Search

High-energy-density compounds such as norbornadiene (NBD) are being considered as potential cost-effective fuel additives, or partial replacements, for high-speed propulsion applications. To assess the ability of NBD to influence basic fuel reactivity enhancement and to build a database for developing future NBD kinetics models, ignition delay times were measured in two shock-tube facilities at Texas A&M University for H2/O2, CH4/O2, H2/NBD/O2, and CH4/NBD/O2 mixtures (ϕ = 1) that were highly diluted in argon. The reflected-shock temperatures ranged from 1014 to 2227 K, and the reflected-shock pressures remained near 1 atm for all of the experiments, apart from the hydrogen mixtures, which were also tested near 7 atm, targeting the second-explosion limit. The molar concentrations of NBD were supplemented to the baseline mixtures representing 1–2% of the fuel by volume. A chemiluminescence diagnostic was used to track the time history of excited hydroxyl radical (OH*) emission, which was used to define the ignition delay time at the sidewall location. Spectroscopic CO data were also obtained using a tunable quantum cascade laser to complement both the ignition and the chemiluminescence data. The CH4/O2 mixtures containing NBD demonstrated reduced ignition delay times, with a pronounced effect at lower temperatures. Conversely, this additive increased the ignition delay time dramatically in the H2/O2 mixture, which was attributed to changes in the fundamental chemistry with the introduction of molecules containing carbon bonds, which require stronger activation energies for ignition. Correlations were developed to predict the ignition delay time, which depends on species concentration, temperature, and pressure. Additionally, one tentative mechanism was tested, combining base chemistry from NUIGMech 1.1 with pyrolysis and oxidation reactions for NBD using the recent efforts from experimental and theoretical literature studies. The numerical predictions show that the rapid decomposition of NBD provides a pool of active H-radicals, significantly increasing the reactivity of methane. This study represents the first set of gas-phase ignition and CO time-history data measured in a shock tube for hydrogen and methane mixtures containing the additive NBD. [ABSTRACT FROM AUTHOR]

Isopropanol has potential as a future bio-derived fuel and is a promising substitute for ethanol in gasoline blends. Even so, little has been done in terms of high-temperature chemical kinetic speciation studies of this molecule. To this end, experiments were conducted in a shock tube using simultaneous CO and H2O laser absorption measurements. Water and CO formation during isopropanol pyrolysis was also examined at temperatures between 1127 and 2162 K at an average pressure of 1.42 atm. Species profiles were collected at temperatures between 1332 and 1728 K and at an average pressure of 1.26 atm for equivalence ratios of 0.5, 1.0, and 2.0 in highly diluted mixtures of 20% helium and 79.5% argon. Species profiles were also compared to four modern C3 alcohol mechanisms, including the impact of recent rate constant measurements. The Li et al. (2019) and Saggese et al. (2021) models both best predict CO and water production under pyrolysis conditions, while the AramcoMech 3.0 and Capriolo and Konnov models better predict the oxidation experimental profiles. Additionally, previous studies have collected ignition delay time (τign) data for isopropanol but are limited to low pressures in highly dilute mixtures. Therefore, real fuel–air experiments were conducted in a heated shock tube with isopropanol for stoichiometric and lean conditions at 10 and 25 atm between 942 and 1428 K. Comparisons to previous experimental results highlight the need for real fuel–air experiments and proper interpretation of shock-tube data. The AramcoMech 3.0 model over predicts τign values, while the Li et al. model severely under predicts τign. The models by Capriolo and Konnov and Saggese et al. show good agreement with experimental τign values. A sensitivity analysis using these two models highlights the underlying chemistry for isopropanol combustion at 25 atm. Additionally, modifying the Li et al. model with a recently measured reaction rate shows improvement in the model's ability to predict CO and water profiles during dilute oxidation. Finally, a regression analysis was performed to quantify τign results from this study. [ABSTRACT FROM AUTHOR]