Search

Large parts of Asia, Europe, and the eastern USA have high population concentrations in moderate seismic regions (MSR), where very large earthquakes are rare. With rampant construction in the cities located in MSRs, a relatively moderate earthquake can turn into a catastrophe. Limiting the collapse has been the conventional performance objective for regions with high seismicity. However, this does not necessarily translate into a more desirable target of life-safety under design basis earthquake in MSRs. The present paper investigates the seismic performance of non-ductile reinforced concrete (RC) buildings that were common before the advent of modern design standards, and are found in very large numbers. An analytical model capturing the shear failure is employed using a drift-based limit state material. The results show that a hybrid index captures moderate damage more accurately than the prevalent drift-based index. The paper further shows that while a generic ground motion suite accurately estimates the median fragility, it fails to capture the uncertainty. A 7-story non-ductile RC archetype building was found to be at a collapse prevention risk of 2 × 10–4. The seismic risk deaggregation reveals that seismic risk consistency can be enhanced by explicit specification of the seismic forces for retrofitting. The study shows that the stringent seismic risk targets can be met by non-ductile buildings in MSR, provided they are designed or retrofitted with constraints on strong column weak beam factors. The study will facilitate in developing a scheme for prioritizing and devising the retrofit of pre-modern code and non-ductile deficient buildings. [ABSTRACT FROM AUTHOR]

In this paper, the dynamic response of two 21-story buildings was studied to assess the influence of higher modes in their structural performance. While the first building was structured with ductile moment-resisting steel frames and exhibits a global shear-dominated lateral deformation, the second one uses ductile concentrically braced steel frames and has a global bending-type response. Buildings were virtually located in a soft-soil condition of the lake-bed zone in Mexico City. Nonlinear pushover and dynamic analyses were performed through OpenSees on a detailed 3D-model with plasticity spread along the elements. For this purpose, a set of accelerograms recorded during the Mexico Earthquake of September 19, 2017, were selected, and adjusted to represent the actual seismic hazard at the site. A frequency-domain system identification technique was applied to identify the dynamic characteristics of buildings through a moving-window Fourier analysis, that allows for the estimation of the contribution of higher-modes to their overall nonlinear dynamic response. A ratio of the elastic spectral pseudo-accelerations corresponding to the first two vibration modes is proposed to quantitatively anticipate cases and conditions for which the second mode adversely affects the structural performance of upper stories. The discussion includes a comparative study from the lateral global response of the analyzed models. [ABSTRACT FROM AUTHOR]

The track structure has an effect on the dynamic characteristics of the bridge structure, which makes the seismic response of the bridge structure complicated. In this paper, an assessment method is proposed to evaluate the seismic risk of bridge structure, including over-limit risk and over-limit scale. Based on a newly proposed simplified model with high accuracy and high computational efficiency, a total of 3000 calculation conditions are analyzed and the sample stability of response is validated to ensure the reliability of the seismic risk analysis. The seismic risks in the longitudinal direction of the track-bridge model are compared with that of the trackless model, and the influence of the constraint effect of China Railway Track System II ballastless track structure on the seismic risk of the structure is obtained. The influence of the number of spans and PGA on track constraints is also revealed. The analysis results, based on a large number of samples, show that although track constraints can reduce the seismic risk of some phenomenon, such as girders' collision, the expected enhancement of longitudinal seismic safety of the system cannot be guaranteed in general, especially when the number of spans is large. However, it is noted that the track constraint can effectively control the over-limit scale of the system, which can reduce the expected repair cost after an earthquake. Therefore, it can be considered that the positive effect of the track constraints is more significant in economy than in structural safety when the bridge is subjected to a longitudinal earthquake excitation. [ABSTRACT FROM AUTHOR]

In this paper a novel approach named Multi Pier Macro MPM method is proposed for seismic analysis of steel moment frames. Based on the model an arbitrary multi-bay and multi-story moment frame is substituted by a single bay braced frame consists of two piers and two braces at each story. Piers are continuous and braces are pinned to piers. Both piers and braces are 1D truss elements. The axial, flexural and shear stiffness of the moment frame are provided by axial behavior of piers and braces. MPM method was benchmarked against four steel moment frames including two mid-rise and two high-rise buildings. The seismic responses of equivalent braced frames including maximum floor displacements and story drifts was compared with original moment frames responses as exact results, by means of Non-linear Static Procedure NSP and Non-linear Response History Analysis NL-RHA. NL-RHA was performed using twelve ground motion records scaled to Maximum Design Earthquake MDE and Maximum Considered Earthquake MCE hazard intensities. The results proved the simplified braced frame is able to estimate the seismic responses of mid and high-rise moment frame buildings with high accuracy meanwhile the analysis time and computational cost were limited remarkably. [ABSTRACT FROM AUTHOR]

