreased energy expenditure. The observed effects were higher for the lower basis weight paper (50 g/m2). Both basis weights experienced clogging of the forming fabric due to the high degree of refining. This adversely affected the dewatering rate, decreasing the amount of air pulled through the paper even when increasing the vacuum pressure. When a stepwise progression suction box in four steps was compared to a single vacuum suction box, there was a 14% increase in dryness for lighter paper, over an equal energy consumption, measured as amount of air pulled through the paper. For the 100 g/m2 paper, the increase in dryness was 3% compared to the 50 g/m2 paper run over a single vacuum suction box. The results show great promise for energy savings when utilizing stepwise progression suction box dewatering for grease-proof paper production.

A smooth and dense surface of the base paper is advantageous when the goal is to apply a liquid coating as a barrier layer. For such a base paper, non-wood fibers derived from wheat straw could be an alternative to wood fibers. In this research paper, wheat straw pulp was refined with different beating levels (up to 600 revolutions) followed by different calendering pressure loads (up to 50 N/mm) to test its influence on mechanical and surface properties. Alkyl ketene dimer (AKD) was used as sizing agent with concentrations up to 0.2 wt% followed by a mineral-based precoating to test its influence on the smoothness. Eucalyptus pulp was chosen as a benchmark. After beating, the initial Schopper-Riegler degrees of 28 °SR increased to 56 °SR. Beating also increased the tensile index from 24 to 49 Nm/g, the burst index from 1.2 to 2.8 kPa·m²/g, and the tear index decreased from 3.3 to 2.8 mN·m2/g. Calendering reduced the initial roughness of 370 mL/min to 30 mL/min. When precoated and calendered again, the value was lowered to 15 mL/min. In summary, wheat straw paper is a relevant alternative to wood-derived base paper to produce barrier papers. Compared to eucalyptus, wheat straw paper showed better smoothness and much lower air permeability indicating excellent suitability for barrier coating.

A pre-treatment process was evaluated in this work for wastewater from paper recycling using microwave technology followed by rapid precipitation of contaminants through centrifugation. Artificial neural networks (ANNs) were used to analyze and optimize the turbidity values. Thirty experimental runs were utilized including microwave (MW) power, duration, centrifuge time, and centrifuge speed as input variables, generated by the Central Composite Full Design (CCFD) approach. The experimental turbidity ranged from 8.1 to 19.7 NTU, while predicted values ranged from 8.4 to 19.7 NTU by ANN. The ANN model showed a robust prediction performance with low mean squared error values during training and testing. Moreover, high R2 values showed a remarkable agreement between the experimental observations and ANN predictions. The results obtained from the input values (A:150.00, B:60.00, C:15.00, D:30.00) of sample 2, which gave the lowest turbidity value, showed the most removal of pollution. The results obtained from the input values (A:250.00, B:60.00, C:7.00, D:20.00) of sample 30, which gave the highest turbidity value, showed the least removal of pollution. The results showed that increasing RPM and time of the centrifugation process significantly affected the removal of pollution in wastewater.

The primary aim of this research was to explore the feasibility of producing environmentally friendly composite materials by employing diverse hybrid matrices consisting of dammar natural resin, supplemented with small proportions of two synthetic resins: one epoxy and the other acrylic. A blend of paper and chicken feathers served as the reinforcing elements. The fabrication of these composite materials utilized a hand layup technique. Targeted for applications in the furniture industry or interior design, their mechanical properties were assessed through various tests. Specimens were obtained from the manufactured samples and subjected to evaluations for tensile strength, compression, flexure, vibrations, Shore hardness, and water absorption. Results indicated that irrespective of the testing method employed, the mechanical strength properties exhibited a decline with an increase in the percentage of dammar in the hybrid resins, whereas the elasticity properties demonstrated an increase with this percentage.

Grease-proof paper is an energy-demanding paper product to manufacture, especially during refining and dewatering. Increases in energy efficiency in either stage could result in major savings. This article investigates the potential gains with addition of a stepwise progression vacuum suction box to the forming section during production. For both a lighter, 50 g/m², and a heavier paper grade, 100 g/m², with a pulpdrainability of 86 °SR, a stepwise progression vacuum suction box in four steps would result in increased dryness, simultaneously with decreased energy expenditure. The observed effects were higher for the lower basis weight paper (50 g/m²). Both basis weights experienced clogging of the forming fabric due to the high degree of refining. This adversely affected the dewatering rate, decreasing the amount of air pulled through the paper even when increasing the vacuum pressure. When a stepwise progression suction box in four steps was compared to a single vacuum suction box, there was a 14% increase in dryness for lighter paper, over an equal energy consumption, measured as amount of air pulled through the paper. For the 100 g/m² paper, the increase in dryness was 3% compared to the 50 g/m² paper run over a single vacuum suction box. The results show great promise for energy savings when utilizing stepwise progression suction box dewatering for grease-proof paper production. [ABSTRACT FROM AUTHOR]

