Search

The flexible operation of carbon capture units is crucial for the economic performance of coal-fired power plants equipped with CO2 capture systems. This paper aims to investigate the impact of electricity, CO2, and fuel prices on the economic operation of such plants. A novel economic optimization model is proposed, integrating a static model of the carbon capture system with a particle swarm optimization algorithm. A new concept, the CO2 boundary price, is introduced as a key metric for determining the operating conditions of CO2 capture units. The CO2 boundary price rises when the power load decreases due to the decline in power generation efficiency, and it also increases with rising fuel prices, as the cost of steam for CO2 capture increases. Additionally, when the objective is to meet power load demand, CO2 prices have a great influence on the operation of CO2 capture units, assuming fixed coal and electricity prices. However, when the primary goal is to maximize plant profitability, the system's operational conditions are strongly influenced by the relative prices of electricity and CO2. The proposed optimization model and the uncovered price-effect mechanisms provide valuable insights into the economic operation of carbon capture power plants. [ABSTRACT FROM AUTHOR]

On the basis of "Carbon Peak and Carbon Neutral" goals, carbon sequestration projects are increasing in China. The integrity of cement sheaths, as an important factor affecting carbon sequestration projects, has also received more attention and research. When CO2 is injected into the subsurface from sequestration wells, the cement sheath may mechanically fail due to the pressure accumulated inside the casing, which leads to the sealing of the cement sheath failing. The elasticity and strength parameters of the cement sheath are considered in this paper. The critical bottom-hole injection pressures of inclined well sections under anisotropic formation stresses at different depths were calculated for actual carbon-sealing wells in the X block—the CO2 sequestration target block. The sensitivity factors of the critical bottom-hole injection pressure were also analyzed. It was found that the cement sheath damage criterion was tensile damage. The Young's modulus and tensile strength of the cement sheath are the main factors affecting the mechanical failure of the cement sheath, with Poisson's ratio having the second highest influence. An increase in the Young's modulus, Poisson's ratio, and tensile strength of the cement sheath can help to improve the mechanical stability of cement sheaths in CO2 sequestration wells. This model can be used for the design and evaluation of cement in carbon sequestration wells. [ABSTRACT FROM AUTHOR]

With the shortage of fossil energy and the increasingly serious environmental problems, renewable energy based on wind and solar power generation has been gradually developed. For the problem of wind power uncertainty and the low-carbon economic optimization problem of an integrated energy system with power to gas (P2G) and carbon capture and storage (CCS), this paper proposes an economic optimization scheduling strategy of an integrated energy system considering wind power uncertainty and P2G-CCS technology. Firstly, the mathematical model of the park integrated energy system with P2G-CCS technology is established. Secondly, to address the wind power uncertainty problem, Latin hypercube sampling (LHS) is used to generate a large number of wind power scenarios, and the fast antecedent elimination technique is used to reduce the scenarios. Then, to establish a mixed integer linear programming model, the branch and bound algorithm is employed to develop an economic optimal scheduling model with the lowest operating cost of the system as the optimization objective, taking into account the ladder-type carbon trading mechanism, and the sensitivity of the scale parameters of P2G-CCS construction is analyzed. Finally, the scheduling scheme is introduced into a typical industrial park model for simulation. The simulation result shows that the consideration of the wind uncertainty problem can further reduce the system's operating cost, and the introduction of P2G-CCS can effectively help the park's integrated energy system to reduce carbon emissions and solve the problem of wind and solar power consumption. Moreover, it can more effectively reduce the system's operating costs and improve the economic benefits of the park. [ABSTRACT FROM AUTHOR]

Municipal sewage sludge (MSS) is an inevitable byproduct of wastewater treatment, with increasing amounts year by year worldwide. The development of environmentally and economically acceptable methods for the sustainable management of MSS is a major environmental challenge. Nowadays, sludge management practices, besides the commonly used stabilization methods, focus attention on alternative sludge-disposal pathways, which encompass enhanced energy and valuable-resource recovery. This review presents the recent advances in the recovery of selected value-added products from sludge. Because of the high nitrogen and phosphorus concentrations, waste MSS can be a nutrient source (e.g., struvite). This paper discusses the conditions of and advances in the technology of struvite recovery. As in the extracellular polymeric substances (EPSs) of biological sludge, alginate-like exopolymers (ALEs) are present in MSS systems that treat municipal wastewater. The yields, dynamics in content, and characterization of ALEs and their possible applications were analyzed. MSS is an important source of humic substances. Their occurrence, characterization, and yields in various types of MSS (e.g., untreated, composted, and digested sludge) and main methods of application are presented. The important aspects and trends of MSS pyrolysis, including the thermochemical conversion to biochar, are discussed in this review. The characterization of biochar derived from MSS and the assessment of the environmental risks are also covered. This paper explores the potential use of biochar derived from MSS in various applications, including soil amendment, carbon sequestration, and environmental remediation. [ABSTRACT FROM AUTHOR]

This paper delves into the critical role of tax credits, specifically Sections 45Q and 45V, in the financing and economic feasibility of low-carbon-intensity hydrogen projects, with a focus on natural-gas-based hydrogen production plants integrated with carbon capture and storage (CCS). This study covers the current clean energy landscape, underscoring the importance of low-carbon hydrogen as a key component in the transition to a sustainable energy future, and then explicates the mechanics of the 45Q and 45V tax credits, illustrating their direct impact on enhancing the economic attractiveness of such projects through a detailed net present value (NPV) model analysis. Our analysis reveals that the application of 45Q and 45V tax credits significantly reduces the levelized cost of hydrogen production, with scenarios indicating a reduction in cost ranging from USD 0.41/kg to USD 0.81/kg of hydrogen. Specifically, the 45Q tax credit demonstrates a slightly more advantageous impact on reducing costs compared to the 45V tax credit, underpinning the critical role of these fiscal measures in enhancing project returns and feasibility. Furthermore, this paper addresses the inherent limitations of utilizing tax credits, primarily the challenge posed by the mismatch between the scale of tax credits and the tax liability of the project developers. The concept and role of tax equity investments are discussed in response to this challenge. These findings contribute to the broader dialogue on the financing of sustainable energy projects, providing valuable insights for policymakers, investors, and developers in the hydrogen energy sector. By quantifying the economic benefits of tax credits and elucidating the role of tax equity investments, our research supports informed decision-making and strategic planning in the pursuit of a sustainable energy future. [ABSTRACT FROM AUTHOR]

The increasing level of anthropogenic CO2 in the atmosphere has made it imperative to investigate an efficient method for carbon sequestration. Geological carbon sequestration presents a viable path to mitigate greenhouse gas emissions by sequestering the captured CO2 deep underground in rock formations to store it permanently. Geochemistry, as the cornerstone of geological CO2 sequestration (GCS), plays an indispensable role. Therefore, it is not just timely but also urgent to undertake a comprehensive review of studies conducted in this area, articulate gaps and findings, and give directions for future research areas. This paper reviews geochemistry in terms of the sequestration of CO2 in geological formations, addressing mechanisms of trapping, challenges, and ways of mitigating challenges in trapping mechanisms; mineralization and methods of accelerating mineralization; and the interaction between rock, brine, and CO2 for the long-term containment and storage of CO2. Mixing CO2 with brine before or during injection, using microbes, selecting sedimentary reservoirs with reactive minerals, co-injection of carbonate anhydrase, and enhancing the surface area of reactive minerals are some of the mechanisms used to enhance mineral trapping in GCS applications. This review also addresses the potential challenges and opportunities associated with geological CO2 storage. Challenges include caprock integrity, understanding the lasting effects of storing CO2 on geological formations, developing reliable models for monitoring CO2–brine–rock interactions, CO2 impurities, and addressing public concerns about safety and environmental impacts. Conversely, opportunities in the sequestration of CO2 lie in the vast potential for storing CO2 in geological formations like depleted oil and gas reservoirs, saline aquifers, coal seams, and enhanced oil recovery (EOR) sites. Opportunities include improved geochemical trapping of CO2, optimized storage capacity, improved sealing integrity, managed wellbore leakage risk, and use of sealant materials to reduce leakage risk. Furthermore, the potential impact of advancements in geochemical research, understanding geochemical reactions, addressing the challenges, and leveraging the opportunities in GCS are crucial for achieving sustainable carbon mitigation and combating global warming effectively. [ABSTRACT FROM AUTHOR]