The seismic response of monopile foundations is a growing area of research as the offshore wind industry expands worldwide, including in earthquake prone regions of the world. This paper presents dynamic centrifuge tests aimed at investigating the dynamic response of monopiles in both dry and saturated sandy soils. The latter case includes soil liquefaction under strong input motions, with measured excess pore pressures indicating liquefaction. The natural frequency of the monopile-soil system is experimentally determined by measuring the response to a sine sweep motion. Strong earthquakes are then applied at this frequency and its harmonics. This paper discusses the response of the monopile in terms of the peak accelerations observed in the dry and saturated tests, as well as using response spectra and amplification ratios. The dynamic bending moments along the pile are also measured to infer the bending moment profile with depth. Finally, two identical monopiles are pushed-over in each of the centrifuge tests to establish the pre and post-earthquake monotonic response, including the lateral stiffness and capacity, which are compared for the dry model tests and the saturated case. [ABSTRACT FROM AUTHOR]

This paper documents performance of cast-in-place reinforced concrete (RC) buildings in the Durrës municipality during Albania earthquake of November 26, 2019 (MW 6.4). Both mid- and high-rise RC buildings were affected by the earthquake, experiencing structural and/or non-structural damage and even collapse in some cases. The authors performed a reconnaissance study after the earthquake and were involved in seismic assessment of buildings in the affected area. Besides the observations related to physical damage of RC buildings, the paper also presents results of a statistical analysis of damaged RC buildings in the Durrës municipality. The discussion in the paper is focused on damage patterns and failure mechanisms that are relevant for the seismic response of RC structures. Most common damage pattern observed after the earthquakes was related to masonry infill walls, which experienced damage and failure in some cases, and affected the performance of adjacent RC columns due to the infill/frame interaction. Taller RC framed buildings (10 storeys and higher) were expected to have RC shear walls; however, these walls were reportedly absent in the damaged buildings of this type. In some cases, masonry infill walls (instead of RC shear walls) were used in the elevator shaft areas, which resulted in inadequate seismic performance. A case study has been presented to illustrate seismic behaviour of mid-rise and high-rise cast-in-place RC buildings in the November 2019 earthquake, and is based on post-earthquake field observations and a detailed seismic assessment of two earthquake-damaged buildings. Finally, relevant lessons and recommendations are presented in light of the observed performance of RC buildings. [ABSTRACT FROM AUTHOR]

The response of a two-storey RC school building in the town of Argostoli, Cephalonia Island, Greece, during the seismic sequence of January and February 2014, is examined. The structure was built following an older generation of seismic codes dating from the 1950s, which provide limited strength and ductility against lateral loads. Despite the severity of ground shaking and the two successive events, the building suffered relatively minor damage, like most of the RC buildings in the town. Following a short presentation of some basic seismological, structural and geotechnical aspects of the seismic sequence, the paper focuses on the seismic performance of the structure at hand. To this end, a series of detailed non-linear static and time-history dynamic analyses are reported, which highlight the interplay of soil, foundation and superstructure in modifying the seismic demand. It is demonstrated that SSI had an unexpectedly important (detrimental) role in the behaviour of the structure, increasing its natural period by about 25% and aggravating ductility demand in almost all columns, despite the moderately soft soil conditions (average VS = 180 m/s). The results shed light on the seismic performance of the building and help drawing conclusions on the engineering effects of the 2014 Cephalonia earthquake sequence. [ABSTRACT FROM AUTHOR]