Size presses on paper machines are used to apply a solution of a polymer – usually starch – to the surface of the sheet and thereby to increase the stiffness, surface strength, and printing quality of the product. This article reviews publications dealing with the size press equipment, the materials, and factors affecting both the operating efficiency and attributes of the resulting paper. The emergence of film-press equipment (e.g. blade-metering size presses) in the 1980s has greatly decreased the frequency of web breaks and increased productivity. Starch technology at the size press, though relatively mature, continues to evolve. By adjustment of starch attributes, solids levels, and incorporating other additives, modern papermakers can tune size press outcomes to meet a range of paper product requirements, including strength, hydrophobicity, and the reduction of air permeability. By application of various synthetic polymers, mineral particles, and even nanocellulose in combination with starch or other base polymers, there is potential to extend the technology to meet a range of future needs for paper products.

A pre-treatment process was evaluated in this work for wastewater from paper recycling using microwave technology followed by rapid precipitation of contaminants through centrifugation. Artificial neural networks (ANNs) were used to analyze and optimize the turbidity values. Thirty experimental runs were utilized including microwave (MW) power, duration, centrifuge time, and centrifuge speed as input variables, generated by the Central Composite Full Design (CCFD) approach. The experimental turbidity ranged from 8.1 to 19.7 NTU, while predicted values ranged from 8.4 to 19.7 NTU by ANN. The ANN model showed a robust prediction performance with low mean squared error values during training and testing. Moreover, high R² values showed a remarkable agreement between the experimental observations and ANN predictions. The results obtained from the input values (A:150.00, B:60.00, C:15.00, D:30.00) of sample 2, which gave the lowest turbidity value, showed the most removal of pollution. The results obtained from the input values (A:250.00, B:60.00, C:7.00, D:20.00) of sample 30, which gave the highest turbidity value, showed the least removal of pollution. The results showed that increasing RPM and time of the centrifugation process significantly affected the removal of pollution in wastewater. [ABSTRACT FROM AUTHOR]

Paper pulp is a lignocellulosic fibrous material used in the industrial production of paper and board products. In addition to cellulose and hemicellulose, paper pulp contains 1 to 20% lignin, depending on the raw materials and pulping process used. Lignin is a heterogenous aromatic polymer that is hydrophobic and more resistant to microbial degradation compared to the easily biodegradable cellulose and hemicellulose. In this study, the biodegradation of paper pulps containing varying amounts of lignin was examined in soil and marine environments using ISO testing methods. Lignin significantly reduced the mineralization of paper pulps to CO2 in both environmental conditions, and a strong inverse correlation between lignin content and the mineralization to CO2 was observed. A similar impact was observed with natural materials containing lignin, such as birch sawdust. Since the calculation of biodegradability in most ISO and EN standards is based solely on the concept of mineralization to CO2, materials containing lignin can receive poor values in these tests. The implications of this for standardized requirements of biodegradability and possible options to overcome testing deficiencies are discussed.

Nanofibrillated cellulose (NFC) and its combined usage with cationic starch and a cationic copolymer of acrylamide were studied in relation to the properties of paper. Independent pulp treatments using additives separately included 0%, 5%, 10%, and 15% refined long fiber pulp, 3 and 6% NFC, 0.75 and 1.5% cationic starch and 0.07% and 0.15% cationic polyacrylamide and combined treatments. Handsheets were made of the above treatments, and finally their optical and microscopic properties were evaluated. Increasing the NFC content to 6% increased the brightness and yellowness of the white liner by 13% and 21%, respectively. The liner opacity was also reduced by 1%. Additionally, increasing NFC by 6% compared to imported long fibers, the brightness and yellowness of the white liner increased 5.44% and 6.3%, respectively. The liner opacity was also reduced by 1%. A 1.5% cationic starch addition to NFC increased the brightness of the white liner by 4.4%, its whiteness increased 1.5%, and its yellowness increased 2.1%. The opacity of the liner was also reduced by 7.1%. The use of NFC and cationic starch can improve the optical properties of the white liner, while imported long fibers may be problematic.

The effect of shredded waste office paper was considered when producing one-layered particleboard. Five different mixing ratios of shredded waste office paper/wood particles were used (0/100, 25/75, 50/50, 75/25, and 100/0) and two amounts of urea formaldehyde (UF) resin (10% and 15%). The boards were tested for their physical and mechanical properties, including modulus of elasticity (MOE), bending strength (MOR), and internal bond (IB) strength, in accordance with the European Norm (EN) standards. All properties of the boards were found to be improved via increasing the resin content. The 15% UF-bonded board with 100% wood particles had the highest MOR, whereas the board containing 100% wastepaper for 15% UF had the highest MOE. However, there was no statistical difference between the board types. Although increasing wastepaper content in the board negatively affected the IB, the usage of wastepaper up to 25% was shown to be acceptable as a raw material in the production of particleboard. None of the prepared boards met the EN 312 (1999) requirements for thickness swelling. The boards made from shredded waste office paper were more suitable for dry and indoor use. [ABSTRACT FROM AUTHOR]