In the context of constructing new power systems, the intermittency and volatility of high-penetration renewable generation pose new challenges to the stability and secure operation of power systems. Enhancing the ramping capability of power systems has become a crucial measure for addressing these challenges. Therefore, this paper proposes a bi-level peak regulation optimization model for power systems considering ramping capability and demand response, aiming to mitigate the challenges that the uncertainty and volatility of renewable energy generation impose on power system operations. Firstly, the upper-level model focuses on minimizing the ramping demand caused by the uncertainty, taking into account concerned constraints such as the constraint of price-guided demand response, the constraint of satisfaction with electricity usage patterns, and the constraint of cost satisfaction. By solving the upper-level model, the ramping demand of the power system can be reduced. Secondly, the lower-level model aims to minimize the overall cost of the power system, considering constraints such as power balance constraints, power flow constraints, ramping capability constraints of thermal power units, stepwise ramp rate calculation constraints, and constraints of carbon capture units. Based on the ramping demand obtained by solving the upper-level model, the outputs of the generation units are optimized to reduce operation cost of power systems. Finally, the proposed peak regulation optimization model is verified through simulation based on the IEEE 39-bus system. The results indicate that the proposed model, which incorporates ramping capability and demand response, effectively reduces the comprehensive operational cost of the power system. [ABSTRACT FROM AUTHOR]

This paper provides policy recommendations for accelerating the adoption of Fossil-Energy-Free Technologies and Strategies (FEFTS) in the EU agricultural sector. Faster adoption of these technologies and strategies is crucial to achieving the medium- and long-term sustainability targets laid out in EU policy. The prepared policy recommendations originate out of the key outputs and findings of the Horizon 2020 project "AgroFossilFree", including an assessment and evaluation of the current energy use status in EU agriculture, survey results on farmers' needs, ideas and interests on the adoption of FEFTS, FEFTS categories identified through an online inventory of FEFTS called the AgEnergy platform, and key innovative processes through national and transnational workshops that combine expertise from hundreds of keys stakeholders (researchers, innovation brokers, policymakers, farmers, and industry representatives). The policy recommendations are synthesized and presented in the form of 19 policy briefs split into three main categories: those that are related to energy issues in farming and can be applied to any farm and FEFTS type; those that are specific to certain agricultural production systems; and those that are necessary for FEFTS integration in agriculture in general. [ABSTRACT FROM AUTHOR]

Oxy-fuel combustion technology replaces air with a mixture of pure O2 and recycled flue gas for coal combustion, which leads to difficulties in the waste heat recovery of flue gas in the boiler tail of coal-fired power plants. This paper proposes a new integration scheme for waste heat recovery of flue gas in coal-fired power plants with oxy-fuel combustion CO2 capture. By introducing an oxygen preheater, a recycled flue gas preheater, and a low-pressure economizer, the waste heat of flue gas is fully recovered to preheat oxygen, recycled flue gas, and feed water, respectively. The proposed scheme simultaneously ensures the safe operation of the recycled fan and improves the thermal performance of the coal-fired power plants. Compared to the air combustion configuration, the boiler's efficiency and gross power efficiency in the oxy-fuel combustion configuration are increased by 0.42% and 1.29%, respectively. Due to power consumption for the added equipment, the net power efficiency is reduced by 10.41%. A techno-economic analysis shows that the cost of electricity for oxy-fuel combustion in coal-fired power plants has increased from USD 46.45/MWh to USD 80.18/MWh, and the cost of the CO2 avoided reaches USD 43.24/t CO2. [ABSTRACT FROM AUTHOR]

Carbon neutrality has become a global common goal. CCUS, as one of the technologies to achieve carbon neutrality, has received widespread attention from academia and industry. After CO2 enters the formation, under the conditions of formation temperature and pressure, supercritical CO2, formation water, and rock components interact, which directly affects the oil and gas recovery and carbon sequestration efficiency. In this paper, the recent progress on CO2 water–rock interaction was reviewed from three aspects, including (i) the investigation methods of CO2 water–rock interaction; (ii) the variable changes of key minerals, pore structure, and physical properties; and (iii) the nomination of suitable reservoirs for CO2 geological sequestration. The review obtains the following three understandings: (1) Physical simulation and cross-time scale numerical simulation based on formation temperature and pressure conditions are important research methods for CO2 water–rock interaction. High-precision mineral-pore in situ comparison and physical property evolution evaluation are important development directions. (2) Sensitive minerals in CO2 water–rock interaction mainly include dolomite, calcite, anhydrite, feldspar, kaolinite, and chlorite. Due to the differences in simulated formation conditions or geological backgrounds, these minerals generally show the pattern of dissolution or precipitation or dissolution before precipitation. This differential evolution leads to complex changes in pore structure and physical properties. (3) To select the suitable reservoir for sequestration, it is necessary to confirm the sequestration potential of the reservoir and the later sequestration capacity, and then select the appropriate layer and well location to start CO2 injection. At the same time, these processes can be optimized by CO2 water–rock interaction research. This review aims to provide scientific guidance and technical support for shale oil recovery and carbon sequestration by introducing the mechanism of CO2 water–rock interaction, expounding the changes of key minerals, pore structure, and physical properties, and summarizing the sequestration scheme. [ABSTRACT FROM AUTHOR]

In the current literature, there exists a lack of analysis regarding the coordination of the spinning reserve and time-shift characteristics of hydrogen storage systems (HSS) and flexible carbon capture systems (FCCS) in terms of low-carbon economic operation. They are presently used solely as a tool to capture carbon dioxide, without fully utilizing the advantages of their flexible operation. The coordination and complementarity of the FCCS and HSS can ensure stable power supply and improve renewable energy (RE) consumption. Combined with demand side response (DSR), these factors can maximize the RE consumption capacity, reduce carbon emissions, and improve revenue. In this paper, a source-storage-load flexible scheduling strategy is proposed by considering the complementary nature of FCCS and HSS in terms of rotating standby and time-shift characteristics. First, the operational mechanisms of FCCS, HSS, and demand side response (DSR) are analyzed, and their mathematical models are constructed to improve flexibility in grid operation and regulation. Next, deficiencies in FCCS and HSS operation under rotating reserve requirements are analyzed to design a coordinated operation framework for the FCCS and HSS. This operational framework aims to enable the complementarity of the rotating reserve and time-shift characteristics of FCCS and HSS. Finally, based on the carbon emission trading mechanism, a three-stage ladder carbon emission trading cost model is constructed, and a source-storage-load flexible scheduling strategy is established to achieve an effective balance between low carbon emissions and economic performance. The simulation results demonstrate that the strategy reduces the overall cost by 8.57%, reduces the carbon emissions by 35.33%, and improves the renewable energy consumption by 3.5% compared with the unoptimized scheme. [ABSTRACT FROM AUTHOR]

CO2–slickwater hybrid fracturing technology is an essential part of shale gas recovery and CO2 geo-storage. However, the exposure to supercritical CO2 (ScCO2) and slickwater can result in potential changes of the pore structures and surface wetting behavior, which affect the gas transportation and CO2 sequestration security in shale reservoirs. Therefore, in this paper, X-ray diffraction (XRD), low-pressure nitrogen gas adsorption (N2GA), mercury intrusion porosimetry (MIP), and fractal analysis were used to describe the pore characteristics of shale before and after ScCO2–slickwater coupling treatments. Shale's surface wettability was confirmed by contact angle measurements. After the ScCO2–slickwater treatments, the number of micropores (<3.5 nm) and mesopores (3.5–50 nm) increased, while that of macropores (>50 nm) declined based on the N2GA and MIP experiments. Combined with fractal analysis, we argue that the pore connectivity diminished and the pore structure became more complicated. By analyzing the results of XRD, shale pore changes occurring after the ScCO2–slickwater treatment can be explained by the adsorption of polyacrylamide (PAM). Contact angle measurement results showed that the shale's surface treated by ScCO2 and slickwater was more hydrophilic than that treated by ScCO2 and water, and indirectly prove our argument above. Hence, the coupling using effect of ScCO2 and slickwater can impair the negative effect of CO2 on the shale capillary force to improve shale gas productivity, but it can negatively affect the security of CO2 sequestration in shale reservoirs. [ABSTRACT FROM AUTHOR]

