Search

As electron transport layers (ETLs) in perovskite solar cells (PSCs), tin oxide (SnO2) possess high carrier mobilities with appropriate energy band alignment and high optical transmittance. Herein, SnO2 ETLs were fabricated by intermediate‐controlled chemical bath deposition (IC‐CBD) at ultralow temperature, where the chelating agent effectively altered the nucleation and growth process. Compared with conventional CBD, SnO2 ETLs fabricated by IC‐CBD had lower defects, smooth surface, good crystallinity, and remarkable interfacial contact with perovskite, resulting in good quality of perovskite, high photovoltaic performance (23.17 %), and enhanced stability of devices. [ABSTRACT FROM AUTHOR]

A high‐performing inverted perovskite solar cell (PSC) always relies on the hole transporting layer (HTL) quality and its interfaces. This work investigates the impact of La incorporation within the NiOx matrix for defects passivation, thus leading to high charge extraction ability and stability without compromising its power conversion efficiency. In the presence of La, the La–NiOx quality is clearly improved; without the formation of pinholes. In addition, the inclusion of La alters the energy band alignment; consequently, enhancing the hole transportation and widening the Voc (>1 V), as compared to the pristine NiOx. The beneficial effect of La was further revealed through the photoluminescence measurement and density of states (DOS) analysis, in which trap states are passivated by La. More importantly, the perovskite solar cell, with La–NiOx as the HTL, exhibits 21 % enhancement in efficiency and a remarkable stability that is greater than that of pristine NiOx. This also unlocks an opportunity for commercialization. Inversion therapy: A high‐performing inverted perovskite solar cell (PSC) always relies on the hole transporting layer (HTL) quality and its interfaces. This study concerns the impact of lanthanum incorporation within the NiOx matrix for high conductivity, charge extraction ability, and stability without compromising its power conversion efficiency. [ABSTRACT FROM AUTHOR]

Trap states at the interface or in bulk perovskite materials critically influence perovskite solar cells performance and long‐term stability. Here, a strategy for efficiently passivating charge traps and mitigating interfacial recombination by SnO2 surface sulfur functionalization is reported, which utilizes xanthate decomposition on the SnO2 surface at low temperature. The results show that functionalized sulfur atoms can coordinate with under‐coordinated Pb2+ ions near the interface. After device fabrication under more than 60 % humidity in ambient air, the efficiency of methylammonium lead iodide (MAPbI3) perovskite solar cells based on sulfur‐functionalized SnO2 increased from 16.56 % to 18.41 % with suppressed hysteresis, which resulted from the accelerated interfacial charge transport kinetics and decreased traps in bulk perovskite by interfacial sulfur functionalization. Additionally, thermally stimulated current studies show the decreased trap density in the shallow trap area after interfacial sulfur functionalization. The interfacial sulfur functionalized solar cells without sealing also exhibited considerable retardation of solar cell degradation with only 10 % degradation after 70 days air storage. This work demonstrates a facile sulfur functionalization strategy by using xanthate decomposition on SnO2 surfaces to obtain highly efficient perovskite solar cells. Inorganic sulfur functionalization has been realized through xanthate annealing on a SnO2 substrate, facilitating electron transport and reducing trap density at the shallow area. The efficiency of the resulting perovskite device was increased significantly with enhanced long‐term stability upon interfacial sulfur functionalization. This method is a simple and highly efficient means of interfacial functionalization with enhanced stability by using inorganic atoms. [ABSTRACT FROM AUTHOR]

