Search

High penetration of renewable energy sources into isolated microgrids (µGs) is considered a critical challenge, as µGs' operation at low inertia results in frequency stability problems. To solve this challenge, virtual inertia control based on an energy storage system is applied to enhance the inertia and damping properties of the µG. On the other hand, utilization of a phase-locked loop (PLL) is indispensable for measuring system frequency; however, its dynamics, such as measurement delay and noise generation, cause extra deterioration of frequency stability. In this paper, to improve µG frequency stability and minimize the impact of PLL dynamics, a new optimal frequency control technique is proposed. A whale optimization algorithm is used to enhance the virtual inertia control loop by optimizing the parameters of the virtual inertia controller with consideration of PLL dynamics and the uncertainties of system inertia. The proposed controller has been validated through comparisons with an optimized virtual inertia PI controller which is tuned utilizing MATLAB internal model control methodology and with H ∞ -based virtual inertia control. The results show the effectiveness of the proposed controller against different operating conditions and system disturbances and uncertainties. [ABSTRACT FROM AUTHOR]

This study proposes a classical control algorithm for solving the transcendental set of equations for the unequal DC sources of five-level multilevel inverters (MLIs). Such sources can be generated from renewable energy sources. Two DC sources with different values are used to produce an output voltage with five levels. Then, a set of two transcendental equations is formulated with two targeted functions to control the fundamental component and cancel the stipulated single harmonic order. The proposed solution uses a simple classical proportional control with two loops to generate two switching angles. The first switching angle is assigned with an initial value, whereas the second one is calculated from the inner loop. The outer loop is used to cancel the specified harmonic by sending the error signal to the proposed proportional control that tunes the switching angles. The proposed algorithm is easy, fast, and accurate, and has a wide-range solution in terms of modulation index ( MI ) and input DC source ratio ( x = V 1 V 2 ≤ 1 ). The proposed algorithm is tested for a wide range of MI and x to verify its feasibility. Moreover, several simulation and laboratory tests are presented to further validate the applicability of the proposed approach. [ABSTRACT FROM AUTHOR]

The increase in operating temperature of PV generators leads to degradation of their performance. These adverse effects of high temperatures are considered as one of the most important problems that solar panel operation faces in hot weather areas. A lot of research has been undertaken to study this aspect and find ways of limiting the harm caused by such high temperatures. To overcome this harm and to maintain the operating temperature of the PV cells within the optimum range specified by manufacturers, cooling the solar panels often becomes indispensable. This paper discusses the heat transfer through the solar panel layers and studies the effect of high temperature on the solar panel performance in a hot desert environment. It also presents the development of a new solar panel structure viz. by installing an aluminum heat sink to reduce the effect of temperature rise and thus improve the solar panel performance. The study focuses on a pole-mounted solar panel for a street lighting apparatus in extremely hot desert conditions with fluctuating wind speeds. It will be shown that adding an aluminum heat sink to the solar panel bottom mitigates the effect of increased temperature and hence modifies the solar panel operating point by increasing both the efficiency and the lifetime. The solar cell temperature is decreased by 16.4% as a result of the aluminum heat sink installation on the solar panel back sheet and consequently, the accumulated energy produced by the the solar panel is increased by 13.23% per day. [ABSTRACT FROM AUTHOR]

Microinverters are an essential part of the photovoltaic (PV) industry with significant exponential prevalence in new PV module architectures. However, electrolyte capacitors used to decouple double line frequency make the single-phase microinverters topologies the slightest unit in this promising industry. Three-phase microinverter topologies are the new trend in this industry because they do not have double-line frequency problems and they do not need the use of electrolyte capacitors. Moreover, these topologies can provide additional features such as four-wire operation. This paper presents a detailed discussion of the strong points of three-phase microinverters compared to single-phase counterparts. The developed topologies of three-phase microinverters are presented and evaluated based on a new classification based on the simplest topologies among dozens of existing inverters. Moreover, the paper considers the required standardized features of PV, grid, and the microinverter topology. These features have been classified as mandatory and essential. Examples of the considered features for classifications are Distributed Maximum Power Point Tracking (DMPPT), voltage boosting gain, and four-wire operation. The developed classification is used to identify the merits and demerits of the classified inverter topologies. Finally, a recommendation is given based on the classified features, chosen inverter topologies, and associated features. [ABSTRACT FROM AUTHOR]

Maximum Power Point Tracking (MPPT) control is an essential part of every photovoltaic (PV) system, in order to overcome any change in ambient environmental conditions and ensure operation at maximum power.. Recently, micro-inverters have gained a lot of attention due to their ability to track the true MPP for each individual PV module, which is considered a powerful solution to overcome the partial shading and power mismatch problems which exist in series-connected panels. Although the LLC resonant converter has high efficiency and high boosting ability, traditional MPPT techniques based on Pulse Width Modulation (PWM) do not work well with it. In this paper, a fixed frequency predictive MPPT technique is presented for the LLC resonant converter to be used as the first-stage in a PV micro-inverter. Using predictive control enhances the tracking efficiency and reduces the steady state oscillation. Operation with fixed switching frequency for the LLC resonant converter improves the total harmonic distortion profile of the system and ease the selection of circuit magnetic component. To demonstrate the effectiveness of the proposed MPPT technique, the system is simulated using MATLAB/Simulink platform. Furthermore, a 150 W hardware prototype is developed and tested. Both simulation and experimental results are consistent and validate the proper operation of the developed system. [ABSTRACT FROM AUTHOR]

AC-DC LED drivers may have a lifespan shorter than the lifespan of LED chips if electrolytic capacitors are used in their construction. Using film capacitors solves this problem but, as their capacitance is considerably lower, the low-frequency ripple will increase. Solving this problem by limiting the output ripple to safe values is possible by distorting the input current using harmonic injection technique, as long as these harmonics still complies with Power Factor Regulations (Energy Star). This harmonic injection alleviates the requirements imposed to the output capacitor in order to limit the low-frequency ripple in the output. This idea is based on the fact that LEDs can be driven by pulsating current with a limited Peak-To-Average Ratio (PTAR) without affecting their performance. By considering the accurate model of LEDs, instead of the typical equivalent resistance, this paper presents an improved and more reliable calculation of the intended harmonic injection. Wherein, its orders and values can be determined for each input/output voltage to obtain the specified PTAR and Power Factor (PF). Also, this harmonic injection can be simply implemented using a single feedback loop, its control circuit has features of wide bandwidth, simple, single-loop and lower cost. A 21W AC-DC buck converter is built to validate the proposed circuit and the derived mathematical model and it complies with IEC61000 3-2 class D standard. [ABSTRACT FROM AUTHOR]