Carbon dioxide (CO2) capture and storage (CCS) is frequently identified as a potential component to achieving a decarbonized power system at least cost; however, power system models frequently lack detailed representation of CO2 transportation, injection, and storage (CTS) infrastructure. In this paper, we present a novel approach to explicitly represent CO2 storage potential and CTS infrastructure costs and constraints within a continental-scale power system capacity expansion model. In addition, we evaluate the sensitivity of the results to assumptions about the future costs and performance of CTS components and carbon capture technologies. We find that the quantity of CO2 captured within the power sector is relatively insensitive to the range of CTS costs explored, suggesting that the cost of CO2 capture retrofits is a more important driver of CCS implementation than the costs of transportation and storage. Finally, we demonstrate that storage and injection costs account for the predominant share of total costs associated with CTS investment and operation, suggesting that pipeline infrastructure costs have limited influence on the competitiveness of CCS. [ABSTRACT FROM AUTHOR]

This paper presents a comprehensive analysis of supercritical carbon dioxide (sCO2)-enhanced geothermal systems (EGSs) in Poland, focusing on their energetic performance through process modeling and optimization. EGSs harness the potential of geothermal energy by utilizing supercritical carbon dioxide as the working fluid, offering promising avenues for sustainable power generation. This study investigates two distinct configurations of sCO2-EGS: one dedicated to power generation via a binary system with an organic Rankine cycle and the other for combined power and heat production through a direct sCO2 cycle. Through accurate process modeling and simulation, key parameters influencing system efficiency and performance are identified and optimized. The analysis integrates thermodynamic principles with geological and operational constraints specific to the Polish context. The results highlight the potential of sCO2-EGSs to contribute to the country's energy transition, offering insights into the optimal design and operation of such systems for maximizing both power and thermal output while ensuring economic viability and environmental sustainability. [ABSTRACT FROM AUTHOR]

Direct air capture (DAC) systems that capture carbon dioxide (CO2) directly from the atmosphere are garnering considerable attention for their potential role as negative emission technologies in achieving net-zero CO2 emission goals. Common DAC technologies are based either on liquid–solvent (L-DAC) or solid–sorbent (S-DAC) to capture CO2. A comprehensive multi-factor comparative economic analysis of the deployment of L-DAC and S-DAC facilities across various United States (U.S.) cities is presented in this paper. The analysis considers the influence of various factors on the favorability of DAC deployment, including local climatic conditions such as temperature, humidity, and CO2 concentrations; the availability of energy sources to power the DAC system; and costs for the transport and storage of the captured CO2 along with the consideration of the regional market and policy drivers. The deployment analysis in over 70 continental U.S. cities shows that L-DAC and S-DAC complement each other spatially, as their performance and operational costs vary in different climates. L-DAC is more suited to the hot, humid Southeast, while S-DAC is preferrable in the colder, drier Rocky Mountain region. Strategic deployment based on regional conditions and economics is essential for promoting the commercial adoptability of DAC, which is a critical technology to meet the CO2 reduction targets. [ABSTRACT FROM AUTHOR]

The paper addresses the overlooked interaction between power-to-gas (P2G) devices and carbon capture and storage (CCS) equipment, along with the stepwise carbon trading mechanism in the context of current multi-park integrated energy microgrids (IEMGs). Additionally, it covers the economic and coordinated low-carbon operation issues in multi-park IEMGs under the carbon trading system. It proposes a multi-park IEMG low-carbon operation strategy based on the synchronous Alternating Direction Method of Multipliers (ADMM) algorithm. The algorithm first enables the distribution of cost relationships among multi-park IEMGs. Then, using a method that combines a CCS device with a P2G unit in line with the tiered carbon trading scheme, it expands on the model of single IEMGs managing thermal, electrical, and refrigeration energy. Finally, the comparison of simulation cases proves that the proposed strategy significantly reduces the external energy dependence while keeping the total cost of the users unchanged, and the cost of interaction with the external grid is reduced by 56.64%, the gas cost is reduced by 27.78%, and the carbon emission cost is reduced by 29.54% by joining the stepped carbon trading mechanism. [ABSTRACT FROM AUTHOR]

Advancing the modeling of evaporation and salt precipitation is essential in CO2 storage processes in aquifers. OpenFOAM provides a platform for computational fluid dynamics (CFD) modeling with its open-source C++ object-oriented architecture that can especially be used in the development of fluid flow models in porous media. Some OpenFOAM packages have been developed in this area, and their codes are available for use. Despite this, the existing OpenFOAM literature does not include a model that incorporates multicomponent interactions in multi-phase flow systems, referred to as compositional modeling, at the Darcy scale. This existing gap is addressed in this paper, where a new simple model in OpenFOAM is introduced that aims to model the interaction of CO2 and H2O components in CO2 storage processes in aquifers at the Darcy scale. The model, named compositionalIGFoam, incorporates a compositional solver by extending the impesFoam solver of the porousMultiphaseFoam package, while assuming some simplifications, to account for CO2/water mutual dissolution, relevant to carbon capture and storage (CCS) processes in aquifers. The functionality of the compositionalIGFoam solver was assessed by showcasing its ability to reproduce the outcomes of existing examples. In addition to that, the process of gas injection into a water-saturated core sample was simulated using the developed model to mimic CO2 injection into aquifers. The CMG-GEM commercial compositional simulator was used to compare its results with the coreflood model of this study. Phenomenal agreement was achieved with the GEM model, showing only 1.8% and 0.4% error for both components. This confirms the accuracy and reliability of the developed model. In conclusion, this study enhances the state of the art in porous media modeling using OpenFOAM 10, providing a valuable tool for examining fluid interactions in subsurface environments, especially within the context of CCS processes. [ABSTRACT FROM AUTHOR]

The urgent need to find mitigating pathways for limiting world CO2 emissions to net zero by 2050 has led to intense research on CO2 sequestration in deep saline reservoirs. This paper reviews key advancements in lab- and simulation-scale research on petrophysical, geochemical, and mineralogical changes during CO2–brine–rock interactions performed in the last 25 years. It delves into CO2 MPD (mineralization, precipitation, and dissolution) and explores alterations in petrophysical properties during core flooding and in static batch reactors. These properties include changes in wettability, CO2 and brine interfacial tension, diffusion, dispersion, CO2 storage capacity, and CO2 leakage in caprock and sedimentary rocks under reservoir conditions. The injection of supercritical CO2 into deep saline aquifers can lead to unforeseen geochemical and mineralogical changes, possibly jeopardizing the CCS (carbon capture and storage) process. There is a general lack of understanding of the reservoir's interaction with the CO2 phase at the pore/grain scale. This research addresses the gap in predicting the long-term changes of the CO2–brine–rock interaction using various geochemical reactive transport simulators. Péclet and Damköhler numbers can contribute to a better understanding of geochemical interactions and reactive transport processes. Additionally, the dielectric constant requires further investigation, particularly for pre- and post-CO2–brine–rock interactions. For comprehensive modeling of CO2 storage over various timescales, the geochemical modeling software called the Geochemist's Workbench was found to outperform others. Wettability alteration is another crucial aspect affecting CO2–brine–rock interactions under varying temperature, pressure, and salinity conditions, which is essential for ensuring long-term CO2 storage security and monitoring. Moreover, dual-energy CT scanning can provide deeper insights into geochemical interactions and their complexities. [ABSTRACT FROM AUTHOR]

This review presents a recent study on improving energy crops (ECs) in the EU and discusses the potential use of biostimulants to enhance CO2 sequestration processes in these plants. The novelty of this study lies in demonstrating alternative directions for improving productivity and increasing plant yield without relying on introducing new hybrids (GM) or using advanced agrotechnology. There is a great deal of discussion about using energy crops for direct combustion or biogas production. However, there is a paucity of information regarding the use of biostimulants and their role in increasing the yield of energy crops, particularly in terms of CO2 compensation. In CO2 sequestration, increasing the intensity of the photosynthetic process is considered crucial for the more efficient growth of energy crops. Traditionally, fertilization aimed at improving photosynthesis results in a large amount of alkaline elements, which can cause negative effects in boilers. This paper describes the use of amino acid biostimulants extracted from industrial waste, either chemically or biotechnologically, and their different forms of application. It addresses the current challenges and benefits of using biostimulants in energy crops to increase photosynthesis without the use of genetic engineering tools in plants. [ABSTRACT FROM AUTHOR]