Seismic losses due to earthquakes have been shown to have significant economic, social and environmental consequences. Over recent years, research to predict potential economic and social impact due to seismic risk has been increasing. Recognizing that the traditional philosophy of life safety design can lead to extensive damage and demolition which has a large environmental cost, incorporating environmental impacts associated with the expected seismic damage over a building's life is a key step as the building industry moves towards both sustainable and seismically resilient design. This paper introduces a framework that uses environmental indicators quantifying losses from seismic response that can then be used to advocate for a change in seismic performance objectives. First, existing literature and previously developed approaches for quantifying potential environmental impact due to seismic damage are summarized. Next, performance based earthquake engineering concepts are used to demonstrate a probabilistic approach to quantify potential environmental impacts using a range of environmental and resource use indicators over the life span of a case study building. In addition, a case study is presented to compare different environmental indicators between a Code Minimum building and the same building redesigned for a higher seismic performance. The majority of the composition of the environmental indicator values are from the inclusion of the non-repairable scenario, and from the repair activities, the majority of the impacts are from damage to drift sensitive components including curtains walls, partitions and elevators. For the Code Minimum building the non-repairable scenario contributes to between 8 to 11% the total seismic cost. For the Stronger Stiffer building, the non-repairable scenario contributes around 3% of the initial impact. Neglecting non-repairable scenarios does significantly reduce the potential environmental impacts when analyzing buildings designed for current code minimum structural standards. [ABSTRACT FROM AUTHOR]

Summary: The aim of this paper is to demonstrate the efficiency of a low-cost and sustainable timber-based energy dissipation system with recentering ability, which can be used as a seismic isolation system or a tuned mass damper for the seismic protection of structures in developing or developed countries. The system, defined as Dovetail with SPrings (Dove-SP), utilizes the attractive properties of timber to store CO2, thus reducing the carbon footprint of the existing energy dissipation systems: It comprises two timber slabs that are designed to slide against each other in a motion that is restrained by a dovetail sliding joint. Two sliding interfaces that allow this sliding motion at an attractively low friction coefficient are experimentally investigated: A PVC sand-wich (PVC-s) sliding interface, comprising a thin layer of sand that is sand-wiched between two PVC layers and a timber sand-wich sliding interface consisting of a thin layer of sand encapsulated between two beech timber surfaces. A set of low-cost steel springs is designed and installed on both sides of the dovetail joint to recenter the structure back to its original position after the end of an earthquake ground motion excitation. A novel, low-cost and deformable wood material fabricated from delignified balsa wood is used to reduce the pounding effects before the activation of the steel springs. The seismic behavior and the recentering ability of the novel timber-based energy dissipation system subjected to an ensemble of recorded earthquake ground motion excitations was experimentally investigated through a large-scale shaking table investigation at ETH Zurich. [ABSTRACT FROM AUTHOR]

This paper investigates the effects of soil–structure interaction and site amplification on the seismic response of one of the towers of the Theodosian walls of Constantinople during the Kocaeli earthquake in 1999, that largely damaged it. The interacting system is first analysed in the frequency domain by the well-known replacement oscillator model, turning out that the effect of soil–structure interaction could be relevant. The complete system is then examined by the direct approach considering non linearity of the behaviour of both the structure and the soil. The failure mechanism detected from where stress and plasticization concentrate into the masonry panels is consistent with the out-of-plane mechanism of one of the tower façades triggered by the reference earthquake. The focus was then set on the effectiveness of some retrofitting interventions, including the lateral disconnection of the embedded sides of the tower from the surrounding soil, the soil treatment by grouted columns and the classical technique for masonry rehabilitation. Even though the latter choice is the most common one, retrofitting interventions concentrated into the soil could be effective as well. Their use should be properly considered when the scope of the intervention is the preservation of cultural heritage. [ABSTRACT FROM AUTHOR]

The study of the seismic response of long bridges under non-uniform seismic excitation date back to the early 80 s. So far, many methods have been developed to estimate the bridge responses under such excitation. Eurocode-8 is considered the first seismic design code that provided a simplified method for linear seismic analysis of long bridges under non-uniform seismic excitation. In this method, earthquake ground motion at each bridge support is decomposed into uniform and relative excitations. Any desired elastic response quantity of bridge for each input is obtained and results are combined using the SRSS combination rule. In this paper, it is shown that the SRSS method leads to very conservative and unrealistic responses. An alternative combination rule is then recommended for response estimation, and random vibration analysis is used to calculate the correlation coefficient between the two mentioned responses. Efficiency evaluation of the proposed method is investigated by Monte Carlo simulation results of nine long bridges with different geometrical and dynamic characteristics. Two simplified mathematical bridge models for longitudinal and transverse directions are developed. Then, a simple mathematical formula for the correlation coefficient is extracted, and its accuracy and performance are evaluated. Finally, it is concluded that the proposed formula is relatively accurate and appears in acceptable results. [ABSTRACT FROM AUTHOR]

