Search

This paper presents a mathematical analysis of how energy return in grid-connected single-phase photovoltaic systems affects the sizing of passive components. Energy return affects the size of the link capacitor, making it larger than reported in the literature. One of the main points of this article is that an inverter connected to the grid using a DC–DC converter with an appropriate link capacitor is analyzed. The energy return is caused by the value (in Henry units) of the L-filter, which is also analyzed in this paper. The analysis shows that there is a link between the value of the L-filter and the voltage of the DC bus. The analysis assumes two conditions: (1) the DC bus voltage is always higher than the peak value of the grid sinusoidal voltage, and (2) there is a unity power factor at the connection point between the grid and the L-filter. To operate in an open loop, a compensation phase angle is calculated and introduced in the single-phase inverter modulation; this phase angle compensates the phase shift caused by the L-filter, avoiding the use of a phase-locked-loop (PLL) control system. The L-filter ripple current is evaluated by Fourier analysis, and the DC bus ripple voltage is evaluated by considering the energy returned to the link capacitor. The results of the analyses are compared with existing methods reported in the literature. The results also show that, to minimize the value of the L-filter, the DC voltage must be almost equal to the maximum voltage of the grid. Equations to assess the value of the DC-link capacitor and the L-filter in function of their ripples are developed. The results were verified with simulations in Simulink and experimentally. [ABSTRACT FROM AUTHOR]

The most common problems with magnetic cores in high-stress applications are changes in their permeability and low saturation flux density, forcing designers to use special nanocrystalline cores, which raises the overall cost of the circuit. This paper evaluates the performance of a low-cost magnetic material composed of unsaturated polyester la mination resin COR61-AA-531EX and 200 mesh iron powder with a grain size of 74 µm, which has magnetic properties of the so-called "soft magnetic composites", which have good magnetic characteristics in high-frequency and high-stress applications. This composite material was used for the elaboration of magnetic cores for the inductors of a resonant converter, which aims to achieve a high power factor, where in this type of application, there are large current and voltage excursions in the magnetic components that vary between high and low frequencies, being a suitable application for testing the inductors with a magnetic core of resin/iron powder. The converter was designed to operate off-resonance at different switching frequencies from 300 kHz to 800 kHz to feed a resistive load with a power output of 19 watts. The operation of the circuit was experimentally validated using a resistive load at the output, validating the theoretical analysis and achieving a power factor above 98%. [ABSTRACT FROM AUTHOR]

This paper presents a survey of the articles published in the period 2013–2021 related to the application of the teaching–learning-based optimization (TLBO), which reproduces the dynamics that occur in a classroom with the teacher and the student. This paper uses the algorithm to optimize some objective functions related to the design in the electronics field. A total of 62 papers were reviewed and some graphs were generated to summarize the most relevant of these articles. These have been classified into five categories based on the areas of electronic engineering, such as power electronics, control, electromagnetism, digital electronics, and analogue electronics. Electronic engineering has been becoming increasingly relevant in world technological development, for example, in electric vehicles or generating electricity from renewable energy sources to counteract the environmental impact that non-renewable sources generate. The TLBO algorithm has attracted the interest of a large number of researchers due to its efficiency, speed, and low initialization parameter requirements. This article is composed of two stages, the first is a summary of the information on electronics, in general, encompassing all its areas, and the second focuses on the algorithm applied to multilevel inverters; for each stage, graphs and tables are shown. [ABSTRACT FROM AUTHOR]

This paper presents a theoretical analysis of a DC-DC flyback converter variant applied in energy harvesting based on thermoelectric generators. The main contribution of the article is the analysis and obtaining the equations of the behavior of the converter with a rearrangement of the elements of the traditional flyback converter in such a way that the converter only processes part of the energy while the other part is delivered directly to the load. This is achieved by connecting the secondary of the flyback in series with the load, and this assembly, in turn, is placed in parallel with the primary and the voltage source. This configuration means that the topology can only be a boost topology; however, there are benefits such as partial power processing (R2P2) and reduced stress on converter components in both voltage and current; all this leads to increase the efficiency. A Low Frequency Averaging Analysis (LFAA) was used to determine the behavior of the proposed circuit, and a simple equivalent circuit to analyze was obtained. In order to validate the theoretical analysis, a circuit was simulated in Spice and implemented in an 18 W prototype. Experimental results showed that the converter has an efficiency of 92.65%. Moreover, the rearranged flyback processed only 56% of the input power. [ABSTRACT FROM AUTHOR]

The cascade multilevel inverters are widely used in industrial manufacturing processes for DC-AC conversion. Therefore, the reliability and efficiency improvement, optimized control, and fault-tolerant strategies are areas of interest for researchers. The fault tolerance strategies applied to cascade multilevel inverters are classified as material redundancy and analytical redundancy. This paper presents the use of the Z-source converter as a fault reconfiguration method applied to a cascade multilevel inverter. On the one hand, the proposed approach has the characteristic of combining the use of material redundancy (modifying the output voltage by changing the Z-source operation), and on the other hand, it has the use of analytical redundancy (modifying the switching sequence of the multilevel inverter, changing from symmetrical to asymmetrical operation mode). This approach has been validated by experimental results of the system under fault-free conditions and employing the Z-source converter as the main fault reconfiguration element. The proposed fault reconfiguration strategy allows the cascaded multilevel inverter to continue to operate even in the presence of a fault by having continuous operation. [ABSTRACT FROM AUTHOR]

The main contribution of this paper is to show a new AC/DC converter based on the rearrangement of the flyback converter. The proposed circuit only manages part of the energy and the rest is delivered directly from the source to the load. Therefore, with the new topology, the efficiency is increased, and the stress of the components is reduced. The rearrangement consist of the secondary of the flyback is placed in parallel with the load, and this arrangement is connected in series with the primary side and the rectified voltage source. The re-arranged flyback is only a reductive topology and with no magnetic isolation. It was studied as a power supply for LEDs. A low frequency averaged analysis (LFAA) was used to determine the behavior of the proposed circuit and an equivalent circuit much easier to analyze was obtained. To validate the theoretical analysis, a design methodology was developed for the re-arranged flyback converter. The designed circuit was implemented in a 10 W prototype. Experimental results showed that the converter has a THDi = 21.7% and a PF = 0.9686. [ABSTRACT FROM AUTHOR]

This paper focuses on the main reasons of low efficiency in a current-fed DC-DC resonant converter applied to photovoltaic (PV) isolated systems, comparing the effects derived by the overlapping time in the gate-signals (gate-source voltage) combining silicon (Si), silicon carbide (SiC), and gallium nitride (GaN)-based power devices. The results show that unidirectional switches (metal–oxide–semiconductor field-effect transistors (MOSFETs) plus diode) present hard switching as a result of the diode preventing the MOSFET capacitance of being discharged. The effectiveness of the converter was verified with a 200-W prototype with an input voltage range of 0–30.3 V, an output voltage of 200 V, and a switching frequency of 200 kHz. The reduction losses by applying GaN versus Si and SiC technologies are 66.49% and 53.57%, respectively. Alternatively, by applying SiC versus Si devices the reduction loss is 27.84%. Finally, according to the results, 60% of losses were caused by the diodes on both switches. [ABSTRACT FROM AUTHOR]