Extralow-permeability reservoirs have emerged as a significant area of focus for CO2 geological sequestration due to their stable subterranean structure and expansive storage capacity, offering substantial potential in addressing global climate change. However, the full extent of CO2 geological sequestration potential within these extralow-permeability reservoirs remains largely unexplored. To address this gap, this paper utilizes the Shahejie Formation (Es1 member) of the Shuang 229 block in the Liaohe oilfield, Bohai Bay Basin, as a case study. This section is characterized by its abundant oil-gas reserves and serves as an exemplar for conducting experimental research on CO2 storage within extralow-permeability reservoirs. The results demonstrate that the reservoir lithology of the Es1 member is fine sandstone and siltstone, with high compositional and structural maturity. Moreover, the average porosity is 14.8%, the average permeability is 1.48 mD, and the coefficient of variation of the reservoir is approximately 0.5, which indicates a low- to extralow-permeability homogeneous reservoir. In addition, the overburden pressure is >2.0 MPa, the fault can withstand a maximum gas column height of >200 m, and the reservoir exhibits favorable overburden and fault sealing characteristics. Notably, stepwise increasing gas injection in the Shuang 229-36-62 well reveals that the injected liquid CO2 near the wellhead exhibits a relatively high density, close to 1.0 g/cm3, which gradually decreases to approximately 0.78 g/cm3 near a depth of 2000 m underground. The injected fluid changes into a supercritical state upon entering the formation, and the CO2 injection speed is optimal, at 0.08 HCPV/a. According to these findings, it is predicted that the highest burial CO2 volume via the injection of 1.5 HCPVs in the Wa 128 block area is 1.11 × 105 t/year, and the cumulative burial volume reaches approximately 2.16 × 106 t. This shows that the CO2 sequestration potential of extralow-permeability reservoirs is considerable, providing confidence for similar instances worldwide. [ABSTRACT FROM AUTHOR]

Carbon geological storage (CGS) is one of the key processes in carbon capture and storage (CCS) technologies, which are used to reduce CO2 emissions and achieve carbon-neutrality and net-zero emissions in developing countries. In Thailand, the Mae Moh basin is a potential site for implementing CGS due to the presence of a structural trap that can seal the CO2 storage formation. However, the cost of CGS projects needs to be subsidized by selling carbon credits in order to reach the project breakeven. Therefore, this paper estimates the economic components of a CGS project in the Mae Moh basin by designing the well completion and operating parameters for CO2 injection. The capital costs and operating costs of the process components were calculated, and the minimum carbon credit cost required to cover the total costs of the CGS project was determined. The results indicate that the designed system proposes an operating gas injection rate of 1.454 MMscf/day, which is equivalent to 29,530 tCO2e per year per well. Additionally, the minimum carbon credit cost was estimated to be USD 70.77 per tCO2e in order to achieve breakeven for the best case CGS project, which was found to be much higher than the current market price of carbon credit in Thailand, at around USD 3.5 per tCO2e. To enhance the economic prospects of this area, it is imperative to promote a policy of improving the cost of carbon credit for CGS projects in Thailand. [ABSTRACT FROM AUTHOR]

With a significant share of renewable power generation integrated into the power supply, it is crucial to timely adjust the regulating peak load for coal-fired power plants equipped with CO2 capture to ensure the stable operation of the multi-energy supply system. In this paper, the effects of varying boiler loads on the techno-economic performance of the retrofitted power plant were studied. Furthermore, the potential for reducing the cost of CO2 capture was investigated, and early opportunities for demonstration were discussed. Results showed that when the boiler load decreased from 100% turbine heat acceptance condition to 50% turbine heat acceptance condition, the cost of CO2 capture increased from 37.0 $/t CO2 to 57.0 $/t CO2, cost contribution of energy penalty and extra capital investment also increased from 20.6 $/t-CO2 to 25.7 $/t-CO2, and from 16.4 $/t-CO2 to 31.3 $/t-CO2, respectively. Furthermore, by improving separation efficiency from 0.15 to 0.5, a 25% to 30% reduction in CO2 capture cost can be achieved. The cost of CO2 capture could decrease by 42.2–50.5% when the cumulative capacity reaches 250 GW under the high investment learning rate scenario. According to the distribution of coal prices and renewable energy sources in China, the early demonstration projects of multi-energy supply systems should prioritize the northern region. The results of this work can provide informative references for making roadmaps and policies for CO2 emission reduction toward carbon neutrality. [ABSTRACT FROM AUTHOR]

Carbon capture and storage (CCS) is a critical technology for mitigating greenhouse gas emissions and combating climate change. CCS involves capturing CO2 emissions from industrial processes and power plants and injecting them deep underground for long-term storage. The success of CCS projects is influenced by various factors, including the regional pressure dissipation effects in subsurface geological formations. The safe and efficient operation of CCS projects depends on maintaining the pressure in the storage formation. Regional pressure dissipation, often resulting from the permeability and geomechanical properties of the storage site, can have significant effects on project integrity. This paper provides a state-of-art of the impact of regional pressure dissipation on CCS projects, highlights its effects, and discusses ongoing investigations in this area based on different case studies. The results corroborate the idea that the Sleipner project has considerable lateral hydraulic connectivity, which is evidenced by pressure increase ranging from <0.1 MPa in case of an uncompartmentalized reservoir to >1 MPa in case of substantial flow barriers. After five years of injection, pore pressures in the water leg of a gas reservoir have increased from 18 MPa to 30 MPa at Salah project, resulting in a 2 cm surface uplift. Furthermore, artificial CO2 injection was simulated numerically for 30 years timespan in the depleted oil reservoir of Jurong, located near the Huangqiao CO2-oil reservoir. The maximum amount of CO2 injected into a single well could reach 5.43 × 106 tons, potentially increasing the formation pressure by up to 9.5 MPa. In conclusion, regional pressure dissipation is a critical factor in the implementation of CCS projects. Its impact can affect project safety, efficiency, and environmental sustainability. Ongoing research and investigations are essential to improve our understanding of this phenomenon and develop strategies to mitigate its effects, ultimately advancing the success of CCS as a climate change mitigation solution. [ABSTRACT FROM AUTHOR]

Hydrogen is an emerging technology changing the context of heating with cleaner combustion than traditional fossil fuels. Studies indicate the potential to repurpose the existing natural gas infrastructure, offering consumers a sustainable, economically viable option in the future. The integration of hydrogen in combined heat and power systems could provide residential energy demand and reduce environmental emissions. However, the widespread adoption of hydrogen will face several challenges, such as carbon dioxide emissions from the current production methods and the need for infrastructure modification for transport and safety. Researchers indicated the viability of hydrogen in decarbonizing heat, while some studies also challenged its long-term role in the future of heating. In this paper, a comprehensive literature review is carried out by identifying the following key aspects, which could impact the conclusion on the overall role of hydrogen in heat decarbonization: (i) a holistic view of the energy system, considering factors such as renewable integration and system balancing; (ii) consumer-oriented approaches often overlook the broader benefits of hydrogen in emission reduction and grid stability; (iii) carbon capture and storage scalability is a key factor for large-scale production of low-emission blue hydrogen; (iv) technological improvements could increase the cost-effectiveness of hydrogen; (v) the role of hydrogen in enhancing resilience, especially during extreme weather conditions, raises the potential of hydrogen as a flexible asset in the energy infrastructure for future energy supply; and finally, when considering the UK as a basis case, (vi) incorporating factors such as the extensive gas network and unique climate conditions, necessitates specific strategies. [ABSTRACT FROM AUTHOR]

