Search

This article presents a novel mixed-thermoelastohydrodynamic (TEHD) model for the lateral lubricating interfaces which exist between floating lateral bushings and gears in external gear machines (EGMs). The proposed model integrates the influence of surface asperities along with the fluid structure and thermal interaction in the interface, especially in the regions of very low film thicknesses by following a stochastic approach in modelling the mixed lubrication regime. Furthermore, the current work includes validation of the predictions of the mixed-TEHD model against experimentally measured leakages from the lateral gap and compares the performance of this model with a previously developed full film TEHD model for the lateral gaps in EGMs. [ABSTRACT FROM AUTHOR]

This paper presents an experimental and numerical modal analysis for an external gear pump considering its mounting on a test rig in a laboratory setting. Most of the previous studies on experimental modal analysis (EMA) of hydraulic pumps focused on the modal frequencies to allow model validation. However, the mode shapes of pump bodies have not extensively been discussed. Furthermore, the nature of the pump components assembly and mounting poses some modeling challenges, such as the uncertain material properties of each component, the behavior of the bolted joints, and some critical modeling boundary conditions related to pump mounting. In this regard, the experimentally obtained vibration modes of a reference pump using the least-square complex exponential (LSCE) method are analyzed with an emphasis on the characteristics of the mode shapes. Then, simple modeling strategies are proposed and validated by performing the analysis from the component level to the full assembly. As a result, the mode shapes are categorized depending on the type of motions that the modes exhibit. It is observed that the pump casing does not show any substantial deformation but is close to the rigid body motion. Moreover, without considerably increasing model complexities, the proposed numerical approach provides reasonable accuracy with average errors in modal frequencies of 6%, as well as good agreement in terms of mode shapes. The vibration reduction strategy is briefly discussed based on the measured mode shapes, and the proposed modeling approaches can be useful to study external gear pumps with minimal model complexities yet allowing reasonable result accuracy. [ABSTRACT FROM AUTHOR]

This paper presents the experimental characterization of the vibroacoustic fields and the evaluation of noise performances of hydraulic pumps. Research on hydraulic pump noise has traditionally focused on the fluid-borne noise sources, and very often the analyses of vibration and noise have been performed focusing on a few local points. This trend results in the lack of investigation on the overall behaviors of vibroacoustic fields of hydraulic pumps, and it has been one of the obstacles to understand the complete mechanisms of noise generation. Moreover, despite the existence of the ISO standards for the determination of noise levels, diverse metrics have been used for the evaluation of noise performances of the pumps, but the adequacy of these metrics has not been carefully examined. In this respect, this paper aims at introducing a way to characterize and interpret the measured vibroacoustic field and providing proper methods which are also capable of applying the ISO standards for the fair assessment of pump noise performances. For the characterization of the vibroacoustic field, operational deflection shapes (ODS) and corresponding radiated sound fields are visualized at harmonics of the pumping frequency by using a spectral analysis. Observations are made regarding the motions of the pump and its mounting plate and the resultant radiated noise, depending on the frequency, as well as their correlation. A numerical analysis using the Rayleigh integral equation is also performed to further investigate the contribution of the mounting plate motion on the noise radiation. For the evaluation of noise performance, two different units are tested at multiple operating conditions, and comparisons are made based on their measured sound power levels (SWLs) and sound pressure levels (SPLs). The results emphasize the importance of SWL measurement for the fair noise performance evaluation, and the two methods are proposed as practices to determine the minimum number of measurement points for practicability and to have reliable sound power determination for hydraulic pumps. [ABSTRACT FROM AUTHOR]

The flow of energy within external gear machines (EGMs) leads to the variation of fluid temperature in the EGMs, which affects their performance. However, the common approaches for the simulation of EGMs assume isothermal conditions. This isothermal assumption negatively impacts their modelling accuracy in terms of the internal flows which are dependent on the fluid temperature (via fluid properties). This paper presents a lumped parameter based thermal model of EGMs where the fluid temperature in the EGM is evaluated considering the effects of compression/expansion, internal flows, and power losses. Further, numerical techniques are developed to model each of these three aspects. The thermal model is validated via the outlet temperature and volumetric efficiency measurements obtained from experiments conducted on six units of an EGM taken as a reference with different internal clearances. The results from the model show that the fluid temperature increases as it is carried from the inlet side to the outlet side during the pumping operation. However, the fluid at the ends of the shafts has the highest temperature. By comparing the isothermal simulation results with the proposed thermal model, the results also point out how the isothermal assumption becomes inaccurate, particularly in conditions of low volumetric efficiency. [ABSTRACT FROM AUTHOR]

External gear pumps are among the most popular fluid power positive displacement pumps, however they often suffer of excessive flow pulsation transmitted to the downstream circuit. To meet the increasing demand of quiet operation for modern fluid power system, a better understanding of the ripple source of gear pumps is desirable. This paper presents a novel approach for the analysis of the ripple source of gear pumps based on decomposition into a kinematic component and a pressurization component. The pump ripple can be regarded as the superposition of the displacement solution and the pressurization solution. The displacement solution is driven by the kinematic flow, and it can be derived from the kinematic flow theory; instead, the pressurization solution can be approximated by overlapping the pressurization flow for a single displacement chamber. Furthermore, in this way the changes of these two components with modification of the delivery circuit are determined in both analytical and numerical ways. The result of this analysis provides a good interpretation of the pulsation simulated by a detailed lumped-parameter simulation model, thus showing its validity. The result also indicates that the response of two ripple sources to the change of the loading in the downstream hydraulic circuit is very different. These findings reveal the limitation of the traditional experimental method for determining the pump ripple, that new experimental methods which are more physics-based can be potentially formulated based on this work. [ABSTRACT FROM AUTHOR]