Search

The assessment of highly mature source rocks linked to hydrocarbon generation remains a challenge in oil and gas exploration. However, substantial terrigenous influences and thermal variations have complicated the formation and evolution of source rocks. This study presents an integrated assessment of highly mature source rocks in the Fuxin Basin, based on sedimentological, geochemical, and organic petrological analyses. Two types of oil- and coal-bearing source rocks were deposited in the semi-deep lake and shore–shallow lake facies during the Jiufotang and Shahai periods. The development of source rocks migrated eastward alongside the lacustrine depocenter, influenced by basin evolution related to extensional detachment tectonism. Furthermore, a gradual increase in thermal records was detected from the western to eastern basins. Consequently, thermal decomposition of source rocks in the Jiufotang formation reduced the organic matter (OM) abundance in the central and eastern basins. Meanwhile, OM types of source rocks range from kerogen type-II1/-I to type-II2/-III, with intense hydrogen generation observed from the western to eastern basins. Consequently, the quality and hydrocarbon accumulation of source rocks are influenced by sedimentation and thermal maturity variation. The spatiotemporal variation in mature source rocks enhances the potential for exploring conventional petroleum, coalbed methane, and shale gas across different strata and locations. Our findings illustrate the significance of the sedimentary and thermal effects in characterizing the evolution of highly mature source rocks, which is relevant to determine oil and gas exploration in similar geological settings.

Shale oil yield, movability, and reservoir brittleness are three factors that must be focused on for shale oil exploration and development. The yield and composition of hydrocarbons and mineral composition have changed significantly during diagenesis, affecting the yield and movability of shale oil and the brittleness of the rock. In this study, the source rocks at different depths in the Dongying Sag were subjected to hydrous pyrolysis, and the yield and composition of pyrolyzed hydrocarbons and mineral composition were systematically analyzed. The brittleness index (BEI), weighted average specific surface area (SSAWA), and polarity index (PI) have been established to quantitatively characterize the brittleness and adsorption capacity of rock as well as the mobility of shale oil. The results suggest that diagenetic evolution controls rocks’ brittleness and adsorption capacity by changing their mineral composition. In the low-temperature stage, the mineral transformation is not obvious, and the BEI and SSAWA fluctuate in a small range. In the high-temperature stage, the rapid smectite illitization leads to an increase in the brittleness and a decrease in the adsorption capacity. In addition, the nonpolar components such as saturates and aromatics in the pyrolyzed hydrocarbons gradually increased with the increasing temperature, enhancing the mobility of the shale oil. Based on the three evaluation indexes of BEI, PI, and SSAWA, and combined with the changes in hydrocarbon yields during hydrous pyrolysis, we comparatively analyzed the differences in the mobility and yields of original soluble organic matter as well as pyrolyzed hydrocarbons of the source rocks at different depths. Based on the above results, it can be concluded that the shale in the depth range of 3300–3795 m is a favorable area for shale oil exploration and development in the study area. This work suggests that predicting the sweet spot for shale oil exploration and development requires more attention to the impact of diagenetic evolution on the composition of minerals and hydrocarbons.

Petroleum was the most-consumed energy source in the world during the past century. With the continuous global consumption of conventional oil, shale oil is known as a new growth point in oil production capacity. However, medium–low mature shale oil needs to be exploited after in situ conversion due to the higher viscosity of oil and the lower permeability of shale. This paper summarizes previous studies on the process of kerogen cracking to generate oil and gas, and the development of micropore structures and fractures in organic-rich shale formations during in situ conversion. The results show that the temperature of kerogen cracking to generate oil and gas is generally 300–450 °C during the oil shale in situ conversion process (ICP). In addition, a large number of microscale pores and fractures are formed in oil shale formation, which forms a connecting channel and improves the permeability of the oil shale formation. In addition, the principles and the latest technical scheme of ICP, namely, conduction heating, convection heating, reaction-heat heating, and radiation heating, are introduced in detail. Meanwhile, this paper discusses the influence of the heating mode, formation conditions, the distribution pattern of wells, and catalysts on the energy consumption of ICP technology in the process of oil shale in situ conversion. Lastly, a fine description of the hydrocarbon generation process of the target formation, the development of new and efficient catalysts, and the support of carbon capture and storage in depleted organic-rich shale formations after in situ conversion are important for improving the future engineering efficiency of ICP.