Abstract: Perovskite solar cells have attracted considerable attention owing to their easy and low‐cost solution manufacturing process with high power conversion efficiency. However, the fabrication process is usually performed inside a glovebox to avoid moisture, as organometallic halide perovskites are easily dissolved in water. In this study, we propose a one‐step fabrication of high‐quality MAPbI3 perovskite films in around 50 % relative humidity (RH) humid ambient air by using diethyl ether as an antisolvent and methanol as an additive into this antisolvent. Because of the presence of methanol, the water molecules can be efficiently removed from the gaps of the perovskite precursors and the perovskite film formation can be slightly controlled, leading to pinhole‐free and low roughness films. Concurrently, methanol can be used to tune the DMSO ratio in the intermediate perovskite phase to regulate perovskite formation. Planar solar cells fabricated by using this method exhibited the best efficiency of 16.4 % with a reduced current density–voltage hysteresis. This efficiency value is approximately 160 % higher than the devices fabrication by using only diethyl ether treatment. From the impedance measurement, it is also found that the recombination reaction is suppressed when the device is prepared with methanol additive in the antisolvent. This method presents a new path for controlling the growth and morphology of perovskite films in humid climates and laboratories with uncontrolled environments. [ABSTRACT FROM AUTHOR]

Mesoporous-graphitic-carbon-supported HfO2 (HfO2-MGC) nanohybrids were synthesized by using a soft-template route. Characterization and a systematic investigation of the catalytic properties, stability, and catalytic mechanism were performed for HfO2-MGC counter electrodes (CEs) in dye-sensitized solar cells (DSSCs). The new HfO2-MGC as a CE in DSSCs showed a surprisingly high efficiency of 7.75 % for the triiodide/iodide redox couple and 3.69 % for the disulfide/thiolate redox couple, greater than the Pt electrode in the corresponding electrolyte system, which opens up a possibility for its practical application. [ABSTRACT FROM AUTHOR]

As electron transport layers (ETLs) in perovskite solar cells (PSCs), tin oxide (SnO 2 ) possess high carrier mobilities with appropriate energy band alignment and high optical transmittance. Herein, SnO 2 ETLs were fabricated by intermediate-controlled chemical bath deposition (IC-CBD) at ultralow temperature, where the chelating agent effectively altered the nucleation and growth process. Compared with conventional CBD, SnO 2 ETLs fabricated by IC-CBD had lower defects, smooth surface, good crystallinity, and remarkable interfacial contact with perovskite, resulting in good quality of perovskite, high photovoltaic performance (23.17 %), and enhanced stability of devices., (© 2023 Wiley-VCH GmbH.)

Perovskite solar cells have attracted considerable attention owing to their easy and low-cost solution manufacturing process with high power conversion efficiency. However, the fabrication process is usually performed inside a glovebox to avoid moisture, as organometallic halide perovskites are easily dissolved in water. In this study, we propose a one-step fabrication of high-quality MAPbI 3 perovskite films in around 50 % relative humidity (RH) humid ambient air by using diethyl ether as an antisolvent and methanol as an additive into this antisolvent. Because of the presence of methanol, the water molecules can be efficiently removed from the gaps of the perovskite precursors and the perovskite film formation can be slightly controlled, leading to pinhole-free and low roughness films. Concurrently, methanol can be used to tune the DMSO ratio in the intermediate perovskite phase to regulate perovskite formation. Planar solar cells fabricated by using this method exhibited the best efficiency of 16.4 % with a reduced current density-voltage hysteresis. This efficiency value is approximately 160 % higher than the devices fabrication by using only diethyl ether treatment. From the impedance measurement, it is also found that the recombination reaction is suppressed when the device is prepared with methanol additive in the antisolvent. This method presents a new path for controlling the growth and morphology of perovskite films in humid climates and laboratories with uncontrolled environments., (© 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.)

Mesoporous-graphitic-carbon-supported HfO2 (HfO2 -MGC) nanohybrids were synthesized by using a soft-template route. Characterization and a systematic investigation of the catalytic properties, stability, and catalytic mechanism were performed for HfO2 -MGC counter electrodes (CEs) in dye-sensitized solar cells (DSSCs). The new HfO2 -MGC as a CE in DSSCs showed a surprisingly high efficiency of 7.75 % for the triiodide/iodide redox couple and 3.69 % for the disulfide/thiolate redox couple, greater than the Pt electrode in the corresponding electrolyte system, which opens up a possibility for its practical application., (Copyright © 2014 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.)