Search

The purpose of this study was to investigate the clinical application possibility of pure titanium konus telescope crowns fabricated using a CAD/CAM system. For the CAD/CAM system, Dental Cadim (Advance Co.) was used. For the material, exclusive pure titanium block for this system was used in this experiment. Two types of experimental dies with different heights assumed the konus inner crown and three types of konus outer crowns with different gap widths at the occlusal part were prepared. The outer crown was seated on the inner crown die, and a load was applied perpendicularly to the upper surface of the outer crown for 10 seconds. Pullout test was performed at a crosshead speed of 5 mm/min, and the retentive force was measured. With increase in the height of the inner crown die and the applied load, the retentive force of konus telescope crown increased. Similarly, as the gap width at the occlusal part between the inner crown die and outer crown increased, the retentive force of konus telescope crown also increased.

The objective of this study was to evaluate the effects of triethylene glycol (TEG) and triethylene glycol monomethacrylate (TEGMA) solutions as dentin primers on dentin bonding. To this end, wall-to-wall polymerization contraction gap width of a resin composite in a cylindrical dentin cavity and shear bond strength to a flat dentin surface were measured. Dentin was pretreated with an experimental dentin bonding system - consisting of 0.5 M ethylenediaminetetraacetic acid conditioner, TEG or TEGMA primer, and Clearfil Photo Bond bonding agent - prior to resin composite filling. When the cavity was primed with an aqueous solution of 35 vol% TEG, 35 or 45 vol% TEGMA for a few seconds, contraction gap formation was prevented completely. Then, among these three gap-free groups, there were no significant differences in shear bond strength. It was thus shown that both TEG and TEGMA were highly effective dentin primers, completely preventing contraction gap formation even when they were applied for only a few seconds.

To evaluate the effect of a dentin adhesive on sclerotic dentin, contraction gap width and shear bond strength were measured. Dentin cavity wall was pretreated with an experimental dentin bonding system with and without a dentin primer, or with a commercial dentin bonding system. In the experimental dentin bonding groups, contraction gap width of sclerotic dentin was significantly smaller than that of sound dentin when the cavity was not primed with glyceryl monomethacrylate. For each individual tooth, the correlation between contraction gap width and shear bond strength was insignificant. In conclusion, the bonding efficacy of dentin bonding systems to sclerotic dentin was superior to that of sound dentin. Further, it was determined that it was impossible to detect the interaction between the polymerization contraction stress of resin composites and the efficacy of dentin adhesives by measuring bond strength.

The dentin cavity adaptation and setting characteristics of four commercial compomers were evaluated by measuring the wall-to-wall contraction gap width in the cylindrical dentin cavity and measuring the compressive strength for a maximum of 14 days after setting. The dentin cavity wall was pretreated by the dentin adhesives according to each manufacturer's instructions or the experimental contraction gap-free dentin bonding system. Complete marginal integrity was obtained in only one compomer and two resin composites which were combined with the experimental dentin bonding system. The compressive strength of two resin composites and two compomers ten minutes after setting was comparable to that after 14 days which indicated that the compomers exhibited setting characteristics as rapidly as the resin composite. It was concluded that a high efficacy dentin bonding system is required for commercial compomers to prevent gap formation during irradiation caused by the rapid setting shrinkage.

The effects of 2-hydroxyethyl methacrylate (2-HEMA) both in the primer and in the commercial dentin bonding agent on the efficacy of the dentin bonding system was evaluated by measuring the polymerization contraction gap width of a commercial resin composite restored in a cylindrical dentin cavity prepared in an extracted human molar. Contraction gap formation was prevented in the group of the EDTA-conditioning followed by glyceryl mono-methacrylate, ethylene glycol and 1, 6-hexanediol priming regardless of the 2-HEMA content in the dentin bonding agent containing 10-methacryloxydecyl dihydrogen phosphate. However, gap formation could not be prevented completely by the 2-HEMA priming. Therefore, it was possible to conclude that 2-HEMA was neither essential in the primer nor in the dentin bonding agent because of its low bonding efficacy and the resulting side effects on skin tissue as a delayed allergic reaction.

The aim of this study was to investigate the diffusion of red-stained experimental GM primer and blue-stained dentin bonding agent into EDTA-conditioned dentin and the effect of GM priming on contraction gap formation. After GM priming at 0, 35, 70, or 100 vol%, marginal adaptation was evaluated by measuring the wall-to-wall contraction gap width of a light-activated resin composite (Palfique Estelite, Tokuyama Dental, Japan) mediated with a commercial dentin bonding agent (Clearfil Photo Bond, Kuraray Medical, Japan). Contraction gap formation was completely prevented when treated with 35 vol% GM primer. Moreover, after treatment with 35 vol% GM, the red and blue dyes of stained GM primer and dentin bonding agent diffused up to a depth of 40 µm into the dentin surface. The diffusion of primer and bonding agent into EDTA-conditioned dentin was essential for bonding efficacy although SEM observation revealed an absence of hybrid layer formation.

The bonding efficacy of sclerotic dentin was determined by measuring the polymerization contraction gap width of a commercial light-activated resin composite in a cervical defect and by measuring the micro-Vicker's hardness at the dentin adhesive surface; morphological characteristics were observed using a scanning electron microscope in extracted human incisors and premolars. Contraction gap formation was completely prevented when the cavity wall was primed with 35 vol% glyceryl mono-methacrylate solution after 0.5 mol/L EDTA conditioning. The contraction gap width was significantly decreased when the resin composite was filled into the sclerotic dentin cavity even when priming was omitted. These results suggest that the sclerotic dentin, which is frequently observed in cervical defects, should be preserved as a substrate because it exhibits an effect of dentin priming and is suitable for bonding.

The effectiveness of newly developed commercial dentin bonding systems (SB, MB II and KB) was evaluated by measuring the contraction gap width of a resin composite restored into a cylindrical dentin cavity prepared in an extracted human molar and by measuring the tensile bond strength to the flat dentin surface. In addition, calcium loss during dentin conditioning was analyzed using electron microanalyses. An experimental dentin bonding system composed of EDTA conditioning, GM solution priming and a bonding agent containing 10-MDP was employed as a control in which it was presumed that contraction gap formation was prevented completely. However, gap formation was observed using the three commercial simplified dentin bonding systems. SEM observation showed that the gap was formed between the resin composite and the top surface of the dentin cavity wall indicating that the fracture occurred at the adhesive interface, but never inside the dentin nor inside the resin composite.

The bonding ability of bonding agents and composites from three manufacturers, which have both chemically and visible light activated systems, were evaluated by measuring the contraction gap width between the material and the cavity wall in a dentin cavity.The visible light cured composites were inferior to the same manufacturer's chemically cured composites in marginal adaptation to a cylindrical dentin cavity. However, the adaptation of composites to the cavity wall was improved when the light cured bonding agent was polymerized prior to the placement of chemically cured composite resin.

The cavity adaptation of marketed composite resins was evaluated by measuring the contraction gap width in a cylindrical dentin cavity. Cavity walls were cleaned with neutralized 0.5 M EDTA and treated with an aqueous solution of 35% HEMA and a dentin bonding agent. The inorganic filler content was measured by weighing specimens before and after burning. When the composite which contained an inorganic component of less than 75 wt% was employed, a relatively low contraction value of less than 0.09% was obtained. On the other hand, for the composite with an inorganic component of more than 75 wt%, the gap values varied from 0.01 to 0.43%. However, using regression analysis, no statistically significant correlation was observed between the wall-to-wall polymerization contraction and the inorganic filler content.