Impinging air jets can be used to dewater, heat, and dry the web of tissue paper. High velocities of the air jets degrade the paper, and appropriate adjustments to the jet velocity and the distance of the nozzle from the surface of the wet web are crucial to obtain the highest quality product. This work investigated the correlation between the velocity of the air jet and the strength of paper subjected to the impingement method. Papers with an initial moisture content of 20% and various pulp mixes were tested, and the physical properties of papers were explored. After impinging an air jet, different tensile strength limits were obtained in the machine and cross directions. The paper had lower apparent density and higher roughness compared to classical pressing. The dependence of tensile strength and roughness on the fibers composition also was determined. Increasing the amount of eucalyptus fibers in impingement dewatered paper resulted in a decrease in its tensile strength and roughness. The value of elongation before breaking was the highest for softwood papers after the impingement method. The maximum velocity of an air jet that can be used to dewater or dry paper without the risk of damage to the papers was determined.

Poly(3-hydroxybutyrate) (PHB), a biodegradable polymer, has been studied as a substitute for petroleum-based polymers used for barrier coating to improve the barrier and mechanical properties of paper. In this study, ethyl cellulose (EC), a cellulose derivative, was used to prepare a polymer blend for enhancing the barrier properties of PHB. The prepared PHB/EC blend was then applied as a paper coating material. Additionally, the barrier and mechanical properties of the PHB/EC blend-coated paper based on the PHB/EC mixing ratio and coating weight were analyzed. The results showed that the EC could act as a binder for the PHB/EC blend-coated paper. Consequently, the PHB/EC blend-coated paper exhibited significant improvements in mechanical and barrier properties, including a substantial increase of over 100% in internal bond strength, more than 20% in tensile strength, exceeding 60% enhancement in water resistance, and a remarkable increase of over 90% in air permeability.

Herein, the challenge of accurately classifying the manufacturing origin of printing paper, including continent, country, and specific product, was addressed. One-dimensional convolutional neural network (1D CNN) models trained on infrared (IR) spectrum data acquired from printing paper samples were used for the task. The preprocessing of the IR spectra through a second-derivative transformation and the restriction of the spectral range to 1800 to 1200 cm-1 improved the classification performance of the model. The outcomes were highly promising. Models trained on second-derivative IR spectra in the 1800 to 1200-cm-1 range exhibited perfect classification for the manufacturing continent and country, with an impressive F1 score of 0.980 for product classification. Notably, the developed 1D CNN model outperformed traditional machine learning classifiers, such as support vector machines and feed-forward neural networks. In addition, the application of data point attribution enhanced the transparency of the decision-making process of the model, offering insights into the spectral patterns that affect classification. This study makes a considerable contribution to printing paper classification, with potential implications for accurate origin identification in various fields.

Due to the high wastepaper recyclability and water-loop system closure, packaging paper mills struggle with increased fines, causing runnability issues. Cellulase enzymes are a preferred treatment choice for the improvement of the pulp refining in stock preparation area but are not widely used or easy to introduce in the production process. Different cellulase enzymes were tested, and those with the highest activity were introduced to the white-water (WW) samples with the aim to reduce fines content as potentially new enzyme applications on the paper machine. The first portion of the study involved the development of an experiment model to find and confirm the optimal enzyme process parameters (40 °C, pH 5.7, reaction time 3 h, and 0.18% v/v enzyme addition) for laboratory made white-water. The second portion of the study included turbidity, colloidal charge, flow cytometry (FCM), and chemical oxygen demand (COD) analysis on industrial and laboratory made white-water samples at optimized process parameters. Obtained results corresponded to reduced fines content in white-water samples, which justified commercial usage of cellulase enzymes on recycled paper machine short loop and potentially increased machine runnability without negative influence on wastewater treatment plant.

This study evaluated the production of marine biodegradable plastics, specifically polyhydroxyalkanoates (PHAs), using waste paper from food containers as a novel material source. The results showed that adding dilute sulfuric acid as a pretreatment may have a negative impact on enzyme hydrolysis efficiency. Without pretreatment, the highest glucose concentration was observed in the 50-min heating group. In the experimental group with 1% dilute sulfuric acid as a pretreatment, the highest average glucose concentration was observed in the 25-min treatment group. In flask scale experiments, the C/N ratio was controlled at 10, 20, and 30. The results showed that when the C/N ratio was 10, the PHA/CDM ratios were 16.3 and 23.6 at 48 and 72 h, respectively. After 96 h of cultivation using hydrolysis liquid from the waste paper container as the sole carbon source in a 5-L scale experiment, the PHA/CDM ratio was 28.7 and the PHA concentration was 0.95 g/L. The potential bacterial strain in this study was confirmed to be a Bacillus genus bacterium after strain identification. The signal peaks indicated that the PHA obtained from the Bacillus sp. production process was PHB.

