Search

To initially improve the gas production rate and shorten the payback period for tight gas reservoirs, the multiple-fractured horizontal well (MFHW) model is always applied. However, in the late stages of exploitation, it is difficult to adopt reasonable measures for enhanced gas recovery (EGR), particular for continental sedimentary formation with multiple layers, and efficient strategies for EGR in this type of gas field have not yet been presented. Therefore, in this paper, a typical tight gas reservoir in the late stages of exploitation, the Denglouku gas reservoir in Changling gas field, in which MFHWs were utilized and contributed to the communication of the higher Denglouku formation (0.34 mol% CO2) and lower Yingcheng formation (27 mol% CO2) during hydraulic fracturing, is studied comprehensively. Firstly, alongside the seismic, logging, drilling and experimental data, 3D geological and numerical simulation models are developed. According to the differences in CO2 mole fractions for different formations, the gas production rate of MFHWs produced from Denglouku formation is accurately calculated. Then, the well gas production rate (WGPR) and the well bottom-hole pressure (WBHP) history are matched with the calculated values, and thus the types of remaining gas are provided through the fine reservoir description. Finally, in a combination of gas recovery and economics, the optimal infill well type and the adjustment scheme are determined. The results show that there are three main categories of remaining gas, which are areal distribution, abundant points, and marginal dispersion, and the ratios of reaming gas reserve for these three types are 80.3%, 4.2%, and 15.5%, respectively. For the tight gas reservoir developed by MFHWs with parallel and zipper patterns, the best infilling well type is the vertical well. The combination of patching holes, sidetracking, infilling and boosting can obtain the highest gas recovery, while the scheme with patching holes and sidetracking has the best economic benefits. To balance the gas recovery and economics, the measurement of patching holes, sidetracking and infilling with vertical wells is utilized. In the final production period, compared with the basic schemes, the gas recovery can increase by 5.5%. The primary novelty of this paper lies in the determination of the optimal infilling well types and its presentation of a comprehensive adjustment workflow for EGR in tight gas reservoirs. The conclusions in this paper can provide some guidance for other similar tight gas reservoirs developed with MFHWs in the later period. [ABSTRACT FROM AUTHOR]

With the deepening of exploration and development of tight sandstone gas reservoirs, the remaining recoverable reservoirs gradually become thinner with the vertical stratigraphic structure. The geomechanical properties become complex, and development based on conventional hydraulic fracturing methods often leads to serious problems, such as difficult control of fracture height, penetrating interlayers, too short fracture length, and inadequate proppant filling. In view of the above problems, we conducted a numerical investigation on a hydraulic fracturing scheme in a multi-layered and thin tight sandstone gas reservoir. According to the dataset from wells in a real gas reservoir in China's Ordos Basin, the relevant geomechanical characteristics of the gas layers, together with the interlayers in the main production interval, were obtained, based on which, a fine numerical model was developed. By using the PL3D fracture propagation algorithm, a 3D hydraulic fracture propagation model was produced, and then using microseismic monitoring and production data matching, a high-precision hydraulic fracture model of the multi-layered and thin tight sandstone gas reservoir was obtained. On this basis, the influence of different geomechanical parameters and fracturing operational parameters on hydraulic fracture propagation was analyzed. Finally, an optimized hydraulic fracturing scheme that fitted the characteristics of the multi-layered and thin tight sandstone gas reservoir was proposed. Using a typical reservoir example, the optimized scheme enabled control of the fracture height in thin layers and the creation of long fractures with better proppant filling, so that the productivity of the fracture was significantly improved. [ABSTRACT FROM AUTHOR]

Repetitive operation is extensively present in the inverter compressor refrigeration field. Research illustrates that an approximate periodic load disturbance deteriorates its self-sensing and efficiency in a low frequency range. According to an internal model theorem, a repetitive controller can realize periodic signal tracking or suppression; however, ideal repetitive control (IRC) can not be directly employed in practical application owing to its excessive sensitivity to period-time uncertainties or aperiodic component, etc. In addition, the ratio between period delay to sampling time can not always maintain an integer which causes the resonant frequencies to deviate from the interested. Even if the ratio is a fixed integer, the auxiliary function for stabilization in a conventional repetitive controller can result in the steady state tracking error. In this paper, a revised repetitive controller with a novel Savitzky–Golay (S–G) filter is proposed, the S–G filter cascaded with a traditional delay element can approximate the delay element with any ratio. Aiming at a different operating condition, a second order generalized integrator (SOGI) based observer is employed to extract disturbance fundamental component, and Steiglitz–McBride based adaptive notch filter (SM-ANF) is adopted for frequency estimation. The proposed scheme varies the S–G filter according to variable fundamental frequency and maintains its resonant frequencies corresponding with the fundamental and harmonic disturbance. In the end, simulations and experiments are implemented and results illustrate that speed fluctuation can be effectively suppressed by the proposed method. [ABSTRACT FROM AUTHOR]

Repetitive operations have been extensively used in the inverter compressor refrigeration industry. The approximately periodic disturbance caused by repetitive operations must be compensated to realize stable and high-efficiency operation. In this paper, a periodic disturbance observer (PDOB) is proposed to tackle the speed fluctuation of an inverter compressor in the low-frequency range. Periodic disturbance, consisting of a fundamental wave and corresponding harmonics, can thus be estimated and compensated; in addition, sensitivity and complementary sensitivity can reach a compromise through the use of a certain parameter. Aiming at a different operation environment, an adaptive notch filter based on the Steiglitz–McBride method is employed to estimate the fundamental frequency of periodic disturbance. Finally, the feasibility of our approach is verified by MATLAB simulation, and experiments are implemented to illustrate that speed fluctuation can be more effectively attenuated by the proposed method in comparison with general DOB. [ABSTRACT FROM AUTHOR]