Search

Energy storage is vital for a future where energy generation transitions from a fossil fuels-based one to an energy system that relies heavily on clean energy sources such as photovoltaic (PV) solar energy. To foster this transition, engineers and practitioners must have open-access models of PV systems coupled with battery storage systems (BESS). These models are fundamental to quantifying their economic and technical merits during the design phase. This paper contributes in this direction by carefully describing a model that accurately represents the power directions and energy dealings between the PV modules, the battery pack, and the loads. Moreover, the general model can be implemented using two different PV generation methods, the Gaussian model and the meteorological data-based model (MDB). We found that the MDB model is more appropriate for short-term analysis compared to the Gaussian model, while for long-term studies, the Gaussian model is closer to measured data. Moreover, the proposed model can reproduce two different energy management strategies: peak-shaving and maximizing self-consumption, allowing them to be used during PV–BESS sizing stages. Furthermore, the results obtained by the simulation are closed when compared to a real grid-tied PV–BESS, demonstrating the model’s validity.

Renewable energy power plants and transport and heating electrification projects are being deployed to enable the replacement of fossil fuels as the primary energy source. This transition encourages distributed generation but makes the grid more weather-dependent, thus reducing its inertia. Simultaneously, electrical network operators face voltage, frequency, and stability challenges at the distribution level. Networks were not designed to manage the stochasticity of renewable energy sources or the congestion caused by the new transport and heating demands. Such challenges are commonly addressed through infrastructure reinforcements. This review studies how energy storage systems with different carriers can provide a collaborative solution involving prosumers as ancillary services providers at the distribution level. We focused on the European urban context; thus, we analyzed renewable energy sources, batteries, supercapacitors, hydrogen fuel cells, thermal energy storage, and electric vehicles. A thorough review of successful implementations proved that including storage in one or more carriers benefits the distribution system operators and the prosumers, from both technical and economic perspectives. We propose a correlation between individual energy storage technologies and the ancillary services they can provide based on their responses to specific grid requirements. Therefore, distribution system operators can address network issues together with the prosumers. Nevertheless, attractive regulatory frameworks and business models are required to motivate prosumers to use their assets to support the grid. Further work is recommended to describe the joint operation of multiple storage technologies as multicarrier systems, focusing on the coupling of electrical and thermal energy storage. Additionally, how ancillary services affect the energy storage system’s aging should be studied.

Given the complementary nature of photovoltaic (PV) generation and energy storage, the combination of a solar panel and a battery pack in one single device is proposed. To realize this concept, the PV Battery-Integrated Module (PBIM), it is fundamental to analyze the system architecture and energy management. This paper focuses on selecting a suitable architecture among the different options, while also indicating the control strategy that the converters must follow to ensure appropriate performance. Also, several modes of operation for the complete system are introduced to implement energy management. For the selected DC architecture, two case studies, viz. off-grid and peak-shaving for a grid-tied system, were employed to characterize the response of the model demonstrating its utility to perform maximum power-point tracking, excess solar power curtailment, and battery charging and discharging. The proposed control and system architecture prove to be feasible for a PV battery-integrated device such as PBIM.

A scientific consensus is emerging on the benefits of direct current (DC) distribution in medium voltage (MV) power systems of ships and cities. At least 50% space savings and increased power transfer capacity are estimated with enhanced voltage DC operation of electric cables. The goal of this research is to contribute to developing the empirical knowledge on the insulation performance in order to validate the feasibility of such anticipated gains of DC versus alternating current (AC), and to determine the comparative impact of different operational conditions from a component engineering point of view. The partial discharge (PD) activity in cables is measured under AC and DC conditions as an indicator of insulation performance. Specifically, PDs in defects at the semicon-insulation interface are studied in terms of inception voltage, repetition rate and discharge magnitude. Empirical understanding is drawn for operating voltage and frequency dependence of the discharge behavior in such voids in the range of 10 to 20 kV and 0 to 0.1 Hz, respectively. The change in PD activity with void evolution post temperature-induced ageing process is explored.