Search

In this paper, the effect of solar intensity on the heat pipe tip temperature in a heat pipe type—evacuated-tube solar collector (HP-ETSC) was investigated. A simple relation was proposed, relating the solar intensity to the heat pipe tip temperature generated from the experimental data. This simple empirical relation was applied in a set of heat transfer equations derived to predict the heating medium temperature at the manifold outlet of the evacuated-tube solar collector. The calculated results corresponding to two types of heating medium, i.e., palm oil and water, were compared with experimental results from the literature. The results show that the average error was 6.41% for the case of palm oil and 4.66% for the case of water. Based on the case of water as a heating medium fluid, it was found that the flow rate of the heating medium fluid affected the accuracy of prediction, as the percentage error increased with the heating medium flow rate. The maximum percentage error increased from only 1.83% for a water inlet flowing at a Reynolds number of about 2.4 × 103 to 15.23% for a water flow rate at a Reynolds number of about 2.6 × 104. The correction factor was added into the correlation to predict the heat transfer coefficients of heating medium fluids. With this correction factor, the maximum error could be reduced from 11.78% to 7.29% for the palm oil case and from 15.23% to 5.57% for the water case. The average errors corresponding to palm oil and water cases could be reduced to 0.74% and 1.26%, respectively. [ABSTRACT FROM AUTHOR]

The cooling system is the auxiliary equipment that consumes the most energy in a data center, accounting for about 30 to 50% of the total energy consumption. In order to effectively reduce the energy consumption of a data center, it is very important to improve the heat exchange efficiency at the chip level. Compared with air cooling, single-phase cold plate liquid cooling, and immersion liquid cooling, the flat loop heat pipe (FLHP) is considered to be a better chip-level cooling solution for data centers. It has extremely high heat transfer efficiency and heat flux variability, and it can avoid the operation risk caused by liquid entering the server. In this paper, a FLHP with an evaporator designed with a "Tesla valve" flow channel configuration is developed. Experiments on the FLHP are carried out, focusing on the installation angles and cooling condition factors. The results show that an inclination angle of 20° is the critical point of the influence of gravity on the performance of the FLHP; to ensure good operation of the FLHP, the installation angle should be greater than 20°. The equivalent heat transfer coefficients of the FLHP condenser under different cooling conditions are calculated. It is found that water cooling can provide higher cooling heat transfer coefficients with lower energy consumption and operating noise. Additionally, the heat transfer limit, operating temperature uniformity, and start-up stability of the FLHP are significantly improved under water cooling conditions. The maximum heat load of the FLHP is up to 230 W, and the temperature difference of the evaporator surface can be controlled within 0.5 °C, under 20 °C water cooling. Finally, using the FLHP for thermal management of the chip, its heat transfer efficiency is 166 and 41% higher than that of air cooling and water cooling, respectively. [ABSTRACT FROM AUTHOR]

This paper proposes a methodology aiming at determining the most influent working variables and geometrical parameters over the pressure drop and heat transfer during the condensation process of several refrigerant gases using heat exchangers with pipes mini channels technology. A multi-criteria decision making (MCDM) methodology was used; this MCDM includes a mathematical method called SIMUS (Sequential Interactive Modelling for Urban Systems) that was applied to the results of 2543 tests obtained by using a designed refrigeration rig in which five different refrigerants (R32, R134a, R290, R410A and R1234yf) and two different tube geometries were tested. This methodology allows us to reduce the computational cost compared to the use of neural networks or other model development systems. This research shows six variables out of 39 that better define simultaneously the minimum pressure drop, as well as the maximum heat transfer, saturation pressure fluid entering the condenser being the most important one. Another aim of this research was to highlight a new methodology based on operation research for their application to improve the heat transfer energy efficiency and reduce the CO2 footprint derived of the use of heat exchangers with minichannels. [ABSTRACT FROM AUTHOR]

Coolants are widely used to dissipate grinding heat in conventional grinding. This process, however, is not satisfactory as coolants often lose efficacy in grinding due to film boiling and can result in adverse health and environment effects. The present paper put forward the concept of a rotating heat pipe grinding wheel, attempting to reduce or eliminate the coolant amount and realize green machining. The heat transfer performance of rotating heat pipe grinding wheel was studied by using volume of fluid method in ANSYS/FLUENT. The influence of the input heat flux, filling ratio and rotational speed were investigated by a simulation method. Results show that the appropriate heat flux range for the rotating heat pipe grinding wheel was from 2000 to 100,000 W/m2, the ideal filling ratio was 50% and the rise of the rotational speed turned out to weaken the heat transfer coefficient. Finally, dry grinding experiments on Ti-6Al-4V were performed and the temperatures in both the rotating heat pipe and the grinding contact zone were monitored. The new designed rotating heat pipe grinding wheel showed a good prospect for application to green grinding of difficult-to-cut materials. [ABSTRACT FROM AUTHOR]