Carbon dioxide, the leading contributor to anthropogenic climate change, is released mainly via fossil fuel combustion, mostly for energy generation. Carbon capture technologies are employed for reducing the emissions from existing huge point sources, along with capturing them from direct air, to reduce the existing concentration. This paper provides a quantitative analysis of the various subtypes of carbon capture technologies with the aim of providing an assessment of each from technological, social, geo-political, economic, and environmental perspectives. Since the emissions intensity and quantity, along with the social–political–economic conditions, vary in different geographic regions, prioritising and finding the right type of technology is critical for achieving ambitious net-zero targets. Four main types of carbon capture technology were analysed (adsorption, absorption, membrane, and cryogenic) under four scenarios depending on the jurisdiction. The Technique for Order of Preference by Similarity to Ideal Solution (also known as the TOPSIS method) was used to establish a quantitative ranking of each, where weightages were allocated according to the emissions status and economics of each depending on the jurisdiction. Furthermore, forecasting the trends for technology types vis à vis carbon neutral targets between 2040 and 2050 was carried out by applying regression analysis on existing data and the emissions footprint of major contributing countries. The study found the membrane score to be the highest in the TOPSIS analysis in three of the four scenarios analysed. However, absorption remains the most popular for post-combustion capture despite having the highest energy penalty per ton of CO2 capture. Overall, capture rates are well short of projections for carbon neutrality; the methodology put forward for prioritising and aligning appropriate technologies and the region-by-region analysis will help highlight to technocrats, governments, and policymakers the state of the art and how to best utilise them to mitigate carbon emissions—critical in achieving the net-zero goals set at various international agreements on climate change. [ABSTRACT FROM AUTHOR]

Hydrogen from natural gas reforming can be produced efficiently with a high CO2 capture rate. This can be achieved through oxygen-blown autothermal reforming as the core technology, combined with pressure-swing adsorption for hydrogen purification and refrigeration-based tail gas separation for CO2 capture and recirculation of residual hydrogen, carbon monoxide, and methane. The low-temperature tail gas separation section is presented in detail. The main objective of the paper is to study and quantify the exergy efficiency of this separation process in detail. To achieve this, a detailed exergy analysis is conducted. The irreversibilities in 42 different process components are quantified. In order to provide transparent verification of the consistency of exergy calculations, the total irreversibility rate is calculated by two independent approaches: Through the bottom-up approach, all individual irreversibilities are added to obtain the total irreversibility rate. Through the top-down approach, the total irreversibility rate is calculated solely by the exergy flows crossing the control volume boundaries. The consistency is verified as the comparison of results obtained by the two methods shows a relative deviation of 4 · 10 − 7 . The exergy efficiency of the CO2 capture process is calculated, based on two different definitions. Both methods give a baseline exergy efficiency of 58.38%, which indicates a high degree of exergy utilisation in the process. [ABSTRACT FROM AUTHOR]

This paper reviews and evaluates work on the structural complexity of the potential carbon dioxide storage sites in the North Sea, including the nature of the reservoir structures, the reservoir rocks, the presence of inter-layers, faults, and fractures, and how these factors influence carbon dioxide capacity. In particular, the review emphasises the significance of studying caprocks in detail, not just the reservoir rock's carbon dioxide storage capacity. This work also particularly considers reservoir simulation work on North Sea sites and illustrates the importance of using fully coupled flow–geomechanical–geochemical modelling to ensure that complex feedback and synergistic effects are not missed. It includes comparisons with other sites where relevant. It also discusses recent challenges and controversies that have arisen from simulations of sequestration in North Sea reservoirs and the need for comprehensive field data to resolve these issues. [ABSTRACT FROM AUTHOR]

The document discusses the importance of Carbon Capture, Utilization, and Storage (CCUS) technology in mitigating climate change by capturing CO2 and either utilizing it for chemical applications or storing it in geological formations. Various studies explore innovative methods for CO2 capture, utilization, and storage, including the development of low-energy separation processes and enhanced CO2 adsorption capacities. Additionally, research delves into the impact of CCUS technologies on carbon emissions, public perception, and strategic priorities for achieving dual carbon goals, emphasizing the need for continued exploration and development in this field. [Extracted from the article]

This study investigates a novel method of utilizing Direct Air Capture (DAC) technology for fertilizer production. Unlike traditional Direct Air Carbon Capture and Utilization (DACCU) technologies, Direct Air Carbon Capture for Fertilizers (FDAC) has the potential to produce fertilizers directly. This study aims to assess the feasibility of FDAC-based fertilizer production by examining the current state of traditional DAC technologies, evaluating the CO2 fixation potential of FDAC, and analyzing the decarbonization effect of producing fertilizers using FDAC. Our evaluation results indicate that CO2 emissions from producing 1 ton of conventional chemical fertilizer, FDAC fertilizer (current status), FDAC fertilizer with ingredient adjustment (sodium hydroxide), and FDAC fertilizer with ingredient adjustment (magnesium hydroxide) are 1.69, 1.12, 1.04, and 1.06 tons of CO2, respectively. The FDAC fertilizer (current status) emits 0.57 tons of CO2 per ton less than commercial fertilizers. FDAC fertilizers also have the potential to reduce CO2 emissions further when the fertilizer composition is adjusted, offering a promising solution for lowering the environmental impact of fertilizer production. Significant CO2 reduction can be expected by replacing conventional low-intensity chemical fertilizers with FDAC-produced fertilizers. [ABSTRACT FROM AUTHOR]

Fighting climate change has become a major task worldwide. One of the key energy sectors to emit greenhouse gases is transportation. Therefore, long term strategies all over the world have been set up to reduce on-road combustion emissions. In this context, the road freight sector faces significant challenges in decarbonization, driven by its limited availability of low-emission fuels and commercialized zero-emission vehicles compared with its high energy demand. In this work, we develop the Mobility and Energy Transportation Analysis (META) Model, a python-based optimization model to quantify the impact of transportation projected policies on freight transport by projecting conventional and alternative fuel technologies market acceptance as well as greenhouse gas (GHG) emissions. Along with introducing e-fuels as an alternative refueling option for conventional vehicles, META investigates the market opportunities of Mobile Carbon Capture (MCC) until 2050. To accurately assess this technology, a techno-economic analysis is essential to compare MCC abatement cost to alternative decarbonization technologies such as electric trucks. The novelty of this work comes from the detailed cost categories taken into consideration in the analysis, including intangible costs associated with heavy-duty technologies, such as recharging/refueling time, cargo capacity limitations, and consumer acceptance towards emerging technologies across different regions. Based on the study results, the competitive total cost of ownership (TCO) and marginal abatement cost (MAC) values of MCC make it an economically promising alternative option to decarbonize the freight transport sector. Both in the KSA and EU, MCC options could reach greater than 50% market shares of all ICE vehicle sales, equivalent to a combined 35% of all new sales shares by 2035. [ABSTRACT FROM AUTHOR]

This study aimed to assess the potential of soil organic carbon (SOC) production through organic amendments. SOC sequestration would help to achieve the net-zero emissions targets set by the Intergovernmental Panel on Climate Change (IPCC). Given the urgency to reduce greenhouse gas emissions, traditional methods that estimate SOC over 100 years must be revised. Hence, a novel fate transport numerical model was developed to forecast SOC levels relevant to individual countries' net-zero targets in various time frames. The simulation results revealed that most countries had sufficient organic amendment to mitigate the CO2 emission of that country for a year if the organic amendment was applied on 20% of the arable land. However, if a significant fraction of the total CO2 emissions needs to be mitigated before reaching the net zero target, the requirements of organic amendments need to be increased several folds. All the available agricultural land should also be brought under the organic amendment regime. Later, the dynamic LCA approach was undertaken for estimating Global Warming (GWP) from land-applied organic residue. It was observed that, depending on the dynamic LCA model, the estimated GWP was different. However, the estimated dynamic GWP was very close to the residual SOC calculated through the fate transport model. The mass of organic residues generated from a biorefinery was examined by employing a waste biorefinery model to explore further the routes of acquiring additional organic amendment. Simulated results showed that while a waste biorefinery could not provide additional organic residue compared to the original organic waste input, it was highly efficient for nutrient recovery and its uses. This study demonstrated that organic amendment-based carbon sequestration adequately mitigated residual GHG at the net-zero target. [ABSTRACT FROM AUTHOR]

