Search

The photovoltaic literature contains a wide range of methods for translating the I–V curves of a solar device to other conditions of irradiance and cell temperature, different from those under which the measurements were performed. Some of these translation methods are included as part of the International Standard IEC 60891. In this paper, these techniques are classified, reviewed, and implemented to perform a deep comparative analysis between them and to discuss their suitability for converting the I–V curves of photovoltaic modules under different scenarios of irradiance and temperature. From the analysis conducted, it can be seen that the interpolation method proposed in IEC 60891 achieves accurate results when it is applied to correct small and medium irradiance and temperature gaps. If no interpolation is possible and for large irradiance corrections, other procedures described in IEC 60891 can be applied. However, certain explicit methods based on the single-diode model or on the double-diode model can overcome the most well-known approaches proposed by the standard. [ABSTRACT FROM AUTHOR]

This paper reviews the current techniques used in energy management systems to optimize energy schedules into microgrids, accounting for uncertainties for various time frames (day-ahead and real-time operations). The current uncertainties affecting applications, including residential, commercial, virtual power plants, electric mobility, and multi-carrier microgrids, are the main subjects of this article. We outline the most recent modeling approaches to describe the uncertainties associated with various microgrid applications, such as prediction errors, load consumption, degradation, and state of health. The modeling approaches discussed in this article are probabilistic, possibilistic, information gap theory, and deterministic. Then, the paper presents and compares the current optimization techniques, considering the uncertainties in their problem formulations, such as stochastic, robust, fuzzy optimization, information gap theory, model predictive control, multiparametric programming, and machine learning techniques. The optimization techniques depend on the model used, the data available, the specific application, the real-time platform, and the optimization time. We hope to guide researchers to identify the best optimization technique for energy scheduling, considering the specific uncertainty and application. Finally, the most challenging issues to enhance microgrid operations, despite uncertainties by considering new trends, are discussed. [ABSTRACT FROM AUTHOR]

The DC-link capacitor is one of the components that are more prone to faults in energy-distributed systems based on voltage source inverters. A predictive maintenance approach should allow to foresee the risk of an unexpected system shutdown. In this study, a two-stage diagnostic approach that is aimed at determining the health status of the DC-link capacitor in a single-phase grid-connected PV system was proposed. The equivalent series resistance (ESR) and the capacitance (C) values were used as indicators in the estimation of the degradation stage. Electrochemical impedance spectroscopy (EIS) was used to estimate the impedance curve of the DC-link capacitor, and a multi-fitting algorithm allowed us to determine the ESR and C parameters. A comparison between the estimated values C and ESR and the nominal values was used to quantify the fault severity. It was demonstrated that the EIS allowed the determination of the capacitor impedance regardless of the actual operating conditions of the photovoltaic generator, such as during irradiance changes and with the maximum power point algorithm turned off. By using the capacitor simplified model and a multi-fitting algorithm, the C and ESR values were estimated with an error that was lower than 1%. An analysis of the hardware required to implement the proposed approach in real applications by achieving the desired accuracy was also proposed. [ABSTRACT FROM AUTHOR]

Online/on-board diagnosis would help to improve fuel cell system durability and output power. Therefore, it is a feature the manufacturers may wish to provide for final users to increase the attractiveness of their product. This add-on requires suitable stack models, parametric identification tools and diagnostic algorithms to be run on low-cost embedded systems, ensuring a good trade-off between accuracy and computation time. In this paper, a computational approach for the impedance parameter identification of polymer electrolyte membrane fuel cell stack is proposed. The method is based on an evolutionary algorithm including sub-population and migration features, which improves the exploration capability of the search space. The goal of the evolutionary algorithm is to find the set of parameters that minimizes an objective function, representing the mismatch between two impedance plots in a normalized plane. The first plot is associated with experimental impedance and the second is computed on the basis of the identified parameters using a circuit model. Three kinds of impedance models, characterized by increasing computational complexity, are used, depending on the experimental data—a linear model made of resistors and capacitors, the Fouquet model and the Dhirde model. Preliminary analysis of the experimental impedance data may evidence correlations among parameters, which can be exploited to reduce the search space of an evolutionary algorithm. The computational approach is validated with literature data in a simulated environment and with experimental data. The results show good accuracy and a computational performance that fits well with the commercial embedded system hardware resources. The implementation of the approach on a low-cost off-the-shelf device achieves small computation times, confirming the suitability of such an approach to online/on-board applications. From a diagnostic perspective, the paper outlines a diagnostic approach based on the identified impedance parameters, on the basis of a small set of experimental data including fuel cell stack faulty conditions. [ABSTRACT FROM AUTHOR]

Photovoltaic (PV) arrays can be connected following regular or irregular connection patterns to form regular configurations (e.g., series-parallel, total cross-tied, bridge-linked, etc.) or irregular configurations, respectively. Several reported works propose models for a single configuration; hence, making the evaluation of arrays with different configuration is a considerable time-consuming task. Moreover, if the PV array adopts an irregular configuration, the classical models cannot be used for its analysis. This paper proposes a modeling procedure for PV arrays connected in any configuration and operating under uniform or partial shading conditions. The procedure divides the array into smaller arrays, named sub-arrays, which can be independently solved. The modeling procedure selects the mesh current solution or the node voltage solution depending on the topology of each sub-array. Therefore, the proposed approach analyzes the PV array using the least number of nonlinear equations. The proposed solution is validated through simulation and experimental results, which demonstrate the proposed model capacity to reproduce the electrical behavior of PV arrays connected in any configuration. [ABSTRACT FROM AUTHOR]