Recent Italian earthquakes have shown the seismic vulnerability of many typical historical masonry churches characterized by one nave and wooden roofs. Under transverse earthquake, the nave transverse response of this kind of churches can be influenced by the geometrical and material features. To increase the seismic performance, strengthening interventions aimed to pursue the global box-behavior by the realization of dissipative roof-structure represent a valid strategy, especially to avoid out-of-plane mechanisms. In this way, the roof structure must be able to represent a tool for the damped rocking of the perimeter walls. Cross-laminated timber (CLT) panels with calibrated metal connections have been recently adopted in experimental tests as a valid solution to obtain a roof-diaphragm with ductile behavior, satisfying the conservative restoration criteria at the same time. In this paper, after a description of the numerical approach for the damped rocking mechanism for one nave configuration church, the effectiveness of different CLT based roof-diaphragms in the nave transverse response is investigated for four historical churches. The seismic responses are performed by comparative dynamic nonlinear analyses and the results are shown in terms of displacements and shear actions transferred to the façade. The influence of the geometrical features of the churches on the nave transversal response is deepened by sensitivity analyses with the aim to predict the displacements and shear variations under the same earthquake excitation. [ABSTRACT FROM AUTHOR]

An investigation on seismic response characteristics and modal parameters of a cable-stayed bridge with movable bearings using vibration records obtained from a seismic monitoring system is presented in this paper. The object of this study is the Tokachi cable-stayed bridge, a single plane prestressed cable-stayed bridge that is equipped with moveable spherical frictional plate (SFP). The bridge seismic responses subjected to various levels of earthquake including the 2003 Tokachi Great earthquake were obtained from a permanent seismic monitoring system. The bridge dynamic characteristics that include frequency and damping were estimated by both the time-invariant and time-variant recursive subspace identification methods. The identification results reveal that damping ratios of the low order modes estimated during the largest earthquake can reach more than 10% of the critical damping, which is higher than what usually assumed in the seismic design code. Supplementary damping caused by friction force at the movable SFP bearings was identified as the main source of the large damping, and it was quantified by a modal-based inverse analysis using the sparse regularization method. Results of the analyses confirm the influence of moveable SFP bearings performance with its Coulomb-friction type stick–slip behavior on the dynamic characteristics of the bridge. The bearings remain stuck at smaller excitation causing higher stiffness of the structure and slip during a larger excitation resulting in stiffness reduction. The sliding process induces friction force between contacting surfaces of the SFP bearings which results in the increase of damping as the excitation level increases. The damping, however, does not increase continuously, but becomes steadier after a certain level of excitation. [ABSTRACT FROM AUTHOR]

Despite significant research advances on the seismic response analysis, there is still an urgent need for validation of numerical simulation methods for prediction of earthquake response and damage. In this respect, seismic monitoring networks and proper modelling can further support validation studies, allowing more realistic simulations of what earthquakes can produce. This paper discusses the seismic response of the "Pietro Capuzi" school in Visso, a village located in the Marche region (Italy) that was severely damaged by the 2016–2017 Central Italy earthquake sequence. The school was a two-story masonry structure founded on simple enlargements of its load-bearing walls, partially embedded in the alluvial loose soils of the Nera river. The structure was monitored as a strategic building by the Italian Seismic Observatory of Structures (OSS), which provided acceleration records under both ambient noise and the three mainshocks of the seismic sequence. The evolution of the damage pattern following each one of the three mainshocks was provided by on-site survey integrated by OSS data. Data on the dynamic soil properties was available from the seismic microzonation study of the Visso village and proved useful in the development of a reliable geotechnical model of the subsoil. The equivalent frame (EF) approach was adopted to simulate the nonlinear response of the school building through both fixed-base and compliant-base models, to assess the likely influence of soil–structure interaction on the building performance. The ambient noise records allowed for an accurate calibration of the soil–structure model. The seismic response of the masonry building to the whole sequence of the three mainshocks was then simulated by nonlinear time history analyses by using the horizontal accelerations recorded at the underground floor as input motions. Numerical results are validated against the evidence on structural response in terms of both incremental damage and global shear force–displacement relationships. The comparisons are satisfactory, corroborating the reliability of the compliant-base approach as applied to the EF model and its computational efficiency to simulate the soil–foundation–structure interaction in the case of masonry buildings. [ABSTRACT FROM AUTHOR]