This study investigates the feasibility of utilizing carbon dioxide (CO2) as a cushion gas in depleted reservoirs for enhanced gas storage efficiency and carbon sequestration against the backdrop of rising natural gas stable supply demand and climate change concerns. Simulations of gas storage reservoir scenarios require accurate dispersion parameters at flow alternation conditions to quantify the size of the miscible displacement front. Several experimental studies using core-flooding equipment aimed at measuring related parameters have been reported over the last decade but did not take flow alternation into consideration. We simulated directionally variable displacements to mimic the cyclic injection and extraction processes in gas storage, focusing on the dispersion characteristics of CO2 and methane (CH4) during flow alternation. Key findings were observed using Nuclear Magnetic Resonance (NMR) imaging, which provided real-time data on the spatial distribution and temporal changes of CH4 signals in rock cores. The results revealed that dispersion, influenced predominantly by dispersion coefficients rather than molecular diffusion, was significantly higher during alternating flow compared to concurrent displacement. Additionally, CO2 exhibited a greater dispersion effect when displacing CH4 than the reverse. This enhanced mixing efficiency during flow alternation supports the potential of CO2 as a cost-effective and efficient cushion gas, offering both improved storage performance and the added benefit of CO2 sequestration. These findings contribute valuable insights for the numerical simulation and operational adaptation of CO2 in gas storage reservoirs, emphasizing the importance of understanding fluid interactions under varying flow conditions to optimize storage efficiency and environmental benefits. [ABSTRACT FROM AUTHOR]

Climate change demands urgent action to limit greenhouse gas (GHG) emissions and explore methods for atmospheric carbon removal. Forest residues, a significant biomass resource, represent a readily available solution. With the use of life cycle assessment (LCA), this study investigates the environmental advantages of thermochemical processes utilizing forest residues to produce valuable energy-dense products, like syngas, bio-oil, and biochar, providing a carbon sink. While slow pyrolysis emphasizes biochar production for carbon sequestration, gasification focuses on bioenergy generation. This research evaluates the environmental performance of both techniques in terms of carbon sequestration and GHG emissions mitigation. This comprehensive analysis aims to identify critical factors influencing the environmental sustainability of thermochemical processes in forest management. The findings aim to contribute to achieving sustainable development goals by highlighting the environmental advantages of biochar in mitigating climate change. [ABSTRACT FROM AUTHOR]

A Carbon Footprint (CF) is defined as the total emissions of greenhouse gases, primarily carbon dioxide, methane, and nitrous oxide, and is a specific type of Environmental Footprint that measures human impact on the environment. Carbon dioxide emissions are a major contributor to anthropogenic greenhouse gases driving climate change. Wood, as a renewable and ecological material, has relatively low carbon emissions. The study aimed to review and analyze the criteria influencing the feasibility of constructing modern zero-carbon wooden buildings. The review was conducted in two phases: (i) a literature review and (ii) an assessment of existing buildings. The preliminary research led to (i) narrowing the focus to the years 2020–2024 and (ii) identifying key criteria for analysis: sustainable material sourcing, carbon sequestration, energy efficiency, life cycle assessment (LCA), and innovative construction practices. The study's findings indicate that all these criteria play a vital role in the design and construction of new zero-carbon wooden buildings. They highlight the significant potential of wood as a renewable material in achieving zero-carbon buildings (ZCBs), positioning it as a compelling alternative to traditional construction materials. However, the research also underscores that despite wood's numerous potential benefits, its implementation in ZCBs faces several challenges, including social, regulatory, and financial barriers. [ABSTRACT FROM AUTHOR]

Biomass gasification has emerged as a promising method for producing renewable energy, addressing both energy and environmental challenges. This review examines recent research on gasification simulations, covering a range of topics from process modeling to syngas cleanup. Key areas explored include techniques for syngas cleaning, addressing tar formation, and CO2 capture methods. The aim of this review is to provide an overview of the current state of gasification simulation and identify potential areas for future research and development. This work serves as an invaluable resource for researchers, engineers, and industry professionals involved in biomass gasification modeling. By providing a comprehensive guide to biomass gasification simulation using Aspen Plus software and comparing various modeling approaches, it assists users in selecting the most effective tool for optimizing the design and operation of gasification systems. [ABSTRACT FROM AUTHOR]

CCUS technologies are crucial solutions for mitigating climate change by reducing CO2 emissions from industrial operations and energy sectors. This review critically examines the current state of CCUS technologies, and highlights advancements, challenges, regulatory frameworks, and future directions. It comprehensively analyzes carbon capture methods, such as pre-combustion, post-combustion, and oxy-fuel combustion capture, while comparing their efficiencies and limitations. The review also explores carbon utilization techniques, such as direct and indirect utilization, emphasizing their potential applications and technological constraints. Additionally, it assesses various carbon storage methods, focusing on geological, ocean, and mineralization storage, and discusses their capacity, feasibility, and environmental implications. The study reviews the policy and regulatory frameworks, economic viability, market trends, and environmental sustainability of CCUS. By identifying research gaps and recommending future research priorities, this review aims to guide the development of more efficient/effective, and cost-effective CCUS technology, ensuring their role in a sustaining low-carbon future. This review provides a forward-looking perspective, a critical and interdisciplinary analysis that assesses the current state of CCUS technologies, and further provides a roadmap for future development. [ABSTRACT FROM AUTHOR]

The need to limit anthropogenic climate change to 1.5–2 °C, as agreed in the Paris Agreement, requires a significant reduction of CO2 emissions resulting from the use of fossil carbon. However, based on current knowledge, carbon is expected to remain crucial in certain industrial sectors, e.g., the chemical industry. Consequently, it is essential to identify and utilize sustainable carbon sources in the future. In this context, various carbon sources were examined and classified in terms of their disruption of the Earth's (fast) carbon cycle. Furthermore, the examined carbon sources were qualitatively analyzed with regard to their technical readiness level, their energy expenditure, and their current and future availability, as well as legal regulation within the European Union. As a result, only biogenic and mixed carbon from the ambient air can be considered genuinely sustainable within the Earth's (fast) carbon cycle. Mixed carbon streams, e.g., from waste recycling, fall into a gray area. The same applies to certain process-related emissions that originally descend from fossil fuel energy. In terms of energy considerations, technical maturity, and exploitable potentials, prioritizing the utilization of biogenic carbon sources is advisable for the time being, especially for CO2 produced as a by-product originating from biogenic carbon carriers. [ABSTRACT FROM AUTHOR]

After the completion of in situ pyrolysis, oil shale can be used as a natural place for CO2 sequestration. However, the effects of chemical action and formation stress-state changes on the deformation of oil shale should be considered when CO2 is injected into oil shale after pyrolysis. In this study, combined with statistical damage mechanics, a transverse isotropic model of oil shale with coupled damage mechanisms was established by considering the decreased mechanical properties and the chemical damage caused by CO2 injection. The process of injecting supercritical CO2 into oil shale after pyrolysis was simulated by COMSOL6.0. The volume distribution of CO2 and the stress evolution in oil shale were analyzed. It is found that CO2 injection into oil shale after pyrolysis will not produce new force damage, and the force damage caused by the decrease in the mechanical properties of oil shale after pyrolysis can offset the ground uplift caused by CO2 injection to a certain extent. Under the combined action of chemical damage and mechanical damage, the uplift of a formation with a thickness of 200 m is only 10 cm. The injection of supercritical CO2 is beneficial for maintaining the stability of oil shale after in situ pyrolysis. [ABSTRACT FROM AUTHOR]

