Search

This article presents a complex and exhaustive review of the integration of renewable energy sources (RES) (specifically solar, geothermal, and hydraulic energies and heat pumps (HPs)) and the improvement of water pumping in district heating systems (DHSs) focused on low-temperature systems, to increase energy efficiency and environmental protection. For this aim, the main components of a DHS and the primary RES with applications in DHSs were described briefly. Finally, several case studies regarding the DHS in Timisoara, Romania, were analysed. Thus, by integrating water source HP (WSHP) systems in cooperation with solar thermal and photovoltaic (PV) collectors and reducing the supply temperature from 110 °C to 30 °C in DHS, which supplies the water radiators to consumers in a district of this city in a 58/40 °C regime of temperatures and produces domestic hot water (DHW) required by consumers at 52 °C, a thermal energy saving of 75%, a reduction in heat losses on the transmission network of 90% and a diminution of CO2 emissions of 77% were obtained. Installed PV panels generate 1160 MWh/year of electricity that is utilised to balance the electricity consumption of HP systems. Additionally, mounting pumps as turbines (PATs) for the recovery of excess hydraulic energy in the entire heating network resulted in electricity production of 378 MW, and the variable frequency drive's (VFD) method for speed control for a heating station pump resulted in roughly 38% more energy savings than the throttle control valve technique. [ABSTRACT FROM AUTHOR]

A ground-coupled heat pump (GCHP) system used to provide the space heating for an office room is a renewable, high performance technology. This paper discusses vapour compression-based HP systems, briefly describing the thermodynamic cycle calculations, as well as the coefficient of performance (COP) and CO2 emissions of a HP with an electro-compressor and compares different heating systems in terms of energy consumption, thermal comfort and environmental impact. It is focused on an experimental study performed to test the energy efficiency of the radiator or radiant floor heating system for an office room connected to a GCHP. The main performance parameters (COP and CO2 emissions) are obtained for one month of operation of the GCHP system, and a comparative analysis of these parameters is presented. Additionally, two numerical simulation models of useful thermal energy and the system COP in heating mode are developed using the Transient Systems Simulation (TRNSYS) software. Finally, the simulations obtained from TRNSYS software are analysed and compared to the experimental data, showing good agreement and thus validating the simulation models. [ABSTRACT FROM AUTHOR]

Ground-coupled heat pumps (GCHPs) are an efficient thermal energy production system that can satisfy the gap between heating and air-conditioning. Be that as it may, exploratory research on GCHPs is still lacking. The first objective of this article is to describe a utilitarian energy-efficiency improvement device for a vertical GCHP system that includes a buffer tank (BT) between the heat pump unit and the fan coil units and user supply, utilizing the quantitative regulation of water flow rate with a variable-speed circulation pump. At that point, the investigative estimations are utilized to test the performances of the GCHP system in various operating modes. Fundamental efficiency parameters (coefficient of performance (COP) and CO2 emission) are achieved for one month of running utilizing two control strategies of the GCHP—standard and optimized regulation of the water pump speed—and a benchmarking of these parameters is achieved. Exploratory research has indicated higher efficiency of the system for the flow regulation solution utilizing a BT and programmed control equipment for the circulation pump speed compared with the standard regulation solution (COPsys with 7–8% higher and CO2 emission level 7.5–8% lower). The second objective is to elaborate a simulation model of the necessary heat/cold in heating and air-conditioning periods, utilizing the Transient Systems Simulation (TRNSYS) program. Finally, the simulation, acquired utilizing the TRNSYS program, is analyzed and compared with experimental information, leading to a good agreement and, along these lines, the simulation model is approved. [ABSTRACT FROM AUTHOR]

The research explores the potential of digital-twin-based methods and approaches aimed at achieving an intelligent optimization and automation system for energy management of a residential district through the use of three-dimensional data model integrated with Internet of Things, artificial intelligence and machine learning. The case study is focused on Rinascimento III in Rome, an area consisting of 16 eight-floor buildings with 216 apartment units powered by 70% of self-renewable energy. The combined use of integrated dynamic analysis algorithms has allowed the evaluation of different scenarios of energy efficiency intervention aimed at achieving a virtuous energy management of the complex, keeping the actual internal comfort and climate conditions. Meanwhile, the objective is also to plan and deploy a cost-effective IT (information technology) infrastructure able to provide reliable data using edge-computing paradigm. Therefore, the developed methodology led to the evaluation of the effectiveness and efficiency of integrative systems for renewable energy production from solar energy necessary to raise the threshold of self-produced energy, meeting the nZEB (near zero energy buildings) requirements. [ABSTRACT FROM AUTHOR]

Innovative toilets can save resources, but have higher embodied impacts associated with materials and electronic components. This article presents an environmental life-cycle assessment (LCA) of an innovative multifunctional toilet (WashOne) for two alternative configurations (with or without washlet), comparing its performance with those of conventional systems (toilet and bidet). Additionally, two scenario analyses were conducted: (i) user behavior (alternative washlet use patterns) and (ii) user location (Portugal, Germany, the Netherlands, Sweden and Saudi Arabia). The results show that the WashOne with washlet has a better global environmental performance than the conventional system, even for low use. It also reveals that the use phase has the highest contribution to impacts due to electricity consumption. User location analysis further shows that Sweden has the lowest environmental impact, while Germany and the Netherlands have the highest potential for impact reduction when changing from a conventional system to the WashOne. Based on the overall results, some recommendations are provided to enhance the environmental performance of innovative toilet systems, namely the optimization of the washlet use patterns. This article highlights the importance of performing a LCA at an early stage of the development of innovative toilets by identifying the critical issues and hotspots to improve their design and performance. [ABSTRACT FROM AUTHOR]

Developing accurate models is necessary to optimize the operation of heating systems. A large number of field measurements from monitored heat pumps have made it possible to evaluate different heat pump models and improve their accuracy. This study used measured data from a heating system consisting of three heat pumps to compare five regression and two artificial neural network (ANN) models. The models' performance was compared to determine which model was suitable during the design and operation stage by calibrating them using data provided by the manufacturer and the measured data. A method to refine the ANN model was also presented. The results indicate that simple regression models are more suitable when only manufacturers' data are available, while ANN models are more suited to utilize a large amount of measured data. The method to refine the ANN model is effective at increasing the accuracy of the model. The refined models have a relative root mean square error (RMSE) of less than 5%. [ABSTRACT FROM AUTHOR]

The objective of this study was to modify an existing liquid desiccant and indirect/direct evaporative cooling-assisted 100% outdoor air system (LD-IDECOAS) for humidification operation in winter. The energy benefit of the liquid desiccant-assisted humidification approach during the operation of LD-IDECOAS over the conventional method with a steam humidifier was evaluated through a detailed energy simulation. The humidification and enthalpy effectiveness values of the liquid desiccant humidification measured from laboratory tests were 0.41 and 0.49, respectively, which were applied to the energy simulation for the modified system. Both systems with the proposed and conventional humidification approaches were simulated using an engineering equation solver combined with a TRNSYS 18 energy simulation program. The results demonstrated that the modified LD-IDECOAS consumes less energy for humidification compared to the existing system with a steam humidifier. The proposed system also exhibited considerable heating energy-saving potential. Consequently, modified LD-IDECOAS consumed 42% less primary energy during winter operation after being modified for liquid desiccant-assisted humidification. [ABSTRACT FROM AUTHOR]

Latent heat thermal energy storage systems allow storing large amounts of energy in relatively small volumes. Phase change materials (PCMs) are used as a latent heat storage medium. However, low thermal conductivity of most PCMs results in long melting (charging) and solidification (discharging) processes. This study focuses on the PCM melting process in a fin-and-tube type copper heat exchanger. The aim of this study is to define analytically natural convection heat transfer coefficient and compare the results with experimental data. The study shows how the local heat transfer coefficient changes in different areas of the heat exchanger and how it is affected by the choice of characteristic length and boundary conditions. It has been determined that applying the calculation method of the natural convection occurring in the channel leads to results that are closer to the experiment. Using this method, the average values of the heat transfer coefficient (have) during the entire charging process was obtained 68 W/m2K, compared to the experimental result have = 61 W/m2K. This is beneficial in the predesign stage of PCM-based thermal energy storage units. [ABSTRACT FROM AUTHOR]

This paper proposes an energy management system (EMS) of direct current (DC) microgrid. In order to implement the proposed EMS, the control and operation method of EMS is presented in this work. While most of the studies have individually examined the grid-connected mode used in building and the stand-alone operation mode applicable to the island, the proposed EMS allows it to be used in both grid-connected mode and stand-alone mode with 10 modes. In order to determine each mode in EMS, not only the amount of generated power, load power, and the state of charge (SOC) of the battery, but also the rated power of the energy storage system (ESS) converter that performs charging and discharging operations is additionally considered. Thus, various uncertainties that may occur in the actual DC microgrid environment can be improved. A laboratory-scale DC microgrid is fabricated to conduct experimental validation of proposed EMS. Experiments of DC microgrid with proposed EMS were performed for each mode, and the experiment waveforms of each power conversion device are included in detail. [ABSTRACT FROM AUTHOR]