Search

The working temperature affects the performance of PEMFC, so a reasonable and efficient cooling channel is necessary to control the working temperature in an efficient area. In this study, the channel structure of the bipolar plate for PEMFC is analyzed using the FLUENT simulation calculation method. The influence of cell size and cooling water flow direction on cell temperature distribution is analyzed, including an examination of the channel ridge width, depth, and aspect ratio of the bipolar plate. After comparing and analyzing three ridge width sizes (0.5 mm, 1.5 mm and 2 mm) in the paper, it was found that a ridge width of 2 mm had the best heat transfer performance. And it was found that a groove depth of 0.5 mm had the best heat transfer performance when comparing three groove depth dimensions (0.5 mm, 1 mm and 1.5 mm). The aspect ratio size parameters had almost no effect on the maximum and average temperatures of the electric stacks, while the relative flow direction of cooling water had a great influence on the temperature distribution of the bipolar plate. [ABSTRACT FROM AUTHOR]

The proton exchange membrane fuel cell (PEMFC) is a promising energy conversion device due to its high reliability, fast response speed, and low pollutant emission. However, the reality of its commercial application requires further cost reduction and efficiency improvement. The material distribution in the channel and the performance of PEMFC can be improved by setting the boss inside the flow channels. In this paper, the performance of PEMFC with the boss in flow channels in a parallel flow field was analyzed by simulation. The influence of different boss arrangements and heights on gas pressure drop, distribution uniformity, gas component distribution, temperature distribution, and output performance of the fuel cell were analyzed in detail. The bosses would increase the pressure drop and the distribution uniformity of reactive gases in flow channels significantly. The cross-arrangement of bosses is better than the cross-arrangement of bosses and juxtaposition according to increasing performance and pressure drop. The cross-arrangement with a boss height of 0.4 mm is suitable for the parallel flow field in this paper. The improved scheme of flow channel design is proposed to provide a reference for fuel cells for subsequent research. [ABSTRACT FROM AUTHOR]

The hydrogen supply system is one of the important components of a hydrogen fuel cell engine, and its performance has an important impact on the economy and power of the engine system. In this paper, a hydrogen supply system based on cyclic mode is designed for a hydrogen fuel cell stack with a full load power of 150 kW, and the corresponding hydrogen fuel cell engine simulation model is built and validated. The control strategy of the fuel cell hydrogen supply system is developed, and its effect is verified through bench tests. The results show that the developed control strategy can keep the volume fraction of nitrogen below 6%, the hydrogen excess ratio does not exceed 1.5 under medium and high operating conditions, the anode pressure is relatively stable, and the stack can operate efficiently and reliably. [ABSTRACT FROM AUTHOR]

The assembly consistency of a diesel engine will affect its nitrogen oxides (NOx) emission variation. In order to improve the NOx emissions of diesel engines, a study was carried out based on the assembly tolerance variation of the diesel engine's combustion system. Firstly, a diesel engine which meets the Euro VI standards together with the experimental data is obtained. The mesh model and combustion model of the engine combustion system are built in the Converge software (version 2.4, Tecplot, Bellevue, DC, USA), and the experimental data is used to calibrate the combustion model obtained in the Converge software. Then, the four-factor and three-level orthogonal simulation experiments are carried out on the dimension parameters that include nozzle extension height, throat diameter, shrinkage diameter and combustion chamber depth. Through mathematical analysis on the experimental data, the results show that the variation of nozzle extension height and combustion chamber depth have a strong influence on NOx emission results, and the variation of combustion chamber diameter also has a weak influence on NOx production. According to the regression model obtained from the analysis, there is a quadratic function relating the nozzle extension height and NOx emissions and the amount of NOx increases with increasing nozzle extension height. The relationship between emission performance and size parameters is complex. In the selected size range, the influence of the variation of the chamber diameter on NOx is linear. The variation of the chamber depth also has an effect on NOx production, and the simulation results vary with the change of assembly tolerance variation. Thus, in the engine assembly process, it is necessary to strictly control the nozzle extension height and combustion chamber depth. The research results are useful to improve the NOx emission of diesel engine and provide a basis for the control strategy of selective catalytic reduction (SCR) devices. [ABSTRACT FROM AUTHOR]