This paper sets out to explore the different ways in which communities deal with earthquakes. As is well known, the ability to recover from a damaging earthquake varies greatly across the world. The events of 2010 were of course a striking reminder of this, when the death toll from the Haïti earthquake was at least 100,000; in the very different conditions of Chile, a much larger event the same year killed just 525 people. In a narrow sense, much of the difference can be explained in terms of the engineering properties of the physical infrastructure affected; the better it has been designed and constructed to withstand strong ground shaking, the greater the chance that the community affected has of recovering quickly. However, the central thesis of this paper is that the ability of a community to deal with earthquakes involves much more than just technical factors. Seismically resilient buildings and other infrastructure will only be in place when an earthquake strikes if there has been a willingness and ability to devote the necessary resources to building them. Moreover, taking prior steps to limit physical damage is only one part of the process for dealing with earthquakes; providing for immediate post-earthquake needs and for the longer term rebuilding of communities is also important. To pursue these issues further, and how they might affect engineers, I visited four widely differing regions of high seismicity. During this study tour, I examined the societal context in which seismic engineers operate and talked to many people involved in earthquake protection and response. The intention was to identify the ways in which the ability of communities to deal with earthquakes depend on societal factors such as economics, politics and more general cultural dimensions. Based on these investigations, I believe that seismic engineers can contribute more effectively to ensuring successful outcomes after an earthquake strikes if fully aware of these societal factors. We need to look beyond our narrow technical field of providing earthquake resistant facilities and widen our vision to consider the complex systems, both ‘hard’ and ‘soft’, in which those facilities will operate. E. F. Schumacher’s famous book (Schumacher 1973) ‘Small is beautiful’ has the subtitle ‘the study of economics as if people mattered’. I believe that seismic engineering should be practised ‘as if people mattered’. [ABSTRACT FROM AUTHOR]

The companion paper by Rota and Rosti (Bull Earthq Eng, 2017) illustrates a methodology for comparing PSH results with historical macroseismic observations at different scales, in terms of mean damage. This paper presents examples of application of the methodology, at the different considered scales, to the South-East quarter of France. This moderate seismicity region is characterised by a long history of civilization, which makes macroseismic observations available for a long time span, although they are highly approximated measures of the seismic action and they are affected by significant uncertainties. The first scale of application presented is at a single site, i.e. the city of Annecy. This example shows that, despite the seismic history of this city is characterised by a significant number of macroseismic observations spanning over a long time period, they mostly consist of very low intensity values and hence the comparison at a single site is not very meaningful. Therefore, the comparison is carried out on a set of seven aggregated sites, well distributed in the region of interest, providing interesting results and suggesting the opportunity of extending the comparison at an even larger scale. The comparison at the regional scale also allows some interesting observations, although it is obviously able to only provide general (average) indications on the PSH results. These comparisons were aimed at showing the applicability of the proposed methodology, pointing out advantages and drawbacks of the different application scales. [ABSTRACT FROM AUTHOR]

Site effects in consequence of the 2016–2018 Central Italy seismic sequence "marked the fate" of many villages located close to the epicenters along the Apennine chain. Pescara del Tronto, a small settlement located on a mountain slope in the municipality of Arquata del Tronto, (AP) is very representative of such territories since, early after the onset of the seismic sequence, suffered very impressive site effects, including a large seismically-induced debris flow and a high number of small volume landslides. This paper describes the main results of the scientific activities carried out by the authors in this locality in the framework of the unprecedented large-scale Seismic Microzonation project funded by Italian Government in Central Italy for 138 territories. Through an intense field activity, the geological and geomorphologic setting of the study area were revised and updated, including a landslide susceptibility assessment that helped the Italian Department of Civil Protection in the emergency management for temporary housing and, later on, was included in the 3rd Level Seismic Microzonation study implemented by authors while the seismic sequence was still ongoing. A very detailed and reliable subsoil model for this municipality was defined, despite difficulties faced in performing direct and indirect investigations due to the safety restrictions for many areas. The Local Seismic Site response was finally assessed for this locality and the results discussed. A key role in the occurrence of strong site effects into Pescara del Tronto has been played by quaternary deposits having an unexpected heterogeneity under the old village. [ABSTRACT FROM AUTHOR]