Depleted gas reservoirs with bottom water show significant potential for long-term CO2 storage. The residual gas influences mass-transfer dynamics, further affecting CO2 dissolution and convection in porous media. In this study, we conducted a series of numerical simulations to explore how residual-gas mixtures impact CO2 dissolution trapping. Moreover, we analyzed the CO2 dissolution rate at various stages and delineated the initiation and decline of convection in relation to gas composition, thereby quantifying the influence of residual-gas mixtures. The findings elucidate that the temporal evolution of the Sherwood number observed in the synthetic model incorporating CTZ closely parallels that of the single-phase model, but the order of magnitude is markedly higher. The introduction of CTZ serves to augment gravity-induced convection and expedites the dissolution of CO2, whereas the presence of residual-gas mixtures exerts a deleterious impact on mass transfer. The escalation of residual gas content concomitantly diminishes the partial pressure and solubility of CO2. Consequently, there is an alleviation of the concentration and density differentials between saturated water and fresh water, resulting in the attenuation of the driving force governing CO2 diffusion and convection. This leads to a substantial reduction in the rate of CO2 dissolution, primarily governed by gravity-induced fingering, thereby manifesting as a delay in the onset and decay time of convection, accompanied by a pronounced decrement in the maximum Sherwood number. In the field-scale simulation, the injected CO2 improves the reservoir pressure, further pushing more gas to the producers. However, due to the presence of CH4 in the post-injection process, the capacity for CO2 dissolution is reduced. [ABSTRACT FROM AUTHOR]

Gas injection for enhanced oil and gas reservoir recovery is a crucial method in offshore Carbon Capture, Utilization, and Storage (CCUS). The B6 buried hill condensate gas reservoir, characterized by high CO2 content, a deficit in natural energy, developed fractures and low-pressure differentials between formation and saturation pressures, requires supplementary formation energy to mitigate retrograde condensation near the wellbore area through gas injection. However, due to the connected fractures, the B6 gas reservoir exhibits strong horizontal and vertical heterogeneity, resulting in severe gas channeling and a futile cycle, which affects the gas injection efficiency at various levels of fracture development. Based on these findings, we conducted gas injection experiments and numerical simulations on fractured cores. A characterization method for oil and gas relative permeability considering dissolution was established. Additionally, the gas injection development boundary for this type of condensate gas reservoir was quantified according to the degree of fracture development, and the gas injection mode of the B6 reservoir was optimized. Research indicates that the presence of fractures leads to the formation of a dominant gas channel; the greater the permeability difference, the poorer the gas injection effect. The permeability gradation (fracture permeability divided by matrix permeability) in the gas injection area should be no higher than 15; gas injection in wells A1 and A2 is likely to achieve a better development effect under the existing well pattern. Moreover, early gas injection timing and pulse gas injection prove beneficial in enhancing the recovery rate of condensate oil. The study offers significant guidance for the development of similar gas reservoirs and for reservoirs with weakly connected fractures; advancing the timing of gas injection can mitigate the retrograde condensation phenomenon, whereas initiating gas injection after depletion may reduce the impact of gas channeling for reservoirs with strongly connected fractures. [ABSTRACT FROM AUTHOR]

This study investigates the crucial role of Carbon Capture and Storage (CCS) technology in mitigating CO2 emissions from Poland's power systems, which is essential not only for meeting climate targets but also for maintaining energy security in the country. Acknowledging natural gas as a transitional fuel, the focus is on evaluating the decarbonization potential of the natural gas combined cycle (NGCC) power plant. The NGCC with and without an amine-based carbon capture unit was modeled using IPSEpro (SimTech, version 7.0). It was found that the annual CO2 emission from 435.68 MWe (net) NGCC can be reduced from 1,365,501 tons (357.8 kgCO2/MWh) to 136,556 tons (42.9 kgCO2/MWh). On the other hand, the CCS reduced the net electric power of the NGCC from 435.68 MW to 363.47 MW and the net energy efficiency from 55.60% to 46.39%. Nonetheless, these results demonstrate the potential of using the amine-based CO2 capture technology in NGCC systems. This is especially important in the context of the decarbonization of the Polish power system. [ABSTRACT FROM AUTHOR]

Hydrogen is an industrial raw material both for the production of chemicals and for oil refining with hydrotreating. It is the subject of increasing attention for its possible use as an energy carrier and as a flexible energy storage medium. Its production is generally accomplished in Steam Methane Reforming (SMR) plants, where a gaseous mixture of CO and H2, with a limited number of other species, is obtained. The process of production and purification generates relevant amounts of carbon dioxide, which needs to be removed due to downstream process requirements or to limit its emissions to the atmosphere. A work by IEAGHG focused on the study of a state-of-the-art Steam Methane Reforming plant producing 100 kNm3/h of H2 and considered chemical absorption with MethylDiEthanolAmine (MDEA) solvent for removing carbon dioxide from the PSA tail gas in a baseline scheme composed of the absorber, one flash vessel and the regeneration column. This type of process is characterized by high energy consumption, in particular at the reboiler of the regeneration column, usually operated by employing steam, and modifications to the baseline scheme can allow for a reduction of the operating costs, though with an increase in the complexity of the plant. This work analyses three configurations of the treatment section of the off gas obtained after the purification of the hydrogen stream in the Pressure Swing Adsorption unit with the aim of selecting the one which minimizes the overall costs so as to further enhance Carbon Capture and Storage in non-power industries as well. [ABSTRACT FROM AUTHOR]

Even though the energy penalties and solvent regeneration costs associated with amine-based absorption/stripping systems are important challenges, this technology remains highly recommended for post-combustion decarbonization systems given its proven capture efficacy and technical maturity. This study introduces a novel centralized and decentralized hybrid control strategy for the post-combustion carbon capture plant, aimed at mitigating main disturbances and sustaining high system performance. The strategy is rooted in a comprehensive mathematical model encompassing absorption and desorption columns, heat exchangers and a buffer tank, ensuring smooth operation and energy efficiency. The buffer tank is equipped with three control loops to finely regulate absorber inlet solvent solution parameters, preventing disturbance recirculation from the desorber. Additionally, a model-based controller, utilizing the model predictive control (MPC) algorithm, maintains a carbon capture yield of 90% and stabilizes the reboiler liquid temperature at 394.5 K by manipulating the influent flue gas to the lean solvent flowrates ratio and the heat duty of the reboiler. The hybrid MPC approach reveals efficiency in simultaneously managing targeted variables and handling complex input–output interactions. It consistently maintains the controlled variables at desired setpoints despite CO2 flue gas flow disturbances, achieving reduced settling time and low overshoot results. The hybrid control strategy, benefitting from the constraint handling ability of MPC, succeeds in keeping the carbon capture yield above the preset minimum value of 86% at all times, while the energy performance index remains below the favorable value of 3.1 MJ/kgCO2. [ABSTRACT FROM AUTHOR]

Carbon capture, utilization, and storage (CCUS) technology has emerged as a pivotal measure in mitigating global climate change. Notably, CO2-EOR is esteemed for its dual function of sequestering CO2 and enhancing oil recovery. However, this process presents challenges related to asphaltene deposition during CO2 flooding, leading to reservoir damage, such as pore plugging. This study systematically manipulated the factors inducing CO2-induced asphaltene deposition, elucidating the mechanisms and magnitudes of asphaltene precipitation. Additionally, the study investigated the efficacy of carbon quantum dots (CQDs) in mitigating asphaltene deposition. Experimental findings indicated a positive correlation between asphaltene deposition and level of asphaltene content, CO2 injection ratio, and temperature. Moreover, with an increase in experimental pressure, the asphaltene deposition rate demonstrated an initial increase followed by a subsequent decline. Leveraging their favorable compatibility with asphaltene, CQDs effectively suppressed the aggregation behavior of asphaltene. In the presence of CQDs, the onset of asphaltene precipitation was delayed from 45 V% to 55 V%, with the highest inhibition rate reaching approximately 36% at an optimal CQD concentration of 20 mg/L. This study proposes a novel approach to address asphaltene deposition issues in CO2-EOR processes, contributing to the enhancement of recovery rates in low-permeability reservoirs. [ABSTRACT FROM AUTHOR]

Bioenergy with carbon capture and storage (BECCS) or utilization (BECCU) allows net zero or negative carbon emissions and can be a breakthrough technology for climate change mitigation. This work consists of an energetic, exergetic, and economic analysis of an integrated process based on chemical looping combustion of solar-torrefied agro-industrial residues, followed by methanation of the concentrated CO2 stream with green H2. Four agro-industrial residues and four Italian site locations are considered. Depending on the considered biomass, the integrated plant processes about 18–93 kg h−1 of raw biomass and produces 55–70 t y−1 of synthetic methane. Global exergetic efficiencies ranged within 45–60% and 67–77% when neglecting and considering, respectively, the valorization of torgas. Sugar beet pulp and grape marc required a non-negligible input exergy flow for the torrefaction, due to the high moisture content of the raw biomasses. However, for these biomasses, the water released during drying/torrefaction and CO2 methanation could be recycled to the electrolyzer to eliminate external water consumption, thus allowing for a more sustainable use of water resources. For olive stones and hemp hurd, this water recycling brings, instead, a reduction of approximately 65% in water needs. A round-trip electric efficiency of 28% was estimated assuming an electric conversion efficiency of 40%. According to the economic analysis, the total plant costs ranged within 3–5 M€ depending on the biomass and site location considered. The levelized cost of methane (LCOM) ranged within 4.3–8.9 € kgCH4−1 but, if implementing strategies to avoid the use of a large temporary H2 storage vessel, can be decreased to 2.6–5.3 € kgCH4−1. Lower values are obtained when considering hemp hurd and grape marc as raw biomasses, and when locating the PV field in the south of Italy. Even in the best scenario, values of LCOM are out of the market if compared to current natural gas prices, but they might become competitive with the introduction of a carbon tax or through government incentives for the purchase of the PV field and/or electrolyzer. [ABSTRACT FROM AUTHOR]

Conventional Carbon Capture and Storage (CCS) operations use the direct injection of CO2 in a gaseous phase from the surface as a carbon carrier. Due to CO2 properties under reservoir conditions with lower density and viscosity than in situ brine, CO2 flux is mainly gravity-dominated. CO2 moves toward the top and accumulates below the top seal, thus reinforcing the risk of possible leakage to the surface through unexpected hydraulic paths (e.g., reactivated faults, fractures, and abandoned wells) or in sites without an effective sealing caprock. Considering the risks, the potential benefits of the interplay between CO2 and an aqueous solution of formate ions (HCOO¯) were evaluated when combined to control CO2 gravity segregation in porous media. Three combined strategies were evaluated and compared with those where either pure CO2 or a formate solution was injected. The first strategy consisted of a pre-flush of formate solution followed by continuous CO2 injection, and it was not effective in controlling the vertical propagation of the CO2 plume. However, the injection of a formate solution slug in a continuous or alternated way, simultaneously with the CO2 continuous injection, was effective in slowing down the vertical migration of the CO2 plume and keeping it permanently stationary deeper than the surface depth. [ABSTRACT FROM AUTHOR]

Carbon dioxide capture and storage (CCS) is a necessary requirement for high-emitting CO2 industries to significantly reduce volumes of greenhouse gases released into the atmosphere and mitigate climate change. Geological CO2 storage into depleted oil and gas fields is the fastest and most accessible option for CCS deployment allowing for re-purposing existing infrastructures and utilizing significant knowledge about the subsurface acquired during field production operations. The location of such depleted fields in the neighborhoods of high-emitting CO2 industries is an additional advantage of matured on-shore European fields. Considering these advantages, oil and gas operators are now evaluating different possibilities for CO2 sequestration projects for the fields approaching end of production. This article describes an integrated approach to reservoir simulations focused on evaluating a CO2 injection pilot at one of these matured fields operated by MND and located in the Czech Republic. The CO2 injection site in focus is a naturally fractured carbonate reservoir. This oil-bearing formation has a gas cap and connection to a limited aquifer and was produced mainly by pressure depletion with limited pressure support from water injection. The article summarizes the results of the efforts made by the multi-disciplinary team. An integrated approach was developed starting from geological modeling of a naturally fractured reservoir, integrating the results of laboratory studies and their interpretations (geomechanics and geochemistry), dynamic field data analysis (pressure transient analysis, including time-lapse) and history matching reservoir model enabling simulation of the pilot CO2 injection. The laboratory studies and field data analysis provided descriptions of stress-sensitive fracture properties and safe injection envelope preventing induced fracturing. The impact of potential salt precipitation in the near wellbore area was also included. These effects are considered in the context of a pilot CO2 injection and addressed in the reservoir simulations of injection scenarios. Single-porosity and permeability reservoir simulations with a dominating fracture flow and black-oil formulation with CO2 simulated as a solvent were performed in this study. The arguments for the choice of the simulation approach for the site in focus are shortly discussed. The reservoir simulations indicated a larger site injection capacity than that required for the pilot injection, and gravity-driven CO2 migration pathway towards the gas cap in the reservoir. The application of the approach to the site in focus also revealed large uncertainties, related to fracture description and geomechanical evaluations, resulting in an uncertain safe injection envelope. These uncertainties should be addressed in further studies in preparation for the pilot. The article concludes with an overview of the outcomes of the integrated approach and its application to the field in focus, including a discussion of the issues and uncertainties revealed. [ABSTRACT FROM AUTHOR]

Climate change necessitates urgent actions to mitigate carbon dioxide (CO2) emissions from fossil fuel-based energy generation. Among various strategies, the deployment of carbon capture and storage (CCS) solutions is critical for reducing emissions from point sources such as power plants and heavy industries. In this context, cryogenic carbon capture (CCC) via desublimation has emerged as a promising technology. While CCC offers high separation efficiency, minimal downstream compression work, and integration potential with existing industrial processes, challenges such as low operating temperatures and equipment costs persist. Ongoing research aims to address these hurdles in order to optimize the desublimation processes for widespread implementation. This review consolidates diverse works from the literature, providing insights into the strengths and limitations of CCC technology, including the latest pilot plant scale demonstrations. The transformative potential of CCC is first assessed on a theoretical basis, such as thermodynamic aspects and mass transfer phenomena. Then, recent advancements in the proposed process configurations are critically assessed and compared through key performance indicators. Furthermore, future research directions for this technology are clearly highlighted. [ABSTRACT FROM AUTHOR]

In this study, a novel system which integrates solar thermal energy with membrane gas absorption technology is proposed to capture CO2 from a 580 MWe pulverized coal power plant. Technical feasibility and economic evaluation are carried out on the proposed system in three cities with different solar resources in China. Research results show that the output capacity and net efficiency of the SOL-HFMC power plant are significantly higher than those of the reference power plant regardless of whether a TES system is applied or not. In addition, the CEI of the SOL-HFMC power plant with the TES system is 4.36 kg CO2/MWh, 4.45 kg CO2/MWh and 4.66 kg CO2/MWh lower than that of the reference power plant. The prices of the membrane, vacuum tube collector and phase change material should be reduced to achieve lower LCOE and COR values. Specifically for the SOL-HFMC power plant with the TES system, the corresponding vacuum tube collector price shall be lower than 25.70 $/m2 for Jinan, 95.20 $/m2 for Xining, and 128.70 $/m2 for Lhasa, respectively. To be more competitive than a solar-assisted ammonia-based post-combustion CO2 capture power plant, the membrane price in Jinan, Xining and Lhasa shall be reduced to 0.012 $/m, 0.015 $/m and 0.016 $/m for the sake of LCOE, and 0.03 $/m, 0.033 $/m and 0.034 $/m for the sake of COR, respectively. [ABSTRACT FROM AUTHOR]

The increase in emissions and concentration of carbon dioxide in the atmosphere necessitates the implementation of direct carbon dioxide capture technologies. The article presents the characteristics of a single-stage membrane unit for the direct capture of carbon dioxide from the air. A membrane with a selectivity of α C O 2 / N 2 = 70 and permeability P C O 2 = 108 m 3 (S T P) (m 2 · h · b a r) is chosen as the reference variant. It is demonstrated that increasing the pressure difference in the system by reducing the pressure of the permeate stream results in an improvement of all analyzed parameters. Manipulating both the membrane surface and its CO2 permeability yields similar results. With an increase in permeability or membrane surface area, the proportion of CO2 in the retentate and permeate decreases, while the degree of carbon dioxide recovery increases. However, the energy intensity of the process is a complex issue due to the presence of a local minimum in the obtained characteristics. Therefore, a relationship between the constants of energy intensity values for the separation process on the surface area field and CO2 membrane permeability is presented. The minimum energy intensity of the process obtained is 22.5 k W h / k g C O 2 . The CO2 content in the retentate for all analyses did not exceed 280 ppm. [ABSTRACT FROM AUTHOR]