This study focused on Middle Permian Lucaogou Formation saline lake source rocks, utilizing a combination of biomarkers and hydrocarbon generation thermal simulation to analyze their biological compositions, depositional environments, and hydrocarbon generation potential. The Pr/Ph ratio, Ph/nC18 ratio, and Pr/nC17 ratio indicate that the Lucaogou Formation was in a reducing environment during the deposition period, and the lower part of the Lucaogou Formation (P2l1) is more anoxic than the upper part of the Lucaogou Formation (P2l2). The maturity index 20S (%) and ββ (%) reflect that the maturity of organic matter in the P2l1 is slightly higher than that in the P2l2. The G/H index and the ETR index indicate that the stratification of the water column is better during the sedimentary period of Lucaogou Formation and the salinity of the P2l1 is higher than that of the P2l2. The biomarker parameters of nC21−/nC22+, CPI, S/H, and C22T/C21T reflect that the organic matter of the source rocks have a higher abundance of bacteria and algae than higher plants, and the contents of bacteria are more than that of algae. The (7- + 8-MMAs)/Cmax and (C28 + C29 − St)/St parameters indicate that cyanobacteria accounted for a certain proportion of bacteria, and the algae are mainly green algae. The co-evolution of the sedimentary environment and the biological composition reflects the control of the sedimentary paleoenvironment on biological composition. According to the relative content of cyanobacteria, green algae, and Rhodophyta, the source rocks of the upper and lower Lucaogou Formation correspond to the low-salinity type (LS-type) and the high-salinity type (HS-type), respectively. Compared with LS-type source rocks, HS-type source rocks have greater generation potential of oil and weaker gas generation potential. This study is valuable for the accurate assessment of source rocks and holds significant practical implications for the exploration of oil and gas resources.

Affected by the complex mechanism of organic–inorganic interactions, the generation–retention–expulsion model of mixed siliciclastic–carbonate sediments is more complicated than that of common siliciclastic and carbonate shale deposited in lacustrine and marine environments. In this study, mixed siliciclastic–carbonate shale from Lucaogou Formation in Junggar Basin was selected for semi–closed hydrous pyrolysis experiments, and seven experiments were conducted from room temperature to 300, 325, 350, 375, 400, 450, and 500 °C, respectively. The quantities and chemical composition of oil, gases, and bitumen were comprehensively analyzed. The results show that the hydrocarbon generation stage of shale in Lucaogou Formation can be divided into kerogen cracking stage (300–350 °C), peak oil generation stage (350–400 °C), wet gas generation stage (400–450 °C), and gas secondary cracking stage (450–500 °C). The liquid hydrocarbon yield (oil + bitumen) reached the peak of 720.42 mg/g TOC at 400 °C. The saturate, aromatic, resin, and asphaltine percentages of bitumen were similar to those of crude oil collected from Lucaogou Formation, indicating that semi–closed pyrolysis could stimulate the natural hydrocarbon generation process. Lucaogou shale does not strictly follow the “sequential” reaction model of kerogen, which is described as kerogen firstly generating the intermediate products of heavy hydrocarbon compounds (NSOs) and NSOs then cracking to generate oil and gas. Indeed, the results of this study show that the generation of oil and gas was synchronous with that of NSOs and followed the “alternate pathway” mechanism during the initial pyrolysis stage. The hydrocarbon expulsion efficiency sharply increased from an average of 27% to 97% at 450 °C, meaning that the shale retained considerable amounts of oil below 450 °C. The producible oil reached the peak yield of 515.45 mg/g TOC at 400 °C and was synchronous with liquid hydrocarbons. Therefore, 400 °C is considered the most suitable temperature for fracturing technology.

The Shahejie Formation (Fm) in the Bohai Bay Basin is well-known for its substantial conventional resource potential and long-term history of exploration. Shale oil has been confirmed as a sustainable resource following breakthroughs in shale exploration in the first and third members of the Paleogene Shahejie Fm (Mbr1 and Mbr3) in Qikou Sag, particularly Mbr3, which has a more desirable output. However, the limited distribution of exploration wells for shale oil around the southwest of Qikou Sag calls for a comprehensive evaluation of shale oil (or gas) potential in all of Qikou Sag. Here, we clarify the shale oil (or gas) resource potential and areas favorable for exploration in Mbr3 by using a hydrocarbon generation potential model (HGPM) based on the material balance method and the principle of hydrocarbon (HC) generation dynamics. Apart from the quantified characteristics of the oil generation process of Mbr3 source rocks, the source rocks of both Mbr1 and Mbr3 were compared to interpret the discrepancies in HC generation. The results show that Mbr3 source rocks have high-quality geological and geochemical features, a thickness of 1200 m, and adequate organic matter (1.66% TOC on average, dominated by kerogen II&III, and in the mature stage). The threshold of expulsion is Ro = 0.78%; correspondingly, HC generation potential (Qg), HC expulsion potential (Qe), and retention potential (Qr) are, at maximum, 605.89, 169.65, and 436.24 mg HC/g TOC. The intensity of HC generation (Ig), expulsion (Ie), retention (Ir), and effective retention (Ire) is focused on the main depression and the Qibei Sub-sag and can reach as high as 250 × 104, 65 × 104, 170 × 104, and 110 × 104 t/km2, respectively. The resource potential for the retention of shale was calculated to be 13.3 × 108 t (movable shale oil and gas 8.0 × 108 t), and conventional and tight oil or gas resources were calculated to be 4.7 × 108 t (equivalent oil resources). Favorable exploration targets are spread around the main depression and the Qibei Sub-sag. There are disparities in the thermal process and thermal generation, and expulsion features between Mbr1 and Mbr3 source rocks are derived from kerogen-type and non-isolated deposit environments. Thus, a quantitative, advanced evaluation and a comparison offer more precise exploration predictions of shale in this Fm and further boost the low-risk exploration process.