According to the United Nations Office for Disaster Risk Reduction cities must take measures to anticipate disasters and mitigate their impact, protecting homes and cultural heritage, minimizing losses due to earthquakes and other threats. After the recent earthquakes in historical city centres, the evaluation of the seismic risk, even in regions of low or moderate seismicity, is imperative, being damage assessment and loss estimation essential for its reduction. In this paper the seismic risk analysis of the residential buildings in the Ciutat Vella District in Valencia, with great historical and architectural value, is presented. The vulnerability of Ciutat Vella has been assessed with the Vulnerability Index Method establishing the seismic quality of the residential buildings according to their structural typology, conservation status, age and geometry; identifying the most vulnerable buildings. Damage probability matrices have been obtained for the deterministic and probabilistic earthquake scenarios, estimating for each of them, the seismic risk in terms of direct social and economic losses, mapping the results using a GIS system tool. Results confirm that the vulnerability of the building stock in Ciutat Vella is high being the seismic risk significant. In the event of an earthquake, many residential buildings included in the Catalogue of Listed Buildings of the Special Protection Plan of Ciutat Vella will be damaged. The detailed analysis of the most vulnerable buildings will provide, in future research works, criteria for intervention to enhance their structural seismic response, safeguarding the architectural heritage and contributing to the reduction of human and material losses. [ABSTRACT FROM AUTHOR]

According to most of current design standards, the need for high strength and ductility of reinforced concrete frame structures is accomplished utilizing a high amount of transverse reinforcement in beam-column joints. Reinforcement congestion can be overcome by means of Fiber Reinforced Concrete and High Performance Fiber Reinforced Concrete, which are known to improve the structural performance of single structural members or beam-column joints. Through an extended numerical simulation, this paper elaborates the overall benefits of using fiber reinforced concrete materials in critical regions to the seismic behaviour of regular reinforced concrete frame structures. An extensive number of non-linear static and dynamic analyses with distributed plasticity and fibre sections are performed to compare the behaviour of simple reinforced concrete and mixed reinforced concrete/fiber reinforced concrete frames in terms of total base shear and fragility curves and failure mechanisms. Even if execution and technological aspects are beyond the scope of the present work, the use of fiber reinforced concretes in critical regions of mixed frames seems to improve the structural performance of reinforced concrete frames at a global level. [ABSTRACT FROM AUTHOR]

This paper describes how the earthquake parameters of historical earthquakes have been determined in Europe from macroseismic data by means of the so-called 'Boxer' method, in the frame of the European Commission 2009-2012 Project SHARE (Seismic Hazard Harmonization in Europe). The problems related to the assessment of magnitude are described with more detail; the methodological issues are developed with special reference to the 'stable continental region'. The paper first describes how the coefficients of the Boxer method are determined in five tectonic regions of the European area from the relevant calibration data sets, and discusses the problems dealt with while performing this task. Then it describes how the results have been checked against data different from those used in the previous phase. Finally, the application of the new coefficients to nearly a thousand of European earthquakes before 1900 is described. Stressing that, for the first time in Europe, homogeneous results have been obtained at such a large scale, the final part of the paper is devoted to analyse such results, with special reference to the general trends and to some case-histories. [ABSTRACT FROM AUTHOR]

The seismic Performance-Based Assessment (PBA) of monumental buildings requires to consider safety and conservation objectives, including also the possible presence of artistic assets. In order to face these issues, the case study of the Great Mosque of Algiers is analysed in this paper: in fact, besides to be one of the remaining Almoradiv architecture and the oldest mosque of the city, it is also characterized by the presence of a mihrâb, a decorated arched niche that represents an interesting artistic asset to be included in the PBA. Within this context, particular attention has been paid to the choice of the most reliable modelling strategy for the application of the displacement approach in the PBA procedure, as a function of different possible seismic behaviours. In the case of Great Mosque both the current state of the building and a virtual strengthened condition are analysed. It is worth noting that, while in the current state the seismic behaviour of the asset is well described by a set of macroelements that may be analysed independently (through 2D models), in the second case the strengthening intervention leads to the adoption of a 3D global model (indeed, the roof bracing promotes a 'box-type' behaviour). In the paper, the integrate use of three different modelling strategies of different complexity is discussed: the finite element model, the equivalent frame approach and the macro-block model. The results of nonlinear analyses performed (static and kinematic) constitute the main tool to interpret the seismic response of the asset, perform the PBA and address the choice on the rehabilitation decisions. These latter in this case are mainly affected by the occurrence of too high deformations in local portions of the building, including that in which the artistic asset is located. [ABSTRACT FROM AUTHOR]

The M = 7.8 Muisne event of April 16, 2016 occurred on Saturday at 18:58:37 local time off-shore of the west coast of northern Ecuador. Several cities in the province of Manabí were directly affected and a state of emergency was declared in six provinces encompassing a total area of 70,000 km. The building stock was severely damaged. 80% of the buildings were destroyed in the city of Pedernales, while several multi-storey reinforced concrete structures totally collapsed in the cities of Manta and Portoviejo. Field observations on the seismic performance of reinforced concrete buildings inspected by the authors are presented in this paper. Also, numerical results from three-dimensional pushover analysis of a representative case study building are discussed. The effect of corrosion and masonry infills, which played a key role in the observed damage, was directly taken into account in the analytical model. [ABSTRACT FROM AUTHOR]

In this paper, we separate the residuals of ground motion prediction equations into different components, calculating the repeatable site-specific ( $$\delta S2S_{s}$$ ), location-specific ( $$\delta L2L_{r}$$ ) and path-specific ( $$\delta P2P_{er}$$ ) correction for the median model. In this way, we can reduce the total standard deviation (sigma) of the ground-motion model by Lanzano et al. (Bull Seismol Soc Am 106(1):73-92, 2016), removing these components and overcome the ergodic assumption. These repeatable terms are empirically estimated using a dataset composed by acceleration waveforms of Italian events mainly occurred in the Po plain and Eastern Alps (Northern Italy), in the time interval 1976-2015. The analysis is carried out on 2241 recordings, from 88 shallow earthquakes recorded by 168 sites. A local model, specifically tailored for Northern Italy, is used as the reference GMPE, which predicts the geometric mean of the horizontal peak ground accelerations and response spectral ordinates in the period range 0.04-4 s. Because most of the propagation paths sampled only once, the path-specific components and the resulting aleatory variability are also calculated from the spatial correlation of residuals, following the approach of Lin et al. (Bull Seismol Soc Am 101(5):2281-2295, 2011). We find a significant reduction of the overall ground motion variability to an extent comparable to what observed from previous studies on empirical and simulated datasets. The estimated median corrections and variance components can be used in probabilistic seismic hazard assessment for a single site and a single path in Northern Italy. As an example, we compute the hazard curves at some sites by means of three different approaches (ergodic, partially non-ergodic and full non-ergodic), in order to quantify the impact of relaxing the ergodic assumption. [ABSTRACT FROM AUTHOR]

This paper presents a reassessment of the seismic intensity estimated for the 2011 Lorca (southeastern Spain) earthquake based on detailed vulnerability data and its comparison with the observed damage. Building and urban data are gathered in selected areas during a field campaign and are completed with office work. The significance of vulnerability modifiers in the final vulnerability distribution is analyzed, and their relation with observed damage trends is explored. A direct application of the vulnerability modifiers is not capable of reproducing the observed damage patterns. A significant increase of vulnerability related to the performance of buildings presenting soft story is required to reach a damage distribution consistent with intensity estimates in the study areas. Accordingly, an intensity increase in certain study zones (as compared to other areas of the city of Lorca) is suggested. Although the approach followed in this study is applied in a city of Spain, it can be extrapolated to other areas where detailed vulnerability assessment is feasible and damage data are available. [ABSTRACT FROM AUTHOR]

Due to the increased need of storage, larger and higher structures are being built all over the world, thus requiring a more careful evaluation of the mechanical performance of their foundation deposits both in terms of bearing capacity and compressibility behaviour. The design of such structures and their serviceability and stability is largely governed by the effects of the dynamic loading conditions principally because of their significantly elevated risk in seismic prone zones. In this paper, numerical analyses using an advanced constitutive model, able to account for the initial soil structure and its progressive degradation, have been performed to investigate the seismic response of a silo foundation built on structured clays. The proposed analyses involve the use of a fully-coupled finite element approach. For the dynamic simulations, three different input motions have been selected form earthquake databases according to the seismic hazard study of the specific site. The results of the silo dynamic response are illustrated in terms of signal amplification, permanent excess pore water pressures, accumulated displacements and structure induced degradation during and after the seismic loading. The dynamic behaviour of the footing indicates that extreme earthquake events can induce large destructuration in natural clays, leading to ground settlements up to twice the observed ones under static loads, which need to be properly accounted for in the design. This suggests that there are significant advantages in using advanced models which recognise the existence of initial soil structure and its subsequent damage due to the applied dynamic loads. [ABSTRACT FROM AUTHOR]