Hemp hurd fiber, a low-value waste stream from the hemp industry, has potential downstream applications as an alternative to non-renewable plastics for single-use food service ware and packaging applications. Packaging paper substrates made from chemically pulped hemp hurd, mixed in varying ratios with bleached thermomechanical radiata pine pulp were developed and tested. Handsheets were characterized using several mechanical property tests including tensile strength, tearing resistance, burst strength, short-span compression, ring crush, together with Gurley air resistance, contact angle, and Cobb60 tests. Generally, addition of hemp hurd fibers significantly improved handsheet mechanical properties. Hot-pressing of the handsheets so as to approximate molded fiber thermoforming further enhanced their performance, with pure hemp hurd handsheets having the highest mechanical properties and barrier performance. A prototype was successfully thermoformed from hemp fiber, demonstrating overall feasibility of this fibre source for molded fibre objects.

Flow and spontaneous imbibition phenomena in porous media are important for various industrial applications, including printing and medical lateral flow assays. Their quantitative characterization is important to better understand and select the appropriate raw materials. However, standard methods often require time-consuming tests, and/or expensive equipment. Different time scales must be considered, limiting the range of possible characterization tools. A novel experimental approach based on image analysis for characterizing spontaneous imbibition processes is presented. Hence, ultra-fast diffusion may be quantitatively characterized. Models are issued from the literature to consider physical phenomena at small (milliseconds) and medium range (seconds) of time scales. The obtained experimental data fit with theoretical results, providing valuable insights into the understanding of fluid flow behavior at different time scales. Furthermore, the identification of some physical properties for either the fluid, or the substrate, based on the theoretical models are possible, as the contact angle, which remains to be otherwise challenging. This study contributes to bridging the gap between spontaneous imbibition and capillary phenomena at different time scales, their modeling, and a characterization of material and/or fluid properties paving the way for enhanced understanding and control of fluid behavior in porous media. Different papers are considered to illustrate the method.

The effects of laboratory beating on unbleached regular grade pine kraft pulp (UPKP), pre-treated with commercial cellulase/hemicellulase enzymatic preparation (C/HEP) were assessed using degrees of Schopper-Riegler (°SR) and fibre-quality numbers (FQN). The tests showed a significant increase in the °SR (used in papermaking laboratories and industry to assess the degree of beating) of the UPKP after its enzymatic pre-treatment in the amount of 0.25 to 5.0 mL/kg of pulp and beating. However, only a several percent reduction of beating time was observed when the effect of this pretreatment of pulp on the speed of its beating was determined using another method. The treatment of the pulp selected for research with C/HEP before beating negatively influenced its strength properties after this process. The results correlated well with the most important basic fiber properties from the standpoint of papermaking.

The effect of shredded waste office paper was considered when producing one-layered particleboard. Five different mixing ratios of shredded waste office paper/wood particles were used (0/100, 25/75, 50/50, 75/25, and 100/0) and two amounts of urea formaldehyde (UF) resin (10% and 15%). The boards were tested for their physical and mechanical properties, including modulus of elasticity (MOE), bending strength (MOR), and internal bond (IB) strength, in accordance with the European Norm (EN) standards. All properties of the boards were found to be improved via increasing the resin content. The 15% UF-bonded board with 100% wood particles had the highest MOR, whereas the board containing 100% wastepaper for 15% UF had the highest MOE. However, there was no statistical difference between the board types. Although increasing wastepaper content in the board negatively affected the IB, the usage of wastepaper up to 25% was shown to be acceptable as a raw material in the production of particleboard. None of the prepared boards met the EN 312 (1999) requirements for thickness swelling. The boards made from shredded waste office paper were more suitable for dry and indoor use.

γ-Valerolactone (GVL) is a promising biomass-based platform compound that can be used for the removal of hemicellulose in pulp. In this study, a paper-grade pulp was treated using GVL to generate dissolving pulp for viscose production. The GVL concentration, treatment temperature, and reaction time had significant effect on the hemicellulose dissolution. The dissolving pulp with α-cellulose content of 92.3% and hemicellulose content of 5.45% was achieved with 60% GVL at 120 °C for 2 h. The Fock reactivity and intrinsic viscosity of the obtained dissolving pulp were 54.6% and 595 mL/g, which is comparable with the commercial product. In addition, GVL spent liquor was also recycled and reused to upgrade paper-grade pulp. By using purified recycled GVL to treat original pulp, the Fock reactivity of pulp was improved, and the cellulose content of as-prepared upgraded pulp increased to 92.1%, which was close to the cellulose content of dissolving pulp obtained from fresh GVL solution, while the intrinsic viscosity decreased significantly to 598 mL/g. Therefore, the efficient reuse of GVL not only ensured the high quality of dissolving pulp, but it also saved production costs and reduced environmental pollution.

