Search

The surface hydrophobicity of membrane is a key factor in contactor applications where the penetration of liquid into membrane pores has negative effect on the contactor performance. Therefore, different methods have been proposed for surface modification. Blending hydrophobic polymers such as surface modifying macromolecules (SMM) has been investigated in our earlier researches. In this study, the effect of polyvinylidene fluoride (PVDF) blending on the surface and bulk morphology of polyetherimide (PEI) hollow fiber membrane and its performance in membrane gas absorption process was studied. It was found that the pore size increased from 112 nm to 210 nm from the neat PEI membrane to the PEI membrane spun from the solution blended with 0.25 wt% PVDF. At the same time, the contact angle increased from 78.3 and 84.3. Furthermore, the absorption flux of PVDF blended membrane enhanced by 13% compared to the neat PEI membrane. [ABSTRACT FROM AUTHOR]

A novel method, Thermally Modified Non-Solvent Induced Phase Separation (T-NIPS) has been developed to fabricate translucent hollow fiber (THF) photocatalytic membrane for membrane's photodegradation efficiency enhancement. The process involves two-step temperature treatment that attacks crystalline property of polyvinylidene fluoride (PVDF). Graphitic carbon nitride in a modified morphological structure (hollow nanofiber) was used as photocatalyst to investigate the effect of translucency on membrane's photodegradation efficiency. UV-Vis analysis coupled with FTIR highlighted different crystalline phase appearance and membrane's translucency. The membranes showed high translucency, ranging from 60.0% to 93.9%, with THF-PVDF/PVP-GCN (2.0) exhibiting the highest. The filtration experiment showed that membrane with GCN photocatalyst had high PWF (1200 L/m2h) and rejection (90%) OPW compared to neat THF-PVDFs. In suspended mode, GCN demonstrated an impressive photodegradation efficiency of 99.98%. When immobilized in opaque PVDF membrane, the photodegradation has decreased substantially to 49.40%. However, when immobilized in a translucent PVDF membrane, the photodegradation efficiency of HN-GCN significantly improved compared to the opaque PVDF membrane, reaching 95%. Translucent membrane was subjected to five cycle regeneration test and showed 90% recovery even after the fifth cycle. The 10% reduction in the recovery was investigated using FESEM analysis revealed that there is a cake layer formation on the membrane surface. Therefore, this study proved that translucency of membrane has significant effect on immobilized photocatalyst's photocatalytic efficiency. [Display omitted] • Novel T-NIPS method to produce THFM is developed. • HN-GCN successfully immobilized in THFM. • HN-GCN immobilized THFM showed increased degradation efficiency of OPW. [ABSTRACT FROM AUTHOR]

This study involves the preparation of a double-skinned thin film composite (TFC) and thin film nanocomposite (TFN) hollow fiber (HF) membrane for forward osmosis (FO) applications. The porous substrate consisted of a Polyvinyl chloride (PVC) / Polycarbonate (PC) blend HF membrane. Interfacial polymerization (IP) was then applied to coat a polyamide (PA) layer on the lumen surface and the porous substrate's outer surface. In addition, the impact of the outer PA active layer and the addition of nanoparticles to the outer selective layer on the FO flux and internal concentration polarization (ICP) were studied. By adding the second active layer to the substrate, water flux, reverse salt flux and ICP decreased. Also, the decline of water flux decreased over time due to the fouling agent. To compensate for the decrease in water flux in the double-skinned membrane, graphene oxide (GO) nanoparticles with 0.05% and 0.1%wt were added to the outer active layer. Addition of 0.1%wt graphene oxide nanoparticle to the outer active layer can help to improve water flux about 78% without spoiling the reverse salt flux. Moreover, the performance of double-skinned membranes against osmotic dilution process for oily wastewater treatment was investigated. The findings of this study demonstrated that the novel double-skinned TFN HF membrane exhibited high FO performance with low ICP and fouling. [Display omitted] • Inclusion of a second active layer without reducing the reverse salt flux and fouling. • To improve fouling resistance of membrane, GO was added to second active layer. • By adding GO to outer active layer, reverse salt flux and fouling was reduced. • The Hermia model showed intermediate blocking in neat membrane. • The predominant fouling in double-skin membranes is cake formation. [ABSTRACT FROM AUTHOR]

The aim of this work was to investigate the effects of heat treatment applying hot air at different temperatures and durations on the morphology and the performance of polyetherimide (PEI) hollow fiber membrane contactors for CO 2 separation. The membranes were fabricated via a wet spinning into non solvent bath technique. Then, the membranes were heat treated by exposing them at 80,120 and 160 °C for all time intervals of 5, 15 and 30 min under a hot air atmosphere. To study the influence of the hot air on the membranes structural parameters and the performance of the membranes they were characterized by: gas permeation test, membrane overall porosity measurement, critical entry pressure of water (CEPw) and gas absorption via a membrane contacting process. The experimental results revealed that, the greatest effect on the membranes structure was observed in the shortest time duration and the lowest temperature i.e. 5 min and 80 °C, which exhibited a pore size of 49 (nm), a maximum effective surface porosity of 26.8 (1/m) and a CEPw of 3.4 bar. Also, for all the time periods and the temperatures tested, the density of the fibers reduced and the CEPws along with the overall porosities increased. In conclusion, applying heat treatment technique on PEI hollow fiber membranes is a simple and easy approach to improve the performance of hollow fiber membrane contactors for CO 2 removal. [ABSTRACT FROM AUTHOR]