Search

The Renewable Energy Directive II introduces renewable energy communities, enhancing energy sharing. However, many existing initiatives, focussing only on electricity, overlook the substantial energy demand in building sector comprising residential and commercial spaces. Energy communities in this sector can leverage district heating and cooling technology for thermal energy sharing, contributing to carbon neutrality by enhancing efficiency and reducing primary energy usage. Advanced strategies such as integrating renewables into heating and cooling grids, sector coupling, and utilising waste heat are key in moving away from fossil fuels. The Campania Region (Italy), abundant in geothermal energy potential, chose a district in which to implement the GeoGRID system. This innovative setup combines a four-pipe district heating and cooling network with an Organic Rankine Cycle plant, tapping into geothermal energy from the Solfatara area. The geothermal fluid's heat feeds the ORC evaporator and then powers the thermal network, allowing direct heating and domestic hot water supply during winter. A thorough techno-economic analysis assessed the energy potential extractable from the geothermal fluid. Crucial aspects of this study are the evaluation of the energy and environmental efficiency of the system within the renewable energy community framework. Additionally, the paper introduces a methodology applicable for assessing geothermal energy communities on a global scale. [ABSTRACT FROM AUTHOR]

In Europe, the recast of Directive 2018/2001 defined Renewable Energy Communities as innovative configurations for renewable energy sharing between different end user types. In this regard, this work aims to assess the benefits following the constitution of a Renewable Energy Community in the industrial area of Benevento (South of Italy), involving a mixed-use building and an industrial wastewater treatment plant. The alternative single end users' configuration has been also examined, and both solutions have been compared with the current state where the users' electric energy requests are fully met by the power grid. The users have been equipped with a 466 kWp photovoltaic plant, modelled in HOMER Pro®, providing in input experimental meteorological data (global solar radiation and air temperature) collected by one of the weather control units in Benevento. Real data about users' electric energy demand have been gathered from their electricity bills, and when unavailable their electric load profiles on an hourly basis have been reconstructed based on the aggregated monthly data. Energy sharing has been proven to increase energy self-consumption and the users' self-sufficiency. Annually, the primary energy demand is reduced by 577 MWh (1.2 MWh/kWp), carbon dioxide emissions by 84 tCO2 and operative costs by 101 kEUR. [ABSTRACT FROM AUTHOR]

Renewable energy communities are catalysts of social innovation, the citizens' engagement in energy actions, and the exploitation of local resources. Thus, this paper defines a model for analyzing and optimally sizing energy systems serving renewable energy communities. Then, the proposed and replicable model was tailored to the economic feasibility analysis of a renewable energy community in the municipality of Tirano (Northern Italy). An energy audit was carried out to identify the electricity production and consumption within the perimeter of the primary substation and the thermal energy demand of the existing district heating network. The technical features of the energy conversion systems serving the renewable energy community were determined: an organic Rankine cycle biomass-based cogeneration plant, a mini-hydro plant, and a distributed photovoltaic system. Moreover, several different scenarios have been identified, in terms of cogeneration operating mode, photovoltaic penetration, and thermal energy economic value. The results show that, moving from 4.22 MW to 5.22 MW of photovoltaic peak power, the annual renewable electricity production increases by 10.1%. In particular, the simple pay back ranges between 4.90 and 4.98 years and the net present value between EUR 12.4 and 13.3 M for CHP operating at full power mode, considering that thermal energy available from the cogeneration unit is sold at EUR 49.2/MWh. These outcomes demonstrate the economic feasibility of wood-biomass-based renewable energy communities, which may help to enlarge the contribution of renewable technologies other than photovoltaic. [ABSTRACT FROM AUTHOR]

A hybrid solar-assisted trigeneration system is analyzed in this paper. The system is composed of a 20 m² solar field of evacuated tube collectors, a natural gas fired micro combined heat and power system delivering 12.5 kW of thermal power, an absorption heat pump (AHP) with a nominal cooling power of 17.6 kW, two storage tanks (hot and cold) and an electric auxiliary heater (AH). The plant satisfies the energy demand of an office building located in Naples (Southern Italy). The electric energy of the cogenerator is used to meet the load and auxiliaries electric demand; the interactions with the grid are considered in cases of excess or over requests. This hybrid solution is interesting for buildings located in cities or historical centers with limited usable roof surface to install a conventional solar heating and cooling (SHC) system able to achieve high solar fraction (SF). The results of dynamic simulation show that a tilt angle of 30° maximizes the SF of the system on annual basis achieving about 53.5%. The influence on the performance of proposed system of the hot water storage tank (HST) characteristics (volume, insulation) is also studied. It is highlighted that the SF improves when better insulated and bigger HSTs are considered. A maximum SF of about 58.2% is obtained with a 2000 L storage, whereas the lower thermal losses take place with a better insulated 1000 L tank. [ABSTRACT FROM AUTHOR]

The highest economic costs of a geothermal plant are basically related to well drilling and heat exchanger maintenance cost due to the chemical aggressiveness of geothermal fluid. The possibility to reduce these costs represents an opportunity to push toward geothermal plants development. Such challenges are even more important in the sites with a low-medium temperature geothermal fluids (90–120 °C) availability, where the use of these fluids for direct thermal uses can be very advantageous. For this reason, in this study, a direct geothermal heating system for a building will be investigated by considering a plastic plate heat exchanger. The choice of a polymeric heat exchanger for this application is upheld by its lower purchase cost and its higher fouling resistance than the common metal heat exchangers, overcoming the economic issues related to conventional geothermal plant. Thus, the plastic plate heat exchanger was, firstly, geometrical and thermodynamical modeled and, after, exergoeconomic optimized. In particular, an exergoeconomic analysis was assessed on the heat exchanger system by using a MATLAB and REFPROP environment, that allows for determination of the exergoeconomic costs of the geothermal fluid extraction, the heat exchanger, and the heating production. A sensitivity analysis was performed to evaluate the effect of main design variable (number of plates/channels) and thermodynamic variable (inlet temperature of geothermal fluid) on yearly exergoeconomic product cost. Then, the proposed methodology was applied to a case study in South of Italy, where a low-medium enthalpy geothermal potential exists. The plate-heat exchanger was used to meet the space heating requests of a single building by the exploitation of low-medium temperature geothermal fluids availability in the selected area. The results show that the inlet temperature of geothermal fluid influences the exergoeconomic cost more than the geometrical parameter. The variation of the exergoeconomic cost of heat exchanger with the inlet geothermal fluid temperature is higher than the change of the exergoeconomic costs associated to wells drilling and pumping with respect to the same variable. This is due the fact that, in the selected zone of South of Italy, it is possible to find geothermal fluid in the temperature range of 90–120 °C, at shallow depth. The product exergoeconomic cost is the lowest when the temperature is higher than 105 °C; thus, the smallest heat exchange area is required. The exergoeconomic optimization determines an optimum solution with a total product cost of 922 €/y for a temperature of geothermal fluid equal to 117 °C and with a number of plates equal to 15. [ABSTRACT FROM AUTHOR]

Gas engine-driven heat pumps are an interesting option to satisfy space heating and cooling demands aiming at energy saving, environmental impact and operating costs' reduction. This work presents (i) a comprehensive review updated on gas engine-driven heat pumps research activities, (ii) the investigation of the central role of this technology in the air conditioning sector and (iii) the future perspectives regarding gas engine heat pumps' diffusion in the context of the energy sector decarbonisation. The outcomes highlight that gas engine heat pumps could have better environmental performance compared to electric heat pumps both in heating and cooling operations. Moreover, they could play a pivotal role in the fight against climate change and energy security since they can guarantee an energy mix differentiation moving from electricity to natural gas and renewable gases' usage. Indeed, by 2030, a lower-carbon gas grid could be supported by renewable gases. A further investigation has concerned diffusion of gas heat pumps activated from biofuels produced by local biomass in an energy community scenario based on a low-temperature energy district network. A novel biomass-based GEHP interacting with a low-temperature district heating network is proposed here. This system could save more than 30% of primary energy compared to biomass-fuelled boilers. [ABSTRACT FROM AUTHOR]

This paper presents a thermodynamic, economic, and environmental analysis of a renewable polygeneration system connected to a district heating and cooling network. The system, fed by geothermal energy, provides thermal energy for heating and cooling, and domestic hot water for a residential district located in the metropolitan city of Naples (South of Italy). The produced electricity is partly used for auxiliaries of the thermal district and partly sold to the power grid. A calibration control strategy was implemented by considering manufacturer data matching the appropriate operating temperature levels in each component. The cooling and thermal demands of the connected users were calculated using suitable building dynamic simulation models. An energy network dedicated to heating and cooling loads was designed and simulated by considering the variable ground temperature throughout the year, as well as the accurate heat transfer coefficients and pressure losses of the network pipes. The results were based on a 1-year dynamic simulation and were analyzed on a daily, monthly, and yearly basis. The performance was evaluated by means of the main economic and environmental aspects. Two parametric analyses were performed by varying geothermal well depth, to consider the uncertainty in the geofluid temperature as a function of the depth, and by varying the time of operation of the district heating and cooling network. Additionally, the economic analysis was performed by considering two different scenarios with and without feed-in tariffs. Based on the assumptions made, the system is economically feasible only if feed-in tariffs are considered: the minimum Simple Pay Back period is 7.00 years, corresponding to a Discounted Pay Back period of 8.84 years, and the maximum Net Present Value is 6.11 M€, corresponding to a Profit Index of 77.9% and a maximum Internal Rate of Return of 13.0%. The system allows avoiding exploitation of 27.2 GWh of primary energy yearly, corresponding to 5.49∙103 tons of CO2 avoided emissions. The increase of the time of the operation increases the economic profitability. [ABSTRACT FROM AUTHOR]

In this paper two solar electric-driven air conditioning systems are compared and analyzed from an energy and environmental point of view. Both systems satisfy the electricity, space heating and cooling needs of an existing multi-purpose, multi-story building that is simulated with TRNSYS 17. The first one, considered as reference system, is based on a centralized electric heat pump coupled with a conventional photovoltaic plant installed 10 years ago. The second one, hereinafter proposed system, has a hybrid configuration, consisting of a ground-source heat pump, a low temperature thermal network and a series of electric heat pumps, one per apartment. In addition, the plant is connected to a high-performance commercial photovoltaic system equipped with a solar tracking system to the panels. Five different solutions realized with vertical, two horizontal orientations, polar and two-axis trackers are taken into account and compared with the standard fixed configuration. The last hybrid configuration can be seen as an upgrade of an existing decentralized air conditioning system in which the local electric heat pumps are converted in water-to-water devices that interact with the thermal grid representing the heat source/sink for them. In both solar electric heating and cooling plants the photovoltaic system is installed on the building roof and it produces electricity to feed the heat pumps and end-users. The electricity surplus or the load not covered by solar field is fed to/taken from power grid. The energy and environmental analyses have been performed by considering both average annual and monthly values of power grid efficiency and CO2 emission factor for electricity. By comparing reference system and proposed one equipped with a two-axis tracker system a primary fossil energy saving of 101.67% is achieved in summer period and 28.10% in winter period. These percentages are the highest values recorded, even if, for all configurations the energy analysis rewards the proposed system. The results of environmental analysis demonstrate that the reference system has the worst performances compared to proposed system with all solar tracker systems selected guarantying positive values for avoided carbon dioxide index up to 45.86%. [ABSTRACT FROM AUTHOR]

Improvements in using geothermal sources can be attained through the installation of power plants taking advantage of low and medium enthalpy available in poorly exploited geothermal sites. Geothermal fluids at medium and low temperature could be considered to feed binary cycle power plants using organic fluids for electricity "production" or in cogeneration configuration. The improvement in the use of geothermal aquifers at low-medium enthalpy in small deep sites favours the reduction of drilling well costs, and in addition, it allows the exploitation of local resources in the energy districts. The heat exchanger evaporator enables the thermal heat exchange between the working fluid (which is commonly an organic fluid for an Organic Rankine Cycle) and the geothermal fluid (supplied by the aquifer). Thus, it has to be realised taking into account the thermodynamic proprieties and chemical composition of the geothermal field. The geothermal fluid is typically very aggressive, and it leads to the corrosion of steel traditionally used in the heat exchangers. This paper analyses the possibility of using plastic material in the constructions of the evaporator installed in an Organic Rankine Cycle plant in order to overcome the problems of corrosion and the increase of heat exchanger thermal resistance due to the fouling effect. A comparison among heat exchangers made of commonly used materials, such as carbon, steel, and titanium, with alternative polymeric materials has been carried out. This analysis has been built in a mathematical approach using the correlation referred to in the literature about heat transfer in single-phase and two-phase fluids in a tube and/or in the shell side. The outcomes provide the heat transfer area for the shell and tube heat exchanger with a fixed thermal power size. The results have demonstrated that the plastic evaporator shows an increase of 47.0% of the heat transfer area but an economic installation cost saving of 48.0% over the titanium evaporator. [ABSTRACT FROM AUTHOR]

Energy systems face great challenges from both the supply and demand sides. Strong efforts have been devoted to investigate technological solutions aiming at overcoming the problems of fossil fuel depletion and the environmental issues due to the carbon emissions. Hybrid (activated by both renewables and fossil fuels) distributed energy systems can be considered a very effective and promising technology to replace traditional centralized energy systems. As a most peculiar characteristic, they reduce the use of fossil sources and transmission and distribution losses along the main power grid and contribute to electric peak shaving and partial-loads losses reduction. As a direct consequence, the transition from centralized towards hybrid decentralized energy systems leads to a new role for citizens, shifting from a passive energy consumer to active prosumers able to produce energy and distribute energy. Such a complex system needs to be carefully modelled to account for the energy interactions with prosumers, local microgrids and main grids. Thus, the aim of this paper is to investigate the performance of a hybrid distributed energy system serving an urban community and modelled within the framework of agent-based theory. The model is of general validity and estimates (i) the layout of the links along which electricity is distributed among agents in the local microgrid, (ii) electricity exchanged among agents and (iii) electricity exported to the main power grid or imported from it. A scenario analysis has been conducted at varying the distance of connection among prosumers, the installed capacity in the area and the usage of links. The distributed energy system has been compared to a centralized energy system in which the electricity requests of the urban community are satisfied by taking electricity from the main grid. The comparison analysis is carried out from an energy, environmental and economic point of view by evaluating the primary energy saving, avoided carbon dioxide emissions and the simple payback period indices. [ABSTRACT FROM AUTHOR]