A sodium bentonite product (nanoclay) was added to a polyhydroxybutyrate/ ethyl cellulose (PHB/EC) blend coating agent, and the impact of the nanoclay content on the properties of the coated paper was investigated. The organically treated nanoclay exhibited enhanced compatibility with the PHB/EC blend, ensuring uniform dispersion within the coating layer and improving the barrier properties of the coated paper. The mechanical properties of the PHB/EC blend-coated paper with nanoclay demonstrated ductile behavior, reducing the tensile strength and increasing the elongation. However, at higher nanoclay loadings, specifically up to 25%, aggregation among nanoclay particles occurred. This hindered the enhancement of barrier properties, thereby decreasing the degree of elongation. Incorporating nanoclay as a filler in the PHB/EC blend at suitable levels showed potential for further enhancing the barrier properties and ensuring economic feasibility in the production of packaging paper.

Paper coated with natural materials has advantages over paper coated with fossil resources, including easy recycling, renewable components, and cost-effective formulation. Coating the paper surface with thyme oil has antibacterial and antioxidant properties and is known to improve packaging product quality. In the current study, the water resistance of the materials was measured by the Cobb30 values. The base paper, the starch-coated paper, and the thyme oil and starch-coated paper had Cobb30 values of 20, 17.5, and 15.7 g/m2, respectively. The tensile strength index of uncoating and coating paper samples was, respectively (machine direction M.D.) 64.3 and 64.7, and (cross direction C.D.) 32.2 and 37.2. The bursting strength index results were 72.7 and 84.0. Hence, according to the tensile strength results, the treated paper burst strength values were higher than the base paper samples. The starch and thyme oil coatings formed a film layer on the paper surface, which may have helped impart better burst-strength properties. Besides, compared to the untreated base papers, the surface of the coated papers was denser and smoother, with a less porous structure, according to SEM results. In addition, resistance features of papers that are desired in the end-use of paper are shown in this work based on paper strength property tests.

Size presses on paper machines are used to apply a solution of a polymer - usually starch - to the surface of the sheet and thereby to increase the stiffness, surface strength, and printing quality of the product. This article reviews publications dealing with the size press equipment, the materials, and factors affecting both the operating efficiency and attributes of the resulting paper. The emergence of film-press equipment (e.g. blademetering size presses) in the 1980s has greatly decreased the frequency of web breaks and increased productivity. Starch technology at the size press, though relatively mature, continues to evolve. By adjustment of starch attributes, solids levels, and incorporating other additives, modern papermakers can tune size press outcomes to meet a range of paper product requirements, including strength, hydrophobicity, and the reduction of air permeability. By application of various synthetic polymers, mineral particles, and even nanocellulose in combination with starch or other base polymers, there is potential to extend the technology to meet a range of future needs for paper products. [ABSTRACT FROM AUTHOR]

It is difficult to predict index values or stock prices with a single financial formula. They are affected by many factors, such as political conditions, global economy, unexpected events, market anomalies, and the characteristics of the relevant companies, and many computer science techniques are being used to make more accurate predictions about them. This study aimed to predict the values of the XKAGT index by using the monthly closing values of the Borsa Istanbul (BIST) Forestry, Paper and Printing (XKAGT) index between 2002 and 2023, and the machine learning techniques artificial neural networks (ANN), random forest (RF), k-nearest neighbor (KNN), and gradient boosting machine (GBM). Furthermore, the performances of four machine learning techniques were compared. Factors affecting stock prices are generally classified as macroeconomic and microeconomic factors. As a result of examining the studies on determining the macroeconomic factors affecting the stock markets, 10 macroeconomic factors were determined as input. The macroeconomic variables used were crude oil price, exchange rate of USD/TRY, dollar index, BIST100 index, gold price, money supply (M2), S&P 500 index, US 10-year bond interest, export-import coverage rate in the forest products sector, and deposits interest rate. It was determined that all machine learning techniques used in the study performed successfully in predicting the index value, but the k-nearest neighbor algorithm showed the best performance with R2=0.996, RMSE=71.36, and a MAE of 40.8. Therefore, in line with the current variables, investors can make analyzes using any of the ANN, RF, KNN, and GBM techniques to predict the future index value, which will lead them to accurate results.

Tetra Pak® paper and PE (polyethylene) wastes were evaluated to obtain a new composite material with awareness of environmental responsibility. Fillers and coupling agents were used for this joining process. Calcite (CaCO3), boric acid (H3BO3), SPT (Sodium Perborate Tetrahydrate / NaBO3.4H2O), titanate, MAPE (maleic anhydride grafted polyethylene, and vinyltriethoxysilane (C8H18O) composites were produced in 30 × 30 cm plates. A total of 30 samples were prepared as 5 mg flour for thermogravimetric analysis (TGA). Samples were observed in a thermal analyzer at 10, 15, or 20 °C/min heating rate in nitrogen atmosphere. Graphs were obtained as a result of TGA, and the activation energies were calculated using these graphs. The activation energy was calculated using the Flynn-Wall-Ozawa method. The determined activation energies of the composites were close to each other for each temperature group. In the samples using calcite and vinyltriethoxysilane, relatively higher activation energies were observed in comparison to the samples with boric acid and MAPE.

Wood-based paper fibers are inherently biodegradable. In contact with moist soil and in compost, papermaking fibers are readily broken down by soil microbes. Resistance to biodegradation is needed, as paper is used for special applications such as mulching in agriculture and forestry, the coating of construction materials, and for packing and wrapping under conditions where packaging materials may be exposed to contact with moist soil or other type microbial active contamination. A preceding study showed that paper chemical crosslinking with glyoxal, citric acid (CA), or methylated 1,3-dimethylol-4,5-dihydroxyethylene urea (mDMDHEU) results in substantially improved paper wet strength and lower paper water absorbency. The present study examined the efficiency of chemical crosslinking treatments with CA and with mDMDHEU to decrease the biodegradation rate of laboratory paper sheets and a sack paper, both made of kraft fibers. The biodegradation was examined using a 48-h enzymatic degradation test and a 2-month soil burial test. The results indicate that chemical crosslinking is an effective non-biocidal method for making sulphate kraft paper more resistant to biodegradation. In some end-uses, improved resistance to biodegradation, along with improved paper wet performance, can enhance paper performance comparable to plastic films.

For about two millennia, paper has served as a main medium for preservation of people’s ideas, stories, contracts, and art. This article reviews what is known about the various components that make up paper from the perspective of their long-term stability under typical storage conditions. Literature evidence is considered relative to the susceptibility of different paper components to embrittlement, acid hydrolysis, microbiological attack, and discoloration, among others. The cellulose that makes up a majority of most paper items is demonstrably stable enough to persist for many hundreds of years on the shelves of archival collections, though it is susceptible to acid-catalyzed hydrolysis, which can be accelerated by byproducts of decomposition. Though less attention has been paid to the archival performance of various minor components of modern paper products, evidence suggests that at least some of them are subject to likely breakdown, embrittlement, or decay in the course of prolonged storage. Based on these considerations, one can envision different categories of paper that can be expected to meet different levels of storage stability: ancient recipes for handmade papermaking, e.g. washi and hanji, archival-grade paper products, ordinary modern alkaline paper products, and paper manufactured without concerns for its longevity.

Paper, which is in fact a very complex cellulose-based product derived from different lignocellulosic resources, is usually regarded as a simple omnipresent commodity in our lives. Wood fibers derived from trees are the most employed sources for papermaking purposes. From an environmental protection perspective, and for their essential role in our life (they give us the life itself through their foliar system supporting the photosynthesis process), trees should not be extensively cut down and they should be used less and less for papermaking. Thus, employment of non-woody alternative sources for papermaking could be exploited more as an attractive and feasible option.

This study evaluated the production of marine biodegradable plastics, specifically polyhydroxyalkanoates (PHAs), using waste paper from food containers as a novel material source. The results showed that adding dilute sulfuric acid as a pretreatment may have a negative impact on enzyme hydrolysis efficiency. Without pretreatment, the highest glucose concentration was observed in the 50-min heating group. In the experimental group with 1% dilute sulfuric acid as a pretreatment, the highest average glucose concentration was observed in the 25-min treatment group. In flask scale experiments, the C/N ratio was controlled at 10, 20, and 30. The results showed that when the C/N ratio was 10, the PHA/CDM ratios were 16.3 and 23.6 at 48 and 72 h, respectively. After 96 h of cultivation using hydrolysis liquid from the waste paper container as the sole carbon source in a 5-L scale experiment, the PHA/CDM ratio was 28.7 and the PHA concentration was 0.95 g/L. The potential bacterial strain in this study was confirmed to be a Bacillus genus bacterium after strain identification. The signal peaks indicated that the PHA obtained from the Bacillus sp. production process was PHB. [ABSTRACT FROM AUTHOR]

Polyamidoamine epichlorohydrin (PAAE) is a permanent wet strength resin used in papermaking. When applied to paperboard, some amount of resin is retained in the sheet, and some is lost to the white water. The papermaker usually knows the amount of PAAE charged to the pulp but has no idea how much chemical is retained in the sheet. In addition, the influence of PAAE dosage, freeness, zeta potential, and pulp kappa number variability on PAAE retention is not well understood. Factorial design experiments using unbleached and bleached softwood (loblolly pine) kraft pulps were conducted to understand the factors that affect PAAE retention. The results revealed that PAAE retention, wet tear index, and tensile index not only depended on the PAAE charged of the pulp but also depended significantly on the pulp freeness. In lieu of freeness, zeta potential data can be used to predict PAAE retention. In addition, at similar freeness, bleached pulp has the highest retention of PAAE compared to low and high kappa unbleached kraft pulps. The results also suggest that lignin may have potential as a wet strength agent.

This research investigated the influence of the layered structure of paper on its selected strength properties. Two types of cellulose pulp were used: unbleached kraft pine pulp (UBSK) and unrefined bleached birch kraft pulp (BHK). Multi-ply papers were obtained from layers of appropriate grammage formed separately and bonded in a wet state. Paper layers were formed from primary pulps (UBSK and BHK) or their mixtures (threeply UBSK-BHK paper and three-ply UBSK-BHK-UBSK paper), from which various variants of laboratory paper samples were made. This work focused on three-layer papers. The obtained laboratory sheets were analysed for changes in tear resistance, tensile strength, bursting strength, short span compression strength (SCT), and corrugating medium test (CMT). In most cases, three-layer structures were characterised by higher strength parameters than single-layer papers. The tear strength and SCT of papers consisting of three layers formed from both mixed pulps were slightly lower than those of solid papers. The results demonstrate the feasibility of producing three-ply paper with significantly reduced variability in parameters such as elongation and bursting strength, which are inherently subject to high variability. [ABSTRACT FROM AUTHOR]

Microfibrillated cellulose (MFC) was prepared from post-consumer old corrugated container (OCC) material, which was first disintegrated in water, cleaned to remove impurities, and then fibrillated by grinding. Those processed MFCs were treated with in-situ formation of calcium carbonate by adding calcium oxide and injecting carbon dioxide into the mixture up to the ratio of 1:40 (MFC : calcium carbonate) by weight. The MFCs had a dark brown color initially but turned into high brightness materials similar to commercial ground calcium carbonate (GCC) after the in-situ formation process. The MFCs that had calcium carbonate attached on their surfaces, which were lengthy and flexible, were called flexible calcium carbonate from OCC (FCCO). Paper containing FCCO gave higher bulk, higher stiffness, and higher tensile index without lowering smoothness when compared to the paper containing commercial GCC. However, brightness was slightly lowered because of initial low brightness of the OCC. This study also demonstrated the feasibility to substitute wood fibers up to 5% with FCCO without lowering essential properties for printing paper. Benefits of the waste paper are savings of both wood resources and production cost.

Wood-based paper fibers are inherently biodegradable. In contact with moist soil and in compost, papermaking fibers are readily broken down by soil microbes. Resistance to biodegradation is needed, as paper is used for special applications such as mulching in agriculture and forestry, the coating of construction materials, and for packing and wrapping under conditions where packaging materials may be exposed to contact with moist soil or other type microbial active contamination. A preceding study showed that paper chemical crosslinking with glyoxal, citric acid (CA), or methylated 1,3-dimethylol-4,5-dihydroxyethylene urea (mDMDHEU) results in substantially improved paper wet strength and lower paper water absorbency. The present study examined the efficiency of chemical crosslinking treatments with CA and with mDMDHEU to decrease the biodegradation rate of laboratory paper sheets and a sack paper, both made of kraft fibers. The biodegradation was examined using a 48-h enzymatic degradation test and a 2-month soil burial test. The results indicate that chemical crosslinking is an effective non-biocidal method for making sulphate kraft paper more resistant to biodegradation. In some end-uses, improved resistance to biodegradation, along with improved paper wet performance, can enhance paper performance comparable to plastic films. [ABSTRACT FROM AUTHOR]

Effects of cellulose nanofibers (CNF) and cationic starch (CS) were evaluated as coating components relative to the physical and mechanical properties of fluting papersheets fabricated from recycled corrugated cardboard fibers. Fabricated fluting papers were subjected to size press applications by three different coating blends. Coating suspensions were prepared at various concentrations of CNF (0.5%, 1%, 2%, 3%, and 4%) and 4 wt% CS, and the same amounts of CS/CNF. The paper sheets were fabricated using size press machine as three-time repetitive applications, followed by one-time drying section, and compared to uncoated, CScoated, and CNF-coated papers. The application of CNF suspensions increased tensile indices up to 11.7%. Moreover, CS/CNF suspensions resulted in a 67.2% increase in tensile index values. The coating of CS/CNF suspensions increased the burst index values by 163% at the CS+1%CNF concentration when compared to the control pulp. Surface application of prepared suspensions reduced the porosity of the samples under all conditions. The highest reduction in the air permeability was observed in the CS+4%CNF-coated samples as 91.5%. It can be concluded that the superficial applications of CNF on the physical and mechanical properties of recycled fluting paper was more effective in the presence of CS. [ABSTRACT FROM AUTHOR]

The influences of nano-chitosan and cationic polyacrylamide (cPAM) on the optical and mechanical properties of paper made from chemi-mechanical pulp (CMP) were investigated. Bleached chemi-mechanical pulp (CMP) was selected as the control sample. The cPAM was considered at four levels (0%, 0.25%, 0.5%, and 0.75%), while chitosan was added to the CMP suspension at three levels (0%, 1%, and 2%). Paper test specimens were prepared according to TAPPI standards with a basis weight of 60 g/m2, and their optical and mechanical properties were measured. The results indicated that the opacity, greenness, tear strength, burst strength, and Gurley seconds were increased, whereas brightness, water absorption, and a* factor were decreased by increasing the amount of cPAM. Adding chitosan to CMP increased the a* factor, tear strength, breaking length, burst strength, Gurley seconds, water absorption, and greenness in the resulting paper. When polyacrylamide and nano-chitosan were added simultaneously to CMP, the brightness, water absorption, and greenness of the resulting paper decreased, but opacity, burst strength, tear strength, and air resistance had an appropriate increase. In all treatments, the best results were found at 1% chitosan and 0.5% cPAM due to favorable optical and mechanical properties.

The effects of the pre-coating color formulation, dwell time, and coat weights of pre- and top- coating layers on print mottle of double-coated paper were investigated using an octave band filtering image processing technique. To investigate the effect of pre-coating color formulations, six types of coating colors were used. Mottle index and coefficient of variance (COV) of double-coated paper increased as the size of pre-coating pigment particles decreased, which was attributed to the reduction in relative pore size of the pre-coating layer. Decreasing the dwell time decreased transfer time from the coating head to dryer of a Maiyoh coater. As the transfer time to dryer decreased, the mottle index and COV increased because of uneven distribution of latex within the coating layer. Pre-coat weight was found to have a greater impact on print mottle than the top-coat weight.

This article substantiates the possibilities of replacing commercial wood with raw materials made from industrial hemp hurd (hemp-woody core) for the production of unbleached and bleached paper pulps. A comparative analysis of the mechanical characteristics of sheets of paper prepared in the Rapid-Köthen apparatus and obtained from pulp obtained from commercial wood and hemp-woody core (HWC) was undertaken. The objective of this study was to determine the effect of mechanical refining of a pulp on the production of microcrystalline cellulose (MCC) from HWC. It was shown that an increase in the pulp refining degree from 15 °SR to 83 °SR led to a decrease in the degree of polymerisation of MCC from 272 to 75, the hydrochloric acid concentration from 73 to 45.63 g/L, and the hydrolysis time from 120 min to 60 min. With the addition of 5% MCC obtained from hemp-woody core, the mechanical properties of laboratory paper sheets from HWC were improved until they met ISO 12625-4-2017 (2017) requirements for NS-2. The results obtained support using hemp-woody core for the production of MCC.

Hydrogen peroxide is an environmentally friendly bleaching chemical that is widely used in alkaline media in the pulp and paper industry. In this study, unconventional reaction conditions of the conventional bleaching P-stage were performed to evaluate its effect on cellulose. The objective was to “tailor” the cellulose degradation according to different applications, such as dissolving pulps. Different operating conditions were studied: pH variation (alkaline or acidic medium), as well as the addition of Cu(II) or the Cu(II)-phenanthroline complex. The hypotheses considered were (1) Using H2O2 in unconventional conditions will favor hemicelluloses removal after depolymerization and will lead to the desired cellulose degradation, and (2) H2O2 oxidation carried out under unconventional conditions will favor the dissolving ability of cellulose.

Fold cracking, which reduces the economic feasibility of paper-making, is a localized surface deformation caused by extreme bending stress. Most paper products, such as base paper and coated paper, generate fold cracking during folding processing. To control fold cracking, the mechanical properties of the base paper can be strengthened, and the flexibility of the structure can be increased by controlling the modification in pulp fibers and stock preparation conditions. This study analyzed the changes in the mechanical properties of high-grammage paper in response to the addition of precipitated calcium carbonate (PCC) and cationic starch (C-starch). The application of inorganic filler (PCC) drastically reduced the internal bond strength and tensile strength, causing fold cracking, whereas C-starch increased the bond strength between fibers, which improved the tensile strength, internal bond strength, and elongation. However, when applied independently, fold cracking occurred because of extreme increase or decrease in strength. Therefore, the combined application of C-starch and PCC made it possible to form a paper-based structure with high fold cracking resistance. Moreover, when the fold cracking resistance was excellent, the mechanical properties were balanced without being biased in one direction even under conditions of relatively low mechanical properties.

Research into paper-based devices and ionic liquids has increased considerably in the past few years. Thus, the combination of paper-based devices with ionic liquids is also becoming an increasingly frequent research subject. However, the influence of the ionic liquid on the paper properties has been hardly considered. In this paper, the influence of a hydrophobic ionic liquid (1-butyl-3-methylimidazolium bis(trifluoromethyl-sulfonyl)imide) on the mechanical properties of laboratory paper, isotropic and oriented, made from eucalyptus sulfate and cotton linters, is investigated. The tensile strength, elastic modulus, and breaking strain of papers saturated with ionic liquid were about 60 to 90% of the dry paper characteristics. In contrast to water, the breaking strain did not increase in the presence of the ionic liquid. This is because the ionic liquid only slightly swelled the fibers.