Search

During the building design phase, a lot of attention is paid to the thermal properties of the external envelopes. New regulations are introduced to improve energy efficiency of a building and impose a reduction of the overall heat transfer coefficient; meanwhile, this efficiency is more influenced by the efficiency of the heating system and the type of fuels used. This article presents a complex analysis including the impact of: heat transfer coefficient of the envelope, efficiency of building service systems, the type of energy source, and the fuel. The analysis was based on the results of simulation tests obtained for an exemplary multi-family residential building located in Poland that is not equipped with a cooling system. The conducted calculations gave quantitative evaluation of the influence of particular parameters on building energy performance and showed that the decrease of heat transfer coefficient of building boundaries, in accordance to the Polish regulation for 2017 and 2021, gave only 11% of reduction on usable energy demand index. On the other hand, it was found that modification of the heating system and heat source can significantly influence the values of the final and primary energy consumption at the level of 70%. The application of heat pumps has a greater influence on the final and primary energy consumption for heating indices than other parameters, such as the building's envelopes. [ABSTRACT FROM AUTHOR]

The article presents the results of studies concerning raw hemp shives obtained from the Polish crop of industrial hemp as a loose-fill thermal insulation material. The study focuses mainly on the measurements of the pore size distribution, thermal conductivity and air permeability of material. An increase in the value of the thermal conductivity coefficient (0.049–0.052 W/(m·K)) was demonstrated with an increase in the bulk density. The porosity of the individual pieces of shives is 78.7% and the predominant number of pores is in the diameter range of 0.9–3 μm. The paper also presents an example of the use of the tested material as thermal insulation of the wooden frame wall. The heat flow analysis was performed in various wall variants (insulation thickness: 100, 200 and 300 mm and pressure difference 0, 5, 10 and 15 Pa). A clear influence of the variables on the temperature distribution was observed. [ABSTRACT FROM AUTHOR]

The article assesses an impact of thermal retrofitting on an improvement of the energy quality of public buildings in terms of their heating. The analysis covered a group of 14 buildings, including schools, kindergartens or offices, while energy audits were carried out for 12 of them. The indications of individual gas meters were the source of actual data for the assessment of changes in energy consumption indexes in operating conditions. The analysis showed a clear improvement in the energy quality of buildings; however, the actual effects were much lower than forecasted. The average forecasted decrease in energy consumption was supposed to be 64.3%, but the measured data showed only 37.1%. The investigation confirmed that the most complex refurbishing provided the most satisfactory decrease in energy consumption (51.4% of real decrease in energy consumption), while objects with partial thermal refurbishing reached an efficiency of only 21.8%. It was stated that in operating conditions, special attention should be paid to the manner of energy use, since different indicators of energy consumption can be obtained with the same parameters of building's balance cover. The results obtained can be further utilized in thermal-refurbishment implementation procedures. Follow-up investigations on the impact of selected parameters on energy consumption are planned. [ABSTRACT FROM AUTHOR]

The paper presented the analysis of heat consumption for heating in multi-family residential buildings before and after thermal retrofitting. The analysis involved four groups of buildings, i.e., 43 buildings in total, located in various localities, belonging to one weather station. The predicted level of energy savings resulting from thermal retrofitting was achieved from the energy audits. The actual heat consumption, following the calculation into so-called external standard conditions, was obtained based on the readouts from heat-meters. For each building, the values of heat consumption over the periods of 6–10 years were read. The performance measurements involved the periods before, during, and after thermal retrofitting. The following statistical tests were used for data analysis: Wilcoxon–Mann–Whitney, Shapiro–Wilk, Bartlett, ANOVA, Kruskal–Wallis, Dunn and Holm post-hoc. The performed analyses showed that the mean value of energy savings predicted by audits reached 38.5% when the real mean value of savings, achieved from heat-meters, equaled 30.3%. The annual energy demand factors for heating were calculated for final energy and non-renewable primary energy factors. It was established that most of the analyzed objects fulfilled the primary energy factor requirements found in the Polish technical and construction regulations, which were valid at the time of investment. [ABSTRACT FROM AUTHOR]

One way to decrease the greenhouse gas emissions in the building sector is to improve the building energy performance, which can be mainly achieved by the reduction of energy consumption. In the case of the existing objects, this goal could be achieved by the thermo-modernization of the building partitions and equipment. This article concerns the issue of heat consumption for heating purposes after a comprehensive retrofitting of nine educational buildings (two kindergartens and seven schools) located in south-eastern Poland where both the total efficiency of the heating installation and the thermal insulation of building partitions were improved. The evaluation of the real energy effects was made on the basis of the measurements performed over the 8 year period of operation for each building. The obtained values were compared with the boundary values of the factors that were in force in Poland during the period when all of the buildings were retrofitted. Additionally, they were compared with the results of theoretical calculations included in the energy audits of the example of three objects and an attempt to describe the reasons for the discrepancies was made. All obtained results were discussed with the available literature sources and summarized with the suitable conclusions. [ABSTRACT FROM AUTHOR]

Fired bricks represent one of the most popular building materials, of which production is still growing. Since the functional properties of bricks have reached their physical limits, the current development aims at an optimization of production procedures as it goes along with heavy environmental loads. This paper is focused on tailoring the firing procedure to optimize the energy demands. Dealing with five different clays, their heat storage properties are determined using inverse analysis of calorimetric data so that the measurement errors are reduced. Moreover, effective values incorporate the thermal processes that occur during firing. A simplified model of clay samples is then used to calculate the energy demands for reaching an optimal firing scheme. The results show that specific treatment is necessary for particular clays as the energy demands may range between 89 and 173 MJ·m−2, depending on a clay composition. The highest demands were found in the case of clays containing the high volume of calcite and dolomite, of which thermal decomposition is very energy demanding. Using the tailored firing scheme, one can reach energy savings of up to 49% while the functional properties would be preserved due to maintaining the optimal temperature evolution in the brick body. [ABSTRACT